This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and housing. It then lists 7 notes and 28 steps to reassemble the final drive by installing components like seals, bearings, shims, and housing pieces in the reverse order of disassembly. The goal is to carefully disassemble and reassemble the final drive to the original locations and specifications.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...f8usejkdmmd8i
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...gongfuao7509
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and outlines 33 steps to disassemble the various components of the final drive, including removing gears, shafts, washers, seals, and housings. It then lists 14 steps for reassembling the final drive, including pressing bearings into place, installing seals, aligning pins, and attaching housings and gears. Precautions are provided regarding cleanliness and applying lubricants during assembly.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...tengtui535
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying sealant and anti-seize compound, and setting proper bearing preload using shims. The goal is to correctly disassemble and reassemble all parts of the final drive.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...yu5676962
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and gives step-by-step procedures to remove components like the carrier assembly, ring gears, and housing. Instructions are also provided for inspecting parts, applying lubricants, and installing components like seals, bearings, and shims during reassembly. The goal is to disassemble and reassemble the final drive while maintaining cleanliness and applying the proper preloads to components.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and main housing. It then lists notes on cleanliness and provides 14 steps to reassemble the final drive components in reverse order.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive sprocket, carrier assembly, ring gears, and other components. It also lists notes on cleanliness and includes 14 steps for reassembling the final drive components.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...f8usejkdmmd8i
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...gongfuao7509
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and outlines 33 steps to disassemble the various components of the final drive, including removing gears, shafts, washers, seals, and housings. It then lists 14 steps for reassembling the final drive, including pressing bearings into place, installing seals, aligning pins, and attaching housings and gears. Precautions are provided regarding cleanliness and applying lubricants during assembly.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...tengtui535
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying sealant and anti-seize compound, and setting proper bearing preload using shims. The goal is to correctly disassemble and reassemble all parts of the final drive.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...yu5676962
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and gives step-by-step procedures to remove components like the carrier assembly, ring gears, and housing. Instructions are also provided for inspecting parts, applying lubricants, and installing components like seals, bearings, and shims during reassembly. The goal is to disassemble and reassemble the final drive while maintaining cleanliness and applying the proper preloads to components.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and main housing. It then lists notes on cleanliness and provides 14 steps to reassemble the final drive components in reverse order.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive sprocket, carrier assembly, ring gears, and other components. It also lists notes on cleanliness and includes 14 steps for reassembling the final drive components.
Caterpillar Cat 318C L Excavator (Prefix GPA) Service Repair Manual (GPA00001...f8usiejdkmdd
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gears, and housing. Instructions are also provided for installing bearings, seals, and other parts in reverse order during assembly. Proper cleaning, lubrication, and torque specifications are emphasized throughout.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive sprocket, carrier assembly, ring gears, and other components. It then lists notes on cleanliness and provides 14 steps for reassembling the final drive, including installing bearings, shims, and seals. The purpose is to provide maintenance technicians with a procedure for taking apart and rebuilding the excavator's final drive system.
Caterpillar cat 318 c ln excavator (prefix gpa) service repair manual (gpa000...f9oseikkdks
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and gives step-by-step procedures to remove components like the carrier assembly, ring gears, and housing. Bearings and seals are removed and installed. Precise shim thickness is determined to set bearing preload when reassembling. Cleanliness is emphasized throughout.
Caterpillar cat 318 c excavator (prefix gpa) service repair manual (gpa00001 ...f9oseikkdks
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive sprocket, carrier assembly, ring gears, and other components. It then lists one note about cleanliness and assembly before outlining 14 steps for reassembling the final drive, including installing bearings, shims, and seals. The purpose is to provide maintenance technicians with a procedure for taking apart and rebuilding the excavator's final drive system.
Caterpillar cat 318 c l excavator (prefix gpa) service repair manual (gpa0000...f9oseikkdks
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and gives step-by-step procedures to remove components like the carrier assembly, ring gears, and housing. Bearings and seals are removed and installed. Precise shim thickness is determined to set bearing preload. Cleanliness is emphasized throughout.
