This document provides disassembly instructions for a 314C excavator final drive and travel motor. It lists required tools and outlines 16 steps to disassemble the components, including removing covers, plates, gears, seals, pistons, springs and other parts. Personal injury warnings are provided throughout regarding releasing pressures and spring forces. The goal is to disassemble the final drive and travel motor into individual parts for cleaning or replacement.
Caterpillar cat 314 c lcr excavator (prefix kja) service repair manual (kja00...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and other components of a 314C excavator. It lists required tools and outlines over 30 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like released spring forces and hot or pressurized fluids.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...jfdskekdmme
This document provides disassembly instructions for excavator models 314C, 314C CR, and 314C LCR. It describes how to disassemble components of the final drive, travel motor, counterbalance valve, and other systems. The instructions are detailed, listing each part and step in the disassembly process. Required tools are provided at the beginning. Safety notices are included throughout to warn of hazards like stored energy in springs.
Caterpillar cat 314 c excavator (prefix sny) service repair manual (sny00001 ...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of 314C and 314C CR excavators. It outlines 16 steps to disassemble the final drive which include removing fittings, bolts, and valves. It then details 14 steps to disassemble the counterbalance valve which involve removing springs, seals, pistons, and spools. Finally, it lists 10 steps to disassemble the travel motor which include removing seals, pistons, plates and barrel assemblies. Safety notices are included throughout to warn of hazards such as released pressures and falling/lifting heavy components.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like parts propelled by springs, hydraulic pressure, and heavy component weights. Required tools are listed in a table at the beginning.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of an excavator model 313D2. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, piston assemblies, gears, seals and other parts. Tools required include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers and other specialized tools. Safety notices are provided to properly release pressures and contain fluids.
Caterpillar cat 314 d lcr excavator (prefix byj) service repair manual (byj00...soeldksejdksem
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 314D CR and 314D LCR excavator. It lists 17 required tools and gives detailed step-by-step instructions to disassemble each component. Some key steps include draining fluids, removing covers and plates, using pullers to remove bearings, and noting part locations for reassembly. Safety notices are provided regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for disassembling each component. Personal safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs or releasing hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for repair or replacement of parts.
Caterpillar cat 314 c lcr excavator (prefix kja) service repair manual (kja00...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and other components of a 314C excavator. It lists required tools and outlines over 30 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like released spring forces and hot or pressurized fluids.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...jfdskekdmme
This document provides disassembly instructions for excavator models 314C, 314C CR, and 314C LCR. It describes how to disassemble components of the final drive, travel motor, counterbalance valve, and other systems. The instructions are detailed, listing each part and step in the disassembly process. Required tools are provided at the beginning. Safety notices are included throughout to warn of hazards like stored energy in springs.
Caterpillar cat 314 c excavator (prefix sny) service repair manual (sny00001 ...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of 314C and 314C CR excavators. It outlines 16 steps to disassemble the final drive which include removing fittings, bolts, and valves. It then details 14 steps to disassemble the counterbalance valve which involve removing springs, seals, pistons, and spools. Finally, it lists 10 steps to disassemble the travel motor which include removing seals, pistons, plates and barrel assemblies. Safety notices are included throughout to warn of hazards such as released pressures and falling/lifting heavy components.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like parts propelled by springs, hydraulic pressure, and heavy component weights. Required tools are listed in a table at the beginning.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of an excavator model 313D2. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, piston assemblies, gears, seals and other parts. Tools required include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers and other specialized tools. Safety notices are provided to properly release pressures and contain fluids.
Caterpillar cat 314 d lcr excavator (prefix byj) service repair manual (byj00...soeldksejdksem
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 314D CR and 314D LCR excavator. It lists 17 required tools and gives detailed step-by-step instructions to disassemble each component. Some key steps include draining fluids, removing covers and plates, using pullers to remove bearings, and noting part locations for reassembly. Safety notices are provided regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for disassembling each component. Personal safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs or releasing hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for repair or replacement of parts.
