This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists required tools and outlines 33 steps to completely disassemble the final drive and its components. This includes removing springs, seals, gears, shafts, housings and other parts using various tools while taking safety precautions for parts under pressure. The goal is to disassemble the entire final drive assembly for repair or replacement of parts.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It describes 33 steps to remove components such as plugs, springs, seats, spools, adapters, valves and seals. Special care must be taken when removing pressurized components to avoid injury from parts propelled by released spring forces. Cleanliness is important to prevent contamination during disassembly.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 318 d2 l excavator (prefix hah) service repair manual (hah000...fjskefkemms
This document provides instructions for disassembling the final drive of a 318D2 L excavator. It describes removing 33 parts in 27 steps, including the sprocket, plugs, springs, seats, valves, adapters, and seals. Special care must be taken when removing parts under spring pressure. Various tools are required, and the document provides part numbers. Cleanliness is important to prevent dirt entry during disassembly.
Caterpillar cat 323 d2 l excavator (prefix kce) service repair manual (kce000...fusjejkdkmse
This document provides disassembly and assembly instructions for the final drive of a 323D2 L excavator. It describes how to disassemble the final drive components including removing the cover, carrier assembly, ring gears, and other parts. It then describes how to assemble the final drive by installing bearings, shims, seals, and other components in reverse order of disassembly. The document contains detailed steps and illustrations to guide the process.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 326 d2 l excavator (prefix rec) service repair manual (rec000...fikkskmmdm
This document provides instructions to disassemble a final drive on an excavator. It outlines 33 steps to fully disassemble the final drive. Key steps include removing the cover, carrier assembly, planetary gears, and separating the main housing from the motor housing. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It describes 33 steps to remove components such as plugs, springs, seats, spools, adapters, valves and seals. Special care must be taken when removing pressurized components to avoid injury from parts propelled by released spring forces. Cleanliness is important to prevent contamination during disassembly.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 318 d2 l excavator (prefix hah) service repair manual (hah000...fjskefkemms
This document provides instructions for disassembling the final drive of a 318D2 L excavator. It describes removing 33 parts in 27 steps, including the sprocket, plugs, springs, seats, valves, adapters, and seals. Special care must be taken when removing parts under spring pressure. Various tools are required, and the document provides part numbers. Cleanliness is important to prevent dirt entry during disassembly.
Caterpillar cat 323 d2 l excavator (prefix kce) service repair manual (kce000...fusjejkdkmse
This document provides disassembly and assembly instructions for the final drive of a 323D2 L excavator. It describes how to disassemble the final drive components including removing the cover, carrier assembly, ring gears, and other parts. It then describes how to assemble the final drive by installing bearings, shims, seals, and other components in reverse order of disassembly. The document contains detailed steps and illustrations to guide the process.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 326 d2 l excavator (prefix rec) service repair manual (rec000...fikkskmmdm
This document provides instructions to disassemble a final drive on an excavator. It outlines 33 steps to fully disassemble the final drive. Key steps include removing the cover, carrier assembly, planetary gears, and separating the main housing from the motor housing. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components. Cleanliness is important to prevent dirt from entering during reassembly.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
The document provides assembly instructions for the main hydraulic pump in 3 steps:
1. Install various components such as bearings, seals, pistons, and plates onto the port block and pump housing.
2. Attach the assembled port block and pump to the pump housing and install additional components.
3. Install the completed main hydraulic pump onto the excavator and connect hoses and electrical harnesses. Tighten all bolts to the specified torques and fill the hydraulic system with oil.
Caterpillar cat 330 d excavator (prefix ern) service repair manual (ern00001 ...hhjsekmdmm
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 31 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg total weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, planetary gear assemblies, ring gear, carrier assemblies, and individual planet gears. Tools required include link brackets and forcing bolts to remove components. Safety notes are provided to clean parts before disassembly and have two people assist with heavier components.
Caterpillar cat 325 d l excavator (prefix pal) service repair manual (pal0000...fjsekdmmeed
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The disassembly procedure has 32 steps that remove components like gears, shafts, seals, and housings. The assembly procedure has 9 steps and instructs technicians to clean parts, apply lubricants, and press components back into place like bearings and seals. Proper cleaning and use of replacement parts is emphasized for correct reassembly.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 d excavator (prefix thj) service repair manual (thj00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper tools are required and safety notes are provided regarding cleanliness and part weights which can be substantial.
