This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It outlines 32 steps to disassemble these components, including removing covers, plates, gears, seals, pistons, springs and other parts. Safety notices are included to warn of potential injuries from parts propelled by springs or hot/pressurized fluids. Required tools are listed.
The document provides instructions for disassembling components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve. It lists required tools and safety precautions. The multi-step process includes draining fluids, removing covers, plates, seals, springs, and other parts. Detailed illustrations accompany each step to ensure correct disassembly and reassembly of components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, barrel assembly, piston assemblies, gears, seals, and other parts. Safety notices are included to warn of hazards like fluids, springs, and heavy components. Required tools are listed.
The document provides instructions for disassembling various components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve. It lists required tools and safety precautions. The multi-step process includes draining fluids, removing covers, plates, seals, springs, and other parts. Detailed illustrations accompany each step to ensure correct disassembly and proper reinstallation of components.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing springs or draining fluids. The goal is to disassemble the major components into their individual parts to prepare for cleaning, inspection or repair.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Safety notices are included throughout to warn of potential injuries from parts propelled by springs or releasing pressurized fluids. Required tools are listed in a table at the beginning.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing pressurized components or springs. The goal is to disassemble the major assemblies into their individual parts to prepare for cleaning, inspection or repair.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists 19 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized fluids. Dismantling requires specialty tools like pullers, wrenches, and pliers.
Caterpillar cat 313 f lgc excavator (prefix gjd) service repair manual (gjd00...fdhjsekdme
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Safety notices are included throughout to warn of potential injuries from parts propelled by springs or releasing pressurized fluids. Required tools are listed at the start, including link brackets, a transmission repair stand, bolts, pullers, and wrenches.
The document provides instructions for disassembling components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve. It lists required tools and safety precautions. The multi-step process includes draining fluids, removing covers, plates, seals, springs, and other parts. Detailed illustrations accompany each step to ensure correct disassembly and reassembly of components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, barrel assembly, piston assemblies, gears, seals, and other parts. Safety notices are included to warn of hazards like fluids, springs, and heavy components. Required tools are listed.
The document provides instructions for disassembling various components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve. It lists required tools and safety precautions. The multi-step process includes draining fluids, removing covers, plates, seals, springs, and other parts. Detailed illustrations accompany each step to ensure correct disassembly and proper reinstallation of components.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing springs or draining fluids. The goal is to disassemble the major components into their individual parts to prepare for cleaning, inspection or repair.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Safety notices are included throughout to warn of potential injuries from parts propelled by springs or releasing pressurized fluids. Required tools are listed in a table at the beginning.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing pressurized components or springs. The goal is to disassemble the major assemblies into their individual parts to prepare for cleaning, inspection or repair.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists 19 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized fluids. Dismantling requires specialty tools like pullers, wrenches, and pliers.
Caterpillar cat 313 f lgc excavator (prefix gjd) service repair manual (gjd00...fdhjsekdme
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Safety notices are included throughout to warn of potential injuries from parts propelled by springs or releasing pressurized fluids. Required tools are listed at the start, including link brackets, a transmission repair stand, bolts, pullers, and wrenches.
Caterpillar cat 313 f lgc excavator (prefix gjd) service repair manual (gjd00...jdfjskekmdme
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Safety notices are included throughout to warn of potential injuries from springs or pressurized components. Required tools include pullers, drivers, wrenches, and other equipment to properly remove parts in their listed order.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing springs or draining fluids. The goal is to disassemble the major components into their individual parts to prepare for cleaning, inspection or repair.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Safety notices are included throughout to warn of potential injuries from parts propelled by springs or releasing pressurized fluids. Required tools are listed at the start, including link brackets, a transmission repair stand, bolts, pullers, and wrenches.
