The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, seals, and bearings. It then details 19 additional steps to disassemble the travel motor and counterbalance valve, removing pistons, plates, springs, and seals. Personal injury warnings are included to release pressures and spring forces safely when disassembling components.
This document provides instructions for disassembling various components of a 313D2 excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and fasteners, using pullers to remove bearings, and noting part locations and orientations for reassembly. Safety notices are included to warn of potential injuries from pressurized fluids, heavy lifting, and released spring forces.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of 313D2 and 313D2 GC excavator models. It lists the required tools and gives step-by-step instructions to remove components like sprockets, fittings, valves, seals, springs, pistons, plates, and barrels. Safety notices are included to warn of hazards like stored energy in springs, hot or pressurized fluids, and heavy component weights.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...fjkskefksmeme
1) The document provides disassembly instructions for components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification numbers where applicable.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, seals and other parts while taking care to mark locations for reassembly.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like parts propelled by springs, hydraulic pressure, and heavy component weights. Required tools are listed in a table at the beginning.
Caterpillar cat 312 d excavator (prefix dlp) service repair manual (dlp00001 ...fksjksmmde
This document provides instructions for disassembling various components of a 312D excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists the required tools and outlines 16 detailed steps to disassemble parts like the traction control valve, barrel assembly, piston assemblies, springs and seals. Safety notices are included to warn of potential injuries from parts or fluids.
Caterpillar cat 314 e cr excavator (prefix gmd) service repair manual (gmd000...jfdskekdmme
This document provides instructions for disassembling various components of a 314E CR excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists the required tools and outlines a step-by-step process for safely removing each part, noting precautions for releasing pressures and contained fluids. Detailed illustrations accompany each step to ensure correct reassembly.
Caterpillar cat 312 d excavator (prefix jbc) service repair manual (jbc00001 ...fksjksmmde
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 312D or 312D L excavator. It lists the required tools and gives step-by-step procedures for removing components such as sprockets, valves, gears, plates, seals, and other parts. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized fluids. Detailed illustrations supplement the text to show how to take each component apart.
This document provides instructions for disassembling various components of a 313D2 excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and fasteners, using pullers to remove bearings, and noting part locations and orientations for reassembly. Safety notices are included to warn of potential injuries from pressurized fluids, heavy lifting, and released spring forces.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of 313D2 and 313D2 GC excavator models. It lists the required tools and gives step-by-step instructions to remove components like sprockets, fittings, valves, seals, springs, pistons, plates, and barrels. Safety notices are included to warn of hazards like stored energy in springs, hot or pressurized fluids, and heavy component weights.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...fjkskefksmeme
1) The document provides disassembly instructions for components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification numbers where applicable.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, seals and other parts while taking care to mark locations for reassembly.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like parts propelled by springs, hydraulic pressure, and heavy component weights. Required tools are listed in a table at the beginning.
Caterpillar cat 312 d excavator (prefix dlp) service repair manual (dlp00001 ...fksjksmmde
This document provides instructions for disassembling various components of a 312D excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists the required tools and outlines 16 detailed steps to disassemble parts like the traction control valve, barrel assembly, piston assemblies, springs and seals. Safety notices are included to warn of potential injuries from parts or fluids.
Caterpillar cat 314 e cr excavator (prefix gmd) service repair manual (gmd000...jfdskekdmme
This document provides instructions for disassembling various components of a 314E CR excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists the required tools and outlines a step-by-step process for safely removing each part, noting precautions for releasing pressures and contained fluids. Detailed illustrations accompany each step to ensure correct reassembly.
Caterpillar cat 312 d excavator (prefix jbc) service repair manual (jbc00001 ...fksjksmmde
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 312D or 312D L excavator. It lists the required tools and gives step-by-step procedures for removing components such as sprockets, valves, gears, plates, seals, and other parts. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized fluids. Detailed illustrations supplement the text to show how to take each component apart.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hot/pressurized fluids. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and traction control valve. Safety notices are included throughout to warn of hazards like parts propelled by springs, hydraulic pressure, and heavy component weights. Dismantling involves draining fluids, removing seals and plates, and using various tools to separate interconnected mechanical parts.
