The document provides instructions for removing and installing a fuel injection pump and turbocharger on a Caterpillar 3064 engine. The procedures include removing fuel lines and bolts to remove the components, cleaning surfaces, installing new gaskets, and torquing bolts to specifications for reinstallation. Tools and safety precautions are also listed.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjskkksmemm
This document is an operation and maintenance manual for a Doosan DL420 wheel loader. It provides information on the intended use of the machine, its components like the engine, transmission, braking and hydraulic systems. It also describes the cabin, FOPS and ROPS safety structures. The manual discusses CE marking requirements and installing communication equipment safely. Product plates for identifying the machine and components are shown.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 3064 or 3066 engine. It includes illustrations and steps to remove the threaded plug and shim that contain the valve from the cylinder block. Proper cleaning and containment of fluids is emphasized. The summary is completed in 3 sentences or less.
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
This document provides instructions for installing the automatic timing advance on a 3306 engine. It describes:
1. Installing a fuel pump timing pin and bolt to hold the camshaft in position.
2. Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3. Removing the tools and installing the front housing once the timing advance is installed.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 312 b excavator (prefix 6sw) service repair manual (6sw00001 ...fjsekksmemm
This document provides instructions for removing and installing the camshaft and camshaft gear on a 3054 engine. It describes:
1) Removing the rocker shaft, pushrods, fuel transfer pump, and front housing before removing the camshaft.
2) Using a puller tool to remove the camshaft gear after aligning timing marks.
3) Lubricating and carefully installing the camshaft, making sure not to damage lobes or bearings.
4) Cleaning and aligning the camshaft bearings before pressing them into place.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjskkksmemm
This document is an operation and maintenance manual for a Doosan DL420 wheel loader. It provides information on the intended use of the machine, its components like the engine, transmission, braking and hydraulic systems. It also describes the cabin, FOPS and ROPS safety structures. The manual discusses CE marking requirements and installing communication equipment safely. Product plates for identifying the machine and components are shown.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 3064 or 3066 engine. It includes illustrations and steps to remove the threaded plug and shim that contain the valve from the cylinder block. Proper cleaning and containment of fluids is emphasized. The summary is completed in 3 sentences or less.
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
This document provides instructions for installing the automatic timing advance on a 3306 engine. It describes:
1. Installing a fuel pump timing pin and bolt to hold the camshaft in position.
2. Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3. Removing the tools and installing the front housing once the timing advance is installed.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 312 b excavator (prefix 6sw) service repair manual (6sw00001 ...fjsekksmemm
This document provides instructions for removing and installing the camshaft and camshaft gear on a 3054 engine. It describes:
1) Removing the rocker shaft, pushrods, fuel transfer pump, and front housing before removing the camshaft.
2) Using a puller tool to remove the camshaft gear after aligning timing marks.
3) Lubricating and carefully installing the camshaft, making sure not to damage lobes or bearings.
4) Cleaning and aligning the camshaft bearings before pressing them into place.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the heavy fuel injection pump from the engine.
3. Removing hoses and bolts to detach the turbocharger, oil lines, and exhaust manifold as a single unit from the engine.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil lines from the turbocharger.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...tuzhiyou2
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...qfyc504378
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...lituo39419496
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the fuel injection pump from the engine block.
3. Removing hoses and lines connected to the turbocharger, then removing nuts to separate the turbocharger from the exhaust manifold.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil supply and return lines.
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...zan2736ban
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Cleaning the crankshaft and applying retaining compound to the mating surfaces.
2) Using a installer tool to push the new seal onto the crankshaft until it bottoms out.
3) Removing the tool and checking that the seal is correctly installed.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...fusjekkdmdmd2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve if needed.
- Removing the crankshaft front seal by drilling holes and pulling it off with a slide hammer puller.
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Drilling three holes in the old seal and using a slide hammer puller to remove it, being careful not to damage the crankshaft flange.
2) Cleaning the crankshaft flange surface and applying a sealing compound.
