This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, inserting pins using specialized tools, setting linkage brackets, and synchronizing the unit injectors. Proper torque specifications and tool references are included to ensure correct installation.
Caterpillar cat 320 a excavator (prefix 3 rk) service repair manual (3rk00001...fujsekfsmemm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a 320-A excavator engine. The removal process involves disconnecting tubes, removing clips and pins connecting the governor. The installation involves cleaning and lubricating seals, installing the governor with new seals and pins, and connecting it to the control linkage. Special tools are required for tasks like inserting pins. References are provided for additional information on governors, linkages and engine components.
Caterpillar cat 320 l excavator (prefix 4 bk) service repair manual (4bk00001...ujfjjskkekmem
This document provides instructions for removing and installing a governor from a 320 L EXCAVATOR engine. The removal procedure involves disconnecting control cables, removing clips and tubes, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, placing the governor back in position, reconnecting control links and tubes, and adjusting settings. Precise use of various specialty tools is required to properly complete the process.
Caterpillar cat 320 track type excavator (prefix 1 tl) service repair manual ...ufuusefjjsekkm
This document provides instructions for removing and installing a governor on a Caterpillar 320L excavator engine. It begins by listing the required tools. The removal procedure involves 11 steps that include disconnecting cables, removing clips and pins, and taking out bolts and seals. The installation procedure reverses these steps, applying lubricant to new seals and ensuring proper pin and clip installation. References are provided for additional information on governor calibration and inspection.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
This document provides instructions for removing and installing a governor and fuel injection control linkage on an excavator engine. The removal procedure involves disconnecting cables, removing clips and pins, and taking off bolts. The installation involves applying lubricant to seals, placing parts in position, installing clips, pins and bolts using various specialized tools, and setting adjustments. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...fjskekfseik
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin to detach the governor from the linkage. Installation requires reattaching these components using special tools, adjusting brackets, and compressing injector springs during assembly. References are provided for additional maintenance information.
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...fjskekfseik
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin to detach the governor from the linkage. Installation requires reattaching these components using tools, adjusting brackets, and compressing injector springs during installation. References are provided for additional information on inspection and synchronization procedures.
Caterpillar cat 320 s excavator (prefix 3 xk) service repair manual (3xk00822...fjskekfseik
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 320 a excavator (prefix 3 rk) service repair manual (3rk00001...fujsekfsmemm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a 320-A excavator engine. The removal process involves disconnecting tubes, removing clips and pins connecting the governor. The installation involves cleaning and lubricating seals, installing the governor with new seals and pins, and connecting it to the control linkage. Special tools are required for tasks like inserting pins. References are provided for additional information on governors, linkages and engine components.
Caterpillar cat 320 l excavator (prefix 4 bk) service repair manual (4bk00001...ujfjjskkekmem
This document provides instructions for removing and installing a governor from a 320 L EXCAVATOR engine. The removal procedure involves disconnecting control cables, removing clips and tubes, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, placing the governor back in position, reconnecting control links and tubes, and adjusting settings. Precise use of various specialty tools is required to properly complete the process.
Caterpillar cat 320 track type excavator (prefix 1 tl) service repair manual ...ufuusefjjsekkm
This document provides instructions for removing and installing a governor on a Caterpillar 320L excavator engine. It begins by listing the required tools. The removal procedure involves 11 steps that include disconnecting cables, removing clips and pins, and taking out bolts and seals. The installation procedure reverses these steps, applying lubricant to new seals and ensuring proper pin and clip installation. References are provided for additional information on governor calibration and inspection.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
This document provides instructions for removing and installing a governor and fuel injection control linkage on an excavator engine. The removal procedure involves disconnecting cables, removing clips and pins, and taking off bolts. The installation involves applying lubricant to seals, placing parts in position, installing clips, pins and bolts using various specialized tools, and setting adjustments. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...fjskekfseik
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin to detach the governor from the linkage. Installation requires reattaching these components using special tools, adjusting brackets, and compressing injector springs during assembly. References are provided for additional maintenance information.
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...fjskekfseik
This document provides instructions for removing and installing a fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves taking out the rocker shaft and pushrods, then removing clips and a clevis pin to detach the governor from the linkage. Installation requires reattaching these components using tools, adjusting brackets, and compressing injector springs during installation. References are provided for additional information on inspection and synchronization procedures.