Caterpillar cat 313 f lgc excavator (prefix gjd) service repair manual (gjd00...dikdkskdmmd
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists 19 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized fluids. Dismantling requires specialty tools like pullers, wrenches, and pliers.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Pictures and diagrams accompany each step to illustrate how to remove parts like sprockets, valves, pistons, gears, seals and other components. Safety notices are included throughout to warn of potential injury from parts or stored energy.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing springs or draining fluids. The goal is to disassemble the major components into their individual parts to prepare for cleaning, inspection or repair.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing springs or draining fluids. The goal is to disassemble the major components into their individual parts to prepare for cleaning, inspection or repair.
Caterpillar cat 313 f lgc excavator (prefix gjd) service repair manual (gjd00...fjkskefksmeme
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It outlines 16 steps to disassemble the final drive, removing components like the sprocket, traction control valve, and barrel assembly. It then details 14 steps to disassemble the counterbalance valve, removing parts like the spool, springs, and relief valves. Finally, it lists 11 steps to disassemble the travel motor, removing the piston assembly, guide assembly, separator and friction plates, and barrel assembly components. Safety notices are included throughout regarding fluid containment and release of stored energy from springs.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and more. Safety notices are included throughout to warn of potential injury from parts or fluids.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and other components while taking safety precautions for things like pressurized fluids and springs.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and more. Safety notices are included throughout to warn of potential injury from parts or fluids.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to show each step. Safety notices warn of potential injuries from springs or fluids and recommend proper protective equipment.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to identify each part and show their position. Safety notices are included to warn of potential injuries from springs or fluids.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to show each step. Safety notices warn of potential injuries from springs or fluids and recommend proper protective equipment.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...fdhjsekdme
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and more. Safety notices are included throughout to warn of potential injury from parts or fluids.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...dikdkskdmmd
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists 19 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and other parts. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid. Detailed illustrations supplement each disassembly step.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...jdfjskekmdme
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists 19 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and other parts. Safety precautions are provided to release pressures and contain fluids. Tools required are also listed.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and more. Safety notices are included throughout to warn of potential injury from parts or fluids.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists required tools and outlines 16 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and plates. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to show each step. Safety notices warn of potential injuries from springs or fluids and recommend proper protective equipment.
1. The document provides removal and installation instructions for a fuel injection pump on a 320DL excavator with a C6.4 engine.
2. The procedure describes disconnecting fuel lines and harness assemblies, removing mounting hardware, and using identification marks to ensure proper installation orientation.
3. Cleanliness is emphasized and special tools are required to disconnect the high pressure fuel lines before the pump can be removed from the engine.
Caterpillar Cat 320D2 L Excavator (Prefix DNP) Service Repair Manual (DNP0000...jse7039222
The document provides assembly and disassembly instructions for components of a 320D2 excavator, including:
- Assembling the swing drive by installing bearings, seals, gears, and housings in 22 steps.
- Removing the swing gear and bearing by lifting it from the undercarriage frame after removing bolts and seals in 6 steps.
- Providing tools, illustrations and safety notes for the procedures.
More Related Content
Similar to Caterpillar Cat 313F LGC Excavator (Prefix GJD) Service Repair Manual (GJD00001 and up).pdf
Caterpillar cat 313 f lgc excavator (prefix gjd) service repair manual (gjd00...jdfjskekmdme
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Safety notices are included throughout to warn of potential injuries from springs or pressurized components. Required tools include pullers, drivers, wrenches, and other equipment to properly remove parts in their listed order.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing springs or draining fluids. The goal is to disassemble the major components into their individual parts to prepare for cleaning, inspection or repair.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Safety notices are included throughout to warn of potential injuries from parts propelled by springs or releasing pressurized fluids. Required tools are listed at the start, including link brackets, a transmission repair stand, bolts, pullers, and wrenches.
