This document provides instructions for removing and installing the front gear group on a C4.4 engine. The key steps are:
1. Lock the crankshaft and camshaft in position using timing pins to maintain proper timing.
2. Mark the gears to indicate their original alignment before removal.
3. Remove the camshaft gear, idler gear, and any other components.
4. Clean and inspect the gears before installation. Install the gears in reverse order of removal, ensuring proper timing is maintained using the marks. Tighten all fasteners to the specified torques.
Caterpillar cat 313 f excavator (prefix prg) service repair manual (prg00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a C4.4 engine. The procedure involves using various tools to lock the crankshaft, camshaft and fuel injection pump in position before removing gears. Individual gears are removed and installed one at a time, ensuring proper timing is maintained through alignment of marks on each gear. End play and backlash are checked using gauges once installation is complete. Precautions are outlined to prevent damage to engine components.
Caterpillar cat 314 e lcr excavator (prefix dkd) service repair manual (dkd00...soeldksejdksem
This document provides instructions to remove and install the front gear group of a C4.4 engine. Key steps include:
1. Locking the crankshaft and camshaft positions using timing pins and tools before removing parts.
2. Marking gear alignments to ensure proper reinstallation.
3. Removing the camshaft gear, idler gear, and other front gears.
4. Cleaning and inspecting components before reinstalling gears in reverse order while maintaining proper timing.
Caterpillar cat 312 e excavator (prefix wey) service repair manual (wey00001 ...fjjskekdmmse
The document provides instructions for removing and installing the front gear group on 312E and 312E L excavator models powered by a C4.4 engine. The removal procedure involves using various tools to lock the crankshaft, camshaft and fuel injection pump in position before removing components like the idler gears, camshaft gear, and front housing bearing. The installation procedure outlines cleaning and inspecting components before reinstalling them in reverse order of removal, ensuring proper positioning and locking of gears.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
Caterpillar cat 329 el excavator (prefix tst) service repair manual (tst00001...ufjjjskkemmd
This document provides the removal and installation procedures for the front gear group on a 329E L EXCAVATOR model powered by a C7.1 engine. The removal procedure involves using turning tools to lock the crankshaft and camshaft positions, loosening rocker arm inserts to close the valves, and removing multiple gears and housings. The installation procedure specifies cleaning and inspecting components, installing required bearings and hubs in the correct positions, and ensuring proper locking of the crankshaft, camshaft, and fuel injection pump during the process.
The document provides instructions for removing and installing the idler gear on a C4.4 engine. There are separate procedures for a standard idler gear and a heavy-duty idler gear. The removal procedure involves locking the camshaft and crankshaft, removing mounting bolts, and tilting the gear out of position. The installation procedure involves cleaning and inspecting parts, aligning timing marks, lubricating components, and checking specifications such as end play and backlash. Tools and torque specifications are provided.
Caterpillar cat 320 e l excavator (prefix ree) service repair manual (ree0000...udfujjsejkkem
This document provides instructions for removing and installing the front gear group on a 320E L excavator with a C6.6 engine. The procedure includes using various tools to lock the crankshaft, camshaft, and fuel injection pump in position before removing gears. Alignment marks should be made on the gears. Cleaning and inspecting components is specified before installing the gears back in their original alignment. Various torque specifications are provided for tightening bolts.
Caterpillar cat 320 e excavator (prefix dfg) service repair manual (dfg00001 ...ufujjdjkskemme
The document provides instructions for removing and installing the front gear group on a Caterpillar 320E LN excavator engine. It lists the required tools and outlines 16 steps for removal, including locking the crankshaft, camshaft and fuel injection pump positions using timing pins. It then describes 11 steps for installation, including aligning timing marks on the gears, checking backlash and end play, and ensuring the valves are correctly positioned before operation. The purpose is to provide a procedure for removing and installing the front gear group while maintaining proper timing of engine components.
Caterpillar cat 313 f excavator (prefix prg) service repair manual (prg00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a C4.4 engine. The procedure involves using various tools to lock the crankshaft, camshaft and fuel injection pump in position before removing gears. Individual gears are removed and installed one at a time, ensuring proper timing is maintained through alignment of marks on each gear. End play and backlash are checked using gauges once installation is complete. Precautions are outlined to prevent damage to engine components.