Caterpillar cat 314 c excavator (prefix kja) service repair manual (kja00001 ...fjkskefksmeme
This document provides disassembly instructions for the final drive, travel motor, and related components of a 314C excavator. It outlines over 15 steps to disassemble the final drive, including removing covers, gears, and bearing assemblies. It also details over 15 steps to disassemble the travel motor, such as removing piston assemblies, seals, and friction plates. Safety notices are provided throughout to warn of hazards like released spring forces or hot/pressurized fluids.
Caterpillar cat 314 c cr excavator (prefix kja) service repair manual (kja000...fjkskefksmeme
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 314C excavator. It lists the required tools and gives step-by-step procedures for removing components such as sprockets, fittings, plates, seals, springs, pistons, and housings. Safety notices are included regarding releasing pressures and contained fluids. Detailed illustrations supplement the text.
Caterpillar cat 314 c excavator (prefix pca) service repair manual (pca00001 ...dikdkskdmmd
This document provides instructions for disassembling various components of a 314C excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists over 20 detailed steps for removing parts like sprockets, fittings, valves, pistons, springs, and plates. Safety notices are included throughout to warn of hazards like stored energy in springs and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...dikskekmdmdm
This document provides disassembly instructions for excavator models 314C, 314C CR, and 314C LCR. It describes how to disassemble components of the final drive, travel motor, and counterbalance valve. The process involves removing covers, plates, gears, seals, springs, and other parts. Detailed illustrations and cautions are provided to guide mechanics through each step safely.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...jfdjskmdmme
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists over 20 detailed steps for removing parts like sprockets, fittings, valves, pistons, springs, and plates. Safety notices are included throughout to warn of hazards like stored energy in springs and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 314 c excavator (prefix pca) service repair manual (pca00001 ...fdhjsekdme
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and other systems. The summary is as follows:
1) Detailed step-by-step instructions are given to disassemble components like the final drive, travel motor, counterbalance valve, and related systems of an excavator.
2) Over 30 illustrations are included to supplement the text instructions.
3) Safety notices are provided throughout to warn of hazards like stored energy in springs or hot/pressurized fluids.
John deere 230 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 sprayer attachment service repair manualfhsjejkdm
This technical manual provides specifications and information for servicing a John Deere 200 Sprayer Attachment. It includes sections on general specifications for the vehicle and sprayer components, repair information such as torque values, lubricant specifications, and locations for identification numbers. It also describes operational checkout procedures to test the sprayer system.
John deere 113 172 clipper service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, including engine details, fuel and oil requirements, ignition components, and dimensions for the different models. Safety guidelines are also outlined for operating the equipment safely.
John deere 110 g, 210g, 240g 260g trimmer clutters service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreach and kickback, and not modify machines without authorization.
John deere 54 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and safety information. The manual is intended for experienced technicians and covers engine, fuel, electrical, power train, steering, brake, and mower deck systems. Safety messages in the introduction emphasize the importance of following proper safety precautions when working on equipment.
John deere 51 & 246 rotary brooms service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission oils, and specifications for rotary mowers and snowblowers. The manual aims to ensure technicians have the correct information to service equipment properly and safely.
John deere 48, 450, 550 & 660 rotary tillers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48, 50, 54, 60, 72, 76, 160, 172, 261 & 272 rotary mowers serv...fhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and operational testing for the engine, fuel system, electrical system, power train, steering, brakes, mower deck, and other components. Safety messages are presented throughout and fastener torque specifications are provided. The manual is intended for experienced technicians and is part of John Deere's total product support program.
John deere 47, 59 & 359 snowblowers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 46, 49 & 50 snowthrowers service repair manualfhsjejkdm
This technical manual provides information for experienced technicians on inspecting, disassembling, and assembling various John Deere lawn and grounds care equipment including rotary mowers, snowblowers, snowthrowers, post hole diggers, rotary tillers, and rotary brooms with either 2000 or 540 RPM PTO. The manual is organized by equipment type and covers sections like safety procedures, fluid handling, battery handling, and service procedures.