Caterpillar cat 313 f lgc excavator (prefix gjd) service repair manual (gjd00...dikdkskdmmd
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists 19 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized fluids. Dismantling requires specialty tools like pullers, wrenches, and pliers.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Pictures and diagrams accompany each step to illustrate how to remove parts like sprockets, valves, pistons, gears, seals and other components. Safety notices are included throughout to warn of potential injury from parts or stored energy.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing springs or draining fluids. The goal is to disassemble the major components into their individual parts to prepare for cleaning, inspection or repair.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, planetary gear sets, and counterbalance valve assemblies. Proper tools are required and safety precautions must be followed when releasing springs or draining fluids. The goal is to disassemble the major components into their individual parts to prepare for cleaning, inspection or repair.
Caterpillar cat 313 f lgc excavator (prefix gjd) service repair manual (gjd00...fjkskefksmeme
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It outlines 16 steps to disassemble the final drive, removing components like the sprocket, traction control valve, and barrel assembly. It then details 14 steps to disassemble the counterbalance valve, removing parts like the spool, springs, and relief valves. Finally, it lists 11 steps to disassemble the travel motor, removing the piston assembly, guide assembly, separator and friction plates, and barrel assembly components. Safety notices are included throughout regarding fluid containment and release of stored energy from springs.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and more. Safety notices are included throughout to warn of potential injury from parts or fluids.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and other components while taking safety precautions for things like pressurized fluids and springs.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and more. Safety notices are included throughout to warn of potential injury from parts or fluids.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to show each step. Safety notices warn of potential injuries from springs or fluids and recommend proper protective equipment.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to identify each part and show their position. Safety notices are included to warn of potential injuries from springs or fluids.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to show each step. Safety notices warn of potential injuries from springs or fluids and recommend proper protective equipment.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...fdhjsekdme
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and more. Safety notices are included throughout to warn of potential injury from parts or fluids.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...dikdkskdmmd
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists 19 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and other parts. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid. Detailed illustrations supplement each disassembly step.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...jdfjskekmdme
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists 19 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and other parts. Safety precautions are provided to release pressures and contain fluids. Tools required are also listed.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to accompany each step for properly removing parts like sprockets, valves, gears, seals and more. Safety notices are included throughout to warn of potential injury from parts or fluids.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313F LGC excavator. It lists required tools and outlines 16 steps to disassemble the components, including draining fluids, removing covers, pistons, springs, and plates. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
The document provides disassembly instructions for the final drive and travel motor of a 313F LGC excavator. It describes removing over 50 individual parts in 3 main sections: disassembly of the final drive and travel motor, disassembly of the counterbalance valve, and disassembly of the travel motor. Detailed illustrations are provided to show each step. Safety notices warn of potential injuries from springs or fluids and recommend proper protective equipment.
Similar to Caterpillar Cat 313F LGC Excavator (Prefix GJD) Service Repair Manual (GJD00001 and up).pdf (20)
1. The document provides removal and installation instructions for a fuel injection pump on a 320DL excavator with a C6.4 engine.
2. The procedure describes disconnecting fuel lines and harness assemblies, removing mounting hardware, and using identification marks to ensure proper installation orientation.
3. Cleanliness is emphasized and special tools are required to disconnect the high pressure fuel lines before the pump can be removed from the engine.
Caterpillar Cat 320D2 L Excavator (Prefix DNP) Service Repair Manual (DNP0000...jse7039222
The document provides assembly and disassembly instructions for components of a 320D2 excavator, including:
- Assembling the swing drive by installing bearings, seals, gears, and housings in 22 steps.
- Removing the swing gear and bearing by lifting it from the undercarriage frame after removing bolts and seals in 6 steps.
- Providing tools, illustrations and safety notes for the procedures.
The document provides installation instructions for a swing gear and bearing on excavator models 320D2 and 320D2 L. It outlines 22 steps to assemble the swing drive, including installing bearings, seals, gears, housings and fasteners in the proper order. Tools and lubricants required for the installation are listed in a table. The process involves lifting and positioning heavy components weighing up to 280 kg.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling the rocker shaft into individual parts and reassembling it.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, rear crankshaft seal, and installing replacements. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
1) The document provides instructions for installing a flywheel on a Caterpillar 320 GC excavator. It describes cleaning and preparing the crankshaft, installing guide studs and lifting the flywheel into place, then bolting it securely and checking the run out.