Caterpillar cat 314 e lcr excavator (prefix dkd) service repair manual (dkd00...soeldksejdksem
This document provides instructions to remove and install the front gear group of a C4.4 engine. Key steps include:
1. Locking the crankshaft and camshaft positions using timing pins and tools before removing parts.
2. Marking gear alignments to ensure proper reinstallation.
3. Removing the camshaft gear, idler gear, and other front gears.
4. Cleaning and inspecting components before reinstalling gears in reverse order while maintaining proper timing.
Caterpillar cat 312 e excavator (prefix wey) service repair manual (wey00001 ...fjjskekdmmse
The document provides instructions for removing and installing the front gear group on 312E and 312E L excavator models powered by a C4.4 engine. The removal procedure involves using various tools to lock the crankshaft, camshaft and fuel injection pump in position before removing components like the idler gears, camshaft gear, and front housing bearing. The installation procedure outlines cleaning and inspecting components before reinstalling them in reverse order of removal, ensuring proper positioning and locking of gears.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
Caterpillar cat 329 el excavator (prefix tst) service repair manual (tst00001...ufjjjskkemmd
This document provides the removal and installation procedures for the front gear group on a 329E L EXCAVATOR model powered by a C7.1 engine. The removal procedure involves using turning tools to lock the crankshaft and camshaft positions, loosening rocker arm inserts to close the valves, and removing multiple gears and housings. The installation procedure specifies cleaning and inspecting components, installing required bearings and hubs in the correct positions, and ensuring proper locking of the crankshaft, camshaft, and fuel injection pump during the process.
The document provides instructions for removing and installing the idler gear on a C4.4 engine. There are separate procedures for a standard idler gear and a heavy-duty idler gear. The removal procedure involves locking the camshaft and crankshaft, removing mounting bolts, and tilting the gear out of position. The installation procedure involves cleaning and inspecting parts, aligning timing marks, lubricating components, and checking specifications such as end play and backlash. Tools and torque specifications are provided.
Caterpillar cat 320 e l excavator (prefix ree) service repair manual (ree0000...udfujjsejkkem
This document provides instructions for removing and installing the front gear group on a 320E L excavator with a C6.6 engine. The procedure includes using various tools to lock the crankshaft, camshaft, and fuel injection pump in position before removing gears. Alignment marks should be made on the gears. Cleaning and inspecting components is specified before installing the gears back in their original alignment. Various torque specifications are provided for tightening bolts.
Caterpillar cat 320 e excavator (prefix dfg) service repair manual (dfg00001 ...ufujjdjkskemme
The document provides instructions for removing and installing the front gear group on a Caterpillar 320E LN excavator engine. It lists the required tools and outlines 16 steps for removal, including locking the crankshaft, camshaft and fuel injection pump positions using timing pins. It then describes 11 steps for installation, including aligning timing marks on the gears, checking backlash and end play, and ensuring the valves are correctly positioned before operation. The purpose is to provide a procedure for removing and installing the front gear group while maintaining proper timing of engine components.
Caterpillar cat 313 f l excavator (prefix prg) service repair manual (prg0000...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a C4.4 engine. The procedure involves using various tools to lock the crankshaft, camshaft and fuel injection pump in position before removing gears. Timing marks must be aligned and gears lubricated upon installation. Torque specifications are provided for tightening bolts on installed gears.
Caterpillar cat 313 f l excavator (prefix prg) service repair manual (prg0000...idkkddmmd1
This document provides instructions for removing and installing the front gear group on a C4.4 engine. The key steps are:
1. Lock the crankshaft and camshaft positions using timing pins to maintain timing.
2. Mark the gears to indicate their original alignment before removal.
3. Remove the camshaft and idler gears.
4. Clean and inspect the gear group components. Install the gears in reverse order while maintaining proper timing marks, end play, backlash, and torque specifications.
Caterpillar cat 313 f excavator (prefix prg) service repair manual (prg00001 ...idkkddmmd1
This document provides instructions for removing and installing the front gear group on a C4.4 engine. The procedure involves:
1. Locking the crankshaft and fuel injection pump in position using timing pins to maintain proper timing.
2. Removing the camshaft gear, idler gear, and other front gear group components.
3. Cleaning and inspecting the gear group components.
4. Installing the gears in proper alignment using timing marks and checking gear backlash and end play.
5. Locking the crankshaft and fuel injection pump again before final installation and startup.
Caterpillar cat 314 e lcr excavator (prefix dkd) service repair manual (dkd00...fhsejkdkmem
This document provides instructions for removing and installing the front gear group on a C4.4 engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Marking the gears to ensure proper alignment during reinstallation.
3. Removing the idler gear and camshaft gear.
4. Cleaning and inspecting components before reinstalling in reverse order while checking gear mesh, backlash, and end play.
Caterpillar cat 314 e lcr excavator (prefix dkd) service repair manual (dkd00...fhsjekkdkem
This document provides instructions for removing and installing the front gear group on a C4.4 engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Marking the gears to ensure proper alignment during reinstallation.
3. Removing the idler gear and camshaft gear.
4. Cleaning and inspecting components before reinstalling in reverse order while checking gear mesh, backlash, and end play.
