1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly involves removing 21 components including gears, shafts, seals, and housings. Special tools are required.
3) Assembly requires determining the proper shim thickness to set the rolling torque and installing components in reverse order. Cleanliness and applying oil to parts is important.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...tuzhiyou2
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next, it describes removing individual components from the final drive including covers, gears, shafts, seals and housings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next it describes removing individual components from the final drive including covers, gears, shafts, seals and housings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...lituo39419496
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next, it describes removing individual components from the final drive including covers, plates, gears, shafts, seals and bearings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...rishang96299
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...tuzhiyou2
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next, it describes removing individual components from the final drive including covers, gears, shafts, seals and housings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly.
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next it describes removing individual components from the final drive including covers, gears, shafts, seals and housings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...lituo39419496
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. It begins with removing the final drive assembly from the excavator. Next, it describes removing individual components from the final drive including covers, plates, gears, shafts, seals and bearings. The assembly section provides instructions for installing these components in reverse order and includes steps for determining the proper shim thickness to set the rolling torque. The summary is provided in 3 sentences or less.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...rishang96299
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...kubei069369925
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...fuusejkddmmd3e
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...dujkdksmdmdm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...fujkse9didkke3
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations accompany each step to show how to disassemble and reassemble the components.
3. Special attention is drawn to cleaning parts and applying threadlocker during installation to prevent contamination and ensure proper component life.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
Caterpillar Cat 330D L Excavator (Prefix NBD) Service Repair Manual (NBD00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...fujkse9didkke3
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fujkse9didkke3
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...fujkse9didkke3
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, housings and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have assistance when removing heavier components weighing over 30 kg.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...fujkse9didkke3
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fujkse9didkke3
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the fully assembled piston motor and fan assembly onto mounting brackets on the excavator.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
More Related Content
Similar to Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001 and up).pdf
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual Instant D...kubei069369925
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...fuusejkddmmd3e
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 27 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring pressure.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...dkdmidkkdk
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...dujkdksmdmdm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It lists 28 steps for disassembly, which include removing bolts, valves, seals, bearings, pistons, and other components. It then lists 25 steps for reassembly in reverse order, noting to clean parts thoroughly, replace all seals and gaskets, and apply a light film of oil before assembling components. Precautions are provided for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 315C and 315C L Excavator models. The disassembly process involves 27 steps to remove components like the traction control valve, travel motor, piston motor, brake pack, pistons, and bearings. The assembly process reverses the disassembly with 23 steps and cautions to clean parts, replace seals and gaskets, apply lubricant, and heat/cool components for proper installation. Proper tooling and following all steps is important to prevent damage during disassembly and assembly.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, springs and plates. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing parts with spring forces.
Similar to Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001 and up).pdf (8)
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...fujkse9didkke3
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations accompany each step to show how to disassemble and reassemble the components.
3. Special attention is drawn to cleaning parts and applying threadlocker during installation to prevent contamination and ensure proper component life.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
Caterpillar Cat 330D L Excavator (Prefix NBD) Service Repair Manual (NBD00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...fujkse9didkke3
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fujkse9didkke3
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...fujkse9didkke3
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, housings and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have assistance when removing heavier components weighing over 30 kg.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...fujkse9didkke3
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fujkse9didkke3
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the fully assembled piston motor and fan assembly onto mounting brackets on the excavator.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
This document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing over 30 individual parts in a specific sequence, including gears, shafts, bearings, seals, and housing components. Special tools are required to remove some parts. Proper lifting equipment and safety precautions are needed due to the heavy weights involved, up to approximately 550 kg for the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It outlines 28 steps for disassembly, removing components like the head, brake piston, plates and discs. It then outlines 13 steps for assembly, including installing seals, bearings, springs and ensuring proper placement of parts. Cleanliness is emphasized throughout the process.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
Caterpillar Cat 330C L Excavator (Prefix JAB) Service Repair Manual (JAB00001...fujkse9didkke3
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
3) It then describes 29 steps for assembling the travel motor, providing notes on cleaning, lubrication, and proper installation of components like O-rings, pistons, seals, and bolts.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models. It outlines 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then lists 13 steps for reassembling the motor and installing components in the reverse order of disassembly while ensuring cleanliness and applying thread lock compounds as needed.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CFB
Configuration: 315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01960779
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Repair Stand 1
B 1U-7600 Slide Hammer 1
C 138-7575 Link Brackets 3
D 154-6181 Forcing Screw 2
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive- Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Dispose of all fluids according to local regulations and mandates.
