This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
1. Removing and installing the flywheel, which involves using tools to secure and lift the heavy flywheel component.
2. Removing and installing the crankshaft rear seal, which requires drilling holes in the seal before pulling it off and pressing on a new seal and wear sleeve.
3. Removing and installing the flywheel housing, which involves lifting the housing off using tools and installing a new gasket.
4. Procedures for the crankshaft pulley and front seal that require pulling components off using pullers and pressing new parts on.
This document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including:
1. Removing the crankshaft rear seal using a slide hammer puller and distorter tool.
2. Installing a new crankshaft rear seal and wear sleeve using installer and locator tools.
3. Removing the flywheel housing and checking the oil seal, then reinstalling the housing.
4. Removing the crankshaft pulley using a combination puller and removing the wear sleeve if needed.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...hvy7sbkw8e
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and applying retaining compounds as specified.
3. Detailed illustrations accompany each procedure to show the component locations and installation/removal steps.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...xiapokang564341
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 320C excavator engine. The removal procedure involves using a combination puller tool to pull the pulley off the crankshaft. The installation procedure specifies cleaning the crankshaft, applying retaining compound, and pressing the pulley onto the shaft with the puller tool in reverse. Proper torque is applied to secure the pulley.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 320C excavator engine. The removal procedure involves using a combination puller tool to pull the pulley off the crankshaft. The installation procedure specifies cleaning the crankshaft, applying retaining compound, and pressing the pulley onto the shaft with the puller tool in reverse. Proper torque is applied to secure the pulley.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...wenxian17880
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and apply retaining compounds as needed.
3. Safety notices are provided to contain fluids and wear protective gloves when handling hot parts.
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and applying retaining compounds as specified.
3. Detailed illustrations accompany each procedure to show the component locations and installation/removal steps.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including:
1. Removing the crankshaft rear seal using a slide hammer puller and distorter tool.
2. Installing a new crankshaft rear seal and wear sleeve using installer and locator tools.
3. Removing the flywheel housing and checking the oil seal, then reinstalling the housing.
4. Removing the crankshaft pulley using a combination puller and removing the wear sleeve if needed.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...hvy7sbkw8e
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and applying retaining compounds as specified.
3. Detailed illustrations accompany each procedure to show the component locations and installation/removal steps.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...xiapokang564341
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 320C excavator engine. The removal procedure involves using a combination puller tool to pull the pulley off the crankshaft. The installation procedure specifies cleaning the crankshaft, applying retaining compound, and pressing the pulley onto the shaft with the puller tool in reverse. Proper torque is applied to secure the pulley.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 320C excavator engine. The removal procedure involves using a combination puller tool to pull the pulley off the crankshaft. The installation procedure specifies cleaning the crankshaft, applying retaining compound, and pressing the pulley onto the shaft with the puller tool in reverse. Proper torque is applied to secure the pulley.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...wenxian17880
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and apply retaining compounds as needed.
3. Safety notices are provided to contain fluids and wear protective gloves when handling hot parts.
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and applying retaining compounds as specified.
3. Detailed illustrations accompany each procedure to show the component locations and installation/removal steps.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for assembling the governor of a 3116 engine. It describes:
1) Mounting various parts like the drive gear, C spring, and fuel ratio control lever.
2) Installing the governor output servo assembly by pressing in the clevis and spring pin.
3) Assembling other internal parts like the bearing block, riser lever, and torque cam.
4) Adjusting the gap for the torque cam using special tools to set the proper dimension.
This document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators. It describes the parts and tools needed and steps to disassemble three starting motor models: 42-MT, 37-MT, and 41-MT. The instructions cover removing components like the rear housing, brushes, pinion drive, shift lever housing, and field winding coil. Cleaning and inspection steps are also included. The goal is to repair or replace worn parts to restore the starting motors to working condition.
This document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators. It describes the parts and tools needed and steps to disassemble three starting motor models: 42-MT, 37-MT, and 41-MT. The instructions cover removing components like the rear housing, brushes, pinion drive, shift lever housing, and field winding coil. Cleaning and inspection steps are also included. The goal is to repair or replace worn parts to restore the starting motors to working condition.
