This document provides instructions for disassembling and assembling the final drive of a 319D L excavator. The disassembly process involves using tools to remove 28 parts from the final drive assembly including the carrier assembly, ring gears, sun gear, and housing components. The assembly process reverses the disassembly steps and provides details on installing seals, bearings, and shims to properly preload the bearings.
Caterpillar cat 315 d l excavator (prefix ncm) service repair manual (ncm0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 318 f l excavator (prefix fft) service repair manual (fft0000...fjkskedmme
This document provides disassembly instructions for the final drive of a 318F L excavator. It describes 41 steps to fully disassemble the final drive components. Key steps include removing the sprocket, pistons, barrel assembly, springs, and various seals and plates. Safety warnings are provided to release pressures and contain fluids safely.
Caterpillar cat 325 c l excavator (prefix bkw) service repair manual (bkw0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 325C excavator. The disassembly procedure involves removing over 30 individual parts from the final drive housing. Cleanliness is emphasized throughout. The assembly procedure instructs to apply lubricants to parts and use pressing tools to reinstall bearings and seals. Proper torque specifications and alignment marks are noted as important.
Caterpillar cat 365 b excavator (prefix 9tz) service repair manual (9tz00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 assembly steps, specifying the required tools and explaining how to install components like bearings, seals, gears, and housings back into the final drive. Precautions like cleaning parts and applying lubricants are noted.
Caterpillar cat 315 d l excavator (prefix ncm) service repair manual (ncm0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 318 f l excavator (prefix fft) service repair manual (fft0000...fjkskedmme
This document provides disassembly instructions for the final drive of a 318F L excavator. It describes 41 steps to fully disassemble the final drive components. Key steps include removing the sprocket, pistons, barrel assembly, springs, and various seals and plates. Safety warnings are provided to release pressures and contain fluids safely.
Caterpillar cat 325 c l excavator (prefix bkw) service repair manual (bkw0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 325C excavator. The disassembly procedure involves removing over 30 individual parts from the final drive housing. Cleanliness is emphasized throughout. The assembly procedure instructs to apply lubricants to parts and use pressing tools to reinstall bearings and seals. Proper torque specifications and alignment marks are noted as important.
Caterpillar cat 365 b excavator (prefix 9tz) service repair manual (9tz00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 assembly steps, specifying the required tools and explaining how to install components like bearings, seals, gears, and housings back into the final drive. Precautions like cleaning parts and applying lubricants are noted.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 390 d l excavator (prefix wag) service repair manual (wag0000...fujskekfmsme
This document provides instructions for disassembling and assembling the final drive of a 390D L excavator. It lists the required tools and parts. The disassembly process involves removing over 30 components of the final drive including housing covers, gears, shafts, and seals. Photographs illustrate each step. Precautions are outlined to prevent dirt contamination. The assembly section lists a similar process and notes to inspect parts and apply sealant lubricants.
Caterpillar cat 374 f l excavator (prefix dnm) service repair manual (dnm0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. The disassembly process involves removing over 30 individual parts from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing new seals and determining the correct shim thickness between bearings and gears. Proper cleaning, application of sealants, and torque specifications are emphasized to correctly reassemble the final drive.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 14 m3 motor grader (prefix n9s) service repair manual (n9s000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M3 motor grader. It lists 51 steps to fully disassemble these components, including removing sprockets, bearings, seals, housings, gears, and other parts. Various tools are required, and weights of removed parts are provided. Detailed illustrations accompany each step to show how to properly disassemble the power train.
Caterpillar cat 324 d l excavator (prefix pyt) service repair manual (pyt0000...jfksekmmdme
This document provides instructions for assembling the final drive of a 324D L excavator. It outlines 30 steps, including installing bearings and seals, determining the correct shim thickness, and joining the main housing to the motor housing. Cleanliness is emphasized throughout the assembly process to prevent contamination. Various tools are required, and components should be lubricated before assembly.
