The document provides instructions for removing and installing the flywheel housing and crankshaft front seal of a C4.2 engine. It describes:
1) Using various tools to remove the flywheel housing, which includes removing bolts and dowels and extracting the oil seal.
2) Cleaning surfaces and installing a new gasket and oil seal when reinstalling the flywheel housing.
3) Drilling holes in the crankshaft front seal and pulling it out using a slide hammer tool.
4) Applying oil and using a seal installer tool to carefully replace the crankshaft front seal.
Caterpillar cat 313 d excavator (prefix wpk) service repair manual (wpk00001 ...fjskekdmjekm
The document provides instructions for removing and installing the flywheel housing and crankshaft front seal of a C4.2 engine. It describes:
1) Using various tools to remove the flywheel housing, which includes removing bolts and dowels and extracting the oil seal.
2) Cleaning surfaces and installing a new gasket and oil seal when reinstalling the flywheel housing.
3) Drilling holes in the crankshaft front seal and pulling it out using a slide hammer tool.
4) Applying oil and using a seal installer tool to carefully replace the crankshaft front seal.
Caterpillar cat 314 d lcr excavator (prefix sbp) service repair manual (sbp00...fjskekdmjekm
This document provides instructions for removing and installing the crankshaft rear seal, flywheel housing, and crankshaft pulley on a Caterpillar C4.2 engine. The removal procedures describe using various tools to drill holes in the crankshaft rear seal, remove the seal and wear sleeve, and remove bolts to take off the flywheel housing. The installation sections explain cleaning and applying compounds, installing new seals and gaskets, and tightening bolts while positioning components correctly.
Caterpillar cat 314 d lcr excavator (prefix wln) service repair manual (wln00...soeldksejdksem
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR and 314D LCR Excavator, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve with a chisel if needed, and installing with a driver and ensuring proper torque.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes, and installing the new seal with a front seal installer.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 336 d l excavator (prefix mds) service repair manual (mds0000...fksjksmmde
The document provides instructions for disassembling and assembling a piston pump. Key steps include:
1. Removing various components like the head, O-rings, pistons, and bearings.
2. Using tools like retaining ring pliers and a driver group to remove springs and retaining rings.
3. Taking safety precautions as parts are under spring tension.
4. Cleaning all parts thoroughly before assembly.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 312 d l excavator (prefix ska) service repair manual (ska0000...pfiskdmjekm
- The document provides instructions for removing and installing a flywheel, flywheel housing, and crankshaft rear seal on a Caterpillar 312D L excavator.
- It describes the required tools and multi-step procedures, which include removing bolts, brackets, and other components to access the parts. Special care must be taken to avoid damage and contain fluids.
- The installation procedures describe cleaning and applying compounds to mating parts, using installing tools and levers to correctly position the new parts, and reinstalling other removed components once complete.
Caterpillar cat 313 d excavator (prefix wpk) service repair manual (wpk00001 ...fjskekdmjekm
The document provides instructions for removing and installing the flywheel housing and crankshaft front seal of a C4.2 engine. It describes:
1) Using various tools to remove the flywheel housing, which includes removing bolts and dowels and extracting the oil seal.
2) Cleaning surfaces and installing a new gasket and oil seal when reinstalling the flywheel housing.
3) Drilling holes in the crankshaft front seal and pulling it out using a slide hammer tool.
4) Applying oil and using a seal installer tool to carefully replace the crankshaft front seal.
Caterpillar cat 314 d lcr excavator (prefix sbp) service repair manual (sbp00...fjskekdmjekm
This document provides instructions for removing and installing the crankshaft rear seal, flywheel housing, and crankshaft pulley on a Caterpillar C4.2 engine. The removal procedures describe using various tools to drill holes in the crankshaft rear seal, remove the seal and wear sleeve, and remove bolts to take off the flywheel housing. The installation sections explain cleaning and applying compounds, installing new seals and gaskets, and tightening bolts while positioning components correctly.
