The document provides instructions for removing and installing a diesel particulate filter on a Caterpillar 308E2CR Mini Hydraulic Excavator. It describes disconnecting sensors and tubes, removing mounting bolts, and cleaning or replacing the filter assembly. Torque specifications are listed for reinstalling components. Safety precautions are noted regarding protective equipment for handling used filters.
Caterpillar cat 308 e2cr mini hydraulic excavator (prefix fjx) service repair...fjkskekdmmenm
The document provides instructions for removing and installing components of a Diesel Particulate Filter (DPF) and various engine parts, including:
- Disassembling and cleaning the DPF
- Reassembling the DPF
- Removing and installing the DPF, inlet manifold, and inlet/exhaust valve springs
The procedures include safety precautions and lists of required tools. Steps describe disconnecting sensors and tubes, removing mounting bolts/hardware, and reinstalling parts in reverse order. Torque specifications are provided for fasteners.
Caterpillar cat 308 e2cr mini hydraulic excavator (prefix fjx) service repair...fujsekfsmemm
The document provides instructions for removing and installing components of a Diesel Particulate Filter (DPF) and various engine parts, including:
- Disassembling and cleaning the DPF
- Reassembling the DPF
- Removing and installing the DPF, inlet manifold, and inlet/exhaust valve springs
The procedures include safety precautions and lists of required tools. Steps describe disconnecting sensors and tubes, removing mounting bolts/hardware, and reinstalling parts in reverse order. Torque specifications are provided for fasteners.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...shenjiao97221
The document provides instructions for removing and installing the diesel particulate filter on a 308E2 CR Mini Hydraulic Excavator FJX powered by a C3.3B engine. It describes removing temperature sensors, tubes, and other components to separate the filter assembly. Instructions are given to clean the filter and reassemble it in reverse order. Safety precautions are listed, such as wearing protective equipment when handling used filters.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...xie25190
The document provides instructions for removing and installing a diesel particulate filter from a 308E2 CR Mini Hydraulic Excavator FJX00001-UP powered by a C3.3B engine. It describes disconnecting sensors and tubes, removing mounting bolts, and separating filter components. Instructions are given to clean the filter and register new component serial numbers. The assembly procedure outlines installing components in reverse order and proper tightening torques.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...s20y0196u
The document provides instructions for removing and installing the diesel particulate filter on a 308E2 CR Mini Hydraulic Excavator FJX powered by a C3.3B engine. It describes removing temperature sensors, tubes, and other components to separate the filter assembly. Instructions are given to clean the filter and reassemble it in reverse order. Safety precautions are listed, such as wearing protective equipment when handling used filters.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...jiduanbu
The document provides instructions for disassembling and assembling the diesel particulate filter of a Caterpillar 308E2CR Mini Hydraulic Excavator engine. It describes removing temperature sensors, tubes, and other components from the filter body and collar. It then explains cleaning the filter and reversing the process to reassemble the components and sensors back onto the filter housing. Proper safety precautions and torque specifications are listed to correctly service the diesel particulate filter.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...iphg8793466
The document provides instructions for removing and installing a diesel particulate filter from a 308E2 CR Mini Hydraulic Excavator FJX00001-UP powered by a C3.3B engine. It describes disconnecting sensors and tubes, removing mounting bolts, and separating filter components. Instructions are given to clean the filter and register new component serial numbers. The assembly procedure outlines installing components in reverse order and proper tightening torques.
Caterpillar cat 308 e2cr mini hydraulic excavator (prefix my2) service repair...fjjsekfksmem
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator MY2, including:
- Exhaust gas recirculation valve
- Fumes disposal filter
- Exhaust manifold
- Diesel particulate filter
The steps include draining coolant, removing bolts and hoses, and reinstalling components in the reverse order, applying anti-seize compound to bolts and ensuring proper torque specifications. Safety precautions are provided to avoid burns from hot components.