Caterpillar cat 314 e lcr excavator (prefix ecn) service repair manual (ecn00...fhsjejkdm
The document provides instructions for removing and installing the front gear group on a Caterpillar 314E excavator engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Removing the idler gear and camshaft gear after marking their positions for alignment during installation.
3. Cleaning and inspecting components before installation and using a dial indicator to check gear clearances and backlash.
4. Reinstalling the gears, checking timing marks are aligned, and tightening fasteners to the specified torques before reassembling covers.
Caterpillar cat 314 e cr excavator (prefix ecn) service repair manual (ecn000...jfdjskmdmme
1. The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine.
2. It describes locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
3. Key steps include removing the gears in reverse order of installation, cleaning and inspecting parts, aligning timing marks, checking clearances, and lubricating the installed gears.
Caterpillar cat 314 e cr excavator (prefix ecn) service repair manual (ecn000...fhsjejkdm
The document provides instructions for removing and installing the front gear group on a Caterpillar 314E excavator engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Removing the idler gear and camshaft gear after marking their positions for alignment during installation.
3. Cleaning and inspecting removed components prior to installation.
4. Installing the camshaft gear and idler gear, checking gear mesh and end play, and lubricating the gears.
Caterpillar cat 314 e sr excavator (prefix ecn) service repair manual (ecn000...jfdjskmdmme
1. The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine.
2. It describes locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
3. Key steps include removing the gears in reverse order of installation, cleaning and inspecting parts, aligning timing marks on the gears, checking gear clearances, and lubricating the installed gears.
Caterpillar cat 314 e lcr excavator (prefix ecn) service repair manual (ecn00...jfdjskmdmme
1. The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine.
2. It describes locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
3. Key steps include removing the gears in reverse order of installation, cleaning and inspecting parts, aligning timing marks, checking clearances, and lubricating gears before installation.
Caterpillar cat 314 e sr excavator (prefix ecn) service repair manual (ecn000...fhsjejkdm
1. The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine.
2. It describes locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing throughout the repair.
3. Key steps include removing and installing the camshaft and idler gears while aligning timing marks and checking gear backlash and end play with gauges.
Hyundai r22 7 mini excavator service repair manualfjjsekdmme
This service manual provides maintenance and repair instructions for the machine. It includes sections on safety precautions, an outline of the machine components, inspection and maintenance procedures, disassembly and assembly instructions, and troubleshooting. Proper maintenance is important to prevent failures and problems. The manual aims to help technicians efficiently service the machine by providing accurate descriptions and repair techniques. Routine maintenance includes checking fluid levels, lubricating components, inspecting parts for wear and damage, and replacing filters at regular intervals. Precautions should be taken during disassembly, assembly, and operation to ensure safety and efficiency.
Hyundai r16 7 mini excavator service repair manualfjjsekdmme
This service manual provides instructions for maintaining and repairing an excavator. It outlines the machine's components and systems, inspection and maintenance procedures, and repair techniques. The manual instructs technicians to thoroughly clean parts, use the proper tools and fasteners, and replace worn components to efficiently service the excavator. Regular maintenance such as checking fluid levels, lubricating parts, and inspecting for damage is recommended at intervals of 50, 100, 250, 500, and 1,000 hours of use. The manual aims to help technicians properly maintain the excavator to ensure long life.
Hyundai r15 7 mini excavator service repair manualfjjsekdmme
This service manual provides maintenance and repair instructions for the HY1570001 excavator. It outlines inspection and maintenance procedures, including checking fluid levels, lubricating parts, inspecting wear items, and adjusting components. The manual emphasizes performing repairs correctly using the proper tools, materials, and techniques. Maintaining the excavator according to the schedules in the manual will help ensure long life and prevent failures.
Hyundai l4 gc diesel engine service repair manualfjjsekdmme
This shop manual covers service procedures for the Hyundai L4GC industrial engine. It includes specifications, troubleshooting, removal, installation, disassembly and assembly procedures to facilitate efficient service and repair. Proper service methods and repair procedures are essential for the safe and reliable operation of the engine. Read this manual thoroughly before servicing to purchase the correct parts and safely service the engine.
Hyundai hsl850 7 a skid steer loader service repair manualfjjsekdmme
This document provides instructions for removing and installing a hydraulic pump, as well as summarizing the pump's structure and components. It describes disconnecting hoses from the pump and loosening bolts to remove it. For installation, it says to tighten the bolts and reconnect the hoses. It then provides an overview of the pump's internal parts and ports. Subsequent sections give directions for adjusting pressure valves and settings. The document concludes with notes for disassembling and reassembling the pump, including replacing seals and ensuring proper orientation of parts.
Hyundai hsl850 7 skid steer loader service repair manualfjjsekdmme
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing the motor by draining oil, loosening bolts, and removing hydraulic lines and covers.
2) Disassembling the motor by removing pins, plates, seals, and shafts.