Caterpillar cat 325 d l excavator (prefix gbr) service repair manual (gbr0000...hfjsekekmmd
The document provides instructions to disassemble a final drive for a 325D L excavator in 33 steps. It begins by removing the final drive and marking it for alignment. Various gears, washers, seals, and housing components are then removed. Carrier assemblies are disassembled by pressing out shafts and removing thrust washers and gears. Cleanliness is important to prevent dirt entry during reassembly.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 374 f l excavator (prefix ap4) service repair manual (ap40000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. The disassembly process involves removing over 30 individual parts from the final drive housing. The assembly process specifies cleaning and lubricating parts, setting the bearing preload using shims, and installing components in reverse order of disassembly. Precautions are provided regarding tool selection and lubrication of seals during assembly.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual Instant D...shanruliu7360
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...jdksmmdmdd
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...dujkdksmdmdm
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Cleanliness and applying lubricant to parts are emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...orrf0370383
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...fujkse9didkke3
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual Instant D...kubei069369925
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...fuusejkddmmd3e
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 390 d l excavator (prefix wag) service repair manual (wag0000...fujskekfmsme
This document provides instructions for disassembling and assembling the final drive of a 390D L excavator. It lists the required tools and parts. The disassembly process involves removing over 30 components of the final drive including housing covers, gears, shafts, and seals. Photographs illustrate each step. Precautions are outlined to prevent dirt contamination. The assembly section lists a similar process and notes to inspect parts and apply sealant lubricants.
Caterpillar cat 374 f l excavator (prefix dnm) service repair manual (dnm0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. The disassembly process involves removing over 30 individual parts from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing new seals and determining the correct shim thickness between bearings and gears. Proper cleaning, application of sealants, and torque specifications are emphasized to correctly reassemble the final drive.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 14 m3 motor grader (prefix n9s) service repair manual (n9s000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M3 motor grader. It lists 51 steps to fully disassemble these components, including removing sprockets, bearings, seals, housings, gears, and other parts. Various tools are required, and weights of removed parts are provided. Detailed illustrations accompany each step to show how to properly disassemble the power train.
Caterpillar cat 324 d l excavator (prefix pyt) service repair manual (pyt0000...jfksekmmdme
This document provides instructions for assembling the final drive of a 324D L excavator. It outlines 30 steps, including installing bearings and seals, determining the correct shim thickness, and joining the main housing to the motor housing. Cleanliness is emphasized throughout the assembly process to prevent contamination. Various tools are required, and components should be lubricated before assembly.
Caterpillar cat 325 d l excavator (prefix gbr) service repair manual (gbr0000...hfjsekekmmd
The document provides instructions to disassemble a final drive for a 325D L excavator in 33 steps. It begins by removing the final drive and marking it for alignment. Various gears, washers, seals, and housing components are then removed. Carrier assemblies are disassembled by pressing out shafts and removing thrust washers and gears. Cleanliness is important to prevent dirt entry during reassembly.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 374 f l excavator (prefix ap4) service repair manual (ap40000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. The disassembly process involves removing over 30 individual parts from the final drive housing. The assembly process specifies cleaning and lubricating parts, setting the bearing preload using shims, and installing components in reverse order of disassembly. Precautions are provided regarding tool selection and lubrication of seals during assembly.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual Instant D...shanruliu7360
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...jdksmmdmdd
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...dujkdksmdmdm
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Cleanliness and applying lubricant to parts are emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...orrf0370383
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...fujkse9didkke3
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual Instant D...kubei069369925
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...fuusejkddmmd3e
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 d l excavator (prefix ncm) service repair manual (ncm0000...fjjsekkdmme
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 315 d l excavator (prefix ncm) service repair manual (ncm0000...dkdmidkkdk
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Cleanliness and applying lubricant to parts are emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...fjkdksmmdm
This document provides instructions for disassembling and assembling a 315D L excavator final drive. The disassembly process involves removing 33 parts from the final drive assembly including the cover, carrier assembly, ring gears, and housing components. The assembly process describes installing 33 parts back into the final drive in reverse order and includes steps for preloading the bearings and determining the correct shim thickness. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Precautions are given to clean parts and apply sealant or lubricant during assembly.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...paws21610697
