This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve if needed.
- Removing the crankshaft front seal by drilling holes and pulling it off with a slide hammer puller.
Caterpillar cat 312 c l excavator (prefix cba) service repair manual (cba0120...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for each
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
The document provides instructions for installing a crankshaft rear seal on a 3064 engine. It lists the required tools which include an installer, locator, bolts, and washer. The instructions describe using a primer and retaining compound on the mating parts. It then details using Tool A to install a new wear sleeve with seal by placing it in the installer and pushing it onto the crankshaft until fully seated. It concludes by checking the seal installation and reinstalling the flywheel.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...tuzhiyou2
The document provides instructions for installing a crankshaft rear seal on a 3064 engine. It lists the required tools which include an installer, locator, bolts, and washer. The instructions describe using a primer and retaining compound on the mating parts. It then details using Tool A to install a new wear sleeve with seal by placing it in the installer and pushing it onto the crankshaft until fully seated. It concludes by checking the seal installation and reinstalling the flywheel.
1. The document provides instructions for removing and installing various parts of a 3064 engine, including the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear.
2. The procedures include a list of required tools and step-by-step instructions describing how to remove and install each part while keeping parts clean to prevent damage.
3. Technicians are advised to contain fluids, properly dispose of fluids, and apply sealant or oil to mating surfaces during installation to ensure correct assembly and prevent leaks.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...qfyc504378
1. The document provides instructions for removing and installing various parts of a 3064 engine, including the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear.
2. The procedures include a list of required tools and step-by-step instructions describing how to remove and install each part while keeping parts clean to prevent damage.
3. Technicians are advised to contain fluids, properly dispose of fluids, and apply sealant or oil to mating surfaces during installation to ensure correct assembly and prevent leaks.
1. The document provides instructions for removing and installing various parts of a 3064 engine, including the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear.
2. The procedures include a list of required tools and step-by-step instructions describing how to remove and install each part while keeping parts clean to prevent damage.
3. Technicians are advised to contain fluids, properly dispose of fluids, and apply sealant or oil to mating surfaces during installation to ensure correct assembly and prevent leaks.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...lituo39419496
1. The document provides instructions for removing and installing various parts of a 3064 engine, including the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear.
2. The procedures include a list of required tools and step-by-step instructions describing how to remove and install each part while keeping parts clean to prevent damage.
3. Technicians are advised to contain fluids, properly dispose of fluids, and apply sealant or oil to mating surfaces during installation to ensure correct assembly and prevent leaks.
Caterpillar cat 312 c l excavator (prefix cba) service repair manual (cba0120...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for each
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
The document provides instructions for installing a crankshaft rear seal on a 3064 engine. It lists the required tools which include an installer, locator, bolts, and washer. The instructions describe using a primer and retaining compound on the mating parts. It then details using Tool A to install a new wear sleeve with seal by placing it in the installer and pushing it onto the crankshaft until fully seated. It concludes by checking the seal installation and reinstalling the flywheel.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...tuzhiyou2
The document provides instructions for installing a crankshaft rear seal on a 3064 engine. It lists the required tools which include an installer, locator, bolts, and washer. The instructions describe using a primer and retaining compound on the mating parts. It then details using Tool A to install a new wear sleeve with seal by placing it in the installer and pushing it onto the crankshaft until fully seated. It concludes by checking the seal installation and reinstalling the flywheel.
1. The document provides instructions for removing and installing various parts of a 3064 engine, including the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear.
2. The procedures include a list of required tools and step-by-step instructions describing how to remove and install each part while keeping parts clean to prevent damage.
3. Technicians are advised to contain fluids, properly dispose of fluids, and apply sealant or oil to mating surfaces during installation to ensure correct assembly and prevent leaks.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...qfyc504378
1. The document provides instructions for removing and installing various parts of a 3064 engine, including the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear.
2. The procedures include a list of required tools and step-by-step instructions describing how to remove and install each part while keeping parts clean to prevent damage.
3. Technicians are advised to contain fluids, properly dispose of fluids, and apply sealant or oil to mating surfaces during installation to ensure correct assembly and prevent leaks.
1. The document provides instructions for removing and installing various parts of a 3064 engine, including the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear.
2. The procedures include a list of required tools and step-by-step instructions describing how to remove and install each part while keeping parts clean to prevent damage.
