This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves 27 steps to remove components from the travel motor in the correct order. This includes removing the head, brake piston, barrel assembly, shoe retainer, and shaft assembly. The assembly process reverses the disassembly with 27 steps and provides notices to ensure proper installation of seals, keys, and other components.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...orrf0370383
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins by describing how to disassemble the travel motor by removing 27 different components and parts. These include removing the head, brake piston, barrel assembly, cam plate and more. It then describes the 25 steps to assemble the travel motor, putting in place components like the shaft assembly, piston guide, friction plates and more. Precise installation of seals, rings and alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual Instant D...rishang96299
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing components like the head, brake piston, barrel assembly, and shaft assembly. It then lists 26 steps for assembly, which describe cleaning components and installing them in reverse order, like pressing the shaft assembly into the body and installing the barrel assembly while keeping the cam plate engaged. Precautions are given to prevent damage and ensure correct alignment of parts.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual Instant D...shanruliu7360
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly aligned. Special tools and precautions are noted to properly complete the process.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...jdksmmdmdd
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly positioned. Special tools and precautions are noted to ensure proper reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...dujkdksmdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, shoe retainer, and shaft. The assembly section lists 28 steps to reinstall these components in the reverse order, noting that alignment marks and original locations must be followed to ensure proper reassembly. Precautions are provided to contain fluids, retain component identification, and install keys and pins correctly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...fuusejkddmmd3e
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly components, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly aligned. Special tools and precautions are noted to ensure proper reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual Instant D...kubei069369925
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing components like the head, brake piston, barrel assembly, and shaft assembly. It then lists 26 steps for assembly, which describe cleaning components and installing them in reverse order, like installing the shaft assembly, barrel assembly, brake piston, and head. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...fujkse9didkke3
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly aligned. Special tools and precautions are noted to properly complete the process.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...orrf0370383
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins by describing how to disassemble the travel motor by removing 27 different components and parts. These include removing the head, brake piston, barrel assembly, cam plate and more. It then describes the 25 steps to assemble the travel motor, putting in place components like the shaft assembly, piston guide, friction plates and more. Precise installation of seals, rings and alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual Instant D...rishang96299
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing components like the head, brake piston, barrel assembly, and shaft assembly. It then lists 26 steps for assembly, which describe cleaning components and installing them in reverse order, like pressing the shaft assembly into the body and installing the barrel assembly while keeping the cam plate engaged. Precautions are given to prevent damage and ensure correct alignment of parts.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual Instant D...shanruliu7360
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly aligned. Special tools and precautions are noted to properly complete the process.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...jdksmmdmdd
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly positioned. Special tools and precautions are noted to ensure proper reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...dujkdksmdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, shoe retainer, and shaft. The assembly section lists 28 steps to reinstall these components in the reverse order, noting that alignment marks and original locations must be followed to ensure proper reassembly. Precautions are provided to contain fluids, retain component identification, and install keys and pins correctly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...fuusejkddmmd3e
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly components, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly aligned. Special tools and precautions are noted to ensure proper reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual Instant D...kubei069369925
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing components like the head, brake piston, barrel assembly, and shaft assembly. It then lists 26 steps for assembly, which describe cleaning components and installing them in reverse order, like installing the shaft assembly, barrel assembly, brake piston, and head. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...fujkse9didkke3
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly aligned. Special tools and precautions are noted to properly complete the process.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...dkdmidkkdk
This document provides instructions for disassembling and assembling a travel motor. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, shoe retainer, and shaft. The assembly section outlines 13 steps starting with installing retaining rings on the shaft and ending by engaging the cam plate with keys in the motor body. Proper cleaning, alignment marks, and lubrication are emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...fjkdksmmdm
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing components like the head, brake piston, barrel assembly, and shaft assembly. It then lists 26 steps for assembly, which describe cleaning components and installing them in reverse order, like pressing the shaft assembly into the body and installing the barrel assembly while keeping the cam plate engaged. Precautions are given to prevent damage and ensure correct alignment of parts.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...tuzhiyou2
