This document provides instructions for disassembling and installing the engine oil pump and water pump on a Caterpillar 320C excavator. Key steps include using tools to remove the oil pump gears and housing cover, installing new seals, and heating components to aid removal and installation. Safety notices warn of ensuring clean parts and containing fluids during disassembly.
Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk000...ujfjjsjekkmsmd
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator powered by a 3066 engine. It describes removing the front housing, cover, gears, seals, and spindle. It then describes installing new seals, heating components, and reinstalling gears, cover, and front housing. Removal and installation of the water pump is also described.
Caterpillar cat 966 h wheel loader (prefix bs6) service repair manual (bs6000...fudjsjfekskkem
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1) Using a valve spring compressor tool to remove valve locks, springs, rotators, and valves.
2) Lubricating and installing new valves, seals, springs and locks using the compressor tool.
3) To begin, the cylinder head must be removed and cleaned of contaminants before starting the valve job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk000...ujfjjsjekkmsmd
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator powered by a 3066 engine. It describes removing the front housing, cover, gears, seals, and spindle. It then describes installing new seals, heating components, and reinstalling gears, cover, and front housing. Removal and installation of the water pump is also described.
Caterpillar cat 966 h wheel loader (prefix bs6) service repair manual (bs6000...fudjsjfekskkem
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1) Using a valve spring compressor tool to remove valve locks, springs, rotators, and valves.
2) Lubricating and installing new valves, seals, springs and locks using the compressor tool.
3) To begin, the cylinder head must be removed and cleaned of contaminants before starting the valve job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. The removal procedure involves taking off the front housing, cover, gears, seals and spindle. The installation procedure specifies heating some components, using tools to press in seals and gears, and ensuring proper alignment and torque of fasteners. Proper cleaning and containment of fluids is emphasized.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. It describes:
1. Removing the front housing, cover, gears, seals, and spindle to access the oil pump.
2. Using tools like a puller and driver to remove specific components.
3. Installing the spindle, gears, seals, cover, and front housing, ensuring clean surfaces and applying the correct torque.
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 320C LN excavator. It outlines 10 steps to remove the pump, including removing the front housing, cover, gears, seals and spindle. It then outlines 8 steps to install the pump, including heating components, installing seals, gears and the cover. Safety notices are provided regarding keeping components clean and containing fluids.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It includes 6 steps to remove the oil pump, requiring various tools. The oil pump installation has 6 steps as well, including heating components to aid installation. The water pump removal requires 3 steps including removing bolts and the pump. The water pump disassembly has 6 steps after heating the pump. Reassembly of the water pump lists 7 steps including installing seals and bearings using press tools.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It describes in step-by-step detail how to disassemble, remove, and install each component while maintaining cleanliness and containing fluids. Tools required are listed for each procedure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to clean and lubricate the parts before reinstalling them in reverse order. Proper use of tooling is emphasized to safely compress springs during the process.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...ze6074xunong
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. Additional documents cover removing and installing the assembled auxiliary pump drive group and performing maintenance on other excavator systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, bearings and seals.
2. The assembly instructions then guide rebuilding the pump drive group, including pressing in new bearings, installing seals and covers, and reassembling the shafts and gears.
3. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...f8usejkdmmd8i
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekdkmd8ddjd
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. The overall purpose is to repair or replace internal components while preventing contamination of the hydraulic system.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...f8ujkskdmdm
The document provides step-by-step instructions to disassemble and assemble the auxiliary pump drive group of an excavator. It details removing covers, shafts, gears, seals, and bearings during disassembly. The assembly section instructs lowering bearing temperatures and installing components in reverse order while applying sealant. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...f8ujkskdmdm
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then detail how to install the bearings at the proper temperatures and reassemble the components in reverse order.