Clark gph 50 forklift service repair manualfhsjejkdm
This document provides guidance on planned maintenance procedures for lift trucks. It emphasizes the importance of routine inspections and lubrication for long life and trouble-free operation. The summary outlines key steps in the planned maintenance process, including:
1. Performing a visual inspection of the entire lift truck, checking for issues like leaks, loose fasteners, and worn/damaged components.
2. Using a planned maintenance report form to document inspections and any needed repairs.
3. Testing functions like the starting system, gauges, controls, brakes and steering to ensure proper operation.
4. Inspecting and lubricating specific components, like the engine, hydraulic and electrical systems, wheels/
More Related Content
Similar to Caterpillar cat 314 c lcr excavator (prefix kja) service repair manual (kja00001 and up)
Caterpillar cat 314 c excavator (prefix kja) service repair manual (kja00001 ...fjkskefksmeme
This document provides disassembly instructions for the final drive, travel motor, and related components of a 314C excavator. It outlines over 15 steps to disassemble the final drive, including removing covers, gears, and bearing assemblies. It also details over 15 steps to disassemble the travel motor, such as removing piston assemblies, seals, and friction plates. Safety notices are provided throughout to warn of hazards like released spring forces or hot/pressurized fluids.
Caterpillar cat 314 c cr excavator (prefix kja) service repair manual (kja000...fjkskefksmeme
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 314C excavator. It lists the required tools and gives step-by-step procedures for removing components such as sprockets, fittings, plates, seals, springs, pistons, and housings. Safety notices are included regarding releasing pressures and contained fluids. Detailed illustrations supplement the text.
Caterpillar cat 314 c excavator (prefix pca) service repair manual (pca00001 ...dikdkskdmmd
This document provides instructions for disassembling various components of a 314C excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists over 20 detailed steps for removing parts like sprockets, fittings, valves, pistons, springs, and plates. Safety notices are included throughout to warn of hazards like stored energy in springs and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...dikskekmdmdm
This document provides disassembly instructions for excavator models 314C, 314C CR, and 314C LCR. It describes how to disassemble components of the final drive, travel motor, and counterbalance valve. The process involves removing covers, plates, gears, seals, springs, and other parts. Detailed illustrations and cautions are provided to guide mechanics through each step safely.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...jfdjskmdmme
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists over 20 detailed steps for removing parts like sprockets, fittings, valves, pistons, springs, and plates. Safety notices are included throughout to warn of hazards like stored energy in springs and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 314 c excavator (prefix pca) service repair manual (pca00001 ...fdhjsekdme
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and other systems. The summary is as follows:
1) Detailed step-by-step instructions are given to disassemble components like the final drive, travel motor, counterbalance valve, and related systems of an excavator.
2) Over 30 illustrations are included to supplement the text instructions.
3) Safety notices are provided throughout to warn of hazards like stored energy in springs or hot/pressurized fluids.
Similar to Caterpillar cat 314 c lcr excavator (prefix kja) service repair manual (kja00001 and up) (6)
John deere 230 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 sprayer attachment service repair manualfhsjejkdm
This technical manual provides specifications and information for servicing a John Deere 200 Sprayer Attachment. It includes sections on general specifications for the vehicle and sprayer components, repair information such as torque values, lubricant specifications, and locations for identification numbers. It also describes operational checkout procedures to test the sprayer system.
John deere 113 172 clipper service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, including engine details, fuel and oil requirements, ignition components, and dimensions for the different models. Safety guidelines are also outlined for operating the equipment safely.
John deere 110 g, 210g, 240g 260g trimmer clutters service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreach and kickback, and not modify machines without authorization.
John deere 54 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and safety information. The manual is intended for experienced technicians and covers engine, fuel, electrical, power train, steering, brake, and mower deck systems. Safety messages in the introduction emphasize the importance of following proper safety precautions when working on equipment.
John deere 51 & 246 rotary brooms service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission oils, and specifications for rotary mowers and snowblowers. The manual aims to ensure technicians have the correct information to service equipment properly and safely.