2) Additional steps are outlined for removing and installing the crankshaft rear seal and flywheel housing. The crankshaft rear seal is press-fit as a one-piece assembly and must be replaced if removed. Dowels, gaskets and seals are also installed during flywheel housing replacement.
3) Precise torques are specified for bolts depending on their grade, and alignment of the flywheel housing to the
Caterpillar Cat 318D2 L Excavator (Prefix HAH) Service Repair Manual (HAH0000...jse7039222
This document provides instructions for disassembling the final drive of a 318D2 L excavator. It lists the required tools and presents a step-by-step process involving 31 steps. Some key steps include fastening the final drive to a repair stand, removing bolts and washers to access internal components, and using various tools to separate parts like the carrier assembly, ring gears, planetary gears, and seals from the main housing. Proper cleaning and safety precautions are noted throughout.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and gives step-by-step instructions to remove components like the final drive cover, planetary assembly, retaining rings, and seals. It then describes the assembly process in reverse, including cleaning parts, replacing seals and O-rings, and torquing fasteners to the specified values. The goal is to repair or replace worn parts while maintaining cleanliness for proper functioning of the final drive.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing. Reassembly requires precisely installing seals, bearings, shims and other parts in the reverse order and verifying proper bearing preload using a press and micrometers. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing pieces. Reassembly requires precisely installing new seals and bearings then measuring clearance to determine the correct shim thickness before reinstalling all components in reverse order. Cleanliness and applying lubricant to parts is emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...jse7039222
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing various components like the head, check valves, fittings, brake piston, piston guide, barrel assembly, and shaft assembly. It then lists 22 steps for assembly, covering installation of seals, plates, piston shoe assemblies, cam plate, springs, and other components in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, cam plate, shaft assembly and more. The assembly process has 24 steps and instructs technicians to thoroughly clean parts, apply lubricants, and reinstall components in their original positions and orientations. Technicians are warned to take care handling parts and aligning components properly to prevent damage.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. The disassembly process involves 28 steps to remove components like bolts, seals, springs, pistons, and bearings. The assembly process reverses the disassembly steps and includes precautions like cleaning parts, applying lubricant, and ensuring proper placement of springs, seals and other components. Tools required include link brackets, slide hammers, bearing pullers, drivers and turning tools.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...jse7039222
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by using tools to remove bearings. It then lists 27 steps for assembly in reverse order, including cleaning parts, applying grease, and ensuring proper installation of seals and springs. The instructions emphasize cleanliness and using identification marks to ensure correct reinstallation of components.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...jse7039222
This document provides instructions for disassembling and assembling components of the rocker shaft assembly for a Caterpillar 315C excavator engine. It describes how to disassemble the rocker shaft by removing retaining rings, washers, rocker arms, and springs. It then describes the assembly process and includes illustrations showing the components. Precautions are provided regarding spring force. The document also provides instructions for installing the rocker shaft and pushrods and adjusting valve lash clearance.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F LGC EXCAVATOR GJD
Configuration: 313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine
Disassembly and Assembly
312F and 313F Excavators Machine Systems
Media Number -UENR6138-02 Publication Date -01/03/2015 Date Updated -14/12/2017
i05831822
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
C 8T-6699 Bolts 2
D
1P-0074 Slide Hammer Puller Gp 1
4C-5666 Threaded Adapter 1
123-6702 Backlash Gauge Gp 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
Start By:
a. Remove the final drive and the travel motor.
NOTICE
1/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor. The weight of the sprocket is
approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
2/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 1 g00940682
4. Use Tooling (A) and a suitable lifting device to position the final drive and the travel motor
onto Tooling (B). The combined weight of the final drive and travel motor is approximately
170 kg (375 lb).
5. Drain the oil from the final drive into a suitable container for storage or for disposal. Refer
to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the final
drive.