3. Technicians are advised to contain fluids, properly dispose of fluids, and apply sealant or oil to mating surfaces during installation to ensure correct assembly and prevent leaks.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...lituo39419496
1. The document provides instructions for removing and installing various parts of a 3064 engine, including the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear.
2. The procedures include a list of required tools and step-by-step instructions describing how to remove and install each part while keeping parts clean to prevent damage.
3. Technicians are advised to contain fluids, properly dispose of fluids, and apply sealant or oil to mating surfaces during installation to ensure correct assembly and prevent leaks.
Caterpillar Cat 312C and 312C L Excavator (Prefix BWH) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and seal installation using a installer tool.
- Flywheel housing removal by lifting it off with straps after removing bolts, and installation by cleaning the mating surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and installing by securing with a washer and nut.
Caterpillar Cat 312C and 312C L Excavator (Prefix BWH) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. The installation procedure specifies cleaning the crankshaft and pulley, applying retaining compound, and pressing the pulley onto the crankshaft with an installer tool. Torque specifications are provided for securing bolts during reassembly.
Caterpillar Cat 312C L Excavator (Prefix BWH) Service Repair Manual (BWH00001...fusjekkdmdmd2w
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and seal installation using a installer tool.
- Flywheel housing removal by lifting it off with straps after removing bolts, and installation by cleaning the mating surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and installing by securing with a washer and nut.
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and seal installation using a installer tool.
- Flywheel housing removal by lifting it off with straps and removing bolts, and installation by cleaning the mating surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and installing by securing with a washer and nut.
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. The installation procedure specifies cleaning the crankshaft and pulley, applying retaining compound, and pressing the pulley onto the crankshaft with an installer tool. Torque specifications are provided for securing bolts during reinstallation.
Caterpillar Cat 312C L Excavator (Prefix BWH) Service Repair Manual (BWH00001...f8usejkddmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and installation using a installer tool and retaining compound.
- Flywheel housing removal by lifting it off with straps after removing bolts, and installation by cleaning surfaces and securing with new bolts.
- Crankshaft pulley removal using a puller and chisel if needed, and installation by positioning it and tightening the nut to the specified torque.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...idkkdmmd
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. The installation procedure specifies cleaning the crankshaft and pulley, applying retaining compound, and pressing the pulley onto the crankshaft with an installer tool. Torque specifications are provided for securing bolts during reinstallation.
Caterpillar Cat 312C L Excavator (Prefix BWH) Service Repair Manual (BWH00001...8ufjsekddm8u
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and seal installation using a installer tool.
- Flywheel housing removal by lifting it off with straps after removing bolts, and installation by cleaning the mating surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and chisel if needed, and installation by positioning it and securing with a washer and nut.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336F and 336F L Excavator (Prefix DSW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 345D L Excavator (Prefix JKN) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, bearings and other components into the travel motor housing and barrel. Measurements are taken throughout to ensure proper assembly. The travel motor is then installed on the excavator and filled with the correct oil type.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar Cat 336E L Excavator (Prefix BZY) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstalling parts. Special care must be taken when handling springs or parts under spring force to avoid injury.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It describes 37 steps to disassemble the final drive by removing gears, shafts, housings, seals and other components. It then describes 34 steps to reassemble the final drive, including pressing in new bearings, installing seals, adjusting bearing preload with shims, and applying threadlocker to bolts. Precise tools and lifting devices are required due to the heavy weights of up to 550 kg involved.
Caterpillar Cat 336E L Excavator (Prefix DPX) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor on a 336E L excavator. The disassembly process involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and ensuring proper alignment of components.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fskekkdmdmdm3e
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It describes removing over 30 components of the travel motor including the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates and more.
3) Detailed illustrations are provided to accompany each step showing how to remove each component using the recommended tools.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, in reverse order, including attaching lifting devices, positioning the assembly, and reinstalling hoses and covers. Tools and torque specifications are provided.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
More Related Content
Similar to Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual Instant Download.pdf
Caterpillar Cat 312C and 312C L Excavator (Prefix BWH) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and seal installation using a installer tool.
- Flywheel housing removal by lifting it off with straps after removing bolts, and installation by cleaning the mating surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and installing by securing with a washer and nut.