3) Cleaning and inspecting individual parts before reassembly.
4) Reassembling the motor by reversing the disassembly steps, replacing seals, and torquing bolts.
Hyundai hsl650 7 a skid steer loader service repair manualfjjsekdmme
The document provides instructions for removing and installing a travel motor on an excavator. Key steps include:
1. Lowering the bucket, shutting off the engine, and removing protective covers to access the travel motor.
2. Removing hydraulic lines and mounting bolts to separate the travel motor from the excavator.
3. Disassembling the travel motor by removing seals, gears, plates, and shafts.
4. Reassembling the travel motor by reversing the disassembly steps and ensuring proper alignment of parts.
Hyundai hsl650 7 skid steer loader service repair manualfjjsekdmme
This document provides instructions for removing and installing a main pump, describes the structure and components of the main pump, and gives an overview of the pump's operation and control system. It also provides guidelines for starting up and maintaining the pump, including filling it with oil, bleeding air from the system, checking charge pressure, and regularly changing the fluid and filter.
Hyundai hlf1518(c) 5 forklift truck service repair manualfjjsekdmme
This document provides an overview and instructions for the disassembly and assembly of a steering unit. It includes:
1) A list of tools needed and torque specifications for reassembly.
2) Step-by-step instructions for disassembling the steering unit and removing components like the end cover, gearwheel set, cardan shaft, and pressure relief valve parts.
3) Guidance on marking parts like the spool and sleeve to ensure proper reassembly.
4) Detailed steps for reassembling parts in the correct order and orientation, including installing seals, springs, and bearing races.
Hyundai hl730 3 wheel loader service repair manualfjjsekdmme
The document provides instructions for disassembling and assembling a priority valve and steering unit. It includes diagrams showing the parts of each system and the order for disassembly and assembly. Key steps for disassembly of the priority valve include loosening plugs, removing seals and springs, and pressing out the spool. Key steps for assembly include lubricating parts, placing seals and springs, and tightening plugs to the specified torque. The steering unit disassembly and assembly follows a similar process of removing and replacing individual parts like seals, bearings, plates and bushings. Cleaning and inspection of parts is recommended between disassembly and assembly.
Hyundai hl720 3 wheel loader service repair manualfjjsekdmme
The document provides instructions for disassembling and assembling a steering unit. It includes:
1) A list of parts for the priority valve and steering unit with labeled diagrams.
2) Steps for disassembling the priority valve and steering unit, which includes removing screws, pins, seals, springs, and other small parts.
3) Instructions for cleaning, inspecting, lubricating, and assembling the priority valve and steering unit, replacing worn parts as needed. Tightening torques and hydraulic connections are also provided.
More Related Content
Similar to Caterpillar cat 313 f l excavator (prefix prg) service repair manual (prg00001 and up)
Caterpillar cat 313 f l excavator (prefix prg) service repair manual (prg0000...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a C4.4 engine. The procedure involves using various tools to lock the crankshaft, camshaft and fuel injection pump in position before removing gears. Timing marks must be aligned and gears lubricated upon installation. Torque specifications are provided for tightening bolts on installed gears.
Caterpillar cat 313 f l excavator (prefix prg) service repair manual (prg0000...idkkddmmd1
This document provides instructions for removing and installing the front gear group on a C4.4 engine. The key steps are:
1. Lock the crankshaft and camshaft positions using timing pins to maintain timing.
2. Mark the gears to indicate their original alignment before removal.
3. Remove the camshaft and idler gears.
4. Clean and inspect the gear group components. Install the gears in reverse order while maintaining proper timing marks, end play, backlash, and torque specifications.
Caterpillar cat 313 f excavator (prefix prg) service repair manual (prg00001 ...idkkddmmd1
This document provides instructions for removing and installing the front gear group on a C4.4 engine. The procedure involves:
1. Locking the crankshaft and fuel injection pump in position using timing pins to maintain proper timing.
2. Removing the camshaft gear, idler gear, and other front gear group components.
3. Cleaning and inspecting the gear group components.
4. Installing the gears in proper alignment using timing marks and checking gear backlash and end play.
5. Locking the crankshaft and fuel injection pump again before final installation and startup.
Caterpillar cat 314 e lcr excavator (prefix dkd) service repair manual (dkd00...fhsejkdkmem
This document provides instructions for removing and installing the front gear group on a C4.4 engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Marking the gears to ensure proper alignment during reinstallation.
3. Removing the idler gear and camshaft gear.
4. Cleaning and inspecting components before reinstalling in reverse order while checking gear mesh, backlash, and end play.
Caterpillar cat 314 e lcr excavator (prefix dkd) service repair manual (dkd00...fhsjekkdkem
This document provides instructions for removing and installing the front gear group on a C4.4 engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Marking the gears to ensure proper alignment during reinstallation.