3) Using an installer tool to push the new seal into place until it is fully seated on the crankshaft flange.
The summary covers the key steps for removing the old seal and installing the new one in 3 sentences while maintaining the essential details.
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...f8usejkddmmd
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Drilling three holes in the old seal and using a slide hammer puller to remove it, being careful not to damage the crankshaft flange.
2) Cleaning the crankshaft flange surface and applying a retaining compound.
3) Using an installer tool to push the new seal into place until it is fully seated on the crankshaft flange.
The summary covers the key steps for removing the old seal and installing the new one in 3 sentences while maintaining the essential details.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...8ufjsekddm8u
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Kubota m5500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part listings for a parts book. It defines the column headings used on part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country. The summary lists the main document sections and provides an example part listing for a crankcase.
Kubota m5040 hdc tractor parts catalogue manualdfjjsjkemmm
The document provides parts information for an engine, including:
- Descriptions of column headings for part number pages like part number, name, quantity, etc.
- Parts lists organized by component (e.g. crankcase, oil pan, cylinder head) with part numbers, names, quantities, and other details.
- Notes on country codes used for parts that may differ between countries.
Kubota l4610 dt hst tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a crankcase, including the crankcase itself along with various plugs, caps, pins, and other component parts. Key information includes the part number, description, quantity used, applicable serial number range, interchangeability, and remarks.
Kubota l4400 h tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages, including reference number, part number, part name, quantity, serial number range, and remarks. It notes country codes that may be included and what they indicate. Sample pages from the parts book are then provided that list part numbers, descriptions, quantities and other details for specific assembly items like the crankcase, oil pan, cylinder head, gear case and more.
Kubota l4310 dt gst-chst-c tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and definitions for parts books. It explains that the parts book headings will match the picture pages. It defines the column headings for part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country.
Kubota l3410 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3300 dt gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for parts books. It explains the column headings used on parts pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included to indicate part differences between countries. The document then provides an example page from a parts book listing parts for an engine crankcase.
More Related Content
Similar to Caterpillar cat 312 c excavator (prefix dbn) service repair manual (dbn00001 and up)
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the heavy fuel injection pump from the engine.
3. Removing hoses and bolts to detach the turbocharger, oil lines, and exhaust manifold as a single unit from the engine.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil lines from the turbocharger.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...tuzhiyou2
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...qfyc504378
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...lituo39419496
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the fuel injection pump from the engine block.
3. Removing hoses and lines connected to the turbocharger, then removing nuts to separate the turbocharger from the exhaust manifold.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil supply and return lines.
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...zan2736ban
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Cleaning the crankshaft and applying retaining compound to the mating surfaces.
2) Using a installer tool to push the new seal onto the crankshaft until it bottoms out.
3) Removing the tool and checking that the seal is correctly installed.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...fusjekkdmdmd2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve if needed.
- Removing the crankshaft front seal by drilling holes and pulling it off with a slide hammer puller.
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Drilling three holes in the old seal and using a slide hammer puller to remove it, being careful not to damage the crankshaft flange.
2) Cleaning the crankshaft flange surface and applying a sealing compound.
3) Using an installer tool to push the new seal into place until it is fully seated on the crankshaft flange.
The summary covers the key steps for removing the old seal and installing the new one in 3 sentences while maintaining the essential details.
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...f8usejkddmmd
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Drilling three holes in the old seal and using a slide hammer puller to remove it, being careful not to damage the crankshaft flange.
2) Cleaning the crankshaft flange surface and applying a retaining compound.
3) Using an installer tool to push the new seal into place until it is fully seated on the crankshaft flange.
The summary covers the key steps for removing the old seal and installing the new one in 3 sentences while maintaining the essential details.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...8ufjsekddm8u
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Similar to Caterpillar cat 312 c excavator (prefix dbn) service repair manual (dbn00001 and up) (13)
Kubota m5500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part listings for a parts book. It defines the column headings used on part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country. The summary lists the main document sections and provides an example part listing for a crankcase.
