The document provides instructions for disassembling a swing drive. Key steps include:
1. Removing retaining rings, gears, bearings, washers, and other internal components from the carrier assembly and housing.
2. Using tools like retaining ring pliers and drivers to remove pins and seals.
3. Pressing out components like the shaft, bearings, and spacer from the housing.
The process involves dismantling the entire swing drive assembly into its individual parts for inspection or replacement of worn components. Cleanliness is emphasized to prevent contamination of parts.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GLA
Configuration: 320C, 320C L, 320C LN Excavators GLA00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01972529
Swing Motor - Install
SMCS - 5058-012-ZW
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
C 1U-8846 Gasket Sealant
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Prior to the installation of the swing motor, make sure that the mating surfaces of the swing
motor and the swing drive are thoroughly clean and dry.
1/6(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. 2. Apply Tooling (C) on the mating surface of the swing motor and the swing drive housing.
Illustration 1 g00694494
3. Attach Tooling (B) and a suitable lifting device to swing motor (23). The weight of swing
motor (23) is approximately 55 kg (120 lb).
Illustration 2 g00694484
4. Install the washers and bolts (20).
5. Tighten bolts (20) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
6. Install anti-reaction valve (22). Install the washers and bolts (21). Tighten bolts (21) to a
torque of 55 ± 10 N·m (40 ± 7 lb ft).
2/6(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00690963
7. Remove the cap to the hydraulic tank. Attach Tooling (A) to the hydraulic tank.
Note: Hook up the air to Tooling (A) in order to create a vacuum in the hydraulic system.
This will minimize the leakage from the hose assemblies.
Note: Replace the O-ring seals that are used in the ends of the hose assemblies.
Illustration 4 g00695023
8. Connect hose assembly (19).
Illustration 5 g00694470
9. Connect hose assembly (13).
10. Install the split flanges, the washers and bolts (15).
11. Connect hose assembly (16).
12. Connect hose assembly (11).
13. Install the split flanges, the washers, and bolts (14).
14. Connect hose assembly (12).
3/6(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 15. Connect hose assembly (10).
16. Connect harness assembly (18).
17. Install the clip, the washer, and bolt (17).
Illustration 6 g00694459
Typical example
18. Connect hose assembly (7) (If Equipped).
19. Install hose assembly (6) (If Equipped).
20. Install brace (8) with washers and bolts (9) (If Equipped).
Illustration 7 g00694353
21. Make sure that the drain valve (5) is closed.
22. Remove Tooling (A) and install the cap to the hydraulic tank.
NOTICE
To avoid system damage, make sure that the hydraulic motor is
properly filled with hydraulic oil before start-up.
4/6(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. 23. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
24. Fill the hydraulic oil tank and the swing drive with clean hydraulic oil to the correct level.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level -
Check" and Operation and Maintenance Manual, "Swing Drive Oil Level - Check" for the
correct filling procedures.
25. Start the engine, and check the operation of the swing drive. Also, check for leaks. Stop the
engine.
26. Obtain a hydraulic oil sample from the main S·O·S port.
Reference: Refer to Operation and Maintenance Manual, "Sampling Interval and Location
of Sampling Valve" for the correct location.
27. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
Reference: Refer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 320C Hydraulic Excavators" for further information.
Illustration 8 g00694245
28. Install the washers and bolts (4) in order to install access cover (3) that is under the main
control valve.
5/6(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 9 g00950370
29. Install the washers and bolts (1) in order to install cover (2).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 23:45:39 UTC+0800 2019
6/6(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GLA
Configuration: 320C, 320C L, 320C LN Excavators GLA00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01972334
Swing Drive - Remove
SMCS - 5459-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B Forcing Screw (20 mm X 100 mm) 2
Start By:
a. Remove the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Remove" in
this manual.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/4(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the area around the swing drive prior to removal.
2. Put identification marks on the swing drive in order to mark the drive's location for
installation purposes.
