This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The document describes the required tools and provides a step-by-step procedure for removing the old seals and installing new ones. It also includes guidelines for cleaning parts and contains illustrations supporting the instructions.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...tuzhiyou2
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, and engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new seals, filters, and coolers, checking for wear and contaminants, and ensuring proper lubrication. Safety notices are included to handle fluids and contain contaminants properly.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...qfyc504378
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Cautions are provided regarding containing fluids, collecting waste, and preventing rapid wear from contaminants.
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Safety notices are provided regarding containing fluids, collecting waste, and preventing contact with hot oil or components.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...lituo39419496
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...tuzhiyou2
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. New gaskets are also replaced.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...tuzhiyou2
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, and engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new seals, filters, and coolers, checking for wear and contaminants, and ensuring proper lubrication. Safety notices are included to handle fluids and contain contaminants properly.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...qfyc504378
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Cautions are provided regarding containing fluids, collecting waste, and preventing rapid wear from contaminants.
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Safety notices are provided regarding containing fluids, collecting waste, and preventing contact with hot oil or components.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...lituo39419496
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...tuzhiyou2
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. New gaskets are also replaced.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...f7djidksmd3e
This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and grease to bearings and installing them into the swing drive housing along with the pinion shaft and bearing cage.
3. Heating and pressing bearings onto the pinion shaft and installing the assembly into the swing drive housing using a press.
4. Temporarily installing bolts to hold the bearing cage aligned with the housing. The instructions provide details on lubricants to use and proper positioning of parts.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...f7djidksmd3e
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing.
2. Remove the rear cover and gasket.
3. Remove the rear power take-off (RPTO) and O-ring seal.
This document provides instructions for disassembling and assembling the travel motor on Caterpillar 345B and 345B L Excavator models. It lists required tools and parts and provides 32 numbered steps to fully disassemble the travel motor by removing components like brackets, covers, pistons, plates, seals, and housing pieces. Illustrations accompany each step to show how to position the motor and parts for disassembly and reassembly. Safety notices are also included to handle parts and fluids properly.
Caterpillar Cat 340D2 L Excavator (Prefix HHK) Service Repair Manual (HHK0000...f7djidksmd3e
The document provides instructions for disassembling the final drive of an excavator model 340D2 L. It describes 25 steps to remove components such as gears, shafts, seals, bearings and housings. Various tools are required including link brackets and forcing bolts to compress springs. Personal protective equipment is recommended as parts can be propelled by released spring forces. The total weight of the final drive assembly is approximately 550 kg.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...f7djidksmd3e
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing the parts in reverse order of removal.
3) Installing the engine oil filter base on the engine, including attaching hoses and bolts.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and provides details on lubricating parts and ensuring proper alignment of components like the cam plate and brake piston. Special tools are required for tasks like removing the rotating assembly and installing seals and bearings.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f7djidksmd3e
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hoses, removing bolts and other fasteners, and using lifting devices. A 7 step disassembly procedure is also provided which involves cleaning, positioning, and separating the swivel's outer housing and rotor components using bolts, washers, and specialized tooling. Personal protective equipment is recommended when handling fluids.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...f7djidksmd3e
This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and grease to bearings and installing them into the swing drive housing along with the pinion shaft and bearing cage.
3. Heating and pressing bearings onto the pinion shaft and installing the assembly into the swing drive housing using a press.
4. Temporarily installing bolts to hold the bearing cage aligned with the housing. The instructions provide details on lubricants to use and proper positioning of parts.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...f7djidksmd3e
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing.
2. Remove the rear cover and gasket.
3. Remove the rear power take-off (RPTO) and O-ring seal.
This document provides instructions for disassembling and assembling the travel motor on Caterpillar 345B and 345B L Excavator models. It lists required tools and parts and provides 32 numbered steps to fully disassemble the travel motor by removing components like brackets, covers, pistons, plates, seals, and housing pieces. Illustrations accompany each step to show how to position the motor and parts for disassembly and reassembly. Safety notices are also included to handle parts and fluids properly.