The document provides disassembly instructions for the final drive, travel motor, and various components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hot/pressurized fluids. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists over 30 detailed steps to disassemble parts like the final drive, travel motor, counterbalance valve, and other systems. Tools and safety precautions are also provided to properly disassemble components and release spring forces. The purpose is to thoroughly clean and inspect parts prior to reassembly of the excavator systems.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety precautions are included to warn of hazards such as hydraulic pressure, heavy component weights, and released spring forces during disassembly.
Caterpillar Cat 313D2 and 313D2 GC Excavator (Prefix GAP) Service Repair Manu...fijsekkdmdm2w
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
Caterpillar Cat 313D2 and 313D2 GC Excavator (Prefix GAP) Service Repair Manu...zan2736ban
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists over 30 detailed steps to disassemble parts like the final drive, travel motor, counterbalance valve, and other systems. Tools and safety precautions are also provided to properly disassemble components and release spring forces. The purpose is to thoroughly clean and inspect parts prior to reassembly of the excavator systems.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings, plates, valves, springs, seals, and other parts. Safety precautions are provided to properly release pressures and contain fluids during disassembly.
Massey ferguson mf 788 combine parts catalogue manualfjjskejdmdn
This document contains parts listings and descriptions for a Massey Ferguson MF 788 combine diesel engine. It includes sections for the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, timing gear, lubricating oil sump, lubricating oil filter, and other engine parts. The listings provide part numbers, quantities, descriptions, and assembly/component details for each part.
Massey ferguson mf 625 combines parts catalogue manualfjjskejdmdn
This document contains parts lists and technical specifications for Massey Ferguson MF 620/625 combines. It includes lists of parts, part numbers, quantities and descriptions for the cylinder block, cylinder head, crankshaft, and cylinder head cover. Each part is accompanied by additional details like serial number ranges and replacement part numbers.
Massey ferguson mf 620 combines parts catalogue manualfjjskejdmdn
This document contains parts lists and technical specifications for Massey Ferguson MF 620/625 combines. It includes lists of parts, part numbers, quantities and descriptions for the cylinder block, cylinder head, crankshaft, and cylinder head cover. Notes are provided on application and replacement of certain parts based on the combine's serial number or engine number.
Massey ferguson mf 515 combines (gb) parts catalogue manualfjjskejdmdn
The document provides parts listings and technical specifications for components of Massey Ferguson 510/515 combines. It includes lists of parts, part numbers, quantities and other identifying information for the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, and timing gear of MF 510/515 combines. Notes are provided to indicate application details for some parts.
Massey ferguson mf 510 combines (gb) parts catalogue manualfjjskejdmdn
This document provides parts information for a Massey Ferguson MF 510/515 combine, including the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, and timing gear. It lists over 100 individual part numbers, quantities, descriptions, and other identifying information organized into sections for each component or assembly.
More Related Content
Similar to Caterpillar cat 313 d2 excavator (prefix fap) service repair manual (fap00001 and up)
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hot/pressurized fluids. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and traction control valve. Safety notices are included throughout to warn of hazards like parts propelled by springs, hydraulic pressure, and heavy component weights. Dismantling involves draining fluids, removing seals and plates, and using various tools to separate interconnected mechanical parts.
The document provides disassembly instructions for the final drive, travel motor, and various components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hot/pressurized fluids. Dismantling requires specialty tools and careful tracking of part locations for reassembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists over 30 detailed steps to disassemble parts like the final drive, travel motor, counterbalance valve, and other systems. Tools and safety precautions are also provided to properly disassemble components and release spring forces. The purpose is to thoroughly clean and inspect parts prior to reassembly of the excavator systems.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety precautions are included to warn of hazards such as hydraulic pressure, heavy component weights, and released spring forces during disassembly.
Caterpillar Cat 313D2 and 313D2 GC Excavator (Prefix GAP) Service Repair Manu...fijsekkdmdm2w
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
Caterpillar Cat 313D2 and 313D2 GC Excavator (Prefix GAP) Service Repair Manu...zan2736ban
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists over 30 detailed steps to disassemble parts like the final drive, travel motor, counterbalance valve, and other systems. Tools and safety precautions are also provided to properly disassemble components and release spring forces. The purpose is to thoroughly clean and inspect parts prior to reassembly of the excavator systems.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings, plates, valves, springs, seals, and other parts. Safety precautions are provided to properly release pressures and contain fluids during disassembly.