Kubota m5040 hdc tractor parts catalogue manualdfjjsjkemmm
The document provides parts information for an engine, including:
- Descriptions of column headings for part number pages like part number, name, quantity, etc.
- Parts lists organized by component (e.g. crankcase, oil pan, cylinder head) with part numbers, names, quantities, and other details.
- Notes on country codes used for parts that may differ between countries.
Kubota l4610 dt hst tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a crankcase, including the crankcase itself along with various plugs, caps, pins, and other component parts. Key information includes the part number, description, quantity used, applicable serial number range, interchangeability, and remarks.
Kubota l4400 h tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages, including reference number, part number, part name, quantity, serial number range, and remarks. It notes country codes that may be included and what they indicate. Sample pages from the parts book are then provided that list part numbers, descriptions, quantities and other details for specific assembly items like the crankcase, oil pan, cylinder head, gear case and more.
Kubota l4310 dt gst-chst-c tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and definitions for parts books. It explains that the parts book headings will match the picture pages. It defines the column headings for part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country.
Kubota l3410 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3300 dt gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for parts books. It explains the column headings used on parts pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included to indicate part differences between countries. The document then provides an example page from a parts book listing parts for an engine crankcase.
Kubota l3130 hst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l3130 gst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as Reference Number, Part Number, Description, Quantity, Serial Number range, Interchangeability, and Remarks. It also notes country codes that may be included, such as exceptions for parts in other countries like France (FR). Diagrams of product parts are indexed for locating specific components.
Kubota l3130 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l2900 f tractor parts catalogue manualdfjjsjkemmm
This document provides an index and part listings for an L2900F product. It includes sections for the engine, fuel system, cooling water system, electrical system, clutch, transmission, rear axle, brake, front axle, steering, hydraulic system, hood, labels, and accessories. Each section lists the relevant part numbers, descriptions, quantities, and other specifications for the individual components.
Kubota l2900 dt tractor parts catalogue manualdfjjsjkemmm
The crankcase parts list includes over 230 individual parts that make up the crankcase assembly. It lists each part number, description, quantity used, applicable serial number range, interchangeability, remarks, and weight. Key details included are the total weight of the assembled crankcase (48.5kg/106.7lbs) and that most common individual parts like plugs and seals weigh only a few grams.
Kubota l2800 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using a parts book for a tractor model. It defines the column headings used on parts number pages, including the part reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate if a part is different for other countries. The document then provides an index of parts for the tractor model with the part number and relevant parts book for each item.
Kubota l2800 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using parts books and describes the column headings used on parts number pages. It explains that country codes may be included to indicate if a part is different for other countries. Finally, it lists frequently used parts for a L2800DT/HST tractor, including the part number, description, and reference book for each part.
Kubota l2600 dt tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a cylinder head. It includes a list of 170 parts with information on the part number, description, quantity used, applicable serial number range, interchangeability, and remarks. It notes country codes that may be relevant for part interchangeability between countries like the US, Canada, France, etc. The total weight of the cylinder head component is provided at the end.
Kubota l2500 f tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It lists the column headings used on parts pages including the reference number, part number, description, quantity, serial number range and other details. It then provides an example page from the parts book with over 250 individual part numbers listed for the crankcase component.
Kubota l2500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books. It defines the column headings used on parts number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes are also explained, with symbols indicating the country each part is for (e.g. A for USA, CA for Canada, FR for France). An example page from a parts book is then shown listing parts for an engine crankcase, with the corresponding information for each part.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565175
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the engine is the top center position on number one piston. Refer to Testing and
Adjusting, "Finding Center Position for No. 1 Piston".
Illustration 1 g00813442
2. Remove bolts (1) and washers that secure the cover (2) to the engine front housing.
3. Remove the access cover. Note the timing marks on the fuel injection pump drive gear and
the idler gear for later installation.