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves using various tools to remove over 30 individual components from the final drive housing. The assembly process reverses the disassembly steps and provides details on installing bearings, seals, gears, and other components back into the housing using presses, lifting devices, and installation tools. Precise measurements are taken to determine the correct shim thickness for preloading the bearings. Cleanliness and lubrication of parts is emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Precautions are given to clean parts and apply sealant or lubricant during assembly.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves using various tools to remove over 30 individual components from the final drive housing. The assembly process reverses the disassembly steps and provides details on installing bearings, seals, gears, and other components back into the housing using presses, lifting devices, and installation tools. Precise measurements are taken to determine the correct shim thickness for preloading the bearings. Cleanliness and lubrication of parts is emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Precautions are given to clean parts and apply sealant or lubricant during assembly.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Precautions are given to clean parts and apply sealant or lubricant during assembly.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjsjekdmmeme
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves using various tools to remove over 30 individual components from the final drive housing. The assembly process reverses the disassembly steps and provides details on installing bearings, seals, gears, and other components back into the housing using presses, lifting devices, and installation tools. Precise measurements are taken to determine the correct shim thickness for preloading the bearings. Cleanliness and lubrication of parts is emphasized throughout.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...cdfvvv1
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves using various tools to remove over 30 individual components from the final drive housing. The assembly process reverses the disassembly steps and provides details on installing bearings, seals, gears, and other components back into the housing using presses, lifting devices, and installation tools. Precise measurements are taken to determine the correct shim thickness for preloading the bearings. Cleanliness and lubrication of parts is emphasized throughout.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Precautions are given to clean parts and apply sealant or lubricant during assembly.
Similar to Caterpillar cat 319 d l excavator (prefix krm) service repair manual (krm00001 and up) (20)
Caterpillar cat 390 f l excavator (prefix hng) service repair manual (hng0000...fjskefksemer
This document provides instructions for removing and installing the front gear group on a C18 engine. The removal procedure involves taking off 14 parts including plates, gears, and seals. The installation procedure describes cleaning components and applying thread lock before reinstalling the 20 parts in reverse order while adjusting backlash as specified. Proper timing of the gears is critical to avoid engine damage.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjskefksemer
The document provides instructions for disassembling and assembling the travel motor on a 390F excavator. It describes 40 steps to disassemble the travel motor by removing components like the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 17 steps for reassembling the travel motor by reversing the disassembly process and ensuring proper installation of alignment marks and seals. Precision cleaning and installation of parts is emphasized.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install components such as the ring gear, carrier assemblies, gears, shafts, seals, bearings and housings. The procedure involves using lifting devices, pins, bolts and other fasteners to separate parts and reassemble the final drive. Weights of removed parts are provided to aid in lifting.
Caterpillar cat 374 f l excavator (prefix dnm) service repair manual (dnm0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install various components of the final drive such as the ring gear, carrier assemblies, sun gears, and housing components. Precautions are given to clean parts thoroughly, apply thread locking compounds, and verify that puller studs meet the capacity of any hydraulic cylinders used during the process.
Caterpillar cat 374 f l excavator (prefix at2) service repair manual (at20000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists 37 steps for disassembly, which include removing the final drive cover, carrier assemblies, gears, shafts, seals and housings. It then lists 17 steps for assembly, which include cleaning parts, applying anti-seize compound, installing bearings, seals and housings, and attaching the main housing to the motor housing. Tools required include lifting devices, puller studs, torque wrenches and seal installers. Safety precautions are provided for using hydraulic cylinders and puller studs during assembly.
Caterpillar cat 374 f l excavator (prefix ap4) service repair manual (ap40000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. The disassembly process involves removing over 30 individual parts from the final drive housing. The assembly process specifies cleaning and lubricating parts, setting the bearing preload using shims, and installing components in reverse order of disassembly. Precautions are provided regarding tool selection and lubrication of seals during assembly.
Caterpillar cat 374 d l excavator (prefix pja) service repair manual (pja0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 374D L Excavator. It describes 34 steps to disassemble the final drive by removing components like the ring gear, carrier assemblies, gears, shafts and seals. It then describes 8 steps for assembling the final drive, which involves cleaning parts, applying threadlocker, installing bearings and housings, and determining the correct shim number based on measuring gear dimensions. The document contains diagrams to illustrate each step in the procedures.