3. Proper cleaning and replacement of seals is emphasized to prevent contamination of hydraulic systems.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekdkmd8ddjd
This document provides instructions for disassembling and assembling the auxiliary pump drive of an excavator. It begins with safety notices and a list of required tools. The disassembly steps include removing alignment pins, bolts, covers, seals, shafts, gears, and bearings from the pump drive body. The assembly steps list installing these components in reverse order, noting the importance of cleanliness and replacing seals. Torque and heating specifications are provided for installing bearings. The process is completed by reinstalling the auxiliary pump drive.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...zoat27912076
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Doosan mega 160 wheeled loader parts catalogue manualfjjskekfsem
The document provides a parts list and exploded diagram of a cylinder head assembly. It lists over 100 individual part numbers, descriptions, quantities, serial numbers and replacement part information. The cylinder head assembly drawing shows the main components which include the cylinder head, valves, guides, seats, plugs and related mounting hardware.
Doosan e85 compact excavator parts catalogue manualfjjskekfsem
This document contains a parts list and descriptions for a cylinder block assembly. It lists 31 individual parts that make up the cylinder block including the block itself, plugs, bolts, bushes, pins, and other components. It provides the part number, description, quantity, and other identifying information for each part.
More Related Content
Similar to Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk00001 and up)
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. The removal procedure involves taking off the front housing, cover, gears, seals and spindle. The installation procedure specifies heating some components, using tools to press in seals and gears, and ensuring proper alignment and torque of fasteners. Proper cleaning and containment of fluids is emphasized.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. It describes:
1. Removing the front housing, cover, gears, seals, and spindle to access the oil pump.
2. Using tools like a puller and driver to remove specific components.
3. Installing the spindle, gears, seals, cover, and front housing, ensuring clean surfaces and applying the correct torque.
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 320C LN excavator. It outlines 10 steps to remove the pump, including removing the front housing, cover, gears, seals and spindle. It then outlines 8 steps to install the pump, including heating components, installing seals, gears and the cover. Safety notices are provided regarding keeping components clean and containing fluids.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It includes 6 steps to remove the oil pump, requiring various tools. The oil pump installation has 6 steps as well, including heating components to aid installation. The water pump removal requires 3 steps including removing bolts and the pump. The water pump disassembly has 6 steps after heating the pump. Reassembly of the water pump lists 7 steps including installing seals and bearings using press tools.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It describes in step-by-step detail how to disassemble, remove, and install each component while maintaining cleanliness and containing fluids. Tools required are listed for each procedure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to clean and lubricate the parts before reinstalling them in reverse order. Proper use of tooling is emphasized to safely compress springs during the process.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...ze6074xunong
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. Additional documents cover removing and installing the assembled auxiliary pump drive group and performing maintenance on other excavator systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, bearings and seals.
2. The assembly instructions then guide rebuilding the pump drive group, including pressing in new bearings, installing seals and covers, and reassembling the shafts and gears.
3. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...f8usejkdmmd8i
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekdkmd8ddjd
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. The overall purpose is to repair or replace internal components while preventing contamination of the hydraulic system.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...f8ujkskdmdm
The document provides step-by-step instructions to disassemble and assemble the auxiliary pump drive group of an excavator. It details removing covers, shafts, gears, seals, and bearings during disassembly. The assembly section instructs lowering bearing temperatures and installing components in reverse order while applying sealant. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...f8ujkskdmdm
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then detail how to install the bearings at the proper temperatures and reassemble the components in reverse order.
3. Proper cleaning and replacement of seals is emphasized to prevent contamination of hydraulic systems.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekdkmd8ddjd
This document provides instructions for disassembling and assembling the auxiliary pump drive of an excavator. It begins with safety notices and a list of required tools. The disassembly steps include removing alignment pins, bolts, covers, seals, shafts, gears, and bearings from the pump drive body. The assembly steps list installing these components in reverse order, noting the importance of cleanliness and replacing seals. Torque and heating specifications are provided for installing bearings. The process is completed by reinstalling the auxiliary pump drive.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...zoat27912076
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Similar to Caterpillar cat 320 c ln excavator (prefix axk) service repair manual (axk00001 and up) (20)
Doosan mega 160 wheeled loader parts catalogue manualfjjskekfsem
The document provides a parts list and exploded diagram of a cylinder head assembly. It lists over 100 individual part numbers, descriptions, quantities, serial numbers and replacement part information. The cylinder head assembly drawing shows the main components which include the cylinder head, valves, guides, seats, plugs and related mounting hardware.