Similar to Caterpillar cat 313 d2 excavator (prefix fap) service repair manual (fap00001 and up) (17)
Massey ferguson mf 788 combine parts catalogue manualfjjskejdmdn
This document contains parts listings and descriptions for a Massey Ferguson MF 788 combine diesel engine. It includes sections for the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, timing gear, lubricating oil sump, lubricating oil filter, and other engine parts. The listings provide part numbers, quantities, descriptions, and assembly/component details for each part.
Massey ferguson mf 625 combines parts catalogue manualfjjskejdmdn
This document contains parts lists and technical specifications for Massey Ferguson MF 620/625 combines. It includes lists of parts, part numbers, quantities and descriptions for the cylinder block, cylinder head, crankshaft, and cylinder head cover. Each part is accompanied by additional details like serial number ranges and replacement part numbers.
Massey ferguson mf 620 combines parts catalogue manualfjjskejdmdn
This document contains parts lists and technical specifications for Massey Ferguson MF 620/625 combines. It includes lists of parts, part numbers, quantities and descriptions for the cylinder block, cylinder head, crankshaft, and cylinder head cover. Notes are provided on application and replacement of certain parts based on the combine's serial number or engine number.
Massey ferguson mf 515 combines (gb) parts catalogue manualfjjskejdmdn
The document provides parts listings and technical specifications for components of Massey Ferguson 510/515 combines. It includes lists of parts, part numbers, quantities and other identifying information for the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, and timing gear of MF 510/515 combines. Notes are provided to indicate application details for some parts.
Massey ferguson mf 510 combines (gb) parts catalogue manualfjjskejdmdn
This document provides parts information for a Massey Ferguson MF 510/515 combine, including the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, and timing gear. It lists over 100 individual part numbers, quantities, descriptions, and other identifying information organized into sections for each component or assembly.
Massey ferguson mf 500 combine (gb) parts catalogue manualfjjskejdmdn
This document provides parts information for the cylinder block, cylinder head, crankshaft, and cylinder head cover of a Massey Ferguson MF 500 combine. It includes lists of parts with part numbers, quantities, descriptions, and notes on application and serial number ranges. Key assemblies like the cylinder block, head, crankshaft, and head cover can be ordered, and individual parts like pistons, rods, bearings, gaskets, and seals are also listed. Notes provide additional details on part application and changes over different serial number ranges.
Massey ferguson mf 430 combine parts catalogue manualfjjskejdmdn
This document provides a parts list for a Massey Ferguson 430 combine. It includes 3 tables of contents that list various systems of the combine including the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction and exhaust system, timing gear, and lubricating oil sump. Each system lists the relevant parts, part numbers, quantities, and additional part details.
Massey ferguson mf 415 combines parts catalogue manualfjjskejdmdn
This document provides part numbers and descriptions for components of the lubricating oil sump for Massey Ferguson MF 410/415 combines. It includes over 80 numbered items that make up the sump assembly, such as the sump, gaskets, bolts, gears, strainers, pumps, pipes, unions and other components. Precise part numbers are given to allow for ordering replacements. Notes provide additional details for some parts, such as applicable serial number ranges.
Massey ferguson mf 410 combines parts catalogue manualfjjskejdmdn
This document provides part numbers and descriptions for components of the lubricating oil sump for Massey Ferguson MF 410/415 combines. It includes over 80 numbered items that make up the sump assembly, such as the sump, gaskets, bolts, gears, strainers, pumps, pipes, unions and other components. Precise part numbers are given to allow for ordering replacements. Notes provide additional details for some parts, such as applicable serial number ranges.
Massey ferguson mf 400 combine (gb) parts catalogue manualfjjskejdmdn
This document provides parts information for a Massey Ferguson MF 400 combine engine. It includes lists of parts for various engine systems like the cylinder block, crankshaft, cylinder head cover, and lubricating oil sump. Each part is identified by number, description, and any relevant comments on application or changes over time. The parts lists contain technical specifications to aid in maintenance and repair of the engine.
Massey ferguson mf 330 combine parts catalogue manualfjjskejdmdn
This document provides a parts list for the cylinder block of a Massey Ferguson MF 330 combine. It contains 46 numbered items including the cylinder block, liners, plugs, bolts, and other components. Each item lists the part number, quantity, description, and any relevant comments. Tolerances or fits are indicated with an "X" next to the part number.