Note: It may be necessary to remove the drain hose for the swing drive in order to access
the mount bolts in the rear of the drive.
Illustration 1 g00694361
3. Remove bolts (1) and the washers that secure the swing drive to the main frame.
2/4(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g00694371
4. Attach Tooling (A) and a suitable lifting device to swing drive (2), as shown.
5. Remove corks (3) from the threaded holes in the swing drive housing.
Illustration 3 g01023898
6. Install Tooling (B) in each threaded hole in the swing drive housing.
7. Slowly tighten one forcing screw for no more than two turns, and then tighten the other
forcing screw for no more than two turns. At the same time keep tension on the swing drive
with the hoist. Tighten the forcing screws evenly in this manner in order to separate the
swing drive from the main frame.
3/4(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 4 g01023901
8. Remove swing drive (5) from the machine. The weight of swing drive (5) is approximately
190 kg (420 lb).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 23:46:36 UTC+0800 2019
4/4(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GLA
Configuration: 320C, 320C L, 320C LN Excavators GLA00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01916277
Swing Drive - Disassemble
SMCS - 5459-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
5P-5197 Retaining Ring Pliers 1
1U-8759 Tip Set 1
B 1P-0520 Driver Group 1
Start By:
a. Remove the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove" for
the machine that is being serviced.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
1/9(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Illustration 1 g00702449
1. Remove sun gear (1) from carrier assembly (2).
Illustration 2 g00702450
2. Remove spacer (3) from the carrier assembly.
2/9(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 3 g00702451
3. Remove carrier assembly (2) from ring gear (4).
Illustration 4 g00702452
4. Drive roll pin (5) into shaft (6). Remove shaft (6) and the gear assembly from the carrier
assembly.
Illustration 5 g00702456
5. Disassemble the gear assembly, as follows: washer (7), gear (8), bearing (9), and washer
(10). Remove roll pin (5) from shaft (6).
3/9(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. 6. Repeat Step 4 through Step 5 for the remaining gear assemblies.
Illustration 6 g00702457
7. Remove retaining ring (11) from sun gear (12). Remove carrier (13) from the sun gear.
Illustration 7 g00702459
8. Remove retaining ring (14) from the sun gear.
Illustration 8 g00702583
9. Use two people in order to remove ring gear (15) from housing (16). Weight of ring gear
(15) is approximately 29 kg (65 lb).
4/9(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 9 g00702584
10. Remove spacer (17) from carrier assembly (18).
Illustration 10 g00702596
11. Use Tooling (A) to remove retaining ring (19).
Illustration 11 g00702611
12. Remove carrier assembly (18) from the housing.
5/9(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 12 g00702640
13. Drive roll pin (20) into shaft (21). Remove shaft (21) and the gear assembly from the carrier
assembly.
Illustration 13 g00702648
14. Disassemble the gear assembly, as follows: washer (22), bearing (23), gear (24), bearing
(25), and washer (26). Remove roll pin (20) from shaft (21).
15. Repeat Step 13 through Step 14 for the remaining gear assemblies.
Illustration 14 g00702659
6/9(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 16. Remove four bolts (27) from the housing.
Note: Do not remove the other two bolts (27) at this time. These two bolts (27) will be used
to transport the assembly to the press.
Illustration 15 g00703241
Illustration 16 g00702664
17. Remove remaining bolts (27). Use a suitable press in order to remove shaft (28) from the
housing. Remove cage (29) from the housing.
Note: The bearing may come off with the pinion or the bearing may stay in the housing.
7/9(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 17 g00703242
18. Remove O-ring seal (30) from the cage. Remove lip type seals (31) from the cage.
Illustration 18 g00703246
Illustration 19 g00703247
19. Use a suitable press and Tooling (B) in order to remove bearing (34), spacer (33), and
bearing (32) from the housing. Remove alignment pin (35) from the housing.