John deere 48, 450, 550 & 660 rotary tillers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48, 50, 54, 60, 72, 76, 160, 172, 261 & 272 rotary mowers serv...fhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and operational testing for the engine, fuel system, electrical system, power train, steering, brakes, mower deck, and other components. Safety messages are presented throughout and fastener torque specifications are provided. The manual is intended for experienced technicians and is part of John Deere's total product support program.
John deere 47, 59 & 359 snowblowers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 46, 49 & 50 snowthrowers service repair manualfhsjejkdm
This technical manual provides information for experienced technicians on inspecting, disassembling, and assembling various John Deere lawn and grounds care equipment including rotary mowers, snowblowers, snowthrowers, post hole diggers, rotary tillers, and rotary brooms with either 2000 or 540 RPM PTO. The manual is organized by equipment type and covers sections like safety procedures, fluid handling, battery handling, and service procedures.
Clark gph 50 forklift service repair manualfhsjejkdm
This document provides guidance on planned maintenance procedures for lift trucks. It emphasizes the importance of routine inspections and lubrication for long life and trouble-free operation. The summary outlines key steps in the planned maintenance process, including:
1. Performing a visual inspection of the entire lift truck, checking for issues like leaks, loose fasteners, and worn/damaged components.
2. Using a planned maintenance report form to document inspections and any needed repairs.
3. Testing functions like the starting system, gauges, controls, brakes and steering to ensure proper operation.
4. Inspecting and lubricating specific components, like the engine, hydraulic and electrical systems, wheels/
Clark gp127 e forklift service repair manualfhsjejkdm
This document provides instructions and safety guidelines for Clark lift truck maintenance personnel. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Specific safety practices include properly jacking, blocking and lifting trucks, following electrical safety procedures, and ensuring only trained personnel conduct maintenance.
Clark gp127 forklift service repair manualfhsjejkdm
This document provides instructions and safety precautions for Clark industrial lift truck maintenance personnel. It outlines recommended safe maintenance practices including properly jacking, blocking and towing trucks. The document instructs technicians to only perform maintenance if trained and authorized, using manufacturer procedures and recommendations. Technicians are advised to take safety precautions such as wearing protective equipment, disconnecting power sources, and avoiding fire hazards.
Clark gex20 30 forklift service repair manualfhsjejkdm
The document provides instructions and safety information for maintaining industrial trucks. It discusses identifying and understanding safety signs, recommended safe maintenance practices, and general shop safety precautions. The safe maintenance practices section lists 20 points covering proper maintenance procedures, qualifications of maintenance personnel, personal protective equipment, safety checks, fuel and electrical system handling, inspection of truck components, and using proper replacement parts.
Clark gcs standard forklift service repair manualfhsjejkdm
- This document is a service manual intended for CLARK dealers providing maintenance and repair information for CLARK lift trucks.
- It contains general safety practices and precautions for working on lift trucks, identifying important safety signs and messages, and provides model identification information.
- Technicians are instructed to read all safety information and follow proper procedures to prevent injuries when servicing lift trucks.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314C EXCAVATOR KJA
Configuration: 314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
314C Excavator Excavator Systems
Media Number -RENR6613-05 Publication Date -01/03/2017 Date Updated -13/03/2017
i04126149
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
S/N - KJA277-UP
S/N - PCA1658-UP
S/N - SNY499-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
C 8T-6699 Bolts 2
D
1P-0074 Slide Hammer Puller Gp 1
4C-5666 Threaded Adapter 1
123-6702 Backlash Gauge Gp 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
Start By:
1/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. a. Remove the final drive and the travel motor. Refer to Disassembly and Assembly Manual ,
"Final Drive and Travel Motor - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor. The weight of the sprocket is
approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
2/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 1 g00940682
4. Use Tooling (A) and a suitable lifting device to position the final drive and the travel motor
onto Tooling (B). The combined weight of the final drive and travel motor is approximately
170 kg (375 lb).
5. Drain the oil from the final drive into a suitable container for storage or for disposal. Refer
to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the final
drive.