Illustration 2 g00813430
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Scribe a line across the front plate (3) and the mounting flange for the fuel injection pump
(4). This ensures proper alignment for the installation of fuel injection pump (8) .
5. Loosen fitting (5) for oil line (6) .
6. Remove oil line (6) from nipple (7) (not shown).
Note: Put caps or plugs on all openings immediately in order to prevent contamination.
7. Use a lifting sling and a hoist in order to secure the fuel injection pump. The weight of the
fuel injection pump is 13 kg (29 lb).
Note: Use Tool (B) to remove the bolts and the washers that mount the fuel injection pump
(8) .
8. Remove bolt (9) and the washer from the cylinder block.
9. Remove four bolts (10) and the washers that secure the fuel injection pump to the front
housing.
Illustration 3 g00813593
10. Remove the fuel injection pump (8). The gear and the mounting flange will remain with the
fuel injection pump.
Note: The fuel injection pump must be mounted to the engine in order to loosen the nut for
the drive gear.
Note: Do not rotate the engine after the fuel injection pump is removed.
11. Ensure that the old gasket material is removed from all mating surfaces of the pump
mounting flange and the face of the fuel injection pump flange.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:14:12 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565619
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: If the nut for the fuel injection pump drive gear is removed, you must tighten the nut
for the fuel injection pump drive gear to 88 ± 5 N·m (65 ± 4 lb ft).
1/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00813430
1. Use a lifting sling and a hoist in order to secure the fuel injection pump (8). The weight of
the fuel injection pump is 13 kg (29 lb).
2. Install a new gasket and install fuel injection pump (8) .
3. Ensure that the engine is in the top center position on No. 1 piston. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
4. Ensure that the mark on the front plate (3) and the mark on the fuel injection pump flange
(4) are aligned.
Refer to Testing and Adjusting, "Fuel Injection Timing-Check" for more information on
fuel injection pump timing.
Note: Use Tool (B) to install the bolts and washers that secure the fuel injection pump to the
cylinder block.
5. Install the washers and bolts (9) that secure the fuel injection pump to the engine cylinder
block.
6. Remove the sling from the fuel injection pump.
7. Connect oil line (6) to nipple (7) (not shown).
8. Tighten fitting (5) for oil line (6) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:15:12 UTC+0800 2020
2/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564499
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00608136
1. Loosen the hose clamp (1) on hose (2) .
2. Remove hose (2) from the turbocharger (3) .
Illustration 2 g00812846
3. Disconnect oil supply line (4) from the cylinder block.
4. Loosen two clamps (5) on hose (7) .
5. Slide hose (7) off fitting (8) onto oil return line (6) .
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00608177
6. Remove eight nuts (9) from the studs on the exhaust manifold.
Note: The four studs have two nuts for a total of eight nuts.
7. Remove turbocharger (3), oil supply line (4), and oil return line (6) as an unit.
8. Remove metal gasket (10) (not shown). Check the gasket for wear or damage. Replace the
gasket, if necessary.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:16:11 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615171
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/4
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 1. Place an index mark on all of the components. The marks will help to align the components
during the assembly procedure.
Illustration 1 g00608212
2. Remove two bolts (1) from the oil return line. Remove bolt (2) from the oil supply line.
3. Remove oil return line (3) from the cartridge.
4. Remove oil supply line (4) from the cartridge.
Illustration 2 g00608210
5. Remove gasket (5) from the cartridge.
6. Remove gasket (6) from the turbine housing.
2/4
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00608342
7. Remove the bolt and nut (7) from clamp (8). Remove clamp (8) that secures the turbine
housing (9) to the cartridge (10) .
8. Separate turbine housing (9) from the cartridge (10) .
Illustration 4 g00608415
Illustration 5 g00608452
3/4
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 9. Remove snap ring (11) from compressor housing (12) .
10. Separate compressor housing (12) from the cartridge (10) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:17:10 UTC+0800 2020
4/4
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01147762
Turbocharger - Assemble
SMCS - 1052-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: During the assembly procedure, ensure that the index marks are aligned when the
components are assembled.