3. Removing the idler gear and camshaft gear.
4. Cleaning and inspecting components before reinstalling in reverse order while checking gear mesh, backlash, and end play.
Caterpillar cat 314 e lcr excavator (prefix ecn) service repair manual (ecn00...fhsjejkdm
The document provides instructions for removing and installing the front gear group on a Caterpillar 314E excavator engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Removing the idler gear and camshaft gear after marking their positions for alignment during installation.
3. Cleaning and inspecting components before installation and using a dial indicator to check gear clearances and backlash.
4. Reinstalling the gears, checking timing marks are aligned, and tightening fasteners to the specified torques before reassembling covers.
Caterpillar cat 314 e cr excavator (prefix ecn) service repair manual (ecn000...jfdjskmdmme
1. The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine.
2. It describes locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
3. Key steps include removing the gears in reverse order of installation, cleaning and inspecting parts, aligning timing marks, checking clearances, and lubricating the installed gears.
Caterpillar cat 314 e cr excavator (prefix ecn) service repair manual (ecn000...fhsjejkdm
The document provides instructions for removing and installing the front gear group on a Caterpillar 314E excavator engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Removing the idler gear and camshaft gear after marking their positions for alignment during installation.
3. Cleaning and inspecting removed components prior to installation.
4. Installing the camshaft gear and idler gear, checking gear mesh and end play, and lubricating the gears.
Caterpillar cat 314 e sr excavator (prefix ecn) service repair manual (ecn000...jfdjskmdmme
1. The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine.
2. It describes locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
3. Key steps include removing the gears in reverse order of installation, cleaning and inspecting parts, aligning timing marks on the gears, checking gear clearances, and lubricating the installed gears.
Caterpillar cat 314 e lcr excavator (prefix ecn) service repair manual (ecn00...jfdjskmdmme
1. The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine.
2. It describes locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
3. Key steps include removing the gears in reverse order of installation, cleaning and inspecting parts, aligning timing marks, checking clearances, and lubricating gears before installation.
Caterpillar cat 314 e sr excavator (prefix ecn) service repair manual (ecn000...fhsjejkdm
1. The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine.
2. It describes locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing throughout the repair.
3. Key steps include removing and installing the camshaft and idler gears while aligning timing marks and checking gear backlash and end play with gauges.
Similar to Caterpillar cat 313 f l excavator (prefix prg) service repair manual (prg00001 and up) (11)
Hyundai r22 7 mini excavator service repair manualfjjsekdmme
This service manual provides maintenance and repair instructions for the machine. It includes sections on safety precautions, an outline of the machine components, inspection and maintenance procedures, disassembly and assembly instructions, and troubleshooting. Proper maintenance is important to prevent failures and problems. The manual aims to help technicians efficiently service the machine by providing accurate descriptions and repair techniques. Routine maintenance includes checking fluid levels, lubricating components, inspecting parts for wear and damage, and replacing filters at regular intervals. Precautions should be taken during disassembly, assembly, and operation to ensure safety and efficiency.
Hyundai r16 7 mini excavator service repair manualfjjsekdmme
This service manual provides instructions for maintaining and repairing an excavator. It outlines the machine's components and systems, inspection and maintenance procedures, and repair techniques. The manual instructs technicians to thoroughly clean parts, use the proper tools and fasteners, and replace worn components to efficiently service the excavator. Regular maintenance such as checking fluid levels, lubricating parts, and inspecting for damage is recommended at intervals of 50, 100, 250, 500, and 1,000 hours of use. The manual aims to help technicians properly maintain the excavator to ensure long life.
Hyundai r15 7 mini excavator service repair manualfjjsekdmme
This service manual provides maintenance and repair instructions for the HY1570001 excavator. It outlines inspection and maintenance procedures, including checking fluid levels, lubricating parts, inspecting wear items, and adjusting components. The manual emphasizes performing repairs correctly using the proper tools, materials, and techniques. Maintaining the excavator according to the schedules in the manual will help ensure long life and prevent failures.
Hyundai l4 gc diesel engine service repair manualfjjsekdmme
This shop manual covers service procedures for the Hyundai L4GC industrial engine. It includes specifications, troubleshooting, removal, installation, disassembly and assembly procedures to facilitate efficient service and repair. Proper service methods and repair procedures are essential for the safe and reliable operation of the engine. Read this manual thoroughly before servicing to purchase the correct parts and safely service the engine.
Hyundai hsl850 7 a skid steer loader service repair manualfjjsekdmme
This document provides instructions for removing and installing a hydraulic pump, as well as summarizing the pump's structure and components. It describes disconnecting hoses from the pump and loosening bolts to remove it. For installation, it says to tighten the bolts and reconnect the hoses. It then provides an overview of the pump's internal parts and ports. Subsequent sections give directions for adjusting pressure valves and settings. The document concludes with notes for disassembling and reassembling the pump, including replacing seals and ensuring proper orientation of parts.