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, cam plate, shaft assembly and more. The assembly process has 24 steps and instructs technicians to thoroughly clean parts, apply lubricants, and reinstall components in their original positions and orientations. Technicians are warned to take care handling parts and aligning components properly to prevent damage.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, cam plate, shaft assembly and more. The assembly process has 24 steps and instructs technicians to thoroughly clean parts, apply lubricants, and reinstall components in their original positions and orientations. Technicians are warned to take care handling parts and aligning components properly to prevent damage.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...kesi7153062
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process involves removing 24 components from the travel motor in 27 steps. Key steps include removing the head, check valve assemblies, fittings, brake piston, piston guide, barrel assembly, shoe retainer, and shaft assembly. The assembly process reverses the disassembly with 27 steps to install the components back into the travel motor in the reverse order, taking care to maintain proper alignment and orientation of parts.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...shudun96087
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, check valves, fittings, brake piston, friction plates, barrel assembly, shoe retainer, and shaft assembly. The assembly process reverses the disassembly with 23 steps like installing the shaft assembly, keys, cam plate and other components in their proper positions and orientations. Precautions are given to prevent damage and ensure proper alignment of parts.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...jse7039222
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing various components like the head, check valves, fittings, brake piston, piston guide, barrel assembly, and shaft assembly. It then lists 22 steps for assembly, covering installation of seals, plates, piston shoe assemblies, cam plate, springs, and other components in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...kesi7153062
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing various components like the head, check valves, fittings, brake piston, piston guide, barrel assembly, and shaft assembly. It then lists 22 steps for assembly, covering installation of seals, plates, piston shoe assemblies, cam plate, springs, and other components in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...jdkskmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...prmy389342
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft. The assembly process describes 25 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...8ufjsekddm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar cat 323 d2 l excavator (prefix pjp) service repair manual (pjp000...idkdkddmd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...dujkdksmdmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to position the front cover and hand tighten bolts.
4. Align the front cover and tighten the bolts. Install a new front seal and reinstall any removed components.
More Related Content
Similar to Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001 and up).pdf
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...dkdmidkkdk
This document provides instructions for disassembling and assembling a travel motor. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, shoe retainer, and shaft. The assembly section outlines 13 steps starting with installing retaining rings on the shaft and ending by engaging the cam plate with keys in the motor body. Proper cleaning, alignment marks, and lubrication are emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...fjkdksmmdm
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing components like the head, brake piston, barrel assembly, and shaft assembly. It then lists 26 steps for assembly, which describe cleaning components and installing them in reverse order, like pressing the shaft assembly into the body and installing the barrel assembly while keeping the cam plate engaged. Precautions are given to prevent damage and ensure correct alignment of parts.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjjsekkdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...tuzhiyou2
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, cam plate, shaft assembly and more. The assembly process has 24 steps and instructs technicians to thoroughly clean parts, apply lubricants, and reinstall components in their original positions and orientations. Technicians are warned to take care handling parts and aligning components properly to prevent damage.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, cam plate, shaft assembly and more. The assembly process has 24 steps and instructs technicians to thoroughly clean parts, apply lubricants, and reinstall components in their original positions and orientations. Technicians are warned to take care handling parts and aligning components properly to prevent damage.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...kesi7153062
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process involves removing 24 components from the travel motor in 27 steps. Key steps include removing the head, check valve assemblies, fittings, brake piston, piston guide, barrel assembly, shoe retainer, and shaft assembly. The assembly process reverses the disassembly with 27 steps to install the components back into the travel motor in the reverse order, taking care to maintain proper alignment and orientation of parts.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...shudun96087
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, check valves, fittings, brake piston, friction plates, barrel assembly, shoe retainer, and shaft assembly. The assembly process reverses the disassembly with 23 steps like installing the shaft assembly, keys, cam plate and other components in their proper positions and orientations. Precautions are given to prevent damage and ensure proper alignment of parts.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...jse7039222
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing various components like the head, check valves, fittings, brake piston, piston guide, barrel assembly, and shaft assembly. It then lists 22 steps for assembly, covering installation of seals, plates, piston shoe assemblies, cam plate, springs, and other components in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...kesi7153062
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing various components like the head, check valves, fittings, brake piston, piston guide, barrel assembly, and shaft assembly. It then lists 22 steps for assembly, covering installation of seals, plates, piston shoe assemblies, cam plate, springs, and other components in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...jdkskmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...prmy389342
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft. The assembly process describes 25 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...8ufjsekddm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar cat 323 d2 l excavator (prefix pjp) service repair manual (pjp000...idkdkddmd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Similar to Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001 and up).pdf (20)
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...dujkdksmdmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to position the front cover and hand tighten bolts.