Illustration 1 g00608452
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g00608415
1. Install cartridge (10) into compressor housing (12) .
2. Install snap ring (11) into compressor housing (12) .
Illustration 3 g00608342
3. Install cartridge (10) into turbine housing (9) .
4. Install clamp (8) that secures cartridge (10) and turbine housing (9) together. Install the bolt
and nut (7) into clamp (8).
Note: Refer to the Specifications Module, "Turbocharger" for information on the clamp.
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g00608210
5. Inspect the condition of the gaskets. Replace the gaskets, if necessary.
6. Install gasket (6) on the turbine housing.
7. Install gasket (5) on the cartridge.
Illustration 5 g00608212
8. Place oil supply line (4) in position. Secure the oil supply line with bolt (2) (not shown).
9. Place oil return line (3) in position. Secure the oil return line with two bolts (1) .
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:18:09 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564587
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the condition of all gaskets. Replace the gaskets, if necessary.
Illustration 1 g00608177
1/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 2. Install metal gasket (10) (not shown). Install turbocharger (3), oil supply line (4) and oil
return line (6) (not shown) as a unit.
3. Install eight nuts (9). Tighten the nuts to a torque of 41 N·m (30 lb ft).
Note: Two nuts are installed on each turbocharger mounting stud.
Illustration 2 g00812846
4. Slide hose (7) down the oil return line (6) onto fitting (8) .
5. Tighten two clamps (5) on hose (7) .
6. Connect oil supply line (4) to the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:19:09 UTC+0800 2020
2/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565722
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00605454
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 1. Remove the nuts (1) and washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
2. Remove exhaust manifold (2) from the cylinder head assembly.
3. Remove exhaust manifold gasket (3) that is located between exhaust manifold (2) and the
cylinder head assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00605454
1. Install exhaust manifold gasket (3) between exhaust manifold (2) and the cylinder head
assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
2. Place exhaust manifold (2) in position on the cylinder head.
3. Install the nuts (1) and the washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 4. Tighten exhaust manifold nuts (1) to a torque of 18 ± 4 N·m (13 ± 3 lb ft).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:20:08 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615211
Air Inlet Heater - Remove and Install
SMCS - 1090-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611147
1. Loosen hose clamp (1) that secures air inlet hose (2) to air inlet elbow (4) .
2. Disconnect air inlet hose (2) from air inlet elbow (4) .
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 3. Remove four bolts (3) and washers that secure the following items to the air inlet manifold:
air inlet elbow (4), gasket (5), air inlet heater (6) and gasket (7) .
Illustration 2 g00611165
4. Remove the following items from the air inlet manifold: air inlet elbow (4), gasket (5), air
inlet heater (6) and gasket (7) .
Note: Check the condition of the gaskets that are used between the elbow and the air inlet
heater. Check the gaskets between the air inlet heater and the air inlet manifold. If the
gaskets are damaged in any way, replace the gaskets.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g00611165
Note: Check condition of the gaskets for the air inlet elbow and the air inlet heater. If the
gaskets are damaged, use a new part for replacement. The wire mesh gasket (7) is installed
between the air inlet manifold and the air inlet heater.
1. Place the following items in position on the air inlet manifold: gasket (7), the air inlet heater
(6), gasket (5) and the air inlet elbow (4) .
Illustration 4 g00611147
2. Install four bolts (3) that secure the following items to the air inlet manifold: gasket (7), the
air inlet heater (6), gasket (5) and the air inlet elbow (4)
Tighten bolts (3) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
3. Connect air inlet hose (2) to air inlet elbow (4) .
4. Tighten hose clamp (1) that secures the air inlet hose to the air inlet elbow.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:21:08 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01575215
Inlet Manifold - Remove
SMCS - 1058-011
Removal Procedure
Start By:
A. Remove fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
B. Remove fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
C. Remove the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...