Caterpillar cat 308 e2cr mini hydraulic excavator (prefix fjx) service repair...fjkskekdmmenm
The document provides instructions for removing and installing components of a Diesel Particulate Filter (DPF) and various engine parts, including:
- Disassembling and cleaning the DPF
- Reassembling the DPF
- Removing and installing the DPF, inlet manifold, and inlet/exhaust valve springs
The procedures include safety precautions and lists of required tools. Steps describe disconnecting sensors and tubes, removing mounting bolts/hardware, and reinstalling parts in reverse order. Torque specifications are provided for fasteners.
Caterpillar cat 308 e2cr mini hydraulic excavator (prefix fjx) service repair...fujsekfsmemm
The document provides instructions for removing and installing components of a Diesel Particulate Filter (DPF) and various engine parts, including:
- Disassembling and cleaning the DPF
- Reassembling the DPF
- Removing and installing the DPF, inlet manifold, and inlet/exhaust valve springs
The procedures include safety precautions and lists of required tools. Steps describe disconnecting sensors and tubes, removing mounting bolts/hardware, and reinstalling parts in reverse order. Torque specifications are provided for fasteners.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...shenjiao97221
The document provides instructions for removing and installing the diesel particulate filter on a 308E2 CR Mini Hydraulic Excavator FJX powered by a C3.3B engine. It describes removing temperature sensors, tubes, and other components to separate the filter assembly. Instructions are given to clean the filter and reassemble it in reverse order. Safety precautions are listed, such as wearing protective equipment when handling used filters.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...xie25190
The document provides instructions for removing and installing a diesel particulate filter from a 308E2 CR Mini Hydraulic Excavator FJX00001-UP powered by a C3.3B engine. It describes disconnecting sensors and tubes, removing mounting bolts, and separating filter components. Instructions are given to clean the filter and register new component serial numbers. The assembly procedure outlines installing components in reverse order and proper tightening torques.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...s20y0196u
The document provides instructions for removing and installing the diesel particulate filter on a 308E2 CR Mini Hydraulic Excavator FJX powered by a C3.3B engine. It describes removing temperature sensors, tubes, and other components to separate the filter assembly. Instructions are given to clean the filter and reassemble it in reverse order. Safety precautions are listed, such as wearing protective equipment when handling used filters.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...jiduanbu
The document provides instructions for disassembling and assembling the diesel particulate filter of a Caterpillar 308E2CR Mini Hydraulic Excavator engine. It describes removing temperature sensors, tubes, and other components from the filter body and collar. It then explains cleaning the filter and reversing the process to reassemble the components and sensors back onto the filter housing. Proper safety precautions and torque specifications are listed to correctly service the diesel particulate filter.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...iphg8793466
The document provides instructions for removing and installing a diesel particulate filter from a 308E2 CR Mini Hydraulic Excavator FJX00001-UP powered by a C3.3B engine. It describes disconnecting sensors and tubes, removing mounting bolts, and separating filter components. Instructions are given to clean the filter and register new component serial numbers. The assembly procedure outlines installing components in reverse order and proper tightening torques.
Caterpillar cat 308 e2cr mini hydraulic excavator (prefix my2) service repair...fjjsekfksmem
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator MY2, including:
- Exhaust gas recirculation valve
- Fumes disposal filter
- Exhaust manifold
- Diesel particulate filter
The steps include draining coolant, removing bolts and hoses, and reinstalling components in the reverse order, applying anti-seize compound to bolts and ensuring proper torque specifications. Safety precautions are provided to avoid burns from hot components.