NOTICE
Failure to properly assemble parts or failure to follow established
procedures can lead to damage of the parts and assembly.
To avoid damage to parts, always identify and mark the parts so that
they can be installed in the same location. Ensure that gear surfaces
align. Never force parts during assembly.
Illustration 1 g00777501
1. Install the final drive assembly on Tooling (A) .
Illustration 2 g01018685
2/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Remove bolts (1). Remove plugs (2) and the O-ring seals from cover (3). Remove cover
(3) .
Illustration 3 g00777515
3. Use Tooling (B) in order to remove plate (4) .
Illustration 4 g00777542
4. Remove carrier assembly (5) from the main housing. The weight of the carrier assembly is
approximately16 kg (35 lb).
3/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00777548
5. Remove spacer (6) .
Illustration 6 g00777570
6. Use a suitable punch and a hammer to install spring pin (7) into planetary shaft (8) .
Illustration 7 g01021689
4/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 7. Remove planetary shaft (8). Remove spring pin (7). Remove thrust washers (9). Remove
planetary gear (11) and bearing (10) .
8. Repeat Steps 6 and 7 in order to remove the other two planetary gears from the carrier.
Illustration 8 g00777624
9. Remove gear (12) .
Illustration 9 g00777626
10. Remove gear (13). Remove spacer (14) .
5/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g00777631
11. Use Tooling (C) and a suitable lifting device in order to remove carrier assembly (15). The
weight of carrier assembly (15) is approximately 30 kg (65 lb).
Illustration 11 g01021690
12. Use a suitable punch and a hammer to install spring pin (16) into planetary shaft (17) .
Illustration 12 g01021692
6/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 13. Remove spring pin (16) from planetary shaft (17). Remove thrust washers (18), bearings
(19) and gear (20) from the carrier assembly.
Illustration 13 g01018688
14. Remove bolts (21) .
Illustration 14 g00778413
15. Use Tooling (D) in order to push gear (22) from the upper housing.
7/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00778461
16. Remove gear (22). Four dowel pins (23) will stay with the gear.
Illustration 16 g00778471
17. Use a suitable press in order to remove dowel pins (23) .
Illustration 17 g01018689
18. Remove shim (24) and washer (25) .
8/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g01018690
19. Separate housing (26) from housing (27) .
Illustration 19 g01018692
20. Remove Duo-cone seal gp (28) from housing (27) .
9/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g01018693
21. Remove Duo-cone seal gp (29) and bearings (30) from housing (26) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 2 23:26:14 UTC+0800 2020
10/10
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CFB
Configuration: 315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01961218
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Repair Stand 1
C 138-7575 Link Brackets 3
D 126-3994 Seal Installer 1
E
1U-9895 Crossblock 1
5F-7369 Leg 2
5P-4808 Cap 2
3H-0465 Plate 4
1B-4207 Nut 2
F 6V-2012 Depth Micrometer 1
G 169-0503 Installation Kit 1
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01021697
1. Place housing (27) on Tooling (A) .
2. Use Tooling (G) in order to clean the Duo-cone seal gp prior to installation. Use Tooling
(D) in order to install Duo-cone seal gp (28) into housing (27) .
Illustration 2 g01018693
3. Install bearings (30) into housing (26). Use Tooling (D) in order to install Duo-cone seal gp
(29) into housing (26).
2/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g01018690
4. Install Tooling (C) to housing (26). Use Tooling (C) and a suitable lifting device in order to
install housing (26) onto housing (27) .
Illustration 4 g01018688
5. Install gear (22). Install bolts (21) in order to hold the two housings together. This is
necessary in order to transport the housings to the press.
Note: The following steps are necessary in order to determine the proper shim or shims
needed to set the rolling torque.
3/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g01018688
a. Set the main housing assembly in a suitable press. Remove bolts (21). Remove gear
(22) .
Illustration 6 g01021714
b. Install Tooling (E). Use a suitable press in order to apply the load of 4000 kg (8818
lb). Rotate the housing in order to seat bearings (30). Reduce the load to 1000 ± 100
kg (2204 ± 220 lb).