Massey ferguson mf 290 tractor, 387020 (gb) parts catalogue manualfjjskejdmdn
The document contains detailed parts lists and diagrams for components of a Massey Ferguson MF 290 tractor engine. It lists 56 items that make up the timing gear assembly of an A4 248 engine, including the camshaft, gears, covers, joints, screws, washers, and other individual parts. Similar details are provided for other engine assemblies like the cylinder block, cylinder head, crankshaft, air induction/exhaust systems, and cylinder head cover. The document acts as a service or repair manual containing precise part numbers and descriptions for replacing or servicing parts of the MF 290 tractor engine.
Massey ferguson mf 265 tractor, 193552 (gb) parts catalogue manualfjjskejdmdn
The document contains parts lists and technical specifications for components of a Massey Ferguson MF 265 tractor engine. It lists over 30 individual components of the engine including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft, timing gear and camshaft. Each component item is accompanied by part numbers, quantities, descriptions and any relevant comments. The level of technical detail provided suggests this is a service or repair document for mechanics working on this engine.
The document provides parts listings and descriptions for various components of a Massey Ferguson 240 tractor, including the engine, cylinder block, crankshaft, pistons, connecting rods, and cylinder head. It includes the part numbers, quantities, descriptions, and additional comments for over 50 individual parts.
Massey ferguson mf 240 tractor, 522353 (gb) parts catalogue manualfjjskejdmdn
The document appears to be parts lists and technical specifications for a Massey Ferguson MF 240 tractor. It includes lists of over 60 individual parts for components like the cylinder block, cylinder head, crankshaft, and timing gear. Each part is given an item number, part number, quantity, description, and sometimes additional comments or specifications.
Massey ferguson 1760 m compact tractor parts catalogue manualfjjskejdmdn
The document is a table of contents and service manual sections for a Massey Ferguson 1760M compact tractor. It includes sections on the engine and fuel systems, steering, drivetrain, brakes, hydraulics, electrical systems, cab, chassis, decals, wheels, implement lift system and accessories. Each section includes detailed part listings, diagrams and specifications for repairing and servicing the tractor systems.
Massey ferguson 1755 m compact tractor parts catalogue manualfjjskejdmdn
The document provides a table of contents and technical specifications for the Massey Ferguson 1755M compact tractor. It lists 12 systems of the tractor, including the engine and fuel system, steering system, drive train system, and more. Each system section includes detailed part listings, diagrams, and specifications for repair and maintenance of the tractor.
Claas temis 650 z (type t05) tractor service repair manualfjjskejdmdn
This document provides instructions for removing and installing gearbox casings and components for three types of TEMIS gearboxes. It describes:
1) Removing and installing input housing covers, main gearbox covers, and the top cover.
2) Adjusting the gear and range control levers during top cover installation.
3) Key components of the selecter rails and forks such as the forks, liners, and locking pins.
4) The gear and range controls for each gearbox type, which include mechanical levers and electro-hydraulic controls.
Claas temis 650 x (type t05) tractor service repair manualfjjskejdmdn
This document provides instructions for removing and installing various components of three different gearbox models: B13.25, B13.29, and B13.35. It describes the controls for each gearbox and provides an exploded view diagram and key. The main steps outlined are:
1. Remove the input housing and disconnect the rear axle from the main gearbox.
2. Remove the main gearbox top cover to access the selector rails and forks.
3. Mark selector positions and loosen locking bolts and wires on forks and selectors.
4. Disconnect switches and extract push buttons and balls to remove selector rails.
Claas temis 650 rx (type t05) tractor service repair manualfjjskejdmdn
This document provides instructions for removing and installing gearbox casings and components for three types of TEMIS gearboxes. It describes:
1) Removing and installing input housing covers, main gearbox covers, and the top cover.
2) Adjusting the gear and range control levers during top cover installation.
3) Key components of the selecter rails and forks such as the forks, liners, and locking pins.
4) The gear and range controls for each gearbox type, which include mechanical levers and electro-hydraulic controls.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 EXCAVATOR FAP
Configuration: 313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR7323-03 Publication Date -01/09/2015 Date Updated -14/12/2017
i06303560
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
C 8T-6699 Bolts 2
D
1P-0074 Slide Hammer Puller Gp 1
4C-5666 Threaded Adapter 1
123-6702 Backlash Gauge Gp 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
Start By:
a. Remove the final drive and the travel motor. Refer to Disassembly and Assembly Manual ,
"Final Drive and Travel Motor - Remove".