Caterpillar cat 308 e2cr mini hydraulic excavator (prefix my2) service repair...fujsjekskem
The document provides instructions for removing and installing components on a 308E2CR Mini Hydraulic Excavator engine, including the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are outlined that involve draining coolant, wearing protective equipment when handling hot or hazardous parts, and containing fluids during repair work. The procedures describe removing and installing parts like hoses, sensors, brackets, and filters, noting torque specifications for reinstallation.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fusjekkdmdmd2w
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f8usejkddmmd
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or threads.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...jfksemmdm3e
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f8useudjkddmm2
The document provides instructions for removing and installing components related to emissions control on a Caterpillar 308E2CR mini hydraulic excavator engine. It describes removing the exhaust gas recirculation valve by draining coolant, removing bolts and hoses, and disconnecting electrical connections. It also details removing the diesel particulate filter by marking positions, removing sensors and bolts, and cleaning components before reassembling in reverse order. Safety precautions are provided throughout for hot and pressurized fluids.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f7usueijdkdmm3e
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f7useijdkdmdm
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...itj79143591
The document provides instructions for removing and installing components related to emissions control on a Caterpillar 308E2CR mini hydraulic excavator engine. It describes removing the exhaust gas recirculation valve by draining coolant, removing bolts and hoses, and disconnecting electrical connections. It also details removing the diesel particulate filter by marking positions, removing sensors and bolts, and cleaning components before reassembling in reverse order. Safety precautions are provided throughout for hot and pressurized fluids.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fujsekmdd8di
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fusekddmm3e
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fujskkmdmd
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fjskekmdmdm1
The document provides instructions for removing and installing components related to emissions control on a Caterpillar 308E2CR mini hydraulic excavator engine. It describes removing the exhaust gas recirculation valve by draining coolant, removing bolts and hoses, and disconnecting electrical connections. It also details removing the diesel particulate filter by marking positions, removing sensors and bolts, and cleaning components before reassembling in reverse order. Safety precautions are provided throughout for hot and pressurized fluids.
This document provides instructions for assembling the final drive of an excavator model 329D L. It lists the required tools and parts. The procedure involves installing bearings in the main housing and motor housing using a press to apply the proper preload. Shims are used to take up any clearance between the housings. Duo-Cone seals are installed in the housings using a special tool. Cleanliness is emphasized throughout the assembly process.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals, and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 428 SERIES II BACKHOE LOADER (Prefix 6TC) Service Repair Manu...jkdkkdsmmd
The document provides instructions for disassembling and assembling the rear axle group and differential of a 428 Series II Backhoe Loader. It describes removing and installing the rear axle group which involves disconnecting linkages, brackets, and mounting hardware. Steps are provided to disassemble the rear axle group into individual components like housing, gears, and brakes. The differential is also disassembled by removing case halves, bearings, gears, and other parts. Precise assembly steps list installing components in reverse order and include details like torque specifications.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before separating assembly components.
3. Reassembling the spring assembly in the tooling bench and using hydraulic force to compress the spring into position, requiring several tons of force. Proper centering and leveling of the assembly is critical.
This document provides the installation procedure for a final drive on an excavator. It lists the required tools and parts. The procedure involves using lifting devices to position the final drive, applying anti-seize compound to bolts, and torquing the bolts to the specified values. It also describes attaching lifting brackets and removing the lifting equipment once installation is complete.
The document is a service repair manual that provides step-by-step instructions for disassembling the final drive components of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, carrier assembly, planetary gears, and separating the sprocket housing from the motor housing. Detailed illustrations accompany each step to show how to remove individual parts like seals, shafts, and bearings from within the final drive assembly. Special tools are listed that may be required for tasks like removing retaining rings.
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into a motor housing in the correct order.
3. Attaching lifting devices and link brackets to install the assembled swing motor and remove the swing drive, which each weigh over 500 lbs.
This document provides instructions for removing and installing a swing motor on an excavator model 329D2 L. The removal procedure involves draining oil from the swing drive, using tools to remove bolts securing the swing drive, and using lifting equipment to remove the swing motor due to its weight of approximately 77 kg. The installation procedure outlines connecting harness assemblies, hoses, and tightening connections to specified torques.