This document provides instructions for installing a cylinder head on a Caterpillar 350-A L excavator engine. The procedure involves:
1. Cleaning and preparing the cylinder head and block mating surfaces.
2. Installing a new cylinder head gasket and positioning the cylinder head on the block.
3. Applying oil to the cylinder head bolts and tightening them in the specified sequence.
4. Installing other components like pushrods, rocker arms, intake and exhaust components.
The instructions provide detailed steps and illustrations to correctly position and secure the cylinder head. Special attention is given to cleaning parts and applying the proper torque to the head bolts.
Caterpillar cat m325 d l mh excavator (prefix kgg) service repair manual (kgg...ifkkdmdmdm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M325D L MH EXCAVATOR. It involves removing over 30 individual parts in the correct order, including gears, shafts, bearings, seals and housings. Parts are to be cleaned thoroughly before assembly and lubricated appropriately. Assembly involves installing the parts in reverse order using the specified tools. Special care must be taken when handling heavy components to avoid injury.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists the required tools and presents a step-by-step process involving removing bolts, seals, gears, and other components. Safety notices are included to handle fluids properly and avoid injury from hydraulic pressure. The disassembly procedure removes the outer casing pieces and individually dismantles the internal gear and shaft assemblies.
The document is a service repair manual that provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists 33 steps to completely disassemble the final drive and related components. The steps include removing mounting bolts, seals, springs, gears, shafts, washers, and housings using various specialized tools. Safety warnings are provided regarding potential hazards such as heavy component weights, pressurized fluids, and released spring forces during the disassembly process.
The document is a service repair manual that provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists 33 steps to completely disassemble the final drive and related components. The steps include removing mounting bolts, seals, springs, gears, shafts, washers, and housings. Safety notices are provided throughout to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and released spring forces. Tools required for the disassembly are also listed.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...gongfuao7509
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...ze6074xunong
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for maintenance or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...f8seodkdmdmed3
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids or heavy components during the disassembly process.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...f8usejkdmmd8i
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for maintenance or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...tengtui535
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as heavy component weights, pressurized fluids, and released spring forces during the disassembly process. Tools required are listed in a table.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...yu5676962
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, shafts, and housings. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Tools required include lifting devices, stands, pins, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...f8usiejdkmdd
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
The document provides assembly instructions for the main hydraulic pump in 3 steps:
1. Install various components such as bearings, seals, pistons, and plates onto the port block and pump housing.
2. Attach the assembled port block and pump to the pump housing and install additional components.
3. Install the completed main hydraulic pump onto the excavator and connect hoses and electrical harnesses. Tighten all bolts to the specified torques and fill the hydraulic system with oil.
Caterpillar cat 330 d excavator (prefix ern) service repair manual (ern00001 ...hhjsekmdmm
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 31 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg total weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, planetary gear assemblies, ring gear, carrier assemblies, and individual planet gears. Tools required include link brackets and forcing bolts to remove components. Safety notes are provided to clean parts before disassembly and have two people assist with heavier components.
Caterpillar cat 325 d l excavator (prefix pal) service repair manual (pal0000...fjsekdmmeed
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The disassembly procedure has 32 steps that remove components like gears, shafts, seals, and housings. The assembly procedure has 9 steps and instructs technicians to clean parts, apply lubricants, and press components back into place like bearings and seals. Proper cleaning and use of replacement parts is emphasized for correct reassembly.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 d excavator (prefix thj) service repair manual (thj00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper tools are required and safety notes are provided regarding cleanliness and part weights which can be substantial.
This document provides instructions for installing a cylinder head on a Caterpillar 350-A L excavator engine. The procedure involves:
1. Cleaning and preparing the cylinder head and block mating surfaces.
2. Installing a new cylinder head gasket and positioning the cylinder head on the block.
3. Applying oil to the cylinder head bolts and tightening them in the specified sequence.
4. Installing other components like pushrods, rocker arms, intake and exhaust components.
The instructions provide detailed steps and illustrations to correctly position and secure the cylinder head. Special attention is given to cleaning parts and applying the proper torque to the head bolts.