Caterpillar cat 314 d lcr excavator (prefix wln) service repair manual (wln00...soeldksejdksem
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR and 314D LCR Excavator, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve with a chisel if needed, and installing with a driver and ensuring proper torque.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes, and installing the new seal with a front seal installer.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 336 d l excavator (prefix mds) service repair manual (mds0000...fksjksmmde
The document provides instructions for disassembling and assembling a piston pump. Key steps include:
1. Removing various components like the head, O-rings, pistons, and bearings.
2. Using tools like retaining ring pliers and a driver group to remove springs and retaining rings.
3. Taking safety precautions as parts are under spring tension.
4. Cleaning all parts thoroughly before assembly.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 312 d l excavator (prefix ska) service repair manual (ska0000...pfiskdmjekm
- The document provides instructions for removing and installing a flywheel, flywheel housing, and crankshaft rear seal on a Caterpillar 312D L excavator.
- It describes the required tools and multi-step procedures, which include removing bolts, brackets, and other components to access the parts. Special care must be taken to avoid damage and contain fluids.
- The installation procedures describe cleaning and applying compounds to mating parts, using installing tools and levers to correctly position the new parts, and reinstalling other removed components once complete.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...JayHaines2
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document contains illustrations and specifies any required tools. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fjskekfseik
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 313 d excavator (prefix wpk) service repair manual (wpk00001 ...fjjskejdmdn
The document provides instructions to remove the idler gear from the front gear group of a C4.2 engine. It describes:
1. Using a puller tool to remove the idler gear from the front housing.
2. Cleaning the component parts and ensuring they are free from contaminants before installation to prevent premature wear.
3. Reinstalling the idler gear by pressing it into place in the front housing using an installer tool.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
Caterpillar cat 313 d excavator (prefix wpk) service repair manual (wpk00001 ...ikdkkdmdmdm
The document provides instructions for removing and installing various components of the C4.2 engine for Caterpillar built machines, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts, cleaning surfaces, and installing replacement components along with specified torques.
The document provides instructions for removing the idler gear from the front gear group of a C4.2 engine. It outlines the necessary tools and steps to:
1. Remove the crankshaft pulley and flywheel housing to access the front gear group.
2. Use a puller tool to remove the idler gear from the front gear group housing.
3. Inspect dowel pins and clean mating surfaces before reinstalling replacement idler gear.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various components of the C4.2 engine for Caterpillar built machines, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts, cleaning surfaces, and installing replacement components along with specified torques.
The document provides instructions for removing and installing the idler gear from the front gear group of a C4.2 engine. Key steps include using tools to remove the idler gear housing, removing the idler gear, and cleaning mating surfaces before installing a new idler gear and housing gasket. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
The document provides instructions for removing and installing the idler gear from the front gear group of a C4.2 engine. Key steps include using tools to remove the idler gear housing, removing the idler gear, and cleaning mating surfaces before installing a new idler gear and housing gasket. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
Caterpillar cat 314 d cr excavator (prefix wln) service repair manual (wln000...fjjskekdmmse
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator. Specifically, it details how to remove and install the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the engine's gear group. The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided to keep parts clean and contain fluids.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...JayHaines2
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document contains illustrations and specifies any required tools. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fjskekfseik
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 313 d excavator (prefix wpk) service repair manual (wpk00001 ...fjjskejdmdn
The document provides instructions to remove the idler gear from the front gear group of a C4.2 engine. It describes:
1. Using a puller tool to remove the idler gear from the front housing.
2. Cleaning the component parts and ensuring they are free from contaminants before installation to prevent premature wear.
3. Reinstalling the idler gear by pressing it into place in the front housing using an installer tool.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
Caterpillar cat 313 d excavator (prefix wpk) service repair manual (wpk00001 ...ikdkkdmdmdm
The document provides instructions for removing and installing various components of the C4.2 engine for Caterpillar built machines, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts, cleaning surfaces, and installing replacement components along with specified torques.
The document provides instructions for removing the idler gear from the front gear group of a C4.2 engine. It outlines the necessary tools and steps to:
1. Remove the crankshaft pulley and flywheel housing to access the front gear group.
2. Use a puller tool to remove the idler gear from the front gear group housing.
3. Inspect dowel pins and clean mating surfaces before reinstalling replacement idler gear.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various components of the C4.2 engine for Caterpillar built machines, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts, cleaning surfaces, and installing replacement components along with specified torques.