6. Remove fittings (1). Remove fittings (2) from traction control valve (3).
7. Remove nine bolts (4) that secure traction control valve (3) to the final drive.
8. Use two persons to remove traction control valve (3) from the final drive. The weight of
travel brake valve (3) is approximately 27 kg (60 lb).
3/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 2 g00940716
9. Remove valve plate (5) and O-ring seal (6).
Illustration 3 g01405139
10. Use Tooling (D) to remove bearing (7).
Disassembly of the Counterbalance Valve
Illustration 4 g01405725
4/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 5 g01405227
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Position the counterbalance valve, as shown. Remove plug (8) and adapter (9).
2. Remove spring (10) and spool (11).
Illustration 6 g01405232
5/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 3. Remove relief valve assemblies (12).
Illustration 7 g01405243
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove seat (13). Seat (13) is pressed onto valve (17). Use new parts if seat (13) or valve
(17) is damaged. Do not disassemble these components. Make sure that you reuse the other
component.
5. Remove backup ring (14) and O-ring seal (15).
6. Remove O-ring seal (22).
7. Remove nut (20).
8. Remove screw (27).
9. Remove stopper (26). Remove backup ring (19) and O-ring seal (18) from stopper (19).
10. Remove valve (21), piston (25), and spring (16) from the housing.
11. Remove backup ring (23) and O-ring seal (24) from piston (25).
6/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 8 g01405284
Illustration 9 g01405299
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove covers (28) and the O-ring seals.
13. Remove springs (29), guides (30), and spool assembly (31).
7/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 10 g01405345
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
14. Remove valve (32), spring (33), and ball (34) from one end of spool (35). Repeat for the
other end of spool (35).
Illustration 11 g01405633
8/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
15. Remove plug (36), spring (38), and piston (39) from both sides of the housing assembly.
16. Remove O-ring seal (37) from each plug (36).
Note: Remove the remaining allen head bolts from the housing assembly for cleaning
purposes, if necessary. Each allen head bolt has an O-ring seal. Check the O-ring seal for
wear or for damage. Replace the O-ring seal, if necessary.
Disassembly of the Travel Motor
Illustration 12 g01405794
1. Remove O-ring seal (40) and springs (41).
9/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 13 g01405828
2. Install Tooling (C) onto piston assembly (42). Use Tooling (C) and a suitable prybar to
remove piston assembly (42) from body (43).
Illustration 14 g01405855
3. Remove O-ring seals (45) and (46) from piston assembly (42). Remove backup rings (44)
and (47) from piston assembly (42).
10/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 15 g01405867
4. Use suitable drivers or a suitable lever to remove guide assembly (48).
Illustration 16 g01405885
5. Remove O-ring seal (49) and backup ring (50) from guide assembly (48).
11/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 17 g01406117
6. Remove four separator plates (51) and four friction plates (52). Note the alternating order of
separator plates (51) and friction plates (52) for assembly purposes.
Note: Do not allow the components of barrel assembly (53) to come apart while you
remove barrel assembly (53). The components of barrel assembly (53) must be reinstalled
into the original positions.
Note: Oil will drain from the final drive. Place a suitable container under the final drive for
storage or disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for
the fluid capacity of the final drive.
7. Position the final drive horizontally.
8. Remove barrel assembly (53).
12/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 18 g01406180
Note: Mark the component locations for assembly purposes before you disassemble barrel
assembly (53).
9. Remove piston assemblies (54) and retainer (55) from barrel assembly (53).
Illustration 19 g01406210
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Remove retainer (56), spacer (57), and springs (58) from barrel assembly (53).
13/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 20 g01406263
11. Put location marks on cam plate (59) for assembly purposes. Make sure that the thick end of
cam plate (59) is adjacent to the opening that is across body (43). Remove cam plate (59).
Illustration 21 g01406329
Illustration 22 g01406338
14/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove piston (60) and spring (62).
13. Remove key (61).
Disassembly of the Final Drive
Illustration 23 g01406376
1. Use a suitable lifting device to position the final drive on Tooling (B), as shown. The weight
of the final drive is approximately 200 kg (441 lb).