Caterpillar Cat 312C and 312C L Excavator (Prefix BWH) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. The installation procedure specifies cleaning the crankshaft and pulley, applying retaining compound, and pressing the pulley onto the crankshaft with an installer tool. Torque specifications are provided for securing bolts during reassembly.
Caterpillar Cat 312C L Excavator (Prefix BWH) Service Repair Manual (BWH00001...fusjekkdmdmd2w
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and seal installation using a installer tool.
- Flywheel housing removal by lifting it off with straps after removing bolts, and installation by cleaning the mating surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and installing by securing with a washer and nut.
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and seal installation using a installer tool.
- Flywheel housing removal by lifting it off with straps and removing bolts, and installation by cleaning the mating surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and installing by securing with a washer and nut.
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. The installation procedure specifies cleaning the crankshaft and pulley, applying retaining compound, and pressing the pulley onto the crankshaft with an installer tool. Torque specifications are provided for securing bolts during reinstallation.
Caterpillar Cat 312C L Excavator (Prefix BWH) Service Repair Manual (BWH00001...f8usejkddmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and installation using a installer tool and retaining compound.
- Flywheel housing removal by lifting it off with straps after removing bolts, and installation by cleaning surfaces and securing with new bolts.
- Crankshaft pulley removal using a puller and chisel if needed, and installation by positioning it and tightening the nut to the specified torque.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...idkkdmmd
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. The installation procedure specifies cleaning the crankshaft and pulley, applying retaining compound, and pressing the pulley onto the crankshaft with an installer tool. Torque specifications are provided for securing bolts during reinstallation.
Caterpillar Cat 312C L Excavator (Prefix BWH) Service Repair Manual (BWH00001...8ufjsekddm8u
The document provides instructions for removing and installing various engine components on a Caterpillar 3064 engine, including:
- Flywheel installation which requires pressing the ring gear onto the flywheel and securing it with bolts.
- Crankshaft rear seal removal using a slide hammer puller and distorter tool, and seal installation using a installer tool.
- Flywheel housing removal by lifting it off with straps after removing bolts, and installation by cleaning the mating surfaces and securing with bolts.
- Crankshaft pulley removal using a puller and chisel if needed, and installation by positioning it and securing with a washer and nut.
Similar to Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual Instant Download.pdf (8)
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336F and 336F L Excavator (Prefix DSW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 345D L Excavator (Prefix JKN) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, bearings and other components into the travel motor housing and barrel. Measurements are taken throughout to ensure proper assembly. The travel motor is then installed on the excavator and filled with the correct oil type.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar Cat 336E L Excavator (Prefix BZY) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstalling parts. Special care must be taken when handling springs or parts under spring force to avoid injury.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It describes 37 steps to disassemble the final drive by removing gears, shafts, housings, seals and other components. It then describes 34 steps to reassemble the final drive, including pressing in new bearings, installing seals, adjusting bearing preload with shims, and applying threadlocker to bolts. Precise tools and lifting devices are required due to the heavy weights of up to 550 kg involved.
Caterpillar Cat 336E L Excavator (Prefix DPX) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor on a 336E L excavator. The disassembly process involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and ensuring proper alignment of components.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fskekkdmdmdm3e
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It describes removing over 30 components of the travel motor including the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates and more.
3) Detailed illustrations are provided to accompany each step showing how to remove each component using the recommended tools.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, in reverse order, including attaching lifting devices, positioning the assembly, and reinstalling hoses and covers. Tools and torque specifications are provided.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLC) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for removing and installing a crankshaft wear sleeve and crankshaft gear on a 325C excavator. It describes using various tools to distort and remove the existing wear sleeve and instructions for installing a new sleeve using a multi-piece installer tool. It also outlines steps for removing the crankshaft gear using a bearing puller and installing the gear by heating it and pressing it onto the crankshaft. The document provides maintenance technicians with detailed parts and tool information as well as safety notices for completing these tasks.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required include drivers, link brackets, guide studs, and installation tools.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306B engine. It describes:
1) Marking the gears to ensure proper timing during removal and installation.
2) Removing the camshaft bolts and carefully removing the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before installation.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
The document provides instructions for removing and installing various components of a Caterpillar 621E wheel scraper, including:
1) Removing and installing the push-pull plate that connects the push-pull spring to the support assembly.
2) Disassembling and assembling the push-pull spring itself by removing discs and plates.