Hyundai hsl850 7 skid steer loader service repair manualfjjsekdmme
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing the motor by draining oil, loosening bolts, and removing hydraulic lines and covers.
2) Disassembling the motor by removing pins, plates, seals, and shafts.
3) Cleaning and inspecting individual parts before reassembly.
4) Reassembling the motor by reversing the disassembly steps, replacing seals, and torquing bolts.
Hyundai hsl650 7 a skid steer loader service repair manualfjjsekdmme
The document provides instructions for removing and installing a travel motor on an excavator. Key steps include:
1. Lowering the bucket, shutting off the engine, and removing protective covers to access the travel motor.
2. Removing hydraulic lines and mounting bolts to separate the travel motor from the excavator.
3. Disassembling the travel motor by removing seals, gears, plates, and shafts.
4. Reassembling the travel motor by reversing the disassembly steps and ensuring proper alignment of parts.
Hyundai hsl650 7 skid steer loader service repair manualfjjsekdmme
This document provides instructions for removing and installing a main pump, describes the structure and components of the main pump, and gives an overview of the pump's operation and control system. It also provides guidelines for starting up and maintaining the pump, including filling it with oil, bleeding air from the system, checking charge pressure, and regularly changing the fluid and filter.
Hyundai hlf1518(c) 5 forklift truck service repair manualfjjsekdmme
This document provides an overview and instructions for the disassembly and assembly of a steering unit. It includes:
1) A list of tools needed and torque specifications for reassembly.
2) Step-by-step instructions for disassembling the steering unit and removing components like the end cover, gearwheel set, cardan shaft, and pressure relief valve parts.
3) Guidance on marking parts like the spool and sleeve to ensure proper reassembly.
4) Detailed steps for reassembling parts in the correct order and orientation, including installing seals, springs, and bearing races.
Hyundai hl730 3 wheel loader service repair manualfjjsekdmme
The document provides instructions for disassembling and assembling a priority valve and steering unit. It includes diagrams showing the parts of each system and the order for disassembly and assembly. Key steps for disassembly of the priority valve include loosening plugs, removing seals and springs, and pressing out the spool. Key steps for assembly include lubricating parts, placing seals and springs, and tightening plugs to the specified torque. The steering unit disassembly and assembly follows a similar process of removing and replacing individual parts like seals, bearings, plates and bushings. Cleaning and inspection of parts is recommended between disassembly and assembly.
Hyundai hl720 3 wheel loader service repair manualfjjsekdmme
The document provides instructions for disassembling and assembling a steering unit. It includes:
1) A list of parts for the priority valve and steering unit with labeled diagrams.
2) Steps for disassembling the priority valve and steering unit, which includes removing screws, pins, seals, springs, and other small parts.
3) Instructions for cleaning, inspecting, lubricating, and assembling the priority valve and steering unit, replacing worn parts as needed. Tightening torques and hydraulic connections are also provided.
Crown we2000 series forklift parts catalogue manualfjjsekdmme
This document is a parts manual for the WE/WS2000 series. It contains 10 sections that list parts for different systems of the trucks, including covers, frames, hydraulic and electrical components, brakes, and more. Each section includes an index listing part numbers, part names, and quantities of parts required. Product information like model numbers and serial numbers are needed to order replacement parts.
Crown wd2300 s series walkie reach stacker parts catalogue manualfjjsekdmme
This document is a parts manual for a WD2300S series truck. It contains sections that list and describe parts for different systems of the truck, including covers, caster wheels, hydraulic parts, drive systems, electrical systems, brakes, mast/lift structures, cylinders, and the cabin/platform. Diagrams show the layout of hydraulic tubes and hoses. Part numbers are provided to order replacement parts. The manual instructs readers to specify the truck model and serial number to ensure the correct parts are ordered.
Crown wav50 work assit vehicle parts catalogue manualfjjsekdmme
This parts manual provides concise part listings and diagrams for replacing parts on a WAV 50 Series order number 812718-006. It includes 3 sentences or less summaries of each section:
Section 1 covers front chassis parts including the battery, bumpers, and controller mounting plate. Section 2 covers the hydraulic unit. Section 3 covers drive unit parts such as the drive motor and brake assembly. Section 4 covers electrical parts including contactors and switches. Sections 7-10 cover mast, cylinder, platform and miscellaneous parts such as labels and decals.
Crown tsp6000 series turret order picker parts catalogue manualfjjsekdmme
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, listed with their part numbers and the quantity required. Key components included are the power unit enclosure, hinges, screws, nuts, doors, covers, rods, screens, washers, pins and rings.