Caterpillar Cat 340D2 L Excavator (Prefix HHK) Service Repair Manual (HHK0000...f7djidksmd3e
The document provides instructions for disassembling the final drive of an excavator model 340D2 L. It describes 25 steps to remove components such as gears, shafts, seals, bearings and housings. Various tools are required including link brackets and forcing bolts to compress springs. Personal protective equipment is recommended as parts can be propelled by released spring forces. The total weight of the final drive assembly is approximately 550 kg.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...f7djidksmd3e
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing the parts in reverse order of removal.
3) Installing the engine oil filter base on the engine, including attaching hoses and bolts.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and provides details on lubricating parts and ensuring proper alignment of components like the cam plate and brake piston. Special tools are required for tasks like removing the rotating assembly and installing seals and bearings.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f7djidksmd3e
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hoses, removing bolts and other fasteners, and using lifting devices. A 7 step disassembly procedure is also provided which involves cleaning, positioning, and separating the swivel's outer housing and rotor components using bolts, washers, and specialized tooling. Personal protective equipment is recommended when handling fluids.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01150941
Inlet and Exhaust Valve Seals - Remove and Install
SMCS - 1104-010-SA
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-1720 Seal Pick 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00610601
Illustration 2 g00610605
1. Use Tool (A) to remove valve stem seal (1) from the inlet and exhaust valve guide.
Illustration 1 shows the removal of the valve stem seal, when the valve guide (2) is removed
from cylinder head (4) .
Illustration 2 shows the removal of the valve stem seal, while the valve guide (2) is installed
in cylinder head (4) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5P-1720 Seal Pick 1
NOTICE
Keep all parts clean from contaminants.
2/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Contaminants may cause rapid wear and shortened component life.
Note: Do not apply any oil or sealant to the mating surface of the valve seal that comes into
contact with the valve guide. When the valve seal is installed, coat the surface of the valve stem
with engine oil in order to ensure initial lubrication of the seal lip.
Illustration 3 g00610601
Illustration 4 g00610605
1. Place the new valve stem seal in position on the valve guide.
2. Use Tool (A) to assist in installing the new valve stem seal.
Illustration 3 shows the installation of the valve stem seal, when the valve guide (2) is
removed from the cylinder head (4) .
Illustration 4 shows the installation of the valve stem seal, while the valve guide (2) is
installed in the cylinder head (4) .
Note: After the valve stem seal is installed on the valve guide, ensure that the seal is
properly installed in the groove of the valve guide.
3/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:19:02 UTC+0800 2020
4/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565892
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813775
Illustration 2 g00813789
1. Use Tool (A) and remove oil filter (2) from engine oil filter base (3) .
2. Remove the bolts (1) and washers from the engine oil filter base (3) .
3. Remove engine oil filter base (3) from the engine.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 4. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
worn or damaged.
Illustration 3 g00813823
5. If necessary, remove eight bolts (6) and the washers in order to remove plate (5) from the
engine.
6. Check the condition of gasket (not shown). Replace the gasket, if the gasket is worn or
damaged.
7. Check engine oil filter base (3) and plate (5) for clogging and cracks. Replace damaged
components with replacement parts.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:19:58 UTC+0800 2020
3/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565969
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00813823
1. Secure gasket and plate (5) to the cylinder block with eight bolts (6) .
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g00813789
2. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
damaged.
Note: Coat all of the O-ring seals with clean engine oil prior to installation.
3. Install the O-ring seals (4) on engine oil filter base (3) .
Illustration 3 g00813775
4. Secure engine oil filter base (3) to the plate (5) with four bolts (1) and the washers.
5. Install the engine oil filter (2) to the engine oil filter base (3) .
Note: Follow the installation procedure on the engine oil filter in order to install the engine
oil filter on the engine oil filter base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:20:54 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615275
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00611319
1. If necessary, remove bolt (1) and the washer from the cylinder head.
2. Remove oil tube assembly (dipstick) (2) from the cylinder block.
3. Check O-ring seal (3) (not shown) for wear or damage. Replace the O-ring seal, if the O-
ring seal is worn or damaged.
Illustration 2 g00611320
4. Remove bolts (4) and the washers that secure the oil cooler to the engine cylinder block.
The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers.