More Related Content
Similar to Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair Manual Instant Download.pdf
Caterpillar cat 308 e2cr mini hydraulic excavator (prefix my2) service repair...fujsjekskem
The document provides instructions for removing and installing components on a 308E2CR Mini Hydraulic Excavator engine, including the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are outlined that involve draining coolant, wearing protective equipment when handling hot or hazardous parts, and containing fluids during repair work. The procedures describe removing and installing parts like hoses, sensors, brackets, and filters, noting torque specifications for reinstallation.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fusjekkdmdmd2w
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f8usejkddmmd
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or threads.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...jfksemmdm3e
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f8useudjkddmm2
The document provides instructions for removing and installing components related to emissions control on a Caterpillar 308E2CR mini hydraulic excavator engine. It describes removing the exhaust gas recirculation valve by draining coolant, removing bolts and hoses, and disconnecting electrical connections. It also details removing the diesel particulate filter by marking positions, removing sensors and bolts, and cleaning components before reassembling in reverse order. Safety precautions are provided throughout for hot and pressurized fluids.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f7usueijdkdmm3e
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...f7useijdkdmdm
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...itj79143591
The document provides instructions for removing and installing components related to emissions control on a Caterpillar 308E2CR mini hydraulic excavator engine. It describes removing the exhaust gas recirculation valve by draining coolant, removing bolts and hoses, and disconnecting electrical connections. It also details removing the diesel particulate filter by marking positions, removing sensors and bolts, and cleaning components before reassembling in reverse order. Safety precautions are provided throughout for hot and pressurized fluids.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fujsekmdd8di
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fusekddmm3e
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fujskkmdmd
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fjskekmdmdm1
The document provides instructions for removing and installing components related to emissions control on a Caterpillar 308E2CR mini hydraulic excavator engine. It describes removing the exhaust gas recirculation valve by draining coolant, removing bolts and hoses, and disconnecting electrical connections. It also details removing the diesel particulate filter by marking positions, removing sensors and bolts, and cleaning components before reassembling in reverse order. Safety precautions are provided throughout for hot and pressurized fluids.
Similar to Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair Manual Instant Download.pdf (12)
This document provides instructions for assembling the final drive of an excavator model 329D L. It lists the required tools and parts. The procedure involves installing bearings in the main housing and motor housing using a press to apply the proper preload. Shims are used to take up any clearance between the housings. Duo-Cone seals are installed in the housings using a special tool. Cleanliness is emphasized throughout the assembly process.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals, and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 428 SERIES II BACKHOE LOADER (Prefix 6TC) Service Repair Manu...jkdkkdsmmd
The document provides instructions for disassembling and assembling the rear axle group and differential of a 428 Series II Backhoe Loader. It describes removing and installing the rear axle group which involves disconnecting linkages, brackets, and mounting hardware. Steps are provided to disassemble the rear axle group into individual components like housing, gears, and brakes. The differential is also disassembled by removing case halves, bearings, gears, and other parts. Precise assembly steps list installing components in reverse order and include details like torque specifications.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before separating assembly components.
3. Reassembling the spring assembly in the tooling bench and using hydraulic force to compress the spring into position, requiring several tons of force. Proper centering and leveling of the assembly is critical.
This document provides the installation procedure for a final drive on an excavator. It lists the required tools and parts. The procedure involves using lifting devices to position the final drive, applying anti-seize compound to bolts, and torquing the bolts to the specified values. It also describes attaching lifting brackets and removing the lifting equipment once installation is complete.
The document is a service repair manual that provides step-by-step instructions for disassembling the final drive components of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, carrier assembly, planetary gears, and separating the sprocket housing from the motor housing. Detailed illustrations accompany each step to show how to remove individual parts like seals, shafts, and bearings from within the final drive assembly. Special tools are listed that may be required for tasks like removing retaining rings.
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into a motor housing in the correct order.
3. Attaching lifting devices and link brackets to install the assembled swing motor and remove the swing drive, which each weigh over 500 lbs.