3) A detailed process for removing and installing the ejector cylinder, which requires the use of lifting tools and wood blocks due to the cylinder's weight.
4) Brief instructions for removing and adjusting the position of the lower front and guide rollers on the ejector assembly.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C L EXCAVATOR CBA
Configuration: 312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 23:15:35 UTC+0800 2020
3/3
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C L EXCAVATOR CBA
Configuration: 312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 23:16:34 UTC+0800 2020
3/3
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C L EXCAVATOR CBA
Configuration: 312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 23:17:33 UTC+0800 2020
4/4
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C L EXCAVATOR CBA
Configuration: 312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 23:18:32 UTC+0800 2020
2/2
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C L EXCAVATOR CBA
Configuration: 312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 23:19:32 UTC+0800 2020
2/2
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C L EXCAVATOR CBA
Configuration: 312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g00611569
3. Remove idler gear (3) from the idler gear shaft.
Illustration 3 g00611570
4. If necessary, use Tool (B) to remove bushing (4) (not shown) from idler gear (3) .
Illustration 4 g00611572
3/5
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 5 g00611573
5. The following items are components of Tool (A) .
◦ 9U-6147 Stud (6)
◦ 6V-8231 Nut (7)
◦ 9U-6146 Sleeve Assembly (8)
◦ 8T-4244 Nut (9)
6. Use Tool (A) and remove idler shaft (5) from the cylinder block. Check the idler shaft for
wear and damage. Replace the shaft, if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
• In order to remove the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Remove".
• In order to remove the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel
Injection Pump - Remove".
• In order to remove the gear from the engine oil pump, refer to Disassembly and Assembly,
"Engine Oil Pump - Remove".
• In order to remove the crankshaft gear, refer to Disassembly and Assembly, "Crankshaft
Gear - Remove and Install".
4/5
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C L EXCAVATOR CBA
Configuration: 312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615420
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g00611570
1. Use Tool (A) to install a new bushing (4) (not shown), if the bushing was removed.
Illustration 2 g00611572
2. Install idler shaft (5) onto the cylinder block.
Note: When the idler shaft is installed, ensure that the oil hole of the shaft is up. If
necessary, cool the idler shaft to 0 °C (32 °F) before installation. The temperature of the
idler shaft is lowered in order to ease the installation of the idler shaft.
Illustration 3 g00611569
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection
drive gear with the "33" mark with the "3" mark on idler gear. Make an alignment of the "2"
mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the
crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center
position when these marks are in alignment.
3. Install idler gear (3) onto the idler shaft.
2/3
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 4 g00611568
4. Install thrust plate (2) onto the idler shaft.
5. Install the washer and idler gear bolt (1) onto thrust plate (2). Tighten idler gear bolt (1) to a
torque of 34 ± 5 N·m (25 ± 4 lb ft).
Note: For more information, refer to Specifications, "Gear Group (Front)".
Note: See the following list for the installation of the other gears in the front gear group.
• In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Install".
• In order to install the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel
Injection Pump - Install".
• In order to install the gear from the engine oil pump, refer to Disassembly and Assembly,
"Engine Oil Pump - Install".
• In order to install the crankshaft front gear, refer to Disassembly and Assembly, "Crankshaft
Gear - Remove and Install".
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 23:21:30 UTC+0800 2020
3/3
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C L EXCAVATOR CBA
Configuration: 312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615434
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
A. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
B. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
C. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
D. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/4
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00605981
1. Loosen hose clamp (1) that secures hose (2) to the front housing.
2. Disconnect hose (2) from the front housing.
Illustration 2 g00605985
2/4
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. 3. Remove bolts (3) and the washers that hold front housing (4) to the plate and the cylinder
block.
4. Remove six bolts (5) (not shown) and the washers that mount the front housing (4) to the oil
pan.
Illustration 3 g00606002
5. Remove two bolts (6) and the washers that mount the front housing (4) to the front plate (8)
and the cylinder block.
6. Use two technicians to remove the front housing from the cylinder block and the front plate.
The weight of the front housing is 20 kg (45 lb).
Note: Check the condition of the gasket (7) (not shown) for the engine oil pan. If the gasket
is damaged, it may be necessary to replace the gasket. Refer to Disassembly and Assembly,
"Engine Oil Pan - Remove and Install" for replacement of the gasket for the engine oil pan.
3/4
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...