Doosan e85 compact excavator parts catalogue manualfjjskekfsem
This document contains a parts list and descriptions for a cylinder block assembly. It lists 31 individual parts that make up the cylinder block including the block itself, plugs, bolts, bushes, pins, and other components. It provides the part number, description, quantity, and other identifying information for each part.
Doosan e80 compact excavator parts catalogue manualfjjskekfsem
This document contains parts lists and diagrams for various components of an engine, including the cylinder block, gear housing, flywheel housing, oil pan, cylinder head, suction manifold, exhaust manifold, camshaft, crankshaft, pistons, and lubrication oil system. It lists part numbers, descriptions, quantities, and other identifying information for over 50 individual parts across 18 figures.
Doosan e63 compact excavator parts catalogue manualfjjskekfsem
This document provides a parts list and descriptions for various components of an engine, including:
- The cylinder block assembly and related plugs and bolts.
- The gear housing, oil pump, seals, bolts, and covers.
- The flywheel housing, oil pan, seals, and bolts.
- The cylinder head, valves, springs, seals, bolts, and related components.
- The intake manifold, sensors, bolts, and throttle body.
- The exhaust manifold, sensors, bolts, pipes, and EGR components.
- The DPF muffler, sensors, case, bolts, pipes, and brackets.
-
Doosan e55 w compact excavator parts catalogue manualfjjskekfsem
This document contains figures and part numbers for various engine components of an E55W engine, including the cylinder block, gear housing, flywheel housing, cylinder head, intake manifold, exhaust manifold, cam shaft, crank shaft, piston, lubrication oil system, and cooling water system. It provides exploded diagrams of the components with corresponding part numbers, descriptions, and quantities for each part.
Doosan dl420 a wheeled loader parts catalogue manualfjjskekfsem
This document contains parts lists and diagrams for various components of a diesel engine. It includes lists of parts, part numbers, descriptions and quantities for items like the cylinder block, timing gear case, flywheel housing, driving system, cylinder head, cylinder head cover, and timing system. Serial numbers are provided for some replaceable parts.
Doosan dl200 tc wheeled loader parts catalogue manualfjjskekfsem
This document provides a parts list and diagrams for the cylinder head and related components of a diesel engine. It includes images and lists of parts with descriptions, part numbers, quantities, serial numbers and replacement part information. The list contains over 80 individual part items or assemblies that make up the cylinder head, valves, springs, guides, cover, gaskets and related hardware.
Doosan 460 plus tier 3 skid steer loader parts catalogue manualfjjskekfsem
This document contains parts lists and diagrams for various components of a diesel engine, including the cylinder block, gear housing, flywheel housing, cylinder head, intake manifold, exhaust manifold, cam shaft, crank shaft, piston, lubrication oil system, and cooling water system. It provides part numbers, descriptions, quantities, and other identifying information for over 50 individual parts across these various engine systems.
Daewoo doosan solar 500 lc v (500lcv) crawler excavator parts catalogue manualfjjskekfsem
The document provides a parts list for a muffler assembly, listing part numbers, descriptions, and quantities. It details different muffler sub-assembly and muffler part numbers used over different serial number ranges. Replacement part numbers are also provided where applicable.
Daewoo doosan solar 470 lc v crawler excavator parts catalogue manualfjjskekfsem
This document provides a parts list for a main frame assembly. It includes 3 frames, 2 weights, bolts, washers, brackets, and other minor parts. Serial numbers and replacement part numbers are provided for some items. A second similar document then lists parts for an engine mounting assembly, including an engine, radiator, hoses, mounts, brackets, and fasteners.
Daewoo doosan solar 450 lc v crawler excavator parts catalogue manualfjjskekfsem
The document provides a parts list and descriptions for a cylinder block assembly. It lists over 150 individual parts that make up the cylinder block, including the cylinder block itself, bearing caps, bolts, plugs, seals, switches, pipes, flanges, nozzles, brackets, and other miscellaneous parts. It provides the part numbers, descriptions, and quantities for each part.