Caterpillar cat 374 d l excavator (prefix pax) service repair manual (pax0000...fjskefksemer
This document provides instructions for disassembling and assembling components of a 374D L excavator travel motor and final drive system. The multi-step process includes removing 17 bolts and other hardware to disassemble the final drive cover and housing, exposing internal parts like pistons, seals, and gears. Proper tooling and safety precautions are emphasized to correctly handle springs, weights up to 817kg, and contained hydraulic fluids during disassembly and reassembly.
Caterpillar cat 365 c l hydraulic excavator (prefix par) service repair manua...fjskefksemer
This document provides instructions for disassembling and assembling the travel motor of a 365C excavator. The disassembly process involves 29 steps to remove components like springs, plates, pistons, seals, and bearings. The assembly process describes 31 steps and requires tools to reinstall these components in the reverse order and adjust shims to ensure proper clearance is achieved. Precautions are provided to wear protective equipment when working with spring loaded components.
Caterpillar cat 365 c l excavator (prefix mcy) service repair manual (mcy0000...fjskefksemer
1) The document provides assembly instructions for a 365C L excavator final drive. It describes 36 steps to assemble components like bearings, gears, seals, housings and covers.
2) Precise measurements and torque specifications are listed to ensure proper bearing preload and component attachment.
3) Special tools are required to lift heavy parts, apply sealant and torque fasteners correctly during reassembly.
Caterpillar cat 349 e l vg excavator (prefix kcn) service repair manual (kcn0...fjskefksemer
This document provides assembly instructions for the final drive of a 349E L-VG excavator. It includes specifications for parts, required tools, and a step-by-step procedure. The procedure involves installing bearings, seals, gears, shafts, washers, and bolts in the proper order and orientation. Precise measurements and torque specifications are provided to ensure correct assembly.
Caterpillar cat 385 c l excavator (prefix t2e) service repair manual (t2e0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists 33 steps for disassembly, removing components like the housing cover, carrier assemblies, planetary gears, and seals. It notes that cleanliness is important to prevent damage. The assembly section lists one step to reassemble the final drive on the repair stand and cribbing, referring to other sections for installing components like seals. Proper cleaning and inspection of parts is emphasized along with using new replacement parts if any are worn or damaged.
Caterpillar cat 374 f l excavator (prefix nfj) service repair manual (nfj0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and presents 37 steps to disassemble the various components of the final drive, including removing the ring gear, carrier assemblies, sun gears, and housing components. The assembly section lists 2 steps, including cleaning all parts and reassembling the final drive while applying anti-seize compound to bearing surfaces. Safety notes warn about ensuring puller studs meet hydraulic cylinder capacity when used.
Caterpillar cat 349 e l vg excavator (prefix dge) service repair manual (dge0...fjskefksemer
This document provides instructions for disassembling and assembling the final drive on a 349E L-VG excavator. It describes 33 steps to disassemble the final drive components including removing bolts, gears, shafts, and housings. It also lists 13 specifications for reassembly and describes 17 steps to reassemble the final drive, applying sealant and torqueing bolts to specification. The document includes illustrations to clarify each step of the process.
Caterpillar cat 385 c l excavator (prefix eda) service repair manual (eda0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and parts. The disassembly process involves removing over 30 components of the final drive including housing covers, gears, shafts, and seals. Photos illustrate each step. Cleanliness is emphasized to prevent damage to precision parts. The assembly section states to reassemble in reverse order and check seals for wear before installation.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step details for removing components such as housing covers, gears, shafts, and seals. Cleanliness is emphasized throughout. The 34 steps describe taking the final drive apart piece by piece and include notes about weights of components and using lifting devices for heavy parts. Reassembly instructions are provided in the last step.