This document provides instructions for removing and installing a swing motor on an excavator model 329D2 L. The removal procedure involves draining oil from the swing drive, using tools to remove bolts securing the swing drive, and using lifting equipment to remove the swing motor due to its weight of approximately 77 kg. The installation procedure outlines connecting harness assemblies, hoses, and tightening connections to specified torques.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling a final drive transmission. It begins by removing the final drive from the excavator and securing it to a repair stand. Various components are then removed in sequential order, including the cover, gears, carrier assembly, planetary gears, and seals. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanism. Over 30 individual steps are outlined with descriptions and illustrations.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D L Excavator (Prefix BFC) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling and assembling the transmission of a 329D L and 329D LN excavator. It lists 37 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 36 steps for assembly, reinstalling these components in reverse order and noting cleaning requirements. Precise measurements are taken to determine the correct shim thickness for preloading bearings during assembly.
This document provides instructions for disassembling and assembling the travel motor of a 320D2L excavator. The disassembly process involves removing 27 components from the travel motor body and head. The assembly process reverses the disassembly steps and cautions that all components must be reinstalled in their original positions and orientations. Proper cleaning of components before and after disassembly and assembly is emphasized to prevent contamination of the hydraulic system.
This document provides instructions for servicing the air conditioning system on Caterpillar 322 and 322L excavators. It describes safety precautions when working with refrigerant and outlines procedures for preparing the machine, removing and installing components like lines, the compressor, and performing functions like evacuating and charging the system. Personal protective equipment is required as the system is pressurized and contains refrigerant that can cause injury.
This document provides instructions for removing and installing a governor and fuel injection control linkage on an excavator. It begins with an overview of the required tools. The removal procedure involves disconnecting tubes and cables, removing clips and pins, and taking off bolts. The installation procedure specifies cleaning and lubricating parts, replacing seals, and using tools to install clips, pins and bolts in the reverse order of removal. Precautions are given to keep parts clean and check adjustments after installation.
Caterpillar Cat 320D2 L Excavator (Prefix YEA) Service Repair Manual Instant ...jkdkkdsmmd
This document provides assembly instructions for excavator models 320D2 and 320D2 L. It outlines 49 assembly steps requiring various tools. The steps include installing components like the pump housing, swashplate assemblies, shaft assemblies, barrel assemblies, port plates, head assembly, seal assembly, control linkage, and pump control components. Precautions are provided for steps involving released spring forces.
Caterpillar Cat 320D2 L Excavator (Prefix RAR) Service Repair Manual Instant ...jkdkkdsmmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C7.1 engine. It describes the required tools and outlines a multi-step process that involves positioning the piston at top dead center, compressing the valve spring with a tool to remove keepers and the spring, and reversing the process to install new springs. Safety notices are provided to wear protective equipment when working with compressed springs.
This document provides assembly instructions for excavator models 320D2 and 320D2 L. It outlines 49 assembly steps requiring various tools. The steps include installing components like the pump housing, swashplate assemblies, shaft assemblies, barrel assemblies, port plates, head assembly, seal assembly, control linkage, and pump control components. Precautions are provided for steps involving released spring forces.
The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 320D2 excavator engine. The flywheel removal procedure involves removing bolts and installing guide studs to lift the flywheel off. The crankshaft rear seal is part of a sealed assembly that must be replaced if removed. Installation involves aligning and pressing the new seal onto the crankshaft flange.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E2 CR MINI HYD EXCAVATOR FJX
Configuration: 308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C3.3B Tier 4 Final and EU Stage 3B Engines for Caterpillar Built Machines
Media Number -UENR3278-07 Publication Date -01/09/2014 Date Updated -11/07/2016
i05305970
Diesel Particulate Filter - Disassemble
SMCS - 108F-015
Disassembly Procedure
Wear goggles, gloves, protective clothing, and a National Institute for
Occupational Safety and Health (NIOSH) approved P95 or N95 half-
face respirator when handling a used Diesel Particulate Filter or
Catalytic Converter Muffler. Failure to do so could result in personal
injury.
NOTICE
Do not strike any part of the assembly of the Diesel Particulate Filter
(DPF). Do not allow any object to contact the internal element of the
DPF. If the internal element of the DPF becomes damaged, the
assembly must be replaced.