New holland l228 tier 4 b (final) skid steer loader service repair manual [nf...fjjskekfsem
This document is a service manual for Tier 4B (final) and Stage IV 200 Series Skid Steer Loaders and Compact Track Loaders, including the L221, L228, C227, and C232 models. It contains sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. Safety rules regarding ecology and the environment are also included. The manual provides repair and maintenance instructions to be carried out by qualified dealership personnel using the specified tools and procedures.
New holland cr10.90 combine harvesters service repair manualfjjskekfsem
This document is a service manual for CNH Industrial combine harvesters and covers models CX7.80 through CR10.90. It contains over 200 sections on the various systems of the combines, including the engine, transmission, hydraulic systems, electrical systems, attachments and more. The manual provides repair and maintenance information to technicians working on these agricultural machines.
New holland cx6080 tier 3 combine harvester service repair manualfjjskekfsem
This document is a service manual for CX5000 and CX6000 series machines. It contains sections on hydraulic, pneumatic, electrical and electronic systems, engines and emissions control, transmissions, axles, brakes, steering, frames, cabs, user platforms, environmental controls, frame positioning, tool positioning, lifting, leveling, crop processing, feeding, threshing, separating, cleaning, storing, unloading and fault codes. The manual provides technical data, functional descriptions, diagnostics and service procedures for components and systems.
New holland cr9.90 combine harvesters service repair manualfjjskekfsem
This document is a service manual for various combine harvester models from CNH Industrial. It contains an overview of the components covered in the manual, including the engine, transmissions, axles, brakes, hydraulics, steering, tracks, climate control, and electrical systems. The manual is organized by component group and provides part numbers to identify replacement parts.
New holland cx6080 cx6090 tier 4 combine harvester service repair manualfjjskekfsem
This document is a service manual for CX5000 and CX6000 series machines. It contains sections on hydraulic, pneumatic, electrical and electronic systems, engines and emissions control, transmissions, axles, brakes, steering, frames, cabs, user platforms, environmental controls, frame positioning, tool positioning, lifting, leveling, crop processing, feeding, threshing, separating, cleaning, storing, unloading and fault codes. The manual provides technical data, functional descriptions, diagnostics and service procedures for components and systems.
New holland cx7.80 combine harvesters service repair manualfjjskekfsem
This document is a service manual for CNH Industrial combine harvesters and covers models CX7.80 through CR10.90. It contains over 200 sections organized by technical system covering the engine, transmission, hydraulics, electrical systems, attachments and more. Safety information is provided at the beginning regarding accident prevention and fluid power system requirements.
New holland cr9090 elevation combine harvesters service repair manualfjjskekfsem
The hydraulic system uses a variable displacement pump to power the work functions and steering. Oil is distributed through the main frame and straw elevator stack valves to cylinders and motors. It returns through filters to the pump and reservoir shared with the hydrostatic system. The pump receives charge pressure from the hydrostatic return oil to operate without a separate charge pump.
New holland c227 stage iv compact track loader service repair manual [ndm4718...fjjskekfsem
This document is a service manual for Tier 4B (final) and Stage IV 200 Series Skid Steer Loaders and Compact Track Loaders, including the L221, L228, C227, and C232 models. It contains sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. Safety rules regarding ecology and the environment are also included. The manual provides repair and maintenance instructions to be carried out by qualified dealership personnel using the specified tools and procedures.
Caterpillar cat 903 d compact wheel loader (prefix mzy) service repair manual...fjjskekfsem
This service manual document provides instructions for removing and installing various components on a 903D Compact Wheel Loader, including:
1) The steering frame lock, which must be connected before working on the machine to prevent frame movement.
2) The hydraulic tank, which requires draining fluid and removing numerous hoses, fittings and bolts.
3) The joystick control and mounting, which is removed by disconnecting cables and harnesses after opening cab doors and covers.
4) The steering cylinder, which is removed after relieving pressure and disconnecting hoses by removing pins and clamps.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146335
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolt (1) from the cover (2) .
2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not
shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged.
Illustration 2 g00607770
2/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
Illustration 3 g00607857
4. Position the front housing on a work bench in order to remove the oil pump gear from the
rear of the housing.
5. Use Tool (A) to remove oil pump gear (6) from the front housing.
Illustration 4 g00607885
6. Position the front housing on a work bench in order to remove the drive gear from the front
of the housing.