This document provides instructions for removing and installing a radiator on a Caterpillar 906 Compact Wheel Loader. The removal procedure involves:
1. Draining the coolant and removing the radiator fill cap.
2. Removing mounting bolts and brackets to detach the radiator.
3. Using straps to lift out the radiator.
The installation procedure describes cleaning and inspecting parts before reversing the removal steps to mount the new radiator, refill the cooling system, and replace the hood. Safety precautions are provided to avoid burns from hot coolant and ensure fluids are contained.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
The document provides instructions for removing and installing various components of a Caterpillar 903C2 compact wheel loader engine, including:
- Removing and installing the fuel manifold by removing bolts and disconnecting fuel injection lines.
- Removing and installing fuel injection lines by disconnecting hoses and removing clamps and bolts.
- Removing and installing the turbocharger by removing intake hoses and disconnecting pipes.
- Removing and installing the exhaust gas recirculation valve by removing bolts, clamps, and disconnecting hoses.
This document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It includes procedures for removing and installing fuel injection lines and nozzles, as well as removing, installing, disassembling and assembling the governor and camshaft. Removal and installation procedures note the need to keep parts clean and plug all openings to prevent contamination. Disassembly and assembly sections provide illustrations and detail each step, such as pressing components apart and together using the specified tools.
This document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader powered by a C2.4 engine. It describes procedures for removing and installing fuel injection lines and nozzles, and removing, disassembling, and reassembling the governor and camshaft. The document includes illustrations and specifies required tools and torque specifications for reinstallation.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a 527 Track Skidder with a 3304 engine. The procedures include removing bolts and hoses, checking gaskets, applying fuel to seals during installation, and ensuring parts are clean to prevent contamination. Illustrations show the component locations and part numbers.
The document provides instructions for servicing components of a Caterpillar 527 track skidder, including:
- Removing and installing the grapple crosshead from the jib boom.
- Disassembling, inspecting, and reassembling the grapple arch cylinder.
- Removing, installing, and installing the grapple arch cylinder on the arch.
The instructions include illustrations of the components and multi-step procedures for servicing while taking safety precautions for working with heavy equipment and hydraulic systems. Required tools are also listed.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
The document provides instructions for removing and installing a cab on a 438C BACKHOE LOADER model. It describes removing the rear wheels first, then removing screws and components to detach the cab, including vents, ducts, trim, radio mount, wiring, and bolts. The reverse process is described for installing the cab. Safety precautions are provided for working on air conditioning systems involving refrigerants.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including:
- Water temperature regulator removal and installation in 3 steps
- Water outlet manifold removal in 5 steps and installation in 6 steps
- Flywheel removal in 6 steps and installation in 7 steps
- Crankshaft rear seal removal starting with removing the flywheel and taking out housing bolts in 3 steps
The document contains detailed diagrams and notices about keeping parts clean and containing fluids to complete the repair and replacement procedures safely.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation.
3) Installing the housing by positioning it on the cylinder block and installing mounting bolts, taking care to keep parts clean of contaminants.
This document provides instructions for removing and installing the flywheel housing on a 3054 engine for a Caterpillar 436C backhoe loader. The removal procedure involves supporting the engine, removing mounting bolts from the top and rear of the flywheel housing, and lifting the housing off with tooling. The installation procedure specifies cleaning surfaces, positioning the housing with tooling, and tightening mounting bolts to the specified torques.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
This document provides assembly instructions for the transmission of a 434E BACKHOE LOADER. It lists the required tools and notes on cleanliness and lubrication. It then provides step-by-step instructions to assemble the various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft (rear). The instructions include installing bearings, gears, springs, seals and other parts in the proper order and include safety warnings for parts under spring load.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove components including cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation, which involves reinstalling components in reverse order and applying thread lock compound to bolts. Tools required include various pullers, lifting devices, drivers and thread lock compound.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing and installing an engine on a 432E backhoe loader. It outlines 50 steps to remove the engine, which includes draining fluids, disconnecting hoses, cables, and other components. It then outlines 14 steps for installing the engine, which reverses the removal process and includes reconnecting all hoses, cables, and components in the proper order and torque specifications. The overall document provides detailed disassembly and reassembly instructions for removing and replacing the engine.