4. Align the front cover and tighten the bolts. Install a new front seal and reinstall any removed components.
This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure consists of 30 steps to reinstall the parts in reverse order, noting the proper application of sealants and adjustment of bearing preload using shims. Precise alignment and cleanliness of parts is emphasized throughout.
Caterpillar Cat 330D2 L Excavator (Prefix FEX) Service Repair Manual (FEX0000...dujkdksmdmdm
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D2 L Excavator (Prefix EBP) Service Repair Manual (EBP0000...dujkdksmdmdm
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves removing 37 individual parts in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on setting the bearing preload and installing seals correctly.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
The document provides instructions for disassembling a final drive component in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the shafts, washers, bearings and gears.
3. Remove the ring gear from the sprocket housing, then disassemble the motor housing by removing bolts, shims and a coupling gear.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...dujkdksmdmdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...dujkdksmdmdm
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts, and removing mounting bolts and seals.
3. Reinstalling seals and components in reverse order, and refilling the hydraulic system. Proper cleaning, safety procedures, and use of anti-seize compound are emphasized.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...dujkdksmdmdm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have additional assistance when removing heavy components weighing over 30kg. The detailed process takes the final drive completely apart down to individual planetary gears and shafts.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...dujkdksmdmdm
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...dujkdksmdmdm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive including removing covers, gears, carriers, shafts, seals and housings. Special tools are required including link brackets and forcing bolts to remove components due to their weight, with some parts weighing up to 550kg. Detailed illustrations accompany each step to show how to disassemble the various components.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...dujkdksmdmdm
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the proper sequence for installing mounting bolts are also included.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, three planetary gear assemblies, carrier assemblies, ring gear, and other internal gears, shafts, seals and bearings. Special tools are required for pressing, pulling, and removing components. Proper lifting devices and safety precautions are noted due to the heavy weights of components ranging from 32 to 550 kg.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housings, and other components in the proper order and orientation. Bolts are tightened to the specified torque using an impact wrench. The completed swing drive is then installed on the excavator frame and filled with oil.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315D L EXCAVATOR CJN
Configuration: 315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i01219550
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor.
Reference: Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the
travel motor is 60 kg (132 lb).
1/8
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00510326
Note: During the removal of head (2) from the body of the travel motor, be careful not to
scratch or damage the mating surfaces of the components.
4. Remove socket head bolts (1).
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00510341
2/8
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00510349
6. Turn over head (2).
7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head.
8. Remove the two check valve assemblies from the head.
Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not
remove the retainer.
9. Insert a dowel rod with a small diameter into hole (X). Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
Illustration 4 g00510351
10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
Illustration 5 g00510352
11. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor.
12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port (Y). Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the body of the travel motor.
3/8
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00510353
13. Remove O-ring seal (15) from the brake piston. Remove backup ring (16) from the brake
piston.
14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake
piston.
Illustration 7 g00510356
15. Remove piston guide (19), five friction plates (20) and the four steel plates from the body of
the travel motor.
Illustration 8 g00510359
4/8
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston
guide.
Illustration 9 g00510365
Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the component's original location.
17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body
of the travel motor. Do not allow the components to fall apart.
Illustration 10 g00510502
Note: Shoe retainer (24) and piston shoe assemblies (25) are not serviced separately. Prior
to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
5/8
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00510504
19. Remove guide (27), spacer (28) and springs (29) from the barrel.
Illustration 12 g00510547
20. Remove cam plate (30) from the body of the travel motor.
Illustration 13 g00510550
21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel
motor.