Crown sx3000 series forklift parts catalogue manualfjjsekdmme
This document is a parts manual for the SX3000 series truck. It contains 10 sections that describe the various parts of the truck. Section 2 covers the hydraulic system, including tube and hose layout diagrams. The diagrams show the routing of hydraulic tubes and hoses between components like the power unit, lift cylinders, and reservoir. Parts are identified by number and include things like tubes, hoses, fittings and cylinders. Torque specifications and required quantities are also provided to aid in repairs or ordering replacements.
Crown st3000 series forklift parts catalogue manualfjjsekdmme
This parts manual provides information on replacement parts for the ST3000 series truck. It contains 10 sections covering various systems of the truck, including covers, outriggers, caster wheels, hydraulics, drive unit, electrical, brakes, mast/lift structure, cylinders, and miscellaneous parts. Each section lists the relevant part numbers, names, and quantities required. Important information is also provided on ordering spare parts and making any modifications to the truck.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F L EXCAVATOR PRG
Configuration: 313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820288
Gear Group (Front) - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107
Timing Pin
(Fuel Injection Pump)
1
D
136-4632
Timing Pin
(Crankshaft)
1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure.
NOTICE
1/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the front gear group. Carefully follow the procedure in order to remove the gear
group.
Illustration 1 g02485936
2/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. 1. Remove plug (1) from the cylinder block. Remove O-ring seal (2) from the plug.
2. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke.
3. Remove Tooling (D).
4. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
Illustration 2 g03707478
5. Use Tooling (E) in order to loosen threaded inserts (4) on all rocker arms (3). Unscrew
threaded inserts (4) on all rocker arms (3) until all valves are fully closed.
Note: Ensure that ALL threaded inserts are fully unscrewed.
6. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to Illustration 1.
3/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 3 g03707479
7. Install Tooling (B) through Hole (X) in camshaft gear (5) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position. Refer to System Operation,
Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct
procedure.
8. Install Tooling (D) into Hole (W) in the cylinder block. Use Tooling (D) in order to lock the
crankshaft in the correct position. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
9. Use Tooling (C) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
4/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 4 g03707480
Alignment of timing marks
10. Mark gear (5), gear (6), gear (7) and gear (8) in order to show alignment. Refer to
Illustration 4.
Note: Identification will ensure that the gears can be installed in the original alignment.
11. Remove camshaft gear (5). Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install" for the correct procedure.
12. Remove idler gear (6). Refer to Disassembly and Assembly, "Idler Gear - Remove and
Install" for the correct procedure.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin
(Camshaft)
1
5/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. C 364-9107
Timing Pin
(Fuel Injection Pump)
1
D
136-4632
Timing Pin
(Crankshaft)
1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
F
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the
fuel injection pump.
1. Ensure that number one piston is at top dead center on the compression stroke. Refer to
System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston"
for the correct procedure.
6/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 5 g02485938
2. If necessary, install Tooling (D) into Hole (W) in the cylinder block. Use Tooling (D) in
order to lock the crankshaft in the correct position. Refer to System Operation, Testing and
Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
3. Ensure that all of the components of the front gear group are clean and free from wear and
damage. If necessary, replace any components that are worn or damaged.
7/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 6 g03707481
8/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 7 g03707479
4. Install camshaft gear (5). Loosely install bolt (10) and washer (9) for the camshaft gear.
Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install" for more
information.
5. Install Tooling (B) through Hole (X) in camshaft gear (5) into the front housing.
9/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 8 g03707482
10/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 9 g03707480
Alignment of timing marks
6. Install idler gear (6). Ensure that the timing marks on gear (5), gear (6), gear (7) and gear (8)
are in alignment and that the mesh of the gears is correct. Refer to Disassembly and
Assembly, "Idler Gear - Remove and Install" for the correct procedure.
7. Use Tooling (F) in order to check the end play of the idler gear. Refer to Specifications,
"Gear Group (Front)" and refer to Disassembly and Assembly, "Idler Gear - Remove and
Install" for further information.
11/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 10 g03707483
8. Ensure that the fuel injection pump is locked in the correct position. Refer to Disassembly
and Assembly, "Fuel Injection Pump - Install" for the correct procedure.
9. Remove Tooling (B) and Tooling (C).
10. When bolt (10) is a 8.8 Grade. Tighten bolt (10) for camshaft gear (5) to a torque of 95 N·m
(70 lb ft).
When bolt (10) is a 10.9 Grade. Tighten bolt (10) for camshaft gear (5) to a torque of
120 N·m (89 lb ft).
11. Use Tooling (F) in order to check the end play of the camshaft gear. Refer to Specifications,
"Camshaft" for more information.
12/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 11 g03707484
12. Use Tooling (F) in order to measure the backlash for gear (5), gear (6), gear (7) and gear
(8). Refer to Specifications, "Gear Group (Front)" for further information.
