The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on the shaft.
3) Checking gear backlash and end play measurements during installation.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...soeldksejdksem
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing a new bushing if needed and lowering the idler shaft temperature before installing the shaft, idler gear, thrust plate, washer and bolt.
3) Checking backlash and end play measurements during installation.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix nc5) service rep...cdfzxs
The document provides instructions for removing and installing various engine components of a 305.5E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including the inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil pump, water pump, and water temperature regulator. The procedures include draining fluids, removing fasteners and hoses, cleaning parts, and installing components in reverse order of removal while following safety notices.
The document provides instructions for removing and installing a cylinder head on a 3054C engine. Key steps include:
1. Draining fluids, removing related components like the exhaust manifold and fuel injectors before removing the cylinder head.
2. Gradually loosening and removing cylinder head bolts in reverse order to prevent distortion, then lifting off the head using a lifting device.
3. Cleaning the cylinder block and head mating surfaces, installing a new gasket and dowel pins before positioning the head back on using guide bolts for alignment.
4. Reinstalling the bolts and tightening them in stages to the specified torque in numerical order.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...soeldksejdksem
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing a new bushing if needed and lowering the idler shaft temperature before installing the shaft, idler gear, thrust plate, washer and bolt.
3) Checking backlash and end play measurements during installation.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix nc5) service rep...cdfzxs
The document provides instructions for removing and installing various engine components of a 305.5E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including the inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil pump, water pump, and water temperature regulator. The procedures include draining fluids, removing fasteners and hoses, cleaning parts, and installing components in reverse order of removal while following safety notices.
The document provides instructions for removing and installing a cylinder head on a 3054C engine. Key steps include:
1. Draining fluids, removing related components like the exhaust manifold and fuel injectors before removing the cylinder head.
2. Gradually loosening and removing cylinder head bolts in reverse order to prevent distortion, then lifting off the head using a lifting device.
3. Cleaning the cylinder block and head mating surfaces, installing a new gasket and dowel pins before positioning the head back on using guide bolts for alignment.
4. Reinstalling the bolts and tightening them in stages to the specified torque in numerical order.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskekdmmem
This document provides instructions for removing and installing the idler gear on the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate, and bushing. The installation procedure specifies cleaning and inspecting parts, pressing in a new bushing if needed, installing the idler gear and shaft, checking backlash and end play, and aligning timing gear marks.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...fksjksmmde
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Installing involves pressing in a new idler gear bushing if needed, lowering the idler shaft temperature, and installing the idler gear, thrust plate, washer and bolt while checking backlash and end play
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...tuzhiyou2
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...qfyc504378
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar C4.2 engine.
The idler gear removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The idler gear installation is the reverse of removal. Tolerances and specifications for components are provided.
The front housing removal requires removing several other components first, then removing bolts and separating the housing. Installation involves reversing the removal steps and checking gaskets and seals.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal procedure for the front housing includes removing components attached to the housing like the alternator and fuel injection pump. It also provides instructions for removing housing mounting bolts and removing the front housing from the engine.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...lituo39419496
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
Caterpillar cat 314 d cr excavator (prefix pdp) service repair manual (pdp000...fhsjejkdmem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...fhsejkdkmem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...fhsjekkdkem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d cr excavator (prefix pdp) service repair manual (pdp000...fjjsekdmme
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar Cat 314D CR and 314D LCR Excavator (Prefix PDP) Service Repair Ma...fijsekkdmdm2w
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. The removal procedure includes using various tools to remove the idler gear, idler shaft, and front housing. The installation procedure outlines installing the idler gear, checking gear backlash and end play, and installing the front housing.