Caterpillar cat 318 c ln excavator (prefix gpa) service repair manual (gpa000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 318 c l excavator (prefix gpa) service repair manual (gpa0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 318 c excavator (prefix gpa) service repair manual (gpa00001 ...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
Caterpillar Cat 318C L Excavator (Prefix GPA) Service Repair Manual (GPA00001...jfkskmdmmdd
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and outlines 33 steps to disassemble the various components of the final drive, including removing gears, shafts, washers, seals, and housings. It then lists 14 steps to reassemble the final drive, including pressing bearings into place, installing seals, aligning pins, and attaching housings and gears. Precautions are provided regarding cleanliness and applying lubricants during assembly.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...gongfuao7509
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into the motor housing in the specified order.
3. Attaching lifting brackets and safely lifting the heavy swing motor or drive components during removal and installation procedures.
Caterpillar Cat 329D and 329D L Excavator (Prefix DTZ) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar Cat 324D FM LL EXCAVATOR (Prefix JLS) Service Repair Manual Insta...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 324D FM LL EXCAVATOR. It outlines 21 steps for disassembly, which include removing plates, springs, pistons, gears, and other components. It also outlines 16 steps for assembly, which include installing bearings, seals, gears, and other components back into the final drive housing using various tools. The document includes illustrations to supplement the written instructions.
Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Man...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It lists 30 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps to reassemble the final drive by installing components like bearings, seals, gears, and shims in the reverse order of disassembly. Precise tools and procedures are required due to the heavy weight and precision fitting of components.
Caterpillar Cat 323D2 and 323D2 L Excavator (Prefix JEX) Service Repair Manua...gongfuao7509
The document provides instructions for disassembling the final drive of an excavator model 323D2. It involves 33 steps including removing the final drive cover, carrier assembly, ring gears, and other components. Various tools are required including a transmission repair stand, link brackets, forcing screws, and puller assembly. Cleanliness is important to prevent dirt from entering internal parts during disassembly.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual Instant ...gongfuao7509
The document provides instructions for removing the engine oil filter base from a 322C FM excavator with a 3126 engine. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the oil filter base mounting surface before installing the new oil filter base. The summary is provided in 3 sentences or less as requested.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual Instant ...gongfuao7509
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse of removal.
3. Turbocharger removal requires removing bolts and nuts connecting it to the exhaust manifold and disconnecting oil lines. Disassembly separates the housing components. Assembly reconnects the parts and installation bolts the turbocharger back into place.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual Instant ...gongfuao7509
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, replacing seals, and using tools to install the governor along with associated lines, pins, and clips. Precautions are given to keep parts clean and ensure free movement of components.
More Related Content
Similar to Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix MDY) Service Repair Manual Instant Download.pdf
Caterpillar Cat 318C L Excavator (Prefix GPA) Service Repair Manual (GPA00001...f8usiejdkmdd
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gears, and housing. Instructions are also provided for installing bearings, seals, and other parts in reverse order during assembly. Proper cleaning, lubrication, and torque specifications are emphasized throughout.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive sprocket, carrier assembly, ring gears, and other components. It then lists notes on cleanliness and provides 14 steps for reassembling the final drive, including installing bearings, shims, and seals. The purpose is to provide maintenance technicians with a procedure for taking apart and rebuilding the excavator's final drive system.
Caterpillar cat 318 c ln excavator (prefix gpa) service repair manual (gpa000...f9oseikkdks
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and gives step-by-step procedures to remove components like the carrier assembly, ring gears, and housing. Bearings and seals are removed and installed. Precise shim thickness is determined to set bearing preload when reassembling. Cleanliness is emphasized throughout.
Caterpillar cat 318 c excavator (prefix gpa) service repair manual (gpa00001 ...f9oseikkdks
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive sprocket, carrier assembly, ring gears, and other components. It then lists one note about cleanliness and assembly before outlining 14 steps for reassembling the final drive, including installing bearings, shims, and seals. The purpose is to provide maintenance technicians with a procedure for taking apart and rebuilding the excavator's final drive system.
Caterpillar cat 318 c l excavator (prefix gpa) service repair manual (gpa0000...f9oseikkdks
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and gives step-by-step procedures to remove components like the carrier assembly, ring gears, and housing. Bearings and seals are removed and installed. Precise shim thickness is determined to set bearing preload. Cleanliness is emphasized throughout.