7. Remove drive gear (7) from the front housing.
3/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g00607947
8. Use Tool (B) to remove front oil seal (8) (not shown) from the front housing.
Illustration 6 g00607955
Note: Illustration 6 does not show that the front seal (8) is removed.
9. Remove set screw (9) from the front housing.
Illustration 7 g00607962
4/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 8 g00607966
Note: Illustration 7 does not show that the front seal (8) is removed.
10. Remove spindle (10) and idler gear (11) as an assembly. Push on the gear with a hardwood
bar (12) through the mounting hole for the front seal. Rotate the gear while the gear is
pushed.
Note: Use care not to damage the pump idler gear and the crankshaft gear.
Note: Replace the drive gear and the driven gear as an assembly.
Note: Do not attempt to reuse the oil pump gear and drive gear assembly. Replace the oil pump
gear and the drive gear assembly with new parts.
Note: Check all of the gears for worn teeth or damaged teeth. Replace the gears, if necessary.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:10:22 UTC+0800 2019
5/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146555
Engine Oil Pump - Install
SMCS - 1304-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00646132
1. Use Tool (A) to install the front oil seal (8) (not shown).
Illustration 2 g00607962
2. Lower the temperature of the spindle (10). Install spindle (10) and idler gear (11) as an
assembly in the front housing.
Note: The temperature of the spindle is lowered in order to ease the installation of the
spindle in the front housing.
Illustration 3 g00607955
3. Install set screw (9) in the front housing.
2/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 4 g00607885
4. Lower the temperature of the drive gear assembly. Install drive gear (7) in the front housing.
Note: The temperature of the drive gear assembly is lowered in order to ease the installation
of the drive gear assembly in the front housing.
Illustration 5 g00608012
Always wear protective gloves when handling parts that have been
heated.
3/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 5. Heat the oil pump gear up to 180 to 220 °C (356 to 428 °F). Support end (X) of the shaft (7)
(drive gear). Install oil pump gear (6) onto the shaft. The end of the gear (Z) should be flush
with the end of the shaft (Y) .
Illustration 6 g00607770
6. Install driven gear (4) into the front housing (slip fit).
Illustration 7 g00607826
7. Place gasket (3) and cover (2) in position on the front housing.
Note: Ensure that the old gasket material is removed from the mating surfaces.
8. Install the washer and bolt (1) that secures the cover to the front housing. Tighten bolt (1) to
a torque of 34 ± 5 N·m (25 ± 4 lb ft).
Refer to the Specifications Module, "Engine Oil Pump" for more information on the engine oil
pump.
End By: Install the front housing. Refer to Disassembly and Assembly, " Housing (Front) -
Install".
4/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:11:18 UTC+0800 2019
5/5(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01149671
Water Pump - Remove
SMCS - 1361-011
Removal Procedure
Start By:
A. Remove V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g00609950
2. Remove four bolts (1) that secure the water pump to the engine.
3. Remove water pump pulley (2) and water pump (3) as an unit from the engine.
4. Remove O-ring (4) (not shown) from water pump (3). Discard the old O-ring.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:12:13 UTC+0800 2019
2/2(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01566087
Water Pump - Disassemble
SMCS - 1361-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Group 1
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
Note: If the water pump is heated up to 80 °C (176 °F), the components can be easily removed.
1/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g00610108
1. Remove four bolts (1) and the washers that secure the water pump pulley to the water pump.
2. Remove water pump pulley (2) from the water pump.
Note: Check the groove for the V-belt of the water pump pulley for wear and damage. Replace the
water pump pulley, if necessary.
Note: Use Tool (C) during disassembly procedures of the water pump, which require the use of a
press or a hammer.
Illustration 2 g00610120
3. Use Tool (A) to remove flange (3) from the water pump.
2/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 3 g00610127
4. Use Tool (B) to remove retaining ring (4) from the water pump.
Illustration 4 g00610140
5. Use a press and Tool (C) to remove shaft assembly (5) from water pump assembly (6) .
3/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 5 g00813948
6. Remove impeller (8) from the shaft assembly (5) .
Note: Check the impeller for wear, corrosion, and metal to metal contact. Replace the impeller, if
necessary.