6/8
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00510551
22. Remove O-ring seal (33) from the body of the travel motor.
23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 14.
Illustration 15 g00510595
24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
Illustration 16 g00510598
7/8
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 25. Remove inner race (37) from shaft (34).
Illustration 17 g00510599
26. Remove lip seal (38) from the body of the travel motor.
Illustration 18 g00510605
27. Remove two stoppers (39) and the two pistons from the body of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 17 19:18:43 UTC+0800 2020
8/8
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315D L EXCAVATOR CJN
Configuration: 315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i01706705
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
Illustration 1 g00510595
2. Install retaining ring (35) in the groove on shaft (34).
3. Install bearing (36) on shaft (34) with a press. Install the bearing until the bearing contacts
the retaining ring.
1/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 4. Install the other retaining ring on the opposite side of bearing (36).
Illustration 2 g00510598
5. Install inner race (37) on the end of shaft (34) until the inner race is seated against the
shoulder on the shaft.
Illustration 3 g00651891
(a) Body
6. Apply a thin coat of 5P-3413 Pipe Sealant on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (A) in order to install lip seal (38).
8. Install lip type seal (38) in the body of the travel motor. Install the lip seal so that the sealing
lip is facing in the direction that is shown. Make sure that the lip seal contacts the
counterbore in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
2/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
Illustration 4 g00651960
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
Illustration 5 g00510547
3/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 12. Install cam plate (30) in the body of the travel motor in the cam plate's original location.
Make sure that the two pistons and two keys (31) in the body of the travel motor engage
properly with the cam plate.
Illustration 6 g00510504
13. Install nine springs (29) in the barrel. Install spacer (28) and guide (27) on the barrel.
Illustration 7 g00878253
14. Install piston shoe assemblies (25) in the piston shoe assembly's original bores in shoe
retainer (24).
15. Apply clean hydraulic oil in the bores of the barrel and on piston shoe assemblies (25).
Install the piston shoe assemblies with the shoe retainer in the piston shoe assembly's
original bore in barrel (26).
NOTICE
Make sure that the cam plate is correctly engaged with the two pistons
in the body of the travel motor prior to installing the barrel assembly.
When the body of the travel motor is tilted to allow the installation of
the barrel assembly, the cam plate can slide off of the two pistons. The
remaining parts of the travel motor can be assembled with the cam
plate in the incorrect position.
4/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Extensive damage will result from the incorrect installation of the cam
plate. Follow the exact installation procedure to prevent damage.
16. Apply clean hydraulic oil on the sliding surfaces of the cam plate, on the piston shoe
assemblies and on the splined shaft of the travel motor.
Illustration 8 g00485953
17. Route a piece of strong string through an opening for the cam plate tension adjusters. Route
the string over the sliding surface of cam plate (30) and through the opposite opening for the
cam plate tension adjusters. Hold the string taut in order to keep cam plate (30) correctly
engaged with keys (31). Keep the string taut and position the body of the travel motor on the
body's side. Do not release the tension on the string at this time. Install barrel assembly (23)
as a unit on the shaft. Pull the string out of the body of the travel motor. It may be necessary
to pull the barrel assembly and the piston shoe assemblies away from the cam plate slightly
in order to release the string.
Illustration 9 g00651967
5/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 18. Install O-ring seal (21) and backup ring (22) on piston guide (19), as shown.
Illustration 10 g00510356
19. Place the body of the travel motor in a vertical position.
20. Apply clean hydraulic oil on five friction plates (20) and the four steel plates. Install the
plates in alternating order in the body of the travel motor. Start with a friction plate and end
with a friction plate.
21. Install piston guide (19) in the body of the travel motor until the piston guide contacts the
counterbore in the body of the travel motor.
Illustration 11 g00878297
Note: Make sure that brake piston (14) is thoroughly clean and free of dirt and debris.