Caterpillar cat 318 c ln excavator (prefix gpa) service repair manual (gpa000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 318 c l excavator (prefix gpa) service repair manual (gpa0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 318 c excavator (prefix gpa) service repair manual (gpa00001 ...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
Caterpillar Cat 318C L Excavator (Prefix GPA) Service Repair Manual (GPA00001...jfkskmdmmdd
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and outlines 33 steps to disassemble the various components of the final drive, including removing gears, shafts, washers, seals, and housings. It then lists 14 steps to reassemble the final drive, including pressing bearings into place, installing seals, aligning pins, and attaching housings and gears. Precautions are provided regarding cleanliness and applying lubricants during assembly.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling parts and includes notes about cleaning, applying lubricants, and setting proper bearing preload using shims.
Similar to Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix MDY) Service Repair Manual Instant Download.pdf (11)
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...gongfuao7509
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into the motor housing in the specified order.
3. Attaching lifting brackets and safely lifting the heavy swing motor or drive components during removal and installation procedures.
Caterpillar Cat 329D and 329D L Excavator (Prefix DTZ) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar Cat 324D FM LL EXCAVATOR (Prefix JLS) Service Repair Manual Insta...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 324D FM LL EXCAVATOR. It outlines 21 steps for disassembly, which include removing plates, springs, pistons, gears, and other components. It also outlines 16 steps for assembly, which include installing bearings, seals, gears, and other components back into the final drive housing using various tools. The document includes illustrations to supplement the written instructions.
Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Man...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It lists 30 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps to reassemble the final drive by installing components like bearings, seals, gears, and shims in the reverse order of disassembly. Precise tools and procedures are required due to the heavy weight and precision fitting of components.
Caterpillar Cat 323D2 and 323D2 L Excavator (Prefix JEX) Service Repair Manua...gongfuao7509
The document provides instructions for disassembling the final drive of an excavator model 323D2. It involves 33 steps including removing the final drive cover, carrier assembly, ring gears, and other components. Various tools are required including a transmission repair stand, link brackets, forcing screws, and puller assembly. Cleanliness is important to prevent dirt from entering internal parts during disassembly.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual Instant ...gongfuao7509
The document provides instructions for removing the engine oil filter base from a 322C FM excavator with a 3126 engine. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the oil filter base mounting surface before installing the new oil filter base. The summary is provided in 3 sentences or less as requested.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual Instant ...gongfuao7509
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse of removal.
3. Turbocharger removal requires removing bolts and nuts connecting it to the exhaust manifold and disconnecting oil lines. Disassembly separates the housing components. Assembly reconnects the parts and installation bolts the turbocharger back into place.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual Instant ...gongfuao7509
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, replacing seals, and using tools to install the governor along with associated lines, pins, and clips. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 1YS) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the governor and associated components on a Caterpillar 3116 engine. The removal process involves disconnecting linkages and tubes, removing mounting bolts and clips, and using specialized tools. The installation follows the removal steps in reverse, applying lubricant to seals and ensuring proper adjustment of linkages. Required tools include various pliers and pin tools to facilitate disconnecting and reconnecting components.
Caterpillar Cat 322 L EXCAVATOR (Prefix 9RL) Service Repair Manual Instant Do...gongfuao7509
This document provides instructions for removing and installing a governor from a Caterpillar Cat 322 L excavator powered by a 3116 engine. The removal procedure involves disconnecting tubes, removing clips and bolts, and using special tools. The installation procedure describes cleaning and lubricating parts, replacing seals, and using tools to install the governor components in reverse order of removal. Proper torque specifications and checks are listed to ensure correct installation.
This document provides instructions for servicing the air conditioning system on Caterpillar 322 and 322L excavators. It describes safety precautions when working with refrigerant due to risks of injury. The document outlines procedures for preparing the machine, removing and installing various AC system components like lines, the compressor, and preparing the system for disassembly and reassembly. Detailed steps are provided for correctly assembling refrigerant line fittings and other components.
Caterpillar Cat 320F L Excavator (Prefix YBM) Service Repair Manual Instant D...gongfuao7509
The document provides instructions for removing and installing a boom cylinder on an excavator. Key steps include:
1. Lowering the boom and releasing hydraulic pressure before removal.
2. Detaching hoses and removing bolts and pins to separate the cylinder from the excavator.
3. Lifting the cylinder, which weighs approximately 287kg, off the excavator using slings.
4. Reinstalling involves lifting the cylinder back into place with slings, reattaching with bolts and pins, and reconnecting hoses. Torque specifications are provided for all fasteners.