1. Mark the position of components for installation purposes.
1/2
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g03337342
Illustration 2 g03337375
2. Remove temperature sensor (1) from body assembly (8). Remove tube assemblies (4) and
pressure sensor (5).
3. Remove bolts (6). Remove body assembly (8) and gasket (12).
4. Remove bolts (7) to separate DPF filter assembly (9) from collar (10). Remove DPF filter
assembly (9).
5. Remove temperature sensor (2) from collar (10). Remove collar (10) and gasket (12).
6. Remove temperature sensor (3) from catalyst assembly (11). Remove catalyst assembly (11)
and gasket (12).
7. Clean the Diesel Particulate Filter (DPF). Refer to Special Instruction, REHS7788,
"Cleaning the Diesel Particulate Filter (DPF) on C3.3B and C3.8 Engines".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:24:55 UTC+0800 2020
2/2
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E2 CR MINI HYD EXCAVATOR FJX
Configuration: 308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C3.3B Tier 4 Final and EU Stage 3B Engines for Caterpillar Built Machines
Media Number -UENR3278-07 Publication Date -01/09/2014 Date Updated -11/07/2016
i05305971
Diesel Particulate Filter - Assemble
SMCS - 108F-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Locktite
Nickel Anti Seize 1
Wear goggles, gloves, protective clothing, and a National Institute for
Occupational Safety and Health (NIOSH) approved P95 or N95 half-
face respirator when handling a used Diesel Particulate Filter or
Catalytic Converter Muffler. Failure to do so could result in personal
injury.
NOTICE
Do not strike any part of the assembly of the Diesel Particulate Filter
(DPF). Do not allow any object to contact the internal element of the
DPF. If the internal element of the DPF becomes damaged, the
assembly must be replaced.
1/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Note: After cleaning filter assembly or installing a new filter assembly, the Ash Service must be
performed. Refer to Troubleshooting, UENR3423, "Cat ET Service Features - DPF Soot Load
Reset".
Note: When installing a new DOC or DPF, Caterpillar recommends documenting the new
component serial numbers on-line. Go to SIS Web and select "View More" under Additional
Service Information. Select the "C3.3B and C3.8 Downloads" link. The new DOC or DPF serial
numbers can be entered through the "C3.3B and C3.8 DPF / DOC Service Info Registration".
Illustration 1 g03337342
Illustration 2 g03337375
2/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 3 g03337490
1. Apply Tooling (A) onto the threads of temperature sensor (3). Install gasket (12) and
temperature sensor (3) onto catalyst assembly (11). Tighten temperature sensor (3) to a
torque of 30 ± 5 N·m (22 ± 3 lb ft).
2. Apply Tooling (A) onto the threads of temperature sensor (2). Install collar (10), gasket
(12), and temperature sensor (2) onto catalyst assembly (11). Tighten temperature sensor (2)
to a torque of 30 ± 5 N·m (22 ± 3 lb ft)
3. Install DPF filter assembly (9) in the correct orientation for the exhaust flow as indicated by
the arrow. Install bolts (7). Install gasket (12). Tighten bolts (7) to a torque of 49 to 64 N·m
(36 to 47 lb ft).
4. Install body assembly (8). Install bolts (6). Tighten bolts (6) to a torque of 49 to 64 N·m
(36 to 47 lb ft).
5. Apply Tooling (A) onto the threads of tube assemblies (4) and temperature sensor (1).
Install temperature sensor (1) onto body assembly (8). Install tube assemblies (4) and
pressure sensor (5). Tighten temperature sensor (1) to a torque of 30 ± 5 N·m (22 ± 3 lb ft).