Illustration 20 g00703249
8/9(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 20. Remove drain valve (36) from the housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 23:47:31 UTC+0800 2019
9/9(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GLA
Configuration: 320C, 320C L, 320C LN Excavators GLA00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i02015036
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B
5P-5197 Retaining Ring Pliers 1
1U-8759 Tip Set 1
C Threaded Guide Stud (M16×2.00×140mm) 2
D 1U-6396 O-Ring Assembly Compound
E 4C-9613 Silicone Sealant
F 5P-3931 Anti-Seize Compound
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use Tooling (D) during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
1/10(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 1 g00703249
1. Install drain valve (36) into the housing.
Illustration 2 g00703242
2. Install O-ring seal (30) into the cage. Install lip type seals (31) into the cage.
Illustration 3 g00703692
3. Install cage (29) onto shaft (28).
2/10(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 4 g00703693
4. Raise the temperature of bearing (32) to 135 °C (275 °F). Install bearing (32) onto shaft
(28).
Illustration 5 g00703694
5. Install spacer (33) onto shaft (28). Install spacer (33) with relief against bearing (32).
Illustration 6 g00703695
6. Raise the temperature of bearing (34) to 135 °C (275 °F). Install bearing (34) onto shaft (28)
against spacer (33).
3/10(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 7 g01041742
7. Place shaft assembly (28) onto a flat surface. Install Tooling (A) and a suitable lifting device
onto housing (16). Apply Tooling (E) to the face of cage (29). Apply Tooling (F) to the
inside diameters of the housing. Raise the temperature of housing (16) to 93 °C (200 °F).
Use a suitable lifting device and lower the housing onto the shaft assembly.
Illustration 8 g00703697
8. Install bolts (27) into the housing. Install alignment pin (35) into the housing.
Illustration 9 g00703698
4/10(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. 9. Assemble the gear assembly, as follows: washer (22), bearing (23), gear (24), bearing (25),
and washer (26).
Illustration 10 g00702640
Illustration 11 g00703700
10. Use a deburring tool in order to remove the metal burr from the openings in the carrier.
Install shaft (21) and the gear assembly into the carrier assembly. Drive roll pin (20) into
shaft (21). Orient the split in roll pin (20) vertically to the carrier. Align the split in the roll
pin to the top or to the bottom. Make a stake mark on each side of the roll pin hole in the
carrier. Each stake mark should be approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from
the outside diameter of the roll pin hole.
11. Repeat Step 9 through Step 10 for the remaining gear assemblies.
5/10(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Illustration 12 g00702611
12. Install carrier assembly (18) into the housing.
Illustration 13 g00702596
13. Use Tooling (B) to install retaining ring (19).
Illustration 14 g00702584
14. Install spacer (17) into carrier assembly (18).
6/10(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 15 g00703699
Illustration 16 g00702583
15. Apply Tooling (E) to the face of housing (16). Install Tooling (C) in order to help align the
housing and the ring gear. Use two people in order to install ring gear (15) onto housing
(16). Weight of ring gear (15) is approximately 29 kg (65 lb).
Illustration 17 g00702459
16. Install retaining ring (14) into the sun gear.
7/10(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 18 g00702457
17. Install carrier (13) into the sun gear. Install retaining ring (11) into sun gear (12).
Illustration 19 g00703707
18. Assemble the gear assembly, as follows: washer (7), gear (8), bearing (9), and washer (10).
Illustration 20 g00702452
8/10(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
30. Illustration 21 g00703700
19. Use a deburring tool in order to remove the metal burr from the openings in the carrier.
Install shaft (6) and the gear assembly into the carrier assembly. Drive roll pin (5) into shaft
(6). Orient the split in roll pin (5) vertically to the carrier. Align the split in the roll pin to the
top or to the bottom. Make a stake mark on each side of the roll pin hole in the carrier. Each
stake mark should be approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside
diameter of the roll pin hole.
20. Repeat Step 18 through Step 19 for the remaining gear assemblies.
Illustration 22 g00702451
21. Install carrier assembly (2) into ring gear (4).
9/10(W)
w
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...