The document provides instructions for removing and installing the idler gear from the front gear group of a C4.2 engine. Key steps include using tools to remove the idler gear housing, removing the idler gear, and cleaning mating surfaces before installing a new idler gear and housing gasket. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
The document provides instructions for removing and installing the idler gear from the front gear group of a C4.2 engine. Key steps include using tools to remove the idler gear housing, removing the idler gear, and cleaning mating surfaces before installing a new idler gear and housing gasket. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
Caterpillar cat 314 d cr excavator (prefix wln) service repair manual (wln000...fjjskekdmmse
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator. Specifically, it details how to remove and install the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the engine's gear group. The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided to keep parts clean and contain fluids.
- The document provides instructions for removing and installing the idler gear from the front gear group of a C4.2 engine.
- To remove the idler gear, the front housing must first be removed, then the idler gear bolt, thrust plate, and idler gear are taken off the idler gear shaft.
- A puller tool is then used to remove the idler shaft from the front housing.
- The document provides instructions for removing and installing the idler gear from the front gear group of a C4.2 engine.
- To remove the idler gear, the front housing must first be removed, then the idler gear bolt, thrust plate, and idler gear are taken off the idler gear shaft.
- A puller tool is then used to remove the idler shaft with the idler gear.
- The document provides instructions for removing and installing the idler gear from the front gear group of a C4.2 engine.
- To remove the idler gear, the front housing must first be removed, then the idler gear bolt, thrust plate, and idler gear are taken off the idler gear shaft.
- A puller tool is then used to remove the idler shaft from the front housing.
Caterpillar cat 314 d cr excavator (prefix wln) service repair manual (wln000...fjjsekdmme
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires draining fluids, removing mounting bolts and hardware, and installing a new gasket.
- Removing and installing the crankshaft pulley, which requires removing a nut and washer, pulling the pulley off using a puller, and replacing the wear sleeve if needed before reinstallation.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes in the seal for extraction, being careful not to damage the crankshaft flange.
- Installing the new cr
Caterpillar cat 314 d lcr excavator (prefix wln) service repair manual (wln00...fhsejkdkmem
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the flywheel housing which requires removing bolts and installing replacement gaskets.
2) Removing the crankshaft pulley which requires removing nuts and washers using pulling tools.
3) Removing the crankshaft front seal which requires drilling holes and pulling it out evenly using a slide hammer tool.
Caterpillar cat 314 d lcr excavator (prefix wln) service repair manual (wln00...fhsjekkdkem
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the flywheel housing which requires removing bolts and installing replacement gaskets.
2) Removing the crankshaft pulley which requires removing nuts and installing replacement seals.
3) Removing the idler gear which requires aligning timing marks and using pullers to remove the gear and bushings.
Similar to Caterpillar cat 313 d excavator (prefix wpk) service repair manual (wpk00001 and up) (20)
Mc cormick t series compact (2001 2009) - ct00 - t60f tractor service repair ...ifosodkmsme
This document contains parts lists and component information for repairing and replacing parts for tractor models. It includes lists of components, reference numbers, part numbers, descriptions and other technical specifications. Quantity requirements and application details are provided for components that may be needed for different tractor models or serial number ranges.
Mc cormick g max tier 3 new cab (2012- ) - rp75 - 125 tractor service repair ...ifosodkmsme
This document provides exploded diagrams and part lists for engine components of a McCormick G-MAX Tier 3 tractor, including the cylinder head, crankcase, pistons, connecting rods, camshaft, fuel pump, and other parts. Each component drawing includes reference numbers linked to replacement part numbers and quantities needed. The summary provides high-level information on the content and purpose of the document in 3 sentences or less.
Mc cormick g max iveco tier 3 (2007-2012) - rp74 - 145 tractor service repair...ifosodkmsme
This document provides parts information for an Iveco G-MAX engine. It includes exploded diagrams of engine components and lists replacement parts with corresponding part numbers. The parts listed are for the engine block, cylinder head, valve train, fuel system, turbocharger, and other internal engine components. Specifications are provided for markets in North America and Europe.
Mc cormick g max (2008- ) - rp72 - 160 tractor service repair manualifosodkmsme
This document contains parts lists and technical specifications for components of an engine. It includes identification numbers, names and descriptions of parts like pistons, liners, gears, seals, valves and other engine components. Quantities, replacement codes and other technical details are provided for servicing and ordering the correct replacement parts.