Caterpillar cat 320 s excavator (prefix 3 xk) service repair manual (3xk00822...fjskekfseik
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
New holland engine 8.3 l 6 cylinder, 24 valve cnh engine with high pressure c...ufusjfjkkekm
The document is a repair manual that provides information on servicing New Holland 8.3 & 9.0L 6 cylinder engines with high pressure common rail fuel systems. It includes sections on the engine, fuel and injection system, air intake system, exhaust system, cooling system, lubrication system, and starting system. The manual uses an integrated coding environment to organize information and point to specific sections, chapters, and sub-chapters. It provides exploded views, specifications, torque values, service limits, inspection procedures, and special tool requirements for servicing engine components.
This document provides part numbers and descriptions for engine components of a Massey Ferguson 6497 Tier 3 tractor. It includes two pages of detailed component lists and part numbers for the engine, cylinder block, timing gear housing, crankshaft, piston, connecting rods, and valve mechanism. The lists contain over 50 individual engine parts and components.
Massey ferguson 6480 tractor (tier 3 sisu engine) service parts catalogue man...ufusjfjkkekm
This document provides parts information for a Massey Ferguson 6480 tractor with a Tier 3 Sisu engine. It includes 35 items with part numbers, quantities, descriptions, and additional comments or footnotes. The items are various engine parts such as the cylinder block, timing gear housing, crankshaft, pistons, and main bearings. Footnotes provide additional part number variants or specifications depending on the tractor serial number or country.
Kubota v3800 tie4 diesel engine service repair manualufusjfjkkekm
The document provides specifications for 6 diesel engine models: V3800-CR-TE4, V3800-CR-TE4C, V3800-CR-TIE4, V3800-CR-TIE4C, V3800-TIE4, and V3800-TIE4C. The specifications include information such as the number of cylinders, displacement, power output, lubrication system, cooling system, dimensions, and fuel and oil requirements. The engines are vertical, water-cooled, 4-cycle direct injection diesel engines with a bore of 100mm and stroke of 120mm for a total displacement of 3769cm3.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 7yb) service ...ufusjfjkkekm
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8L track-type tractor powered by a 3408 engine. The removal procedure involves using various tools to disassemble the rear gear group components and remove the flywheel. The installation procedure describes reassembling the rear gear group components and installing the flywheel using press tools and guide bolts. Precautions are given to keep parts clean and lubricated during assembly to prevent wear.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 7yb) service ...ufusjfjkkekm
The document provides instructions for disassembling and assembling a unit injector hydraulic pump. It describes 17 steps for disassembly, which include removing various parts like the pressure compensator valve, manifold, valve block, and bearings. It then describes 24 steps for assembly, covering the installation of gaskets, seals, springs, and other parts in the reverse order of disassembly. Precautions are given to keep parts clean and prevent dirt entry into the fuel system. Various tools are listed that are required for the procedures.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...ufusjfjkkekm
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar 416F backhoe loader. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning and inspecting the oil cooler, installing a new gasket, and securing the cooler in place with bolts and spacers. Tools required include wrenches and containers for draining fluids. Safety precautions are provided to contain fluids and follow cleanliness standards when working on engine components.
Caterpillar cat 416 series ii backhoe loader (prefix 5 pc) service repair man...ufusjfjkkekm
This document provides instructions for servicing the rear axle and differential of a 416 Series II Backhoe Loader. It describes how to remove and disassemble the rear axle group and differential. Key steps include draining fluids, removing mounting hardware, and using specialty tools to press components from housings. Reassembly is described in reverse order, noting proper torque specifications and pre-load adjustments as needed.
Caterpillar cat 415 f2 il backhoe loader (prefix pf4) service repair manual (...ufusjfjkkekm
This document provides instructions for disassembling the transmission of a 415F2 IL Backhoe Loader. It describes removing various components such as the torque converter, shafts, gears, bearings, seals and other parts. Detailed illustrations and cautions are provided to safely compress springs and remove press-fit components using the appropriate tools. The multi-step process is described for disassembling the direct drive, front output shaft, rear output shaft, direct drive shaft, and reverse shaft assemblies of the transmission.