6. Remove fittings (1). Remove fittings (2) from traction control valve (3).
7. Remove nine bolts (4) that secure traction control valve (3) to the final drive.
8. Use two persons to remove traction control valve (3) from the final drive. The weight of
travel brake valve (3) is approximately 27 kg (60 lb).
3/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 2 g00940716
9. Remove valve plate (5) and O-ring seal (6).
Illustration 3 g01405139
10. Use Tooling (D) to remove bearing (7).
Disassembly of the Counterbalance Valve
Illustration 4 g01405725
4/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 5 g01405227
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Position the counterbalance valve, as shown. Remove plug (8) and adapter (9).
2. Remove spring (10) and spool (11).
Illustration 6 g01405232
5/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. 3. Remove relief valve assemblies (12).
Illustration 7 g01405243
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove seat (13). Seat (13) is pressed onto valve (17). Use new parts if seat (13) or valve
(17) is damaged. Do not disassemble these components. Make sure that you reuse the other
component.
5. Remove backup ring (14) and O-ring seal (15).
6. Remove O-ring seal (22).
7. Remove nut (20).
8. Remove screw (27).
9. Remove stopper (26). Remove backup ring (19) and O-ring seal (18) from stopper (19).
10. Remove valve (21), piston (25), and spring (16) from the housing.
11. Remove backup ring (23) and O-ring seal (24) from piston (25).
6/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 8 g01405284
Illustration 9 g01405299
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove covers (28) and the O-ring seals.
13. Remove springs (29), guides (30), and spool assembly (31).
7/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 10 g01405345
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
14. Remove valve (32), spring (33), and ball (34) from one end of spool (35). Repeat for the
other end of spool (35).
Illustration 11 g01405633
8/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
15. Remove plug (36), spring (38), and piston (39) from both sides of the housing assembly.
16. Remove O-ring seal (37) from each plug (36).
Note: Remove the remaining allen head bolts from the housing assembly for cleaning
purposes, if necessary. Each allen head bolt has an O-ring seal. Check the O-ring seal for
wear or for damage. Replace the O-ring seal, if necessary.
Disassembly of the Travel Motor
Illustration 12 g01405794
1. Remove O-ring seal (40) and springs (41).
9/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 13 g01405828
2. Install Tooling (C) onto piston assembly (42). Use Tooling (C) and a suitable prybar to
remove piston assembly (42) from body (43).
Illustration 14 g01405855
3. Remove O-ring seals (45) and (46) from piston assembly (42). Remove backup rings (44)
and (47) from piston assembly (42).
10/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 15 g01405867
4. Use suitable drivers or a suitable lever to remove guide assembly (48).
Illustration 16 g01405885
5. Remove O-ring seal (49) and backup ring (50) from guide assembly (48).
11/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 17 g01406117
6. Remove four separator plates (51) and four friction plates (52). Note the alternating order of
separator plates (51) and friction plates (52) for assembly purposes.
Note: Do not allow the components of barrel assembly (53) to come apart while you
remove barrel assembly (53). The components of barrel assembly (53) must be reinstalled
into the original positions.
Note: Oil will drain from the final drive. Place a suitable container under the final drive for
storage or disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for
the fluid capacity of the final drive.
7. Position the final drive horizontally.
8. Remove barrel assembly (53).
12/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 18 g01406180
Note: Mark the component locations for assembly purposes before you disassemble barrel
assembly (53).
9. Remove piston assemblies (54) and retainer (55) from barrel assembly (53).
Illustration 19 g01406210
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Remove retainer (56), spacer (57), and springs (58) from barrel assembly (53).
13/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 20 g01406263
11. Put location marks on cam plate (59) for assembly purposes. Make sure that the thick end of
cam plate (59) is adjacent to the opening that is across body (43). Remove cam plate (59).
Illustration 21 g01406329
Illustration 22 g01406338
14/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove piston (60) and spring (62).
13. Remove key (61).
Disassembly of the Final Drive
Illustration 23 g01406376
1. Use a suitable lifting device to position the final drive on Tooling (B), as shown. The weight
of the final drive is approximately 200 kg (441 lb).