Mc cormick gm tier 3 (2009 ) - rs12 - 55 tractor service repair manualifosodkmsme
This document contains parts lists and assembly instructions for engine components. It lists over 60 individual parts, including bolts, plugs, gaskets, pistons, rods, bearings, and other engine parts. For each part it specifies the part number, quantity needed, and tasks associated with the part like replacement or overhaul. It also includes assembly notes and specifies the tractor model and year the parts are associated with.
Mc cormick gm tier 3 (2009 ) - rs12 - 50 tractor service repair manualifosodkmsme
This document provides a list of components for repairing or replacing parts of a tractor transmission. It includes over 50 individual parts needed for the transmission assembly/overhaul, with details like part numbers, descriptions, quantities and replacement instructions. Each part is labeled as related to the transmission assembly ("T-A"). The list is accompanied by notes about component identification, quantity breakdowns for tractor models, and references to other pages or manuals.
Mc cormick gm tier 3 (2009 ) - rs12 - 45 tractor service repair manualifosodkmsme
This document provides a list of components for engine replacement or overhaul for a tractor model. It includes over 50 individual part items, each with details like part number, description, quantity needed and application (e.g. engine T-A). The parts are for systems like the cylinder head, pistons, flywheel, fuel pump and injection components. Precision replacement parts are also indicated for proper sizing (e.g. oversized or undersized variants). The document appears to be from a repair manual or parts catalog to facilitate maintenance and repairs for this tractor model.
Mc cormick gm tier 3 (2009 ) - rs12 - 40 tractor service repair manualifosodkmsme
This document contains parts lists and assembly diagrams for components of an agricultural tractor. It includes lists of replacement parts for engines, transmissions, hydraulics, and other systems. Each part is identified by number and name, and specifies whether it is for tractor model T-A or T-B. Quantity required and installation notes are also provided. The parts appear to be for a GM tier 3 tractor from 2009 or later.
Mc cormick gm series tier 2 (2003 2008) - rs11 - gm55 tractor service repair ...ifosodkmsme
This document contains parts listings and information for engine components. It includes listings of over 30 individual parts for an engine, with information on each part including part number, description, quantity, and whether it is for tractor models T-A or T-B. The document also provides identifying information at the top, including the tractor model series and manufacturer.
Mc cormick gm series tier 2 (2003 2008) - rs11 - gm50 tractor service repair ...ifosodkmsme
This document contains parts lists and assembly instructions for engine components of GM Series Tier 2 tractors from 2003-2008. It includes over 50 individual part numbers with descriptions of engine parts like pistons, rods, bearings, gaskets, plugs, bolts and other hardware. Quantity requirements and replacement part identifiers are provided. The parts are grouped according to their location in the engine and assembly sequence.
Mc cormick fxl tier 3 (2008 2009) - rp53 - f105 gexl tractor service repair m...ifosodkmsme
This document contains a list of engine components with corresponding part numbers. It includes items like cylinder blocks, pistons, gears, pumps, nozzles and other engine parts. Quantities and references to other part numbers are provided. The document also notes that some items are replacements or not serviced and should be ordered. It relates to a Perkins engine that is part of a McCormick tractor.
Mc cormick fxl tier 3 (2008 2009) - rp53 - f100 gexl tractor service repair m...ifosodkmsme
This document contains a list of engine components with identification numbers, descriptions, and other technical specifications. It includes items like cylinder blocks, pistons, gears, shafts, gaskets, screws and other parts. Each item lists the reference number, quantity, identification code and other information. The document appears to be an inventory or parts listing for an engine, with details to help with ordering or identifying replacement components.
Massey ferguson mf8130 tractor parts catalogue manualifosodkmsme
This document provides exploded view diagrams and part lists for components of a Massey Ferguson 8130 tractor engine, including the cylinder block, crankshaft, cylinder head, rocker shaft, and turbocharger. It lists over 50 individual parts for each assembly, along with part numbers, quantities, descriptions, and notes. The diagrams show the assembly of components and their positions relative to each other.