Caterpillar cat 322 l excavator (prefix 8cl) service repair manual (8cl00001 ...ufusjfjkkekm
This document provides instructions for servicing the air conditioning system on a Caterpillar 322L excavator. It describes safety precautions when working with refrigerant due to risks of frostbite and inhalation. The procedures cover preparing the machine, recovering refrigerant, removing and installing various components like lines, the compressor, and preparing the system for charging. Precautions are outlined to keep the system clean and only use new refrigerant and oil to avoid contamination.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect tubes, pins, and clips connecting the governor to the engine. The fuel injection control linkage is then removed by taking out bolts. The installation procedure details applying lubricant to seals before reinstalling components and reconnecting everything using the special tools. Proper torque specifications are provided for the bolts.
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...ufusjfjkkekm
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, inserting pins using specialized tools, setting linkage brackets, and synchronizing the unit injectors. Specialized tools and additional reference manuals are required to properly perform the work.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...ufusjfjkkekm
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, then reversing the removal steps and using special tools to correctly position and secure the governor and linkage. Proper adjustment of settings is also described.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, then reversing the removal steps and using various tools to properly position, connect and adjust the governor and linkage. Proper torque specifications are provided for bolts. References are made to other documents for additional information.
Case ih wd1904 tier 3 self propelled windrower service repair manual [ -yfg67...ufusjfjkkekm
This document provides service information for WD1904 and WD2304 self-propelled windrowers, including specifications for the Tier 3 engine that powers both models. The 6.7L, 6-cylinder turbocharged diesel engine produces 142 kW of power at 2200 RPM and peak torque of 830N·m at 1600 RPM for the WD1904 and 961N·m at 1600 RPM for the WD2304. The manual contains sections covering maintenance and repair of the engine and related components, as well as other vehicle systems like hydraulics, steering, and electrical systems.
Case ih axial flow 9240 tier 2 combine service repair manualufusjfjkkekm
This service manual provides information for servicing the engines used in Axial-Flow 7240, 8240, and 9240 combines. It details removing and installing various engine components like the crankcase, air intake and exhaust systems, fuel lines, cooling systems, and emissions equipment. Safety precautions are provided to avoid injury when working on the engine.
Case ih 6130 combine service repair manualufusjfjkkekm
This document is a service manual for CNH industrial combine harvesters models 5130, 6130, and 7130. It contains over 100 sections covering all major systems of the combines like the engine, transmission, hydraulics, electrical, attachments, and safety information. The manual provides part numbers, diagrams, and instructions for maintenance and repair of components. Safety rules regarding personal protective equipment, spill prevention, and battery recycling are provided at the beginning.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
New holland engine 8.3 l 6 cylinder, 24 valve cnh engine with high pressure c...ufusjfjkkekm
The document is a repair manual that provides information on servicing New Holland 8.3 & 9.0L 6 cylinder engines with high pressure common rail fuel systems. It includes sections on the engine, fuel and injection system, air intake system, exhaust system, cooling system, lubrication system, and starting system. The manual uses an integrated coding environment to organize information and point to specific sections, chapters, and sub-chapters. It provides exploded views, specifications, torque values, service limits, inspection procedures, and special tool requirements for servicing engine components.
This document provides part numbers and descriptions for engine components of a Massey Ferguson 6497 Tier 3 tractor. It includes two pages of detailed component lists and part numbers for the engine, cylinder block, timing gear housing, crankshaft, piston, connecting rods, and valve mechanism. The lists contain over 50 individual engine parts and components.
Massey ferguson 6480 tractor (tier 3 sisu engine) service parts catalogue man...ufusjfjkkekm
This document provides parts information for a Massey Ferguson 6480 tractor with a Tier 3 Sisu engine. It includes 35 items with part numbers, quantities, descriptions, and additional comments or footnotes. The items are various engine parts such as the cylinder block, timing gear housing, crankshaft, pistons, and main bearings. Footnotes provide additional part number variants or specifications depending on the tractor serial number or country.