Caterpillar cat m325 d l mh excavator (prefix kgg) service repair manual (kgg...ifkkdmdmdm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M325D L MH EXCAVATOR. It involves removing over 30 individual parts in the correct order, including gears, shafts, bearings, seals and housings. Parts are to be cleaned thoroughly before assembly and lubricated appropriately. Assembly involves installing the parts in reverse order using the specified tools. Special care must be taken when handling heavy components to avoid injury.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists the required tools and presents a step-by-step process involving removing bolts, seals, gears, and other components. Safety notices are included to handle fluids properly and avoid injury from hydraulic pressure. The disassembly procedure removes the outer casing pieces and individually dismantles the internal gear and shaft assemblies.
The document is a service repair manual that provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists 33 steps to completely disassemble the final drive and related components. The steps include removing mounting bolts, seals, springs, gears, shafts, washers, and housings using various specialized tools. Safety warnings are provided regarding potential hazards such as heavy component weights, pressurized fluids, and released spring forces during the disassembly process.
The document is a service repair manual that provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists 33 steps to completely disassemble the final drive and related components. The steps include removing mounting bolts, seals, springs, gears, shafts, washers, and housings. Safety notices are provided throughout to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and released spring forces. Tools required for the disassembly are also listed.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...gongfuao7509
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...ze6074xunong
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for maintenance or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...f8seodkdmdmed3
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids or heavy components during the disassembly process.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...f8usejkdmmd8i
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for maintenance or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...tengtui535
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as heavy component weights, pressurized fluids, and released spring forces during the disassembly process. Tools required are listed in a table.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...yu5676962
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, shafts, and housings. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Tools required include lifting devices, stands, pins, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...f8usiejdkmdd
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...f9oseikkdks
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...jfkskmmdmdm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, shafts, and housings. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Tools required include lifting devices, stands, pins, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...jfkskmdmmdd
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...gongfuao7509
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove parts such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as released spring forces or hot/pressurized hydraulic oil. The goal is to fully disassemble the final drive to allow inspection and replacement of components.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...yu5676962
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive components. Key steps include removing the final drive from the machine, disassembling internal components like carriers and planetary gears, and separating housings. Safety notices are included to warn of hazards like stored spring energy or hot/pressurized fluids.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...f8usejkdmmd8i
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It describes:
- Required tools for disassembly
- Removing the final drive assembly and positioning it on a repair stand
- Disassembling the final drive components like the cover, carrier assembly, ring gears, and housing
- Removing planetary gears, shafts, seals and other internal parts
The detailed step-by-step process involves removing over 30 individual parts and components from the final drive assembly. Cleanliness and proper lifting of heavy components are emphasized for safety.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...f8seodkdmdmed3
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive components. Key steps include removing the final drive from the machine, disassembling internal components like carriers and planetary gears, and separating housings. Safety notices are included to release pressures and handle heavy parts. The detailed process is intended to allow thorough disassembly for repair or replacement of parts.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...ze6074xunong
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive and its components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly while taking safety precautions for released spring forces, and using lifting devices to remove heavier internal components like the carrier assembly. The goal is to fully separate all individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...tengtui535
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove components such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and spring forces during disassembly.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual (DPJ0000...f8usiejdkmdd
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove parts such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and spring forces. Detailed illustrations accompany each step for clarity.
Similar to Caterpillar cat 313 d2 lgp excavator (prefix rkn) service repair manual (rkn00001 and up) (20)
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...jdfjskekmdme
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The camshaft is then removed by loosening bolts while aligning timing marks and lifting it out. Reinstallation requires aligning timing marks, lubricating the camshaft, and tightening bolts to specified torque to complete the job. Proper cleaning and lubrication are emphasized to prevent premature wear.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
Caterpillar cat 330 c excavator (prefix mkm) service repair manual (mkm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly procedure has 28 steps that remove components like the head, springs, plates, and seals. The assembly procedure reverses these steps and provides notes on cleaning, marking parts, and applying thread lock compounds. It cautions that cleanliness is important and springs can cause injury if not assembled properly.