This document provides instructions for assembling the governor of a 3116 engine. It describes:
1) Mounting various parts like the drive gear, C spring, and fuel ratio control lever.
2) Installing the governor output servo assembly by pressing in the clevis and spring pin.
3) Assembling other internal parts like the bearing block, riser lever, and torque cam.
4) Adjusting the gap for the torque cam using special tools to set the proper dimension.
This document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators. It describes the parts and tools needed and steps to disassemble three starting motor models: 42-MT, 37-MT, and 41-MT. The instructions cover removing components like the rear housing, brushes, pinion drive, shift lever housing, and field winding coil. Cleaning and inspection steps are also included. The goal is to repair or replace worn parts to restore the starting motors to working condition.
This document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators. It describes the parts and tools needed and steps to disassemble three starting motor models: 42-MT, 37-MT, and 41-MT. The instructions cover removing components like the rear housing, brushes, pinion drive, shift lever housing, and field winding coil. Cleaning and inspection steps are also included. The goal is to repair or replace worn parts to restore the starting motors to working condition.
This document provides instructions for removing and installing a radiator on a Caterpillar 906 Compact Wheel Loader. The removal procedure involves:
1. Draining the coolant and removing the radiator fill cap.
2. Removing mounting bolts and brackets to detach the radiator.
3. Using straps to lift out the radiator.
The installation procedure describes cleaning and inspecting parts before reversing the removal steps to mount the new radiator, refill the cooling system, and replace the hood. Safety precautions are provided to avoid burns from hot coolant and ensure fluids are contained.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
The document provides instructions for removing and installing various components of a Caterpillar 903C2 compact wheel loader engine, including:
- Removing and installing the fuel manifold by removing bolts and disconnecting fuel injection lines.
- Removing and installing fuel injection lines by disconnecting hoses and removing clamps and bolts.
- Removing and installing the turbocharger by removing intake hoses and disconnecting pipes.
- Removing and installing the exhaust gas recirculation valve by removing bolts, clamps, and disconnecting hoses.
This document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It includes procedures for removing and installing fuel injection lines and nozzles, as well as removing, installing, disassembling and assembling the governor and camshaft. Removal and installation procedures note the need to keep parts clean and plug all openings to prevent contamination. Disassembly and assembly sections provide illustrations and detail each step, such as pressing components apart and together using the specified tools.
This document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader powered by a C2.4 engine. It describes procedures for removing and installing fuel injection lines and nozzles, and removing, disassembling, and reassembling the governor and camshaft. The document includes illustrations and specifies required tools and torque specifications for reinstallation.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a 527 Track Skidder with a 3304 engine. The procedures include removing bolts and hoses, checking gaskets, applying fuel to seals during installation, and ensuring parts are clean to prevent contamination. Illustrations show the component locations and part numbers.
The document provides instructions for servicing components of a Caterpillar 527 track skidder, including:
- Removing and installing the grapple crosshead from the jib boom.
- Disassembling, inspecting, and reassembling the grapple arch cylinder.
- Removing, installing, and installing the grapple arch cylinder on the arch.
The instructions include illustrations of the components and multi-step procedures for servicing while taking safety precautions for working with heavy equipment and hydraulic systems. Required tools are also listed.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
The document provides instructions for removing and installing a cab on a 438C BACKHOE LOADER model. It describes removing the rear wheels first, then removing screws and components to detach the cab, including vents, ducts, trim, radio mount, wiring, and bolts. The reverse process is described for installing the cab. Safety precautions are provided for working on air conditioning systems involving refrigerants.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including:
- Water temperature regulator removal and installation in 3 steps
- Water outlet manifold removal in 5 steps and installation in 6 steps
- Flywheel removal in 6 steps and installation in 7 steps
- Crankshaft rear seal removal starting with removing the flywheel and taking out housing bolts in 3 steps
The document contains detailed diagrams and notices about keeping parts clean and containing fluids to complete the repair and replacement procedures safely.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation.
3) Installing the housing by positioning it on the cylinder block and installing mounting bolts, taking care to keep parts clean of contaminants.