Caterpillar cat 390 f l excavator (prefix feh) service repair manual (feh0000...fjskefksemer
This document provides instructions for disassembling and assembling the travel motor on a 390F excavator model. It involves 40 steps to disassemble the various components of the travel motor including removing seals, springs, plates, pistons, and bearings. The assembly section outlines 31 steps to reinstall these components in reverse order while ensuring proper cleaning and alignment of parts. Precision tools are required and safety precautions mentioned to avoid injury from spring forces.
Caterpillar cat 345 c l hydraulic excavator (prefix tdg) service repair manua...fjskefksemer
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and housing pieces. It notes to mark parts locations and orientations. Reassembly follows the reverse order, and notes to clean parts and avoid damaging mating surfaces.
Caterpillar cat 345 c l hydraulic excavator (prefix lys) service repair manua...fjskefksemer
This document provides disassembly and assembly instructions for the final drive of a 345C L excavator. The final drive disassembly procedure involves 30 steps to remove components like the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure is not included in full but references using the required tools listed and applying thread lock, gasket sealant, and anti-seize compounds to correctly reassemble components.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 319D L EXCAVATOR KRM
Configuration: 319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i05453130
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
C 154-6181 Forcing Bolt 1
D 439-3940 Link Bracket 2
E
5F-7366 Forcing Bolt 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F - Loctite 5127 1
Start By:
a. Remove the final drive.
1/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly
clean the exterior of the component. This action will prevent dirt from entering the internal
mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from cover (2), and fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
3/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
4/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
5/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate two ring gears (17).
Note: Two ring gears (17) are held together with Tooling (F). It may be necessary to heat
ring gears (17) in order to soften the sealant. Do not heat over 135 °C (275 °F) for more
than thirty minutes.
6/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
7/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
8/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from main housing (18) once gear (26) is removed.
Make sure that the motor housing is supported.
Illustration 20 g00708211
25. Remove shims (27) from the main housing.
9/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from motor housing (28). The combined weight of main housing (18) and the final
drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
10/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 30 09:41:42 UTC+0800 2020
11/11
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 319D L EXCAVATOR KRM
Configuration: 319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i05453369
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
D 439-3940 Link Bracket 2
G 126-3994 Duo-Cone Seal Installer 1
H - Loctite C5-A Anti-Seize Lubricant
F - Loctite High Flex From-In-Place Gasket
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry
parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement. All disassembly and all
assembly procedures must be performed on a clean work surface and in a clean hydraulic
area. Keep cleaned parts covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound
during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
1. Install the final drive sprocket if the sprocket was removed from the main housing.
1/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 2. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Illustration 1 g00708215
3. Apply Tooling (H) to the outer diameter of the bearings.
4. Install bearings (32) and (33) in main housing (18) with a suitable press.
5. Make sure that bearing (32) and bearing (33) contact the counter bore in the main housing.
6. Use the following procedure to preload the bearings and determine the correct thickness of
shims.
Illustration 2 g00713058
a. Fasten Tooling (D) and a suitable lifting device to main housing (18). Install the main
housing on the motor housing.
b. Put the main housing and the motor housing in a suitable press.
2/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00709278
(a) Bearing surface
(b) Housing surface
c. Use a suitable press and a spacer in order to apply a load of 4000 kg (8819 lb) on the
bearings. Rotate the housing in order to seat the bearings.
d. Reduce the load on the bearings to 1000 ± 100 kg (2205 ± 221 lb).
e. Use a depth micrometer in order to measure the step length between the bearing
surface and the housing surface. Take measurements at several different locations
around the housing. Compute the average of the measured dimensions and record the
number. Call this Dimension (Y).
Illustration 4 g00709276
f. Use a depth micrometer in order to measure the step length of gear (26). Take
measurements at several different locations around the gear. Compute the average of
the measured dimensions and record the number. Call this Dimension (X).
g. The thickness of the shims is equal to (X − Y) ± 0.05 mm (0.002 inch).
Note: Use no more than two shims. If two shims are required, install the thinner shim
next to the gear.
h. Remove the main housing from the motor housing.