2. Remove plugs (63). Remove the O-ring seals from plugs (63). Check the O-ring seals for
wear or for damage. Replace the O-ring seals, if necessary.
3. Remove bolts (65). Remove cover (64).
15/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 24 g01406386
4. Raise the temperature of bolts (66) in order to loosen the thread sealant.
5. Remove bolts (66) and plate (67).
Illustration 25 g01406397
6. Remove sun gear (68).
16/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 26 g01406400
7. Attach Tooling (A) and a suitable lifting device to carrier assembly (69). Remove carrier
assembly (69), planetary gear assembly (70), and bearing assembly (71) as a unit.
Illustration 27 g01406789
8. Remove planetary gear (70) and bearing assembly (71) from carrier assembly (69). Remove
the remaining planetary gears (70) and bearings (71).
Illustration 28 g01406822
9. Remove sun gear (72).
17/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. 10. Raise the temperature of bolts (73) in order to loosen the thread sealant. Remove bolts (73).
Remove plate (74).
Illustration 29 g01406850
11. Remove retaining ring (75) from sun gear (72). Check retaining ring (75) for wear or for
damage. Replace retaining ring (75), if necessary.
Illustration 30 g01406853
12. Remove planetary gear (76).
18/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 31 g01406875
13. Remove bearing (77), race (78), and thrust washer (79).
14. Repeat Steps 12 and 13 in order to remove the remaining planetary gear assemblies.
Illustration 32 g01406882
15. Remove bolt (80) and plate (81).
19/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 33 g01406885
Illustration 34 g01406886
16. Use Tooling (H) to remove nut (82).
Illustration 35 g01406906
17. Install Tooling (A) and a suitable lifting device to housing (83). The weight of housing (83)
is approximately 35 kg (77 lb).
18. Remove housing (83) from body assembly (84).
20/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 36 g01406912
19. Remove Duo-Cone Seal Gp seal (85) from the body assembly. Remove the Duo-Cone Seal
Gp seal from the housing.
Illustration 37 g01407100
20. Remove both bearings (86) from housing (83).
21/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 38 g01407089
21. Remove both bearings (87) from housing (83).
Illustration 39 g01407115
22. Position body assembly (84) horizontally. Remove shaft assembly (88), the bearing, and the
retaining ring.
22/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 40 g01407144
23. Use Tooling (G) to remove retaining ring (89) from shaft assembly (88).
Illustration 41 g01407161
24. Use Tooling (E), Tooling (F), and a suitable press to remove bearing (90).
Illustration 42 g01407166
25. Remove lip seal (91) from the body assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 2 00:00:27 UTC+0800 2020
23/23
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 30...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314C EXCAVATOR KJA
Configuration: 314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
314C Excavator Excavator Systems
Media Number -RENR6613-05 Publication Date -01/03/2017 Date Updated -13/03/2017
i07269885
Final Drive and Travel Motor - Assemble
SMCS - 4050-016; 4351-016
S/N - KJA277-UP
S/N - PCA1658-UP
S/N - SNY499-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
K 1U-7558 Mounting Adapter Gp(1)
1
L - Loctite 271 -
M - Loctite High Flex GM -
N 169-0503 Installation Kit 1
P 1U-6434 Duo-Cone Seal Installer As 1
1/24
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Q 4C-3761 C-Clamp 2
R FT-2766 Rolling Torque Bar 1
S - Loctite 272 -
(1)
The bent plates for the mounting adapter may be modified so that the mounting adapter can be assembled to the
housing.
Assembly Procedure for the Final Drive
Illustration 1 g01407166
1. Use Tooling (E) to install lip seal (91) into the body assembly.
Illustration 2 g01407561
2. Use Tooling (E), Tooling (F), and a suitable press to install bearing assembly (90) onto shaft
assembly (88).
2/24
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Illustration 3 g01407144
3. Use Tooling (G) to install retaining ring (89) on shaft assembly (88).
Illustration 4 g01407580
4. Use a suitable soft faced hammer to install shaft assembly (88) into body assembly (84).
Illustration 5 g01407608
3/24
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064...
2020/6/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...