7. Remove the following items from shaft (9) :
◦ Bearing (10)
◦ Spacer (11)
◦ Bearing (12)
◦ Washer (13)
8. Once all of the components have been removed, then check shaft (9) for distortion. Replace the shaft,
if necessary.
9. Check seal (14) for wear and damage. Use Tool (C) in order to remove the seal from the water pump
housing, if necessary.
Note: Replace the seal if any signs of leakage occurs during the operation of the water pump.
10. Replace O-ring (7) with a new O-ring.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:13:09 UTC+0800 2019
4/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01566223
Water Pump - Assemble
SMCS - 1361-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 1P-1861 Retaining Ring Pliers 1
Note: Refer to Specifications, "Water Pump" for specifications that are required during assembly.
1/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 1 g00813948
1. Install seal (14), if the seal was removed during the disassembly procedures.
2. The following components are installed on shaft (9) :
◦ Washer (13)
◦ Bearing (12)
◦ Spacer (11)
◦ Bearing (10)
Note: Check two bearings (10) and (12) for correct rotation.
2/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 2 g00610140
3. Use a press and Tool (A) to install shaft assembly (5) into the water pump housing.
4. Use a press and Tool (A) to install impeller (8) onto shaft assembly (5) .
Illustration 3 g00610127
5. Use Tool (B) to install retaining ring (4) into the water pump housing.
6. Use a press and Tool (A) to install flange (3) onto shaft assembly (5) .
Illustration 4 g00610108
3/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 7. Install water pump pulley (2) onto the flange.
8. Install four bolts (1) in order to secure water pump pulley (2) to the flange.
End By: Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:14:05 UTC+0800 2019
4/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01149732
Water Pump - Install
SMCS - 1361-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00609950
1. Replace O-ring (4) (not shown) with a new part. Apply glycerine to the O-ring before the
installation of the water pump (3) and water pump pulley (2) .
1/2(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. 2. Install the water pump (3) and water pump pulley (2) as a unit onto the engine.
Note: When the water pump is installed, ensure that the grease fitting is up. Also, ensure
that the weep hole is down.
3. Install bolts (1) in order to secure water pump (3) to the cylinder block.
4. Fill the cooling system to the correct level. Refer to the appropriate Operation and
Maintenance Manual for the correct fluid and the correct filling procedure.
End By: Install V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:15:00 UTC+0800 2019
2/2(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01148678
Water Temperature Regulator - Remove and Install
SMCS - 1355-010
Removal Procedure
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant level below the water temperature regulator.
Illustration 1 g00609693
2. Loosen hose clamp (1) and disconnect hose (2) from cover (4) of the water temperature
regulator.
3. Remove two bolts (3) and the washers from cover (4) of the water temperature regulator.
4. Separate cover (4) from elbow (5) .
5. Remove bolts (6). Separate elbow (5) from the water outlet manifold.
6. Remove water temperature regulator (8) (not shown) from cover (4) .
7. Remove gasket (7) (not shown) and gasket (9) (not shown) from the mounting surfaces of
cover (4) and elbow (5) .
8. Use the following procedure in order to test the water temperature regulator:
a. Put the water temperature regulator in a tub of water. Heat the water in order to test
the water temperature regulator for thermostatic action.
Note: Stir the water in the tub in order to maintain even temperature during the test.
2/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. b. When the valve of the water temperature regulator lifts more than 10 mm (0.4 inch),
measure the water temperature.
Note: The opening temperature for the water temperature regulator is 71° ± 2°C (160°
± 3.6°F).
c. If the valve fails to operate properly, replace the water temperature regulator.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all of the mounting surfaces for the gaskets and remove all gasket material.
NOTICE
If the water temperature regulator is installed incorrectly, it will cause
the engine to overheat.
Illustration 2 g00609693
2. Install water temperature regulator (8) (not shown) into elbow (5) .
Note: When the water temperature regulator is installed, ensure that the hole for the air vent
is up.
3. Install gasket (7) (not shown) and gasket (9) (not shown).
3/4(W)w
2019/10/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...