Kubota v3800 tie4 diesel engine service repair manualufusjfjkkekm
The document provides specifications for 6 diesel engine models: V3800-CR-TE4, V3800-CR-TE4C, V3800-CR-TIE4, V3800-CR-TIE4C, V3800-TIE4, and V3800-TIE4C. The specifications include information such as the number of cylinders, displacement, power output, lubrication system, cooling system, dimensions, and fuel and oil requirements. The engines are vertical, water-cooled, 4-cycle direct injection diesel engines with a bore of 100mm and stroke of 120mm for a total displacement of 3769cm3.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 7yb) service ...ufusjfjkkekm
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8L track-type tractor powered by a 3408 engine. The removal procedure involves using various tools to disassemble the rear gear group components and remove the flywheel. The installation procedure describes reassembling the rear gear group components and installing the flywheel using press tools and guide bolts. Precautions are given to keep parts clean and lubricated during assembly to prevent wear.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 7yb) service ...ufusjfjkkekm
The document provides instructions for disassembling and assembling a unit injector hydraulic pump. It describes 17 steps for disassembly, which include removing various parts like the pressure compensator valve, manifold, valve block, and bearings. It then describes 24 steps for assembly, covering the installation of gaskets, seals, springs, and other parts in the reverse order of disassembly. Precautions are given to keep parts clean and prevent dirt entry into the fuel system. Various tools are listed that are required for the procedures.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...ufusjfjkkekm
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar 416F backhoe loader. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning and inspecting the oil cooler, installing a new gasket, and securing the cooler in place with bolts and spacers. Tools required include wrenches and containers for draining fluids. Safety precautions are provided to contain fluids and follow cleanliness standards when working on engine components.
Caterpillar cat 416 series ii backhoe loader (prefix 5 pc) service repair man...ufusjfjkkekm
This document provides instructions for servicing the rear axle and differential of a 416 Series II Backhoe Loader. It describes how to remove and disassemble the rear axle group and differential. Key steps include draining fluids, removing mounting hardware, and using specialty tools to press components from housings. Reassembly is described in reverse order, noting proper torque specifications and pre-load adjustments as needed.
Caterpillar cat 415 f2 il backhoe loader (prefix pf4) service repair manual (...ufusjfjkkekm
This document provides instructions for disassembling the transmission of a 415F2 IL Backhoe Loader. It describes removing various components such as the torque converter, shafts, gears, bearings, seals and other parts. Detailed illustrations and cautions are provided to safely compress springs and remove press-fit components using the appropriate tools. The multi-step process is described for disassembling the direct drive, front output shaft, rear output shaft, direct drive shaft, and reverse shaft assemblies of the transmission.
Caterpillar cat 322 l excavator (prefix 8cl) service repair manual (8cl00001 ...ufusjfjkkekm
This document provides instructions for servicing the air conditioning system on a Caterpillar 322L excavator. It describes safety precautions when working with refrigerant due to risks of frostbite and inhalation. The procedures cover preparing the machine, recovering refrigerant, removing and installing various components like lines, the compressor, and preparing the system for charging. Precautions are outlined to keep the system clean and only use new refrigerant and oil to avoid contamination.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect tubes, pins, and clips connecting the governor to the engine. The fuel injection control linkage is then removed by taking out bolts. The installation procedure details applying lubricant to seals before reinstalling components and reconnecting everything using the special tools. Proper torque specifications are provided for the bolts.
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...ufusjfjkkekm
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, inserting pins using specialized tools, setting linkage brackets, and synchronizing the unit injectors. Specialized tools and additional reference manuals are required to properly perform the work.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...ufusjfjkkekm
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, then reversing the removal steps and using special tools to correctly position and secure the governor and linkage. Proper adjustment of settings is also described.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, then reversing the removal steps and using various tools to properly position, connect and adjust the governor and linkage. Proper torque specifications are provided for bolts. References are made to other documents for additional information.
Case ih wd1904 tier 3 self propelled windrower service repair manual [ -yfg67...ufusjfjkkekm
This document provides service information for WD1904 and WD2304 self-propelled windrowers, including specifications for the Tier 3 engine that powers both models. The 6.7L, 6-cylinder turbocharged diesel engine produces 142 kW of power at 2200 RPM and peak torque of 830N·m at 1600 RPM for the WD1904 and 961N·m at 1600 RPM for the WD2304. The manual contains sections covering maintenance and repair of the engine and related components, as well as other vehicle systems like hydraulics, steering, and electrical systems.
Case ih axial flow 9240 tier 2 combine service repair manualufusjfjkkekm
This service manual provides information for servicing the engines used in Axial-Flow 7240, 8240, and 9240 combines. It details removing and installing various engine components like the crankcase, air intake and exhaust systems, fuel lines, cooling systems, and emissions equipment. Safety precautions are provided to avoid injury when working on the engine.