Caterpillar Cat 314D CR and 314D LCR Excavator (Prefix PDP) Service Repair Ma...zan2736ban
The document provides instructions for removing and installing an idler gear on the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt and washer, thrust plate, and idler gear. It notes to check the idler shaft for wear and replace if needed. Instructions are also provided for installing the idler gear, including measuring backlash and end play.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...fjskekxcddmmme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarification. The goal is to fully disassemble the travel motor into its individual parts for repair or replacement.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in tables throughout.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive of a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...fjskekxcddmmme
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools. Cleanliness is emphasized throughout.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 24 steps to remove components like the head assembly, brake housing, barrel assembly, pistons, and bearings. The assembly process reverses this with 13 steps like installing seals, springs, pins and bearings onto components before lowering the rotating group into the motor housing. Precautions and torque specifications are provided for correct reassembly.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
More Related Content
Similar to Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 and up)
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskekdmmem
This document provides instructions for removing and installing the idler gear on the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate, and bushing. The installation procedure specifies cleaning and inspecting parts, pressing in a new bushing if needed, installing the idler gear and shaft, checking backlash and end play, and aligning timing gear marks.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...fksjksmmde
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Installing involves pressing in a new idler gear bushing if needed, lowering the idler shaft temperature, and installing the idler gear, thrust plate, washer and bolt while checking backlash and end play
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...tuzhiyou2
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...qfyc504378
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar C4.2 engine.
The idler gear removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The idler gear installation is the reverse of removal. Tolerances and specifications for components are provided.
The front housing removal requires removing several other components first, then removing bolts and separating the housing. Installation involves reversing the removal steps and checking gaskets and seals.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal procedure for the front housing includes removing components attached to the housing like the alternator and fuel injection pump. It also provides instructions for removing housing mounting bolts and removing the front housing from the engine.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...lituo39419496
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
Caterpillar cat 314 d cr excavator (prefix pdp) service repair manual (pdp000...fhsjejkdmem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...fhsejkdkmem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...fhsjekkdkem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d cr excavator (prefix pdp) service repair manual (pdp000...fjjsekdmme
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar Cat 314D CR and 314D LCR Excavator (Prefix PDP) Service Repair Ma...fijsekkdmdm2w
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. The removal procedure includes using various tools to remove the idler gear, idler shaft, and front housing. The installation procedure outlines installing the idler gear, checking gear backlash and end play, and installing the front housing.
Caterpillar Cat 314D CR and 314D LCR Excavator (Prefix PDP) Service Repair Ma...zan2736ban
The document provides instructions for removing and installing an idler gear on the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt and washer, thrust plate, and idler gear. It notes to check the idler shaft for wear and replace if needed. Instructions are also provided for installing the idler gear, including measuring backlash and end play.
Similar to Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 and up) (14)
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...fjskekxcddmmme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarification. The goal is to fully disassemble the travel motor into its individual parts for repair or replacement.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in tables throughout.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive of a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...fjskekxcddmmme
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools. Cleanliness is emphasized throughout.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 24 steps to remove components like the head assembly, brake housing, barrel assembly, pistons, and bearings. The assembly process reverses this with 13 steps like installing seals, springs, pins and bearings onto components before lowering the rotating group into the motor housing. Precautions and torque specifications are provided for correct reassembly.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...fjskekxcddmmme
This document provides disassembly and assembly instructions for the final drive of a 349E L excavator. It includes specifications for the components, required tools, assembly procedures with illustrations, and torque specifications. The procedures describe cleaning and applying lubricants to parts, measuring clearances, installing bearings and seals, and adjusting shims to set proper spacing before tightening bolts and setscrews to specified torques.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...fjskekxcddmmme
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts and lubricant is used where appropriate.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section lists 14 steps and specifies torque values and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in supporting tables throughout.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive on a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque specifications are provided for reinstallation.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 d2 l vg excavator (prefix sdm) service repair manual (sdm...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 30 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 31 steps for assembly, reinstalling these components in reverse order. Precautions are given to prevent contamination and ensure proper installation of parts like O-rings, seals, and pins in their original locations. Tools required are listed in a table.
Caterpillar cat 349 d2 l vg excavator (prefix pfd) service repair manual (pfd...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 27 steps for assembly, installing components like seals, pistons, housing, plates and head in reverse order of disassembly. Tools required are listed in tables. Cautions are provided regarding cleaning, marking parts, and applying lubricant before assembly.