This document provides instructions for removing and installing a flywheel on a 320E LRR excavator with a C6.6 engine. The removal procedure involves using guide studs and lifting equipment to support the flywheel, then removing mounting bolts. The installation procedure specifies cleaning and inspecting components, positioning the flywheel with guide studs and lifting equipment, and tightening mounting bolts to the specified torque. Instructions are also provided for removing and installing a crankshaft rear seal.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for performing maintenance on the engine's crankshaft pulley, vibration damper, front seal, and front cover. Precautions are provided to keep parts clean and torque specifications are given.
This document provides instructions for disassembling and assembling the gear pump (pilot) and main hydraulic pump on a Caterpillar 320D2 excavator. The summary includes steps to disassemble the gear pump by removing housing bolts, seals, gears, and plates. It also describes removing the main hydraulic pump by disconnecting hoses and harnesses, removing mounting bolts, and lifting out the pump along with attached auxiliary pumps and pilots.
The document provides instructions for disassembling and assembling the travel motor of a 320D2L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, check valves, fittings, pistons, plates, seals and more. It then describes 25 steps to reassemble the travel motor, replacing components in the reverse order and ensuring proper alignment of parts like keys and cam plates. Special care must be taken to avoid damaging parts and keep components matched during assembly.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318C EXCAVATOR MDY
Configuration: 318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
318C Excavator Machine Systems
Media Number -RENR6647-04 Publication Date -01/03/2009 Date Updated -05/03/2009
i02606369
Final Drive - Disassemble
SMCS - 4050-015
S/N - GPA1-UP
S/N - MDY1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
1/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
3/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
4/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
5/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
6/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
7/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
8/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
Illustration 20 g00708211
25. Remove shims (27) from the main housing.
9/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
10/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 306...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 22 11:50:49 UTC+0800 2020
11/11
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 306...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318C EXCAVATOR MDY
Configuration: 318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
318C Excavator Machine Systems
Media Number -RENR6647-04 Publication Date -01/03/2009 Date Updated -05/03/2009
i03949150
Final Drive - Assemble
SMCS - 4050-016
S/N - GPA1-UP
S/N - MDY1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
D 138-7574 Link Bracket 2
G 126-3994 Duo-Cone Seal Installer 1
H 5P-3931 Anti-Seize Compound
F 1U-8846 Gasket Sealant
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry
parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement. All disassembly and all
assembly procedures must be performed on a clean work surface and in a clean hydraulic
area. Keep cleaned parts covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound
during the assembly procedure.
1/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: Apply a light film of hydraulic oil to all components before assembly.
1. Install the final drive sprocket if the sprocket was removed from the main housing.
2. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Illustration 1 g00708215
3. Apply Tooling (H) to the outer diameter of the bearings.
4. Install bearings (32) and (33) in main housing (18) with a suitable press.
5. Make sure that bearing (32) and bearing (33) contact the counterbore in the main housing.
6. Use the following procedure to preload the bearings and determine the correct thickness of
shims.
Illustration 2 g00713058
a. Fasten Tooling (D) and a suitable lifting device to main housing (18) . Install the main
housing on the motor housing.
b. Put the main housing and the motor housing in a suitable press.
2/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00709278
(a) Bearing surface
(b) Housing surface
c. Use a suitable press and a spacer in order to apply a load of 4000 kg (8818.5 lb) on
the bearings. Rotate the housing in order to seat the bearings.
d. Reduce the load on the bearings to 1000 ± 100 kg (2204.6 ± 220.5 lb).
e. Use a depth micrometer in order to measure the step length between the bearing
surface and the housing surface. Take measurements at several different locations
around the housing. Compute the average of the measured dimensions and record the
number. Call this Dimension (Y) .
Illustration 4 g00709276
f. Use a depth micrometer in order to measure the step length of the coupling gear (26) .
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this Dimension (X) .
g. The thickness of the shims is equal to (X - Y) ± 0.05 mm (0.002 inch).
Note: Use no more than two shims. If two shims are required, install the thinner shim
next to the gear.