This document provides instructions for removing and installing the flywheel housing on a 3054 engine for a Caterpillar 436C backhoe loader. The removal procedure involves supporting the engine, removing mounting bolts from the top and rear of the flywheel housing, and lifting the housing off with tooling. The installation procedure specifies cleaning surfaces, positioning the housing with tooling, and tightening mounting bolts to the specified torques.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
This document provides assembly instructions for the transmission of a 434E BACKHOE LOADER. It lists the required tools and notes on cleanliness and lubrication. It then provides step-by-step instructions to assemble the various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft (rear). The instructions include installing bearings, gears, springs, seals and other parts in the proper order and include safety warnings for parts under spring load.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove components including cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation, which involves reinstalling components in reverse order and applying thread lock compound to bolts. Tools required include various pullers, lifting devices, drivers and thread lock compound.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing and installing an engine on a 432E backhoe loader. It outlines 50 steps to remove the engine, which includes draining fluids, disconnecting hoses, cables, and other components. It then outlines 14 steps for installing the engine, which reverses the removal process and includes reconnecting all hoses, cables, and components in the proper order and torque specifications. The overall document provides detailed disassembly and reassembly instructions for removing and replacing the engine.
Khushmeet Khushi Resume of manufacturing industry Khushmeet Khushi
A result oriented professional working for Process and New Technology of Manufacturing industry presently associated with Manufacturing Industry as
Asst. Manager in Research & Development. Skilled in manufacturing Process of various type of cords, cables, connector, wire Harness, Remote Control devices, Switches including backward integration thereof. Acquired knowledge of New product and process development, QMS, Compliance and product certification, IPQC, Product & process Stranded, Lean Manufacturing Methodology, and problem solving methodology, VAVE, Etc.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR RAW
Configuration: 320C & 320C L Excavators RAW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 15:04:02 UTC+0800 2019
3/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR RAW
Configuration: 320C & 320C L Excavators RAW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 15:04:58 UTC+0800 2019
3/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR RAW
Configuration: 320C & 320C L Excavators RAW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 15:05:54 UTC+0800 2019
3/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR RAW
Configuration: 320C & 320C L Excavators RAW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 15:06:49 UTC+0800 2019
3/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR RAW
Configuration: 320C & 320C L Excavators RAW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 15:07:45 UTC+0800 2019
4/4(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR RAW
Configuration: 320C & 320C L Excavators RAW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 15:08:41 UTC+0800 2019
2/2(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR RAW
Configuration: 320C & 320C L Excavators RAW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 28 15:09:36 UTC+0800 2019
2/2(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR RAW
Configuration: 320C & 320C L Excavators RAW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 2 g00611569
3. Remove idler gear (3) from the idler gear shaft.
Illustration 3 g00611570
4. If necessary, use Tool (B) to remove bushing (4) (not shown) from idler gear (3) .
Illustration 4 g00611572
3/5(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 5 g00611573
5. The following items are components of Tool (A) .
◦ 9U-6147 Stud (6)
◦ 6V-8231 Nut (7)
◦ 9U-6146 Sleeve Assembly (8)
◦ 8T-4244 Nut (9)
6. Use Tool (A) and remove idler shaft (5) from the cylinder block. Check the idler shaft for
wear and damage. Replace the shaft, if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
• In order to remove the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Remove".
• In order to remove the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel
Injection Pump - Remove".
• In order to remove the gear from the engine oil pump, refer to Disassembly and Assembly,
"Engine Oil Pump - Remove".
• In order to remove the crankshaft gear, refer to Disassembly and Assembly, "Crankshaft
Gear - Remove and Install".
4/5(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR RAW
Configuration: 320C & 320C L Excavators RAW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615420
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 1 g00611570
1. Use Tool (A) to install a new bushing (4) (not shown), if the bushing was removed.
Illustration 2 g00611572
2. Install idler shaft (5) onto the cylinder block.
Note: When the idler shaft is installed, ensure that the oil hole of the shaft is up. If
necessary, cool the idler shaft to 0 °C (32 °F) before installation. The temperature of the
idler shaft is lowered in order to ease the installation of the idler shaft.
Illustration 3 g00611569
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection
drive gear with the "33" mark with the "3" mark on idler gear. Make an alignment of the "2"
mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the
crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center
position when these marks are in alignment.
3. Install idler gear (3) onto the idler shaft.
2/3(W)
w
2019/9/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...