Caterpillar cat 349 d2 l excavator (prefix zae) service repair manual (zae000...fjskekxcddmmme
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal of a C13 engine. It outlines 11 steps to remove the rear gear group involving removing bolts, gears, seals, and bearings. It then outlines 12 steps to install the rear gear group in reverse order, noting specific tools and torque specifications. Separate sections provide 2 step instructions each for removing the flywheel and installing the crankshaft rear seal.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01374810
Illustration 6 g01374811
5. The following items are components of Tooling (A).
◦ 9U-6147 Stud (9)
◦ 6V-8231 Nut (10)
◦ 9U-6146 Sleeve Assembly (11)
◦ 8T-4244 Nut (12)
6. Use Tooling (A) in order to remove idler shaft (8) (not shown) from the cylinder block.
Check idler shaft (8) for wear and damage. Replace idler shaft (8), if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
◦ In order to remove camshaft gear (3), refer to Disassembly and Assembly, "Camshaft
- Remove".
◦ In order to remove fuel injection pump gear (1), refer to Disassembly and Assembly,
"Fuel Injection Pump - Remove".
◦ In order to remove the gear from the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Remove".
◦ In order to remove crankshaft gear (4), refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:32:55 UTC+0800 2020
4/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879402
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
a 1p-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01374804
1. Use Tooling (A) and a suitable press in order to install a new bushing (7) (not shown), if the
bushing was removed.
Illustration 2 g01374810
2. Lower the temperature of idler shaft (8) . Install idler shaft (8) (not shown) onto the cylinder
block.
Note: When idler shaft (8) is installed, ensure that the oil hole of idler shaft (8) is up.
Illustration 3 g01374827
3. Install idler gear (2) onto idler shaft (8) .
2/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
Illustration 5 g01374789
4. Install thrust plate (6) onto the idler shaft.
5. Install the washer and idler gear bolt (5) onto thrust plate (6) . Tighten idler gear bolt (5) to a
torque of 34 ± 5 N·m (25 ± 4 lb ft).
3/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: See the following list for the installation of the other gears in the front gear group.
◦ In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Install".
◦ In order to install the fuel injection pump gear, refer to Disassembly and Assembly,
"Fuel Injection Pump - Install".
◦ In order to install the gear to the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Install".
◦ In order to install the crankshaft front gear, refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Illustration 6 g01374841
6. Install a dial indicator and rotate idler gear (2) back and forth in order to measure backlash.
Refer to Table 3.
Table 2
Item Standard at Assembly Service Limit
Backlash of crankshaft gear and
idler gear
0.510 to 0.157 mm (0.0201 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of camshaft gear and
idler gear
0.520 to 0.158 mm (0.0205 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of fuel injection pump
gear and idler gear
0.0560 to 0.205 mm (0.0022 to
0.0081 inch)
0.250 mm (0.0098
inch)
4/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. End play of idler gear
0.050 to 0.200 mm (0.0020 to
0.0079 inch)
0.350 mm (0.0138
inch)
Clearance between idler gear
bushing and shaft
0.009 to 0.050 mm (0.0004 to
0.0020 inch)
0.100 mm (0.0039
inch)
Illustration 7 g01374874
7. Measure the end play of idler gear (2) with a feeler gauge. Refer to Table 3.
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:33:54 UTC+0800 2020
5/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02743335
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
c. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
d. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374908
1. Loosen hose clamp (1) that secures hose (2) to the front housing.
2. Disconnect hose (2) from the front housing.
Illustration 2 g00605985
3. Remove bolts (3) and the washers that hold front housing (4) to the plate and the cylinder
block.
2/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 4. Remove six bolts (5) (not shown) and the washers that mount front housing (4) to the oil
pan.
Illustration 3 g00606002
5. Remove bolts (6) and the washers that mount front housing (4) to front plate (8) and the
cylinder block.
6. Use two people in order to remove front housing (4) from the cylinder block and front plate
(8). The weight of front housing (4) is approximately 20 kg (45 lb).