5. Remove engine oil cooler (5) and gasket (6) (not shown) from the engine cylinder block.
Check the gasket for wear or damage. Replace the gasket, if the gasket is worn or damaged.
Note: Check the oil cooler cover for cracks. Replace the cover, if the cover is cracked.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:21:49 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152039
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
A. Remove the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00618921
Illustration 2 g00611507
1. Remove four nuts (1) and the washers from the oil cooler core (3) .
2. Remove oil cooler core (3) from oil cooler cover (2) .
Note: Check the engine oil cooler core for cracks, clogging, and ruptures.
3. Remove two gaskets (4) from the oil cooler core. Check the gasket for wear or damage.
Replace the gaskets, if necessary.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152137
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00618921
Illustration 2 g00611507
1. Install two gaskets (4) onto the oil cooler core (3) .
2. Install the oil cooler cover (2) onto the oil cooler core (3) .
3. Install four nuts (1) and the washers, which secure the oil cooler core to the oil cooler cover.
4. Tighten the four nuts (1) .
End By: Install the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:23:41 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615279
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611320
1. Install engine oil cooler (5) and new gasket (6) (not shown). Ensure that all mating surfaces
are clean. Install bolts (4) and washers in order to secure the engine oil cooler to the engine
cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16
bolts and washers.
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g00611319
2. Install oil tube assembly (dipstick) (2) into the cylinder block.
Note: Apply clean engine oil to the O-ring seal (3) (not shown) before installation.
3. Install bolt (1) and the washer into the cylinder head.
End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:24:37 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615285
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00607236
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g00607247
1. Remove threaded plug (1) and the shim (2) for the engine oil relief valve from the right side
of the cylinder block.
2. Remove the spring (3) and spring seat (4) from the cylinder block.
Note: Check the spring seat (4) and the valve seat for an abnormal contact pattern. Inspect the
spring (3) for weakness or damage. If necessary, replace the engine oil relief valve with a new
part.
Note: Check the cylinder block for oil passages that are clogged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g00607247
Illustration 4 g00607236
1. Install spring seat (4) and spring (3) in the cylinder block.
2. Install shim (2) and threaded plug (1) in the cylinder block.
3. Tighten threaded plug (1) of the engine oil relief valve to a torque of 49 ± 5 N·m (36 ± 4 lb
ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 343 ± 20 kPa (50 ± 3 psi). Make adjustments by shimming, if necessary.
For more information, refer to Specifications, "Engine Oil Relief Valve".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:25:33 UTC+0800 2020
3/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615293
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00607679
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g00607688
1. Remove threaded plug (1) for the engine oil bypass valve from the cylinder block (2) .
2. Remove shim (3) from the cylinder block (2) .
3. Remove spring (4) from the cylinder block (2) .
4. Remove spring seat (5) from the cylinder block (2) .
Note: Check the spring seat (5) and the valve seat for an abnormal contact pattern. Inspect the
spring (4) for weakness or damage. If necessary, replace the engine oil bypass valve with a new
part.
Note: Check the cylinder block (2) for oil passages that are clogged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 3 g00607688
Illustration 4 g00607679
1. Install spring seat (5) (not shown) and spring (4) in the cylinder block (2) .
2. Install shim (3) and threaded plug (1) in the cylinder block (2) .
3. Tighten the threaded plug (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 981 ± 98 kPa (142 ± 14 psi). Make adjustments by shimming, if necessary.
For information on testing the engine oil relief valve, refer to Testing and Adjusting, "Lubrication
System".
For more information, refer to Specifications, "Engine Oil Bypass Valve".
End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:26:28 UTC+0800 2020
3/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146335
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much
for your reading.
Please click here to buy
After you pay.
Then, you can
download the complete
manual instantly.
No waiting.
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolt (1) from the cover (2) .
2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not
shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged.
Illustration 2 g00607770
2/5
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
Illustration 3 g00607857
4. Position the front housing on a work bench in order to remove the oil pump gear from the
rear of the housing.
5. Use Tool (A) to remove oil pump gear (6) from the front housing.
Illustration 4 g00607885
6. Position the front housing on a work bench in order to remove the drive gear from the front
of the housing.
7. Remove drive gear (7) from the front housing.
3/5
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...