3/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g01021370
7. Use Tooling (G) in order to install Duo-Cone seal (31) in main housing (18). Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
Illustration 6 g01021371
8. Use Tooling (G) in order to install Duo-Cone seal (29) in motor housing (28).
Illustration 7 g00708214
4/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 9. Apply Tooling (H) to the surfaces that contact pins (30).
10. Install alignment pins (30).
Note: Do not damage the Duo-Cone seals in the main housing or in the motor housing
during the assembly of the two components. After installation of the main housing on the
motor housing, there will be a small gap between the components. The gap is caused by the
Duo-Cone seals. This gap will be eliminated during installation of gear (26).
Illustration 8 g00713058
11. Fasten Tooling (D) and a suitable lifting device to main housing (18). Install the main
housing on the motor housing.
Illustration 9 g00708211
12. Install shims (27) that were determined in Step 6.g in the main housing.
Note: If two shims are required, install the thinner shim next to the gear.
5/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00708187
13. Install gear (26).
14. Install bolts (25) in gear (26). Install the bolts in an even pattern until the gear is seated
against the bearing. Tighten bolts (25) in a crisscross pattern.
Illustration 11 g00708186
15. Install O-ring seal (24) to main housing (18).
Illustration 12 g00708175
16. Assemble carrier assembly (15), as follows.
6/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 13 g00708220
a. Install bearings (22) in planetary gear (23).
b. Install thrust washers (21) and planetary gear (23) in the carrier assembly.
c. Use a deburring tool in order to remove the metal burr from the openings in the
carrier. Install planetary shaft (19) in the carrier assembly.
d. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
Illustration 14 g00513451
e. Orient the split in spring pin (20) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
17. Repeat Steps 16.a through 16.e in order to install the remaining planetary gears in the carrier
assembly.
7/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g00708172
18. Install a lifting sling through the middle of carrier assembly (15). Fasten a 12.7 mm
(0.50 inch) shackle to the suitable lifting device.
19. Install carrier assembly (15) on the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Remove the shackle and the suitable lifting device.
Illustration 16 g00713148
21. Apply Tooling (F) to the mating surface of ring gear (17b).
22. Install ring gear (17a) on ring gear (17b).
8/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 17 g00708184
23. Fasten a suitable lifting device to ring gears (17), as shown. Install the ring gears to main
housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 18 g00708325
24. Install spacer (16) in the carrier assembly.
Illustration 19 g00708162
25. Install sun gear (14) in carrier assembly (15).
9/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP5...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 20 g01304883
Illustration 21 g00708218
26. Assemble carrier assembly (7), as follows.
a. Install bearing (12) in planetary gear (13).
b. Install thrust washers (11) and planetary gear (13) in the carrier assembly.
c. Install planetary shaft (9) in the carrier assembly.
d. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 22 g00513451
e. Orient the split in spring pin (10) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
10/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 27. Repeat Steps 26.a through 26.e in order to install the remaining planetary gears in the carrier
assembly.
Illustration 23 g00708092
28. Install carrier assembly (7) in the ring gear. The weight of carrier assembly (7) is
approximately 14 kg (30 lb).
29. Install sun gear (8) in carrier assembly (7).
30. Install spacer (6) in carrier assembly (7).
Illustration 24 g00708235
31. Install new O-ring seals (5) on plugs (4) that were in the cover.
11/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 25 g00708091
32. Install plugs (4) in cover (2). Tighten plugs (4) to a torque of 80 ± 10 N·m (59 ± 7 lb ft).
33. Install thrust plate (3) in cover (2).
34. Apply Tooling (F) to the mating surface of the ring gear.
Illustration 26 g00708090
35. Fasten Tooling (B) and a suitable lifting device to cover (2), as shown. The weight of cover
(2) is approximately 32 kg (70 lb). Install cover (2).
36. Remove Tooling (B) and install the setscrews in cover (2).
Illustration 27 g00708089
37. Install bolts (1) and the washers that hold the cover in position. Tighten bolts (1) in a
crisscross pattern.
38. Remove the final drive from Tooling (A). The combined weight of the final drive and final
drive sprocket is approximately 310 kg (683 lb).
End By:
a. Install the final drive.
12/13
319D L Excavator KRM00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...