Tighten tube assemblies (4) to a torque of 19 ± 3 N·m (168 ± 27 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:25:52 UTC+0800 2020
3/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E2 CR MINI HYD EXCAVATOR FJX
Configuration: 308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C3.3B Tier 4 Final and EU Stage 3B Engines for Caterpillar Built Machines
Media Number -UENR3278-07 Publication Date -01/09/2014 Date Updated -11/07/2016
i05218929
Diesel Particulate Filter - Remove and Install
SMCS - 108F-010
Removal Procedure
Wear goggles, gloves, protective clothing, and a National Institute for
Occupational Safety and Health (NIOSH) approved P95 or N95 half-
face respirator when handling a used Diesel Particulate Filter or
Catalytic Converter Muffler. Failure to do so could result in personal
injury.
The muffler, catalytic converter/muffler, and diesel particulate filter will
become extremely hot during engine operation. A hot muffler, catalytic
converter/muffler and diesel particulate filter can cause serious burns.
Allow adequate cooling time before working on or near the muffler,
catalytic converter/muffler and diesel particulate filter.
NOTICE
Do not strike any part of the assembly of the Diesel Particulate Filter
(DPF). Do not allow any object to contact the internal element of the
1/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. DPF. If the internal element of the DPF becomes damaged, the
assembly must be replaced.
Illustration 1 g03337191
1. Disconnect harness assemblies (1).
Illustration 2 g03337204
2. Remove bolts (2) and bolts (3). Disconnect harness assembly (4) from pressure sensor.
2/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 3 g03337226
3. Remove bolts (5) from DPF mount bracket.
Illustration 4 g03337243
4. Use two people to remove diesel particulate filter (6).
Illustration 5 g03337246
5. Remove temperature sensors (7). Remove pressure sensor (8) and tube assemblies (9).
Installation Procedure
1. Install diesel particulate filter (6) in the reverse order of removal.
a. Tighten bolts (5) to a torque of 52 ± 3 N·m (38 ± 2 lb ft).
b. Tighten sensors (7) to a torque of 30 ± 4 N·m (22 ± 3 lb ft).
c. Tighten tube assemblies (9) to a torque of 19 ± 3 N·m (168 ± 27 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:26:49 UTC+0800 2020
3/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E2 CR MINI HYD EXCAVATOR FJX
Configuration: 308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C3.3B Tier 4 Final and EU Stage 3B Engines for Caterpillar Built Machines
Media Number -UENR3278-07 Publication Date -01/09/2014 Date Updated -11/07/2016
i05227613
Inlet Manifold - Remove and Install
SMCS - 1058-010
Removal Procedure
Start By:
a. Remove fuel manifold.
b. Remove exhaust gas recirculation valve.
Note: Refer to Specification UENR3421 "Engine Design" for non-specified engine Torque
Values.
Illustration 1 g03339493
1. Disconnect hose assembly (1) and relocate.
2. Remove bolt (2) and remove tube assembly (3).
3. Remove bolts (4) to remove inlet manifold (5) and the gasket.
1/2
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Installation Procedure
1. Install inlet manifold (5) in the reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:27:46 UTC+0800 2020
2/2
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E2 CR MINI HYD EXCAVATOR FJX
Configuration: 308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C3.3B Tier 4 Final and EU Stage 3B Engines for Caterpillar Built Machines
Media Number -UENR3278-07 Publication Date -01/09/2014 Date Updated -11/07/2016
i05224034
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
7F-4292 Valve Spring Compressor 1
9U-6144 Adapter 1
Start By:
a. Remove the rocker shaft and push rod.
Note: Refer to Specification UENR3421 "Engine Design" for non-specified engine Torque
Values.
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head
that has been removed from the engine.
Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed.
Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder
bore.
1/4
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g02799356
Illustration 2 g02725099
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
2/4
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. 1. Follow Step 1.a through Step 1.d in order to position the appropriate piston at top dead
center.
a. Install Tooling (A) in position on the cylinder head in order to compress a valve
spring (4) for the appropriate piston.
b. Use Tooling (A) in order to compress valve spring (4) and open the valve slightly.
Note: Do not compress the spring so that valve spring retainer (3) touches the valve
stem seal.
c. Rotate the crankshaft carefully, until the piston touches the valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in
bent valve stems.
d. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A)
until the piston is at the top dead center position. The valve is now held in a position
that allows the valve spring to be safely removed.