Caterpillar cat 330 c excavator (prefix mca) service repair manual (mca00001 ...jdfjskekmdme
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c excavator (prefix kdd) service repair manual (kdd00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix jnk) service repair manual (jnk00001 ...jdfjskekmdme
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c excavator (prefix jcd) service repair manual (jcd00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The disassembly process involves removing 28 components from the travel motor in 28 steps, including removing the head, brake piston, rotating assembly, seals, and other internal parts.
2. Cleanliness is important during disassembly and assembly to prevent contamination. All parts should be cleaned and lubricated before assembly.
3. The assembly process reverses the disassembly steps, involving installing 28 components in 28 steps to reassemble the travel motor. Special tools and torque specifications are provided.
Caterpillar cat 330 c excavator (prefix jab) service repair manual (jab00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix haa) service repair manual (haa00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing seals and installing components in the reverse order of disassembly.
- Tools required include an adapter, nuts, washers, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound.
Caterpillar cat 330 c excavator (prefix gkx) service repair manual (gkx00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) Similarly, it outlines 28 steps for assembly, instructing technicians to replace all seals and gaskets and apply lubricant before reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout the process.
Caterpillar cat 330 c excavator (prefix gag) service repair manual (gag00001 ...jdfjskekmdme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor. It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
2) The assembly section lists 29 steps to reassemble the travel motor by replacing components in the reverse order of disassembly. Special tools are required for tasks like removing races and installing seals and rings.
3) Cleanliness is important during disassembly and assembly. Marks should be made to ensure parts are replaced in the same positions. Seal surfaces require compound and components need light oil applied before assembly.
Caterpillar cat 330 c excavator (prefix btm) service repair manual (btm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It details 28 steps for disassembly, removing components like the head, port plate, springs, brake piston, plates, and bearings. It then details 21 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Tools required are also listed.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator including:
1. The cylinder head removal procedure involves removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts in a specific tightening sequence.
3. Removing the spacer plate requires taking out seals and removing the plate from the cylinder head. Installing requires new seals and gaskets and ensuring surfaces are clean.
Caterpillar cat 330 b l excavator (prefix 8sr) service repair manual (8sr0000...jdfjskekmdme
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat 330 b l excavator (prefix 5ls) service repair manual (5ls0000...jdfjskekmdme
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 330B excavator engine. The procedures include using tools to check bearing clearances, installing bearings dry and oiled, tightening bolts in sequences, and verifying end play. The crankshaft removal requires aligning timing marks, removing caps and nuts, pushing pistons down, lifting the crankshaft out using brackets, and removing gears and seals.
Caterpillar cat 330 b l excavator (prefix 4rs) service repair manual (4rs0000...jdfjskekmdme
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe procedures for removing and installing the cylinder head, rocker shaft and pushrods. Specifically, they outline removing the cylinder head by first removing associated components like the fuel lines, exhaust manifold, and rocker shaft. They then describe loosening bolts and using lifting devices to remove the heavy cylinder head. Procedures are also provided for disassembling, cleaning, inspecting, and reassembling the rocker shaft.
Caterpillar cat 330 b excavator (prefix 9hn) service repair manual (9hn00001 ...jdfjskekmdme
This document provides instructions for removing and installing final drives on an excavator. Key steps include:
1. Releasing hydraulic pressure and removing the track assemblies.
2. Removing bolts and disconnecting hydraulic lines to separate the final drive from the undercarriage frame.
3. Cleaning components and installing new seals before reassembling in reverse order, taking care to properly tighten bolts and reconnect hydraulic components.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying clean oil to bolts before tightening to specified torques.
Caterpillar cat 330 b excavator (prefix 8sr) service repair manual (8sr00001 ...jdfjskekmdme
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat 330 b excavator (prefix 5ls) service repair manual (5ls00001 ...jdfjskekmdme
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 330B excavator engine. The procedures include using tools to check bearing clearances, installing bearings dry and oiled, torquing fasteners, and aligning identification marks. The crankshaft removal requires lifting it straight up after removing connecting rods, main bearing caps, and thrust plates.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 LGP EXCAVATOR RKN
Configuration: 313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR3323-06 Publication Date -01/06/2018 Date Updated -27/06/2018
i05453130
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
C 154-6181 Forcing Bolt 1
D 439-3940 Link Bracket 2
E
5F-7366 Forcing Bolt 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F - Loctite 5127 1
Start By:
a. Remove the final drive.