NOTICE
1/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor. The weight of the sprocket is
approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
2/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g00940682
4. Use Tooling (A) and a suitable lifting device to position the final drive and the travel motor
onto Tooling (B). The combined weight of the final drive and travel motor is approximately
170 kg (375 lb).
5. Drain the oil from the final drive into a suitable container for storage or for disposal. Refer
to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the final
drive.
6. Remove fittings (1). Remove fittings (2) from traction control valve (3).
7. Remove nine bolts (4) that secure traction control valve (3) to the final drive.
8. Use two persons to remove traction control valve (3) from the final drive. The weight of
travel brake valve (3) is approximately 27 kg (60 lb).
3/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 2 g00940716
9. Remove valve plate (5) and O-ring seal (6).
Illustration 3 g01405139
10. Use Tooling (D) to remove bearing (7).
Disassembly of the Counterbalance Valve
Illustration 4 g01405725
4/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 5 g01405227
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Position the counterbalance valve, as shown. Remove plug (8) and adapter (9).
2. Remove spring (10) and spool (11).
Illustration 6 g01405232
5/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 3. Remove relief valve assemblies (12).
Illustration 7 g01405243
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove seat (13). Seat (13) is pressed onto valve (17). Use new parts if seat (13) or valve
(17) is damaged. Do not disassemble these components. Make sure that you reuse the other
component.
5. Remove backup ring (14) and O-ring seal (15).
6. Remove O-ring seal (22).
7. Remove nut (20).
8. Remove screw (27).
9. Remove stopper (26). Remove backup ring (19) and O-ring seal (18) from stopper (19).
10. Remove valve (21), piston (25), and spring (16) from the housing.
11. Remove backup ring (23) and O-ring seal (24) from piston (25).
6/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 8 g01405284
Illustration 9 g01405299
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove covers (28) and the O-ring seals.
13. Remove springs (29), guides (30), and spool assembly (31).
7/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 10 g01405345
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
14. Remove valve (32), spring (33), and ball (34) from one end of spool (35). Repeat for the
other end of spool (35).
Illustration 11 g01405633
8/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
15. Remove plug (36), spring (38), and piston (39) from both sides of the housing assembly.
16. Remove O-ring seal (37) from each plug (36).
Note: Remove the remaining allen head bolts from the housing assembly for cleaning
purposes, if necessary. Each allen head bolt has an O-ring seal. Check the O-ring seal for
wear or for damage. Replace the O-ring seal, if necessary.
Disassembly of the Travel Motor
Illustration 12 g01405794
1. Remove O-ring seal (40) and springs (41).
9/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 13 g01405828
2. Install Tooling (C) onto piston assembly (42). Use Tooling (C) and a suitable prybar to
remove piston assembly (42) from body (43).
Illustration 14 g01405855
3. Remove O-ring seals (45) and (46) from piston assembly (42). Remove backup rings (44)
and (47) from piston assembly (42).
10/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 15 g01405867
4. Use suitable drivers or a suitable lever to remove guide assembly (48).
Illustration 16 g01405885
5. Remove O-ring seal (49) and backup ring (50) from guide assembly (48).
11/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 17 g01406117
6. Remove four separator plates (51) and four friction plates (52). Note the alternating order of
separator plates (51) and friction plates (52) for assembly purposes.
Note: Do not allow the components of barrel assembly (53) to come apart while you
remove barrel assembly (53). The components of barrel assembly (53) must be reinstalled
into the original positions.
Note: Oil will drain from the final drive. Place a suitable container under the final drive for
storage or disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for
the fluid capacity of the final drive.
7. Position the final drive horizontally.
8. Remove barrel assembly (53).
12/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 18 g01406180
Note: Mark the component locations for assembly purposes before you disassemble barrel
assembly (53).
9. Remove piston assemblies (54) and retainer (55) from barrel assembly (53).
Illustration 19 g01406210
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Remove retainer (56), spacer (57), and springs (58) from barrel assembly (53).