4/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 7 g01018888
c. Maintain the load pressure of 1000 ± 100 kg (2204 ± 220 lb). Use Tool (F) in order to
obtain Measurement (A). Record the measurement.
Illustration 8 g00781842
d. Use Tooling (F) in order to obtain Measurement (B) on gear (22). Record the
measurement.
5/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 9 g00781847
Illustration 10 g01018689
e. Measure the thickness of washer (25). Record the measurement.
f. Install washer (25). Install the required shims. The shim thickness is determined by
subtracting Dimension (A) from Dimension (B) and subtractingDimension (C). This
thickness has a tolerance of ± 0.050 mm ( ± 0.0020 inch). If two shims are required,
install the thinner shim next to gear (22) .
6/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 11 g00782429
6. Install gear (22) and pins (23). Install bolts (21). Tighten bolts (21) to a torque of 270 ± 40
N·m (199 ± 30 lb ft).
Illustration 12 g01021692
7. Install bearings (19) and gear (20). Install thrust washers (18). Install planetary shaft (17)
and spring pin (16) .
Illustration 13 g01021690
7/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 8. Use a suitable punch and a hammer in order to drive spring pin (16) into planetary shaft
(17) .
Illustration 14 g00782239
Stake marks on each side of spring pin (16)
(D) Measurement of 1.5 mm (0.06 inch) from outside diameter
9. Use a suitable punch in order to peen planetary shaft (17) on each side of spring pin (16).
Each stake mark should be approximately 1.5 mm (0.06 inch) from the outside diameter of
the spring pin.
10. Repeat Steps 7 through 9 in order to install the other two planetary gears into the carrier.
Illustration 15 g00777631
8/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 11. Use Tooling (C) and a suitable lifting device in order to install carrier assembly (15). The
weight of carrier assembly (15) is approximately 30 kg (65 lb).
Illustration 16 g00777626
12. Install spacer (14). Install gear (13).
Illustration 17 g00777624
13. Install gear (12) .
9/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 18 g01021689
14. Install planetary gear (11) and bearing (10). Install thrust washers (9). Install planetary shaft
(8). Install spring pin (7) .
Illustration 19 g00782239
Stake marks on each side of spring pin (7)
(D) Measurement of 1.5 mm (0.06 inch) from outside diameter
15. Use a suitable punch in order to peen shaft (8) on each side of spring pin (7). Each stake
mark should be approximately 1.5 mm (0.06 inch) from the outside diameter of the spring
pin.
16. Repeat Steps 14 and 17 in order to install the other two planetary gears into the carrier.
10/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g00777548
17. Install spacer (6) .
Illustration 21 g00777542
18. Install carrier assembly (5) into the main housing. The weight of carrier assembly (5) is
approximately 16 kg (35 lb).
Illustration 22 g00782448
11/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 19. Install plate (4) .
Illustration 23 g01018685
20. Install cover (3). Install bolts (1). Tighten bolts (1) to a torque of 105 ± 20 N·m (77 ± 15 lb
ft). Install plugs (2) and the O-ring seals. Tighten plugs (2) to a torque of 80 ± 10 N·m (59 ±
7 lb ft).
End By: Install the final drive. Refer to Disassembly and Assembly, "Final Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 2 23:27:10 UTC+0800 2020
12/12
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Eng...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR CFB
Configuration: 315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01961382
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
C 9S-3263 Thread Lock Compound 1
1. Make sure that the mating surfaces of the final drive and the undercarriage frame are
thoroughly clean and free of dirt and debris prior to assembly.
2. Check the condition of the O-ring seals that are used in the ends of the tube assemblies.
Check the condition of the O-ring seals that are used in the ends of the hose assemblies. If
the O-ring seals are worn or damaged, use new parts for replacement.
1/4
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00486987
3. Fasten Tooling (A) and a suitable lifting device to final drive (7). Carefully, put the final
drive in position on the undercarriage frame.
Illustration 2 g00486988
4. Apply Tooling (C) on the threads of bolts (8). Install bolts (8) that hold the final drive to the
undercarriage frame. Tighten bolts (8) evenly.
5. Install plugs (9) in the forcing bolt holes.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
2/4
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/11/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...