Massey ferguson mf8120 tractor parts catalogue manualifosodkmsme
This document provides parts information for the cylinder head of a Massey Ferguson 8120 tractor. It contains 51 numbered items describing the individual parts that make up the cylinder head assembly, including the head, guides, plugs, seals, springs, caps, inserts, valves and screws. The document specifies the part numbers, quantities and any replacement comments for each part listed.
Massey ferguson mf7724 mf7724 s tractor (dyna vt) (f092038 9999999) or (m77...ifosodkmsme
This document contains parts listings and diagrams for a Massey Ferguson 7724/7724S tractor engine. It includes over 20 pages detailing over 150 individual engine parts, grouped by location in the engine (cylinder block, timing gears, flywheel, crankshaft, etc.). Each part is listed by number, name, quantity used, and other identifying information. Diagrams are provided to illustrate where each part is located in the engine.
Kubota b2410 hsdb tractor parts catalogue manualifosodkmsme
The document provides instructions and definitions for parts books. It explains that the heading on parts pages will match the picture pages. It defines the column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability codes. It also provides notes about country codes that may be included.
Kubota b2410 hsd tractor parts catalogue manualifosodkmsme
This parts book page provides information on crankcase parts for a tractor model. It lists 20 individual parts that make up the crankcase assembly, including the composite crankcase, caps, plugs, pins, bushes and bolts. Specifications are provided such as part number, description, quantity used, serial number applicability, interchangeability, remarks and weight.
Kubota b2400 hse tractor parts catalogue manualifosodkmsme
The document provides instructions and definitions for parts books. It lists the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included and explains what parts are different in other countries. The bottom section is an index of parts for a B2400HSE tractor model organized by system and subsystems.
Komatsu wa200 pz 6 wheel loader service repair manual sn70136 and upifosodkmsme
This document provides information about Komatsu wheel loaders, including:
- The shop manual covers models WA200-6 and WA200PZ-6.
- Sections include specifications, maintenance procedures, testing and adjustments, troubleshooting, and electrical systems.
- The manual contains diagrams of systems like the engine, power train, steering, brakes, hydraulics, and electrical wiring.
- Troubleshooting sections provide failure codes, testing procedures, and potential causes of issues.
Komatsu wa200 pz 6 wheel loader service repair manual (sn 70001 and up)ifosodkmsme
This document provides a shop manual for wheel loaders models WA200 and WA200PZ-6. It contains sections on specifications, maintenance standards, testing and adjusting procedures, and troubleshooting. The manual covers the engine and cooling system, power train, steering, brakes, undercarriage, hydraulics, work equipment, cab, electrical systems, standard values, and more. Troubleshooting sections include failure code tables, general troubleshooting information, and procedures for addressing individual failure codes displayed on the machine monitor.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D EXCAVATOR WPK
Configuration: 313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 19:13:39 UTC+0800 2020
4/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D EXCAVATOR WPK
Configuration: 313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 4 g01377941
2. Ensure that baffle plate (5) is oriented, as shown.
Illustration 5 g00604778
3. Position crankshaft pulley (3) onto the engine.
4. Install washer (2) and nut (1). Use Tooling (B) in order to tighten nut (1) to a torque of
707.5 ± 57.5 N·m (522 ± 42 lb ft).
5. Install the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 19:14:36 UTC+0800 2020
4/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D EXCAVATOR WPK
Configuration: 313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742689
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
Typical Example
1. Drill three evenly spaced 3.0 mm (0.12 inch) holes in crankshaft front seal (1).
2. Use Tooling (A) in order to remove crankshaft front seal (1). Remove the seal evenly by
alternating the position of Tooling (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 19:15:32 UTC+0800 2020
2/2313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D EXCAVATOR WPK
Configuration: 313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742692
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00612743
Typical Example
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Use Tooling (A) in order to install new crankshaft front seal (1) in the front housing.
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 19:16:29 UTC+0800 2020
2/2313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D EXCAVATOR WPK
Configuration: 313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g01374810
Illustration 6 g01374811
5. The following items are components of Tooling (A).
◦ 9U-6147 Stud (9)
◦ 6V-8231 Nut (10)
◦ 9U-6146 Sleeve Assembly (11)
◦ 8T-4244 Nut (12)
6. Use Tooling (A) in order to remove idler shaft (8) (not shown) from the cylinder block.
Check idler shaft (8) for wear and damage. Replace idler shaft (8), if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
◦ In order to remove camshaft gear (3), refer to Disassembly and Assembly, "Camshaft
- Remove".