22. Install O-ring seal (16). Install backup ring (15).
23. Install O-ring seal (17). Install backup ring (18).
6/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 24. Apply a thin coat of hydraulic oil on the surfaces of piston (14) which contact the body of
the travel motor. Install piston (14) in the body of the travel motor by hand. It may be
necessary to use a soft faced hammer to seat the piston correctly.
Illustration 12 g00878299
Illustration 13 g00878239
25. Install washer set (12) in piston (14), as shown.
26. Install O-ring seals (13) in the body of the travel motor, as shown.
7/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 14 g00510605
27. Install the two pistons and two stoppers (39) in the housing of the travel motor. Tighten the
stoppers to a torque of 140 ± 14 N·m (105 ± 10 lb ft).
Illustration 15 g00510351
28. Install the O-ring seals on fittings (10). Apply 5P-3413 Pipe Sealant on the threads of
fittings (10). Install the fittings in the head, as shown.
29. Install plugs (11) in the head. Tighten each plug to a torque of 15 ± 2 N·m (11 ± 1 lb ft).
Illustration 16 g00510349
8/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 17 g00510341
30. Apply a thin coat of 9S-3263 Thread Lock Compound on the threads of the two check
valves. Install the check valves in the head.
31. Install seat (7), poppet (8) and spring (9) in the head at Location (X).
32. Install O-ring seal (6) in the head, as shown.
33. Install bearing (3) in the head until the bearing contacts the counterbore in the cover.
34. Apply 1U-6396 O-Ring Assembly Compound on port plate (4). Install the port plate in the
port plate's original position on the motor cover.
35. Use a shim or shims (5) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
a. The travel motor output shaft does not rotate with an applied torque of 440 N·m
(325 lb ft) or more with the parking brake release port open.
b. The travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or
less when the parking brake release port is pressurized to 780 kPa (115 psi) with both
the inlet port and the outlet port open to the hydraulic oil tank.
Note: It may be necessary to remove head (2) several times in order to determine the correct
thickness of shim or shims (5) that are used to adjust the rolling torque of the travel motor
output shaft.
36. Apply a thin layer of 5P-0960 Molybdenum Grease on shim or shims (5). Install the shim or
shims on the head. The grease will hold the shim or shims in place during the installation of
the head. Install the head on the body of the travel motor.
9/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 18 g00510326
37. Place head (2) in the head's original position on the travel motor. Install socket head bolts
(1) that secure the head. Tighten the socket head bolts to a torque of 175 ± 18 N·m
(130 ± 13 lb ft).
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install" in this
manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 17 19:19:39 UTC+0800 2020
10/10
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315D L EXCAVATOR CJN
Configuration: 315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i03524320
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod M16 by 381mm 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/3
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g00651795
2. Install a new O-ring seal (5) . Apply clean hydraulic oil on O-ring seal (5) .
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown. The weight of travel motor (4)
is approximately 57 kg (125 lb).
Illustration 3 g00944825
2/3
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 4. Carefully install travel motor (4) on Tooling (A) . Slide travel motor (4) into the final drive.
5. Install bolt (2A) that secures travel motor (4) to the final drive.
6. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
7. Install bolts (2) .
8. Connect hose assemblies (3) and (1) .
9. Fill the final drive with oil. Refer to Operation and Maintenance Manual, "Lubricant
Viscosities" for the proper oil viscosity. Refer to Operation and Maintenance Manual, "Final
Drive Oil Level - Check" for the correct filling procedure.
10. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
11. Obtain a hydraulic oil sample from the main S·O·S port. Refer to Operation and
Maintenance Manual, "Sampling Interval and Location of Sampling Valve" for the correct
location.
12. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system. Refer to Contamination
Control Guideline, SEBF8447 for further information.
End By: Install the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 17 19:20:35 UTC+0800 2020
3/3
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315D L EXCAVATOR CJN
Configuration: 315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g00489826
Typical Example
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
Illustration 3 g00712737
2/3
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 4 g00712749
4. Use Tooling (C) in order to remove the final drive from the frame.
5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 17 19:21:31 UTC+0800 2020
3/3
315D L Excavator CJN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP48...
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...