13. Lubricate each gear with clean lubricating engine oil.
14. If necessary, use Tooling (A) in order to rotate the crankshaft so that number one piston is at
top dead center on the compression stroke. Refer to System Operation, Testing and
Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure. If
necessary, use Tooling (D) in order to lock the crankshaft so that number one piston is at top
dead center on the compression stroke.
15. Remove Tooling (D).
NOTICE
Failure to ensure that the crankshaft is positioned at the safe position
will result in interference between the pistons and the valves.
Interference between the pistons and the valves will result in damage to
the engine.
13/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 16. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
Illustration 12 g03707478
17. Use Tooling (E) in order to tighten threaded inserts (4) on all rocker arms (3). Tighten the
threaded inserts to a torque of 30 N·m (265 lb in).
Note: When the threaded insert is tightened, the threaded insert must be correctly seated
into the cup for the pushrod.
18. The engine should not be operated for a period 45 minutes after the threaded inserts on all
the rocker arms have been tightened. This period of time will allow the force from the valve
springs to purge off excessive engine oil from the hydraulic lifters.
14/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 13 g02485936
19. Install a new O-ring seal (1) to plug (2). Install the plug into Hole (W) in the cylinder block.
Tighten plug (2) to a torque of 21 N·m (186 lb in).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 9 00:41:30 UTC+0800 2020
15/15
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F L EXCAVATOR PRG
Configuration: 313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820289
Gear Group (Front) - Remove and Install - Heavy Duty Gear
Group (Front)
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107 Timing Pin (Fuel Injection Pump) 1
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure.
NOTICE
1/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the front gear group. Carefully follow the procedure in order to remove the gear
group.
1. If the air compressor is equipped with a hydraulic pump, remove the hydraulic pump. Refer
to Original Equipment Manufactures (OEM) for the correct procedure.
2. If the engine is equipped with an air compressor, remove the air compressor. Refer to
Disassembly and Assembly, "Air Compressor - Remove" for the correct procedure.
3. If the engine is equipped with only a hydraulic pump, remove the hydraulic pump. Refer to
OEM for the correct procedure.
4. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
2/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 1 g02486477
5. Remove plug (1) from the cylinder block. Remove O-ring seal (2) from the plug.
6. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke.
7. Remove Tooling (D).
8. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
3/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 2 g03706901
9. Use Tooling (E) in order to loosen threaded inserts (4) on all rocker arms (3). Unscrew
threaded inserts (4) on all rocker arms (3) until all valves are fully closed.
Note: Ensure that ALL threaded inserts are fully unscrewed.
10. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to Illustration 17.
4/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 3 g03706903
11. Install Tooling (B) through Hole (X) in camshaft gear (5) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position. Refer to System Operation,
Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct
procedure.
12. Use Tooling (C) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
5/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 4 g03706905
13. If the right-hand side of the engine is equipped with a hydraulic pump, remove the hydraulic
pump. Refer to OEM for the correct procedure.
14. If necessary, remove bolts (6) from plate (7). Remove plate (7) and remove O-ring seal (8).
15. Remove circlip (9) and remove gear assembly (10) from front housing (11).
6/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 5 g03706906
16. If necessary, follow Step 16.a through Step 16.b in order to disassemble gear assembly (10).
a. Remove circlip (12) from gear assembly (10).
b. Place gear assembly (10) on a suitable support. Press bearing (13) from gear (14).
7/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 6 g03706907
17. Mark gear (5), gear (15), gear (16) and gear (17) in order to show alignment. Refer to
Illustration 6.
Note: Identification will ensure that the gears can be installed in the original alignment.
18. Remove camshaft gear (6). Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install" for the correct procedure.
8/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 7 g03706909
19. Remove bolts (21) and bolts (23).
20. Remove tube assembly (22) from idler gear (15) and idler gear (25).
21. Remove plate (20).
22. Remove idler gear (15) from hub (19) (not shown).
23. Remove idler gear (25) and idler gear hub (24) from front housing (11).
24. Remove hub (19) (not shown) from front housing (11).
25. If necessary, remove bearing (18) from front housing (11). Refer to Disassembly and
Assembly, "Housing (Front) - Remove" for the correct procedure.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
9/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. B 230-6284 Timing Pin (Camshaft) 1
C 364-9107 Timing Pin (Fuel Injection Pump) 1
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
F 207-1601 Rubber Lubricant 1
G 7M-7456 Bearing Mount Compound 1
H
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the
fuel injection pump.
1. Ensure that number one piston is at top dead center on the compression stroke. Refer to
System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston"
for the correct procedure.
10/21
313F & 313F L Excavators PRG00001-UP (MACHINE) POWERED BY C4.4 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...