3/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. h. Remove the main housing from the motor housing.
Illustration 5 g01021370
7. Use Tooling (G) in order to install Duo-Cone seal (31) in main housing (18) . Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
Illustration 6 g01021371
8. Use Tooling (G) in order to install Duo-Cone seal (29) in motor housing (28) .
4/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 7 g00708214
9. Apply Tooling (H) to the surfaces that contact pins (30) .
10. Install alignment pins (30) .
Note: Do not damage the Duo-Cone seals in the main housing or in the motor housing
during the assembly of the two components. After installation of the main housing on the
motor housing, there will be a small gap between the components. The gap is caused by the
Duo-Cone seals. This gap will be eliminated during installation of gear (26) .
Illustration 8 g00713058
11. Fasten Tooling (D) and a suitable lifting device to main housing (18) . Install the main
housing on the motor housing.
5/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 9 g00708211
12. Install shims (27) that were determined in Step 6.g in the main housing.
Note: If two shims are required, install the thinner shim next to the gear.
Illustration 10 g00708187
13. Install gear (26) .
14. Install bolts (25) in gear (26) . Install the bolts in an even pattern until the gear is seated
against the bearing. Tighten bolts (25) in a crisscross pattern.
6/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 11 g00708186
15. Install O-ring seal (24) to main housing (18) .
Illustration 12 g00708175
16. Assemble carrier assembly (15) , as follows.
Illustration 13 g00708220
a. Install bearings (22) in planetary gear (23) .
7/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. b. Install thrust washers (21) and planetary gear (23) in the carrier assembly.
c. Use a deburring tool in order to remove the metal burr from the openings in the
carrier. Install planetary shaft (19) in the carrier assembly.
d. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
Illustration 14 g00513451
e. Orient the split in spring pin (20) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
17. Repeat Steps 16.a through 16.e in order to install the remaining planetary gears in the carrier
assembly.
Illustration 15 g00708172
8/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 18. Install a lifting sling through the middle of carrier assembly (15) . Fasten a 12.7 mm (0.50
inch) shackle to the suitable lifting device.
19. Install carrier assembly (15) on the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Remove the shackle and the suitable lifting device.
Illustration 16 g00713148
21. Apply Tooling (F) to the mating surface of ring gear (17b) .
22. Install ring gear (17a) on ring gear (17b) .
Illustration 17 g00708184
23. Fasten a suitable lifting device to ring gears (17) , as shown. Install the ring gears to main
housing (18) . The weight of ring gears (17) is approximately 45 kg (100 lb).
9/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 3066 E...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 18 g00708325
24. Install spacer (16) in the carrier assembly.
Illustration 19 g00708162
25. Install sun gear (14) in carrier assembly (15) .
Illustration 20 g01304883
10/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 306...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 21 g00708218
26. Assemble carrier assembly (7) , as follows.
a. Install bearing (12) in planetary gear (13) .
b. Install thrust washers (11) and planetary gear (13) in the carrier assembly.
c. Install planetary shaft (9) in the carrier assembly.
d. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 22 g00513451
e. Orient the split in spring pin (10) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
27. Repeat Steps 26.a through 26.e in order to install the remaining planetary gears in the carrier
assembly.
11/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 306...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 23 g00708092
28. Install carrier assembly (7) in the ring gear. The weight of carrier assembly (7) is
approximately 14 kg (30 lb).
29. Install sun gear (8) in carrier assembly (7) .
30. Install spacer (6) in carrier assembly (7) .
Illustration 24 g00708235
31. Install new O-ring seals (5) on plugs (4) that were in the cover.
12/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 306...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. Illustration 25 g00708091
32. Install plugs (4) in cover (2) . Tighten plugs (4) to a torque of 80 ± 10 N·m (59 ± 7 lb ft).
33. Install thrust plate (3) in cover (2) .
34. Apply Tooling (F) to the mating surface of the ring gear.
Illustration 26 g00708090
35. Fasten Tooling (B) and a suitable lifting device to cover (2) , as shown. The weight of cover
(2) is approximately 32 kg (70 lb). Install cover (2) .
36. Remove Tooling (B) . Install the setscrews in cover (2) .
13/14
318C L & 318C LN Excavators MDY00001-UP (MACHINE) POWERED BY 306...
2020/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...