Note: If all valve springs require replacement, the procedure can be carried out on two
cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before
changing from one pair of cylinders to another pair of cylinders.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
2. Remove valve cap (1). Apply sufficient pressure to Tooling (A) in order to allow removal of
valve keepers (2).
Note: Do not compress the spring so that valve spring retainer (3) touches the valve stem
seal.
3. Slowly release pressure on Tooling (A).
4. Remove valve spring retainer (3) and remove valve spring (4).
3/4
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 3 g02725101
5. Remove Tooling (A).
6. Remove valve stem seals (5).
7. Repeat Step 2 through Step 5 in order to remove the remaining valve springs from the
appropriate cylinder.
Installation Procedure
1. Install the inlet and exhaust valve springs in the reverse order of removal.
Illustration 4 g02862476
a. Install valve springs with the smaller pitch end (6) downward on cylinder head side.
b. Inspect valve springs (4) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves " for further information.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:28:43 UTC+0800 2020
4/4
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E2 CR MINI HYD EXCAVATOR FJX
Configuration: 308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C3.3B Tier 4 Final and EU Stage 3B Engines for Caterpillar Built Machines
Media Number -UENR3278-07 Publication Date -01/09/2014 Date Updated -11/07/2016
i05224035
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove cylinder head.
Note: Refer to Specification UENR3421 "Engine Design" for non-specified engine Torque
Values.
1. Clean the bottom mating surface of the cylinder head. Check the depth of the valves below
the face of the cylinder head before the valve springs are removed. Refer to Specifications,
"Cylinder Head Valves" for the correct dimensions.
2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
3. Use a suitable lifting device to position the cylinder head with the valve springs upward.
The weight of the cylinder head is approximately 23 kg (51 lb).
1/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 1 g02784484
4. Install Tooling (A) in position on cylinder head (2) and compress the valve spring in order
to remove inlet and exhaust valves (1).
Illustration 2 g02788459
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
2/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 5. Apply sufficient pressure to Tooling (A) in order to remove valve keepers (3).
6. Slowly release pressure on Tooling (A).
7. Place a temporary identification mark on valve spring (5) in order to identify the correct
position.
8. Remove valve spring retainer (4). Remove valve spring (5) and inlet and exhaust valves (6).
9. Repeat Step 4 through Step 8 for the remaining valves.
10. Remove Tooling (A).
Illustration 3 g02784644
11. Remove valve stem seals (7) from cylinder head (2).
12. Use a suitable lifting device in order to turn over cylinder head (2).
13. Remove the inlet and exhaust valves.
Installation Procedure
1. Install inlet and exhaust valves (6) in the reverse order of removal.
a. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris.
Replace any components that are worn or damaged.
b. Lubricate the stems of inlet and exhaust valves (6) with clean engine oil. Install inlet
and exhaust valves (6) in the appropriate positions in the cylinder head. Check the
depth of the valves below the face of the cylinder head. Refer to System Operation,
Testing and Adjusting, "Valve Depth - Inspect" for more information.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:29:39 UTC+0800 2020
3/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
20. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E2 CR MINI HYD EXCAVATOR FJX
Configuration: 308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C3.3B Tier 4 Final and EU Stage 3B Engines for Caterpillar Built Machines
Media Number -UENR3278-07 Publication Date -01/09/2014 Date Updated -11/07/2016
i05305972
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 390-1136 Valve Guide Driver Kit 1
B 385-8470 Valve Guide Reamer 1
Start By:
a. Remove the inlet and exhaust valves.
Note: Refer to Specifications, "Engine Design" for non-specified engine torque values.
NOTICE
Removal and installation of the valve guide and valve seat must be
carried out by personnel with the correct training. Also special
machinery is required. For more information, refer to your authorized
Caterpillar dealer.
1/3
308E2 CR Mini Hydraulic Excavator FJX00001-UP (MACHINE) POWERED BY C3....
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...