1/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly
clean the exterior of the component. This action will prevent dirt from entering the internal
mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from cover (2), and fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
3/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
4/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
5/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate two ring gears (17).
Note: Two ring gears (17) are held together with Tooling (F). It may be necessary to heat
ring gears (17) in order to soften the sealant. Do not heat over 135 °C (275 °F) for more
than thirty minutes.
6/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
7/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
8/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from main housing (18) once gear (26) is removed.
Make sure that the motor housing is supported.
Illustration 20 g00708211
25. Remove shims (27) from the main housing.
9/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from motor housing (28). The combined weight of main housing (18) and the final
drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
10/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 12 15:59:24 UTC+0800 2020
11/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 LGP EXCAVATOR RKN
Configuration: 313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR3323-06 Publication Date -01/06/2018 Date Updated -27/06/2018
i07255515
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 477-3191 M14x2x18 mm Lifting Eye Assembly 2
B 1P-2420 Transmission Repair Stand 1
C
6V-8214 M6x20mm Bolt 2
9X-8267 M6 Washer 2
D 8H-0663 Bearing Puller Assembly 1
E 422-5474 M16x2x24mm Lifting Eye Assembly 2
F 439-3938 Link Bracket 3
G 1U-9889 Crossblock 1
Start By:
a. Remove the final drive and the travel motor assembly.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor assembly. The weight of the
sprocket is approximately 36 kg (79 lb).
Illustration 1 g06260984
3. Use Tooling (A) and a suitable lifting device to position final drive assembly (1) onto
Tooling (B). The weight of final drive assembly (1) is approximately 281 kg (620 lb).
2/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06261012
Illustration 3 g06261017
4. Remove plug (2), spring (4), seat (3), and the O-ring seal.
Personal injury can result from being struck by parts propelled by a
released spring force.
3/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 4 g06261029
Illustration 5 g06261032
5. Remove plug (5), spring (6), seat (7), stem assembly (8), and the O-ring seal.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 6 g06261260
Illustration 7 g06261275
6. Remove plug (9), spring (12), seat (11), spool (10), and the O-ring seal.
Illustration 8 g06261285
7. Remove adapter (13) and the O-ring seal.
5/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 9 g06261336
Illustration 10 g06261344
8. Remove plug (14), spring (16), valve (15), and the O-ring seal.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
6/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 11 g06261519
Illustration 12 g06261532
9. Remove plug (17), spring (19), valve (18), and the O-ring seal.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 13 g06261538
Illustration 14 g06261539
10. Remove plugs (20) and the O-ring seals.
11. Remove plugs (21), springs (23), valves (22), and the O-ring seals.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 15 g06261563
12. Remove bolts (24) and valve body (25).
Illustration 16 g06263306
Port plate (28) may still be adhered to the barrel assembly.
13. Remove springs (26), port plate (28), and O-ring seals (27).
Illustration 17 g06261586
14. Remove bearing (29).
15. Remove O-ring seal (30).
9/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 18 g06261622
16. Use Tooling (C) and suitable prying devices to remove piston assembly (31).
Illustration 19 g06261625
17. Remove O-ring seal (32) and O-ring seal (33).
Illustration 20 g06261647
10/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 21 g06261665
18. Remove separator plates (34) and friction plates (35). Note the alternating order of separator
plates (34) and friction plates (35) for assembly purposes.
Illustration 22 g06261896
19. Remove barrel assembly (36). Do not allow the components of barrel assembly (36) to
come apart while you remove barrel assembly (36). The components of barrel assembly (36)
must be reinstalled in the original positions.
Illustration 23 g06261908
20. Remove piston assemblies (37) and retainer (38).
11/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 24 g06261915
21. Remove guide (39).
Illustration 25 g06261922
22. Remove springs (40).
12/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 26 g06261927
23. Put location marks on swashplate (41) for assembly purposes. Remove swashplate (41).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 27 g06261980
13/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 28 g06261983
24. Remove shaft assembly (42), keys (44), piston (43), and spring (45).
Illustration 29 g06261987
25. Use a suitable press and Tooling (D) to remove bearing (46) off the shaft assembly.
Illustration 30 g06262009
14/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...