Note: Check the condition of gasket (7) (not shown) for the engine oil pan. If gasket (7) is
damaged, it may be necessary to replace gasket (7). Refer to Disassembly and Assembly,
"Engine Oil Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
3/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g01377884
7. Remove baffle plate (9).
Illustration 5 g01377894
8. Use Tooling (A) in order to remove crankshaft front seal (10) (not shown) from front
housing (4), if necessary.
9. Check the teeth of the timing gears for the following items: wear, nicks, chips and uneven
contact. Check the keyway for wear or damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:34:53 UTC+0800 2020
4/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879387
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets, and the seals for wear or for damage. Replace the components, if
necessary.
1/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00836619
Alignment marks for timing gears
1. Check the alignment of the timing gears.
Note: Ensure that the marks on the timing gears are in alignment. Align the "3" mark on the
fuel injection pump drive gear with the "33" mark on the idler gear. Make an alignment of
the "2" mark on the idler gear with the "22" mark on the camshaft gear. Align the "1" mark
on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top
center position when the timing marks are in alignment.
Illustration 2 g00606022
2. Ensure that the old gasket material (9) is removed from the mating surface of front housing
(4) and the timing gear plate. Install a new gasket (9) .
3. If the crankshaft front seal (10) (not shown) was removed, use Tooling (A) in order to
install a new crankshaft front seal (10) .
2/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00606002
4. Before installation of front housing (4) , check gasket (7) (not shown) for the oil pan for
damage. Replace gasket (7) , if necessary. Refer to Disassembly and Assembly, "Engine Oil
Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
5. Use two people in order to install front housing (4) onto front plate (8) and the cylinder
block. The weight of front housing (4) is approximately 20 kg (45 lb).
6. Install bolts (6) in order to fasten front housing (4) onto the cylinder block and front plate
(8) .
Illustration 4 g00605985
7. Install the washers and six bolts (5) (not shown) in order to secure front housing (4) onto
engine oil pan.
3/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install bolts (3) and washers that secure front housing (4) to the front plate and the cylinder
block.
Illustration 5 g01374908
9. Connect hose (2) to the front housing.
10. Tighten hose clamp (1) in order to secure hose (2) to the front housing.
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
c. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
d. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:35:52 UTC+0800 2020
4/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i01615486
Front Plate - Remove
SMCS - 1163-011
Removal Procedure
Start By:
a. Remove the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove".
b. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
c. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00611711
1. Remove one bolt (1) and the washer from the front plate (2).
2. Remove front plate (2) from the engine.
3. Remove gasket (3) (not shown) from the engine or from the front plate (2).
Note: Ensure that all mating surfaces are clear of old gaskets.
Note: Check the cylinder block for the following conditions: scale buildup, corrosion and
other damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:36:52 UTC+0800 2020
2/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i01576831
Front Plate - Install
SMCS - 1163-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611711
1. Place gasket (3) (not shown) in position on the engine.
Note: Ensure that all mating surfaces are clear of old gaskets.
2. Place front plate (2) in position on the engine.
1/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 3. Install one bolt (1) and the washer in order to secure front plate (2) to the engine. Tighten
the bolt to a torque of 35 ± 5 N·m (26 ± 4 lb ft).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
c. Install the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:37:51 UTC+0800 2020
2/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879389
Crankcase Breather - Remove and Install
SMCS - 1317-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01374569
1. Loosen clamps (3) and remove hose (2) .
2. Remove breather assembly (1) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01374569
1. Install new breather assembly (1) .
2. Install hose (2) and tighten hose clamps (3) .
Wed May 27 08:38:50 UTC+0800 2020
2/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768517
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01384853
1. Remove bolts (1) and remove cover (2) .
1/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 2 g01385013
2. Disconnect hose (3) .
3. Remove bolts (4) and remove valve mechanism cover (5) and the O-ring seal.
Installation Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01385013
1. Position valve mechanism cover (5) and the O-ring seal. Install bolts (4). Tighten bolts (4)
to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
2/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 2. Connect hose (3) .
Illustration 4 g01384853
3. Position cover (2) and install bolts (1). Tighten bolts (1) to a torque of 17 ± 2 N·m (13 ± 1 lb
ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:39:50 UTC+0800 2020
3/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...