2. Remove plugs (63). Remove the O-ring seals from plugs (63). Check the O-ring seals for
wear or for damage. Replace the O-ring seals, if necessary.
3. Remove bolts (65). Remove cover (64).
15/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 24 g01406386
4. Raise the temperature of bolts (66) in order to loosen the thread sealant.
5. Remove bolts (66) and plate (67).
Illustration 25 g01406397
6. Remove sun gear (68).
16/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 26 g01406400
7. Attach Tooling (A) and a suitable lifting device to carrier assembly (69). Remove carrier
assembly (69), planetary gear assembly (70), and bearing assembly (71) as a unit.
Illustration 27 g01406789
8. Remove planetary gear (70) and bearing assembly (71) from carrier assembly (69). Remove
the remaining planetary gears (70) and bearings (71).
Illustration 28 g01406822
9. Remove sun gear (72).
17/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. 10. Raise the temperature of bolts (73) in order to loosen the thread sealant. Remove bolts (73).
Remove plate (74).
Illustration 29 g01406850
11. Remove retaining ring (75) from sun gear (72). Check retaining ring (75) for wear or for
damage. Replace retaining ring (75), if necessary.
Illustration 30 g01406853
12. Remove planetary gear (76).
18/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 31 g01406875
13. Remove bearing (77), race (78), and thrust washer (79).
14. Repeat Steps 12 and 13 in order to remove the remaining planetary gear assemblies.
Illustration 32 g01406882
15. Remove bolt (80) and plate (81).
19/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 33 g01406885
Illustration 34 g01406886
16. Use Tooling (H) to remove nut (82).
Illustration 35 g01406906
17. Install Tooling (A) and a suitable lifting device to housing (83). The weight of housing (83)
is approximately 35 kg (77 lb).
18. Remove housing (83) from body assembly (84).
20/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 36 g01406912
19. Remove Duo-Cone Seal Gp seal (85) from the body assembly. Remove the Duo-Cone Seal
Gp seal from the housing.
Illustration 37 g01407100
20. Remove both bearings (86) from housing (83).
21/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 38 g01407089
21. Remove both bearings (87) from housing (83).
Illustration 39 g01407115
22. Position body assembly (84) horizontally. Remove shaft assembly (88), the bearing, and the
retaining ring.
22/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 40 g01407144
23. Use Tooling (G) to remove retaining ring (89) from shaft assembly (88).
Illustration 41 g01407161
24. Use Tooling (E), Tooling (F), and a suitable press to remove bearing (90).
Illustration 42 g01407166
25. Remove lip seal (91) from the body assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 7 23:51:16 UTC+0800 2020
23/23
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(S...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F LGC EXCAVATOR GJD
Configuration: 313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine
Disassembly and Assembly
312F and 313F Excavators Machine Systems
Media Number -UENR6138-02 Publication Date -01/03/2015 Date Updated -14/12/2017
i07219742
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-5474 M16x2x24 mm Lifting Eye Assembly 2
B 1P-2420 Transmission Repair Stand 1
C 8H-0663 Bearing Puller Assembly 1
D 422-5473 M12x1.75x21 mm Lifting Eye Assembly 2
E 422-5472 M10x1.5x16 mm Lifting Eye Assembly 2
F 1U-9895 Crossblock 1
Start By:
a. Remove the final drive and the travel motor assembly.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/22
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor assembly. The weight of the
sprocket is approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
Illustration 1 g06256385
4. Use Tooling (A) and a suitable lifting device to position final drive assembly (1) onto
Tooling (B). The weight of final drive assembly (1) is approximately 163 kg (360 lb).
2/22
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. 5. Drain the oil from final drive assembly (1) into a suitable container for storage or for
disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity
of the final drive.
Illustration 2 g06256798
6. Remove plug (2), plugs (3), and the O-ring seals.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 3 g06256843
3/22
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine(SE...
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...