◦ In order to remove fuel injection pump gear (1), refer to Disassembly and Assembly,
"Fuel Injection Pump - Remove".
◦ In order to remove the gear from the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Remove".
◦ In order to remove crankshaft gear (4), refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 19:17:26 UTC+0800 2020
4/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D EXCAVATOR WPK
Configuration: 313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879402
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
a 1p-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01374804
1. Use Tooling (A) and a suitable press in order to install a new bushing (7) (not shown), if the
bushing was removed.
Illustration 2 g01374810
2. Lower the temperature of idler shaft (8) . Install idler shaft (8) (not shown) onto the cylinder
block.
Note: When idler shaft (8) is installed, ensure that the oil hole of idler shaft (8) is up.
Illustration 3 g01374827
3. Install idler gear (2) onto idler shaft (8) .
2/5313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
Illustration 5 g01374789
4. Install thrust plate (6) onto the idler shaft.
5. Install the washer and idler gear bolt (5) onto thrust plate (6) . Tighten idler gear bolt (5) to a
torque of 34 ± 5 N·m (25 ± 4 lb ft).
3/5313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Note: See the following list for the installation of the other gears in the front gear group.
◦ In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Install".
◦ In order to install the fuel injection pump gear, refer to Disassembly and Assembly,
"Fuel Injection Pump - Install".
◦ In order to install the gear to the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Install".
◦ In order to install the crankshaft front gear, refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Illustration 6 g01374841
6. Install a dial indicator and rotate idler gear (2) back and forth in order to measure backlash.
Refer to Table 3.
Table 2
Item Standard at Assembly Service Limit
Backlash of crankshaft gear and
idler gear
0.510 to 0.157 mm (0.0201 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of camshaft gear and
idler gear
0.520 to 0.158 mm (0.0205 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of fuel injection pump
gear and idler gear
0.0560 to 0.205 mm (0.0022 to
0.0081 inch)
0.250 mm (0.0098
inch)
4/5313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. End play of idler gear
0.050 to 0.200 mm (0.0020 to
0.0079 inch)
0.350 mm (0.0138
inch)
Clearance between idler gear
bushing and shaft
0.009 to 0.050 mm (0.0004 to
0.0020 inch)
0.100 mm (0.0039
inch)
Illustration 7 g01374874
7. Measure the end play of idler gear (2) with a feeler gauge. Refer to Table 3.
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 19:18:23 UTC+0800 2020
5/5313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D EXCAVATOR WPK
Configuration: 313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02743335
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
c. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
d. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374908
1. Loosen hose clamp (1) that secures hose (2) to the front housing.
2. Disconnect hose (2) from the front housing.
Illustration 2 g00605985
3. Remove bolts (3) and the washers that hold front housing (4) to the plate and the cylinder
block.
2/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 4. Remove six bolts (5) (not shown) and the washers that mount front housing (4) to the oil
pan.
Illustration 3 g00606002
5. Remove bolts (6) and the washers that mount front housing (4) to front plate (8) and the
cylinder block.
6. Use two people in order to remove front housing (4) from the cylinder block and front plate
(8). The weight of front housing (4) is approximately 20 kg (45 lb).
Note: Check the condition of gasket (7) (not shown) for the engine oil pan. If gasket (7) is
damaged, it may be necessary to replace gasket (7). Refer to Disassembly and Assembly,
"Engine Oil Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
3/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Illustration 4 g01377884
7. Remove baffle plate (9).
Illustration 5 g01377894
8. Use Tooling (A) in order to remove crankshaft front seal (10) (not shown) from front
housing (4), if necessary.
9. Check the teeth of the timing gears for the following items: wear, nicks, chips and uneven
contact. Check the keyway for wear or damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 19:19:19 UTC+0800 2020
4/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D EXCAVATOR WPK
Configuration: 313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879387
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets, and the seals for wear or for damage. Replace the components, if
necessary.
1/4313D Excavator WPK00001-UP (MACHINE) POWERED BY C4.2 Engine(SEBP621...
2020/5/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...