13/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 20 g01406263
11. Put location marks on cam plate (59) for assembly purposes. Make sure that the thick end of
cam plate (59) is adjacent to the opening that is across body (43). Remove cam plate (59).
Illustration 21 g01406329
Illustration 22 g01406338
14/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove piston (60) and spring (62).
13. Remove key (61).
Disassembly of the Final Drive
Illustration 23 g01406376
1. Use a suitable lifting device to position the final drive on Tooling (B), as shown. The weight
of the final drive is approximately 200 kg (441 lb).
2. Remove plugs (63). Remove the O-ring seals from plugs (63). Check the O-ring seals for
wear or for damage. Replace the O-ring seals, if necessary.
3. Remove bolts (65). Remove cover (64).
15/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 24 g01406386
4. Raise the temperature of bolts (66) in order to loosen the thread sealant.
5. Remove bolts (66) and plate (67).
Illustration 25 g01406397
6. Remove sun gear (68).
16/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 26 g01406400
7. Attach Tooling (A) and a suitable lifting device to carrier assembly (69). Remove carrier
assembly (69), planetary gear assembly (70), and bearing assembly (71) as a unit.
Illustration 27 g01406789
8. Remove planetary gear (70) and bearing assembly (71) from carrier assembly (69). Remove
the remaining planetary gears (70) and bearings (71).
Illustration 28 g01406822
9. Remove sun gear (72).
17/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 10. Raise the temperature of bolts (73) in order to loosen the thread sealant. Remove bolts (73).
Remove plate (74).
Illustration 29 g01406850
11. Remove retaining ring (75) from sun gear (72). Check retaining ring (75) for wear or for
damage. Replace retaining ring (75), if necessary.
Illustration 30 g01406853
12. Remove planetary gear (76).
18/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 31 g01406875
13. Remove bearing (77), race (78), and thrust washer (79).
14. Repeat Steps 12 and 13 in order to remove the remaining planetary gear assemblies.
Illustration 32 g01406882
15. Remove bolt (80) and plate (81).
19/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 33 g01406885
Illustration 34 g01406886
16. Use Tooling (H) to remove nut (82).
Illustration 35 g01406906
17. Install Tooling (A) and a suitable lifting device to housing (83). The weight of housing (83)
is approximately 35 kg (77 lb).
18. Remove housing (83) from body assembly (84).
20/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 36 g01406912
19. Remove Duo-Cone Seal Gp seal (85) from the body assembly. Remove the Duo-Cone Seal
Gp seal from the housing.
Illustration 37 g01407100
20. Remove both bearings (86) from housing (83).
21/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 38 g01407089
21. Remove both bearings (87) from housing (83).
Illustration 39 g01407115
22. Position body assembly (84) horizontally. Remove shaft assembly (88), the bearing, and the
retaining ring.
22/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 40 g01407144
23. Use Tooling (G) to remove retaining ring (89) from shaft assembly (88).
Illustration 41 g01407161
24. Use Tooling (E), Tooling (F), and a suitable press to remove bearing (90).
Illustration 42 g01407166
25. Remove lip seal (91) from the body assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 14 23:52:49 UTC+0800 2020
23/23
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 EXCAVATOR FAP
Configuration: 313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR7323-03 Publication Date -01/09/2015 Date Updated -14/12/2017
i07219742
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-5474 M16x2x24 mm Lifting Eye Assembly 2
B 1P-2420 Transmission Repair Stand 1
C 8H-0663 Bearing Puller Assembly 1
D 422-5473 M12x1.75x21 mm Lifting Eye Assembly 2
E 422-5472 M10x1.5x16 mm Lifting Eye Assembly 2
F 1U-9895 Crossblock 1
Start By:
a. Remove the final drive and the travel motor assembly.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/22
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor assembly. The weight of the
sprocket is approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
Illustration 1 g06256385
4. Use Tooling (A) and a suitable lifting device to position final drive assembly (1) onto
Tooling (B). The weight of final drive assembly (1) is approximately 163 kg (360 lb).
2/22
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 5. Drain the oil from final drive assembly (1) into a suitable container for storage or for
disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity
of the final drive.
Illustration 2 g06256798
6. Remove plug (2), plugs (3), and the O-ring seals.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 3 g06256843
3/22
313D2 & 313D2 GC Excavators FAP00001-UP (MACHINE) POWERED BY C4.4 E...
2020/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...