Case ih 6130 combine service repair manualufusjfjkkekm
This document is a service manual for CNH industrial combine harvesters models 5130, 6130, and 7130. It contains over 100 sections covering all major systems of the combines like the engine, transmission, hydraulics, electrical, attachments, and safety information. The manual provides part numbers, diagrams, and instructions for maintenance and repair of components. Safety rules regarding personal protective equipment, spill prevention, and battery recycling are provided at the beginning.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
Illustration 2 g00613071
3. Remove clip (4).
2/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Illustration 3 g00655975
4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 4 g00613149
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
3/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Illustration 5 g00613563
6. Remove bolts (7) and the washers that hold the governor in position.
Illustration 6 g00673182
7. Remove the governor from the engine.
Illustration 7 g00673180
8. Remove O-ring seal (3) on the governor.
Illustration 8 g00672742
4/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. 9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
Illustration 9 g00672733
10. Remove O-ring seal (2) on the tube assembly (5).
Illustration 10 g00673178
11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Dec 18 08:40:28 UTC+0800 2019
5/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928419
Governor - Install
SMCS - 1264-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
(1)
This tool is part of the 128-8822 Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
1/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 1 g00673178
1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head.
Illustration 2 g00672733
2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly
(5).
Illustration 3 g00672742
3. Install the O-ring seal and tube assembly (5) in the cylinder head.
2/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 4 g00673180
4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor.
Illustration 5 g00673182
5. Place the governor in position on the engine.
Illustration 6 g00613563
6. Install the washers and bolts (7) that hold the governor in place.
3/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 7 g00672755
7. Install clevis pin (6) in Tooling (B).
Illustration 8 g00672752
8. Use Tooling (B) to install clevis pin (6) and the clip.
9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118.
4/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Illustration 9 g00655975
10. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 10 g00613071
11. Install clip (4).
Illustration 11 g00613041
12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
13. Install the governor control cable.
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Dec 18 08:41:23 UTC+0800 2019
5/5(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928445
Fuel Injection Control Linkage - Remove
SMCS - 1298-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 1 g00613071
1. Remove clip (4). Clip (4) is located between the governor and the cylinder head.
Illustration 2 g00655975
2. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 3 g00613149
2/3(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. 3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects
the governor to the control lever of the fuel injection control linkage.
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
Illustration 4 g00630566
4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects
the fuel injection control linkage (2) to the governor.
Note: For information on the inspection procedure for control lever (3), refer to Special
Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection
Control Linkage and the 4P-9048 Fuel Injection Control Linkage".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Dec 18 08:42:19 UTC+0800 2019
3/3(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F
Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928573
Fuel Injection Control Linkage - Install
SMCS - 1298-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
C 1U-6675 Spring Compressor(1)
6
D 128-8822 Fuel System and Governor Tool Gp 1
(1)
This tool is part of the 128-8822 Governor Tool Group.
1/4(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Illustration 1 g00661331
Note: For information on the inspection procedure for control lever (3), refer to Special Instruction,
REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P
-9048 Fuel Injection Control Linkage".
1. Loosen setscrews (4) on each bracket.
2. Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the
bolts.
3. Tighten bracket (A) and (D) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
4. Tighten brackets (B) and (C) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
5. Position brackets (B) and (C) in order to allow free rotation of the fuel control rod.
6. Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of
3.5 ± 0.2 N·m (31 ± 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates
freely.
7. The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever
(3).
Illustration 2 g00750163
8. Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control
linkage (2).
Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector -
Install".
2/4(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. 9. Install Tooling (C) on the unit injectors and compress the springs.
Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using
the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
Illustration 3 g00672755
10. Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor.
Illustration 4 g00672752
11. Use Tooling (B) to install clevis pin (6) and the clip.
12. Use Tooling (D) to set the unit injector synchronization.
Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the
128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
13. Remove Tooling (C) from the unit injectors.
3/4(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Illustration 5 g00655975
14. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 6 g00613071
15. Install clip (4).
End By:
a. Install the rocker arm assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Dec 18 08:43:15 UTC+0800 2019
4/4(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 3XK
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i05919358
Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0302 Bar 1
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/3(W)w
2019/12/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...