The document provides instructions for disassembling and inspecting various engine components of a 303.5C Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their order of disassembly and provides illustrations showing how to remove each part. Specifications for measuring component wear limits are also provided to determine if parts need replacing.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...cdfvvv1
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It outlines the disassembly sequence and order of removal for each part, and includes illustrations showing how to measure specifications like backlash, end play, and clearances. Technicians are directed to inspect parts for wear and damage during disassembly and replace worn components.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...fikskkdmmd1
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe how to remove each component and inspect it for wear and damage based on specified limits. Illustrations are included to clarify the disassembly and inspection process for each engine part.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...fjskekfseik
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe how to remove each component and inspect it for wear and damage based on specified limits. Illustrations accompany each section to show the disassembly sequence and key parts.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...fjsjekdmmeme
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It outlines the disassembly sequence and steps to remove each part, and provides illustrations. Tolerances and limits are provided for inspecting components like gears, bearings, and shaft ends to determine if replacement is needed.
Caterpillar Cat 305C CR Mini Hydraulic Excavator (Prefix HWJ) Service Repair ...yan77xunhao
This document provides instructions for disassembling and inspecting components of a S4Q2-T engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe removing each component, measuring specifications, and inspecting parts for wear and damage. Replacement is recommended if measurement limits are exceeded. Cautions are provided regarding part identification and handling.
Caterpillar Cat 305C CR Mini Hydraulic Excavator (Prefix HWJ) Service Repair ...jdjkskmikdkmd
The document provides instructions for disassembling and inspecting various engine components of a 305C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their disassembly sequence and provides illustrations and instructions for removing each part. Tolerances and limits are provided for measuring various components like gear backlash, end play, and clearance.
Caterpillar cat 305 c cr mini hydraulic excavator (prefix hwj) service repair...fjskekfseik
This document provides instructions for disassembling and inspecting components of a S4Q2-T engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe removing each component, measuring specifications, and inspecting parts for wear and damage. Replacement is recommended if measurement limits are exceeded. Cautions are provided regarding part identification and handling.
Caterpillar cat 305 c cr mini hydraulic excavator (prefix hwj) service repair...fikskkdmmd1
The document provides instructions for disassembling and inspecting various engine components of a 305C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their disassembly sequence and provides illustrations and instructions for removing each part. Tolerances and limits are provided for measuring various components like gear backlash, end play, and clearance.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...cdfvvv1
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It outlines the disassembly sequence and order of removal for each part, and includes illustrations showing how to measure specifications like backlash, end play, and clearances. Technicians are directed to inspect parts for wear and damage during disassembly and replace worn components.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...fikskkdmmd1
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe how to remove each component and inspect it for wear and damage based on specified limits. Illustrations are included to clarify the disassembly and inspection process for each engine part.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...fjskekfseik
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe how to remove each component and inspect it for wear and damage based on specified limits. Illustrations accompany each section to show the disassembly sequence and key parts.
Caterpillar cat 303 c cr mini hydraulic excavator (prefix bxt) service repair...fjsjekdmmeme
This document provides instructions for disassembling and inspecting various engine components of a 303C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It outlines the disassembly sequence and steps to remove each part, and provides illustrations. Tolerances and limits are provided for inspecting components like gears, bearings, and shaft ends to determine if replacement is needed.
Caterpillar Cat 305C CR Mini Hydraulic Excavator (Prefix HWJ) Service Repair ...yan77xunhao
This document provides instructions for disassembling and inspecting components of a S4Q2-T engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe removing each component, measuring specifications, and inspecting parts for wear and damage. Replacement is recommended if measurement limits are exceeded. Cautions are provided regarding part identification and handling.
Caterpillar Cat 305C CR Mini Hydraulic Excavator (Prefix HWJ) Service Repair ...jdjkskmikdkmd
The document provides instructions for disassembling and inspecting various engine components of a 305C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their disassembly sequence and provides illustrations and instructions for removing each part. Tolerances and limits are provided for measuring various components like gear backlash, end play, and clearance.
Caterpillar cat 305 c cr mini hydraulic excavator (prefix hwj) service repair...fjskekfseik
This document provides instructions for disassembling and inspecting components of a S4Q2-T engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe removing each component, measuring specifications, and inspecting parts for wear and damage. Replacement is recommended if measurement limits are exceeded. Cautions are provided regarding part identification and handling.
Caterpillar cat 305 c cr mini hydraulic excavator (prefix hwj) service repair...fikskkdmmd1
The document provides instructions for disassembling and inspecting various engine components of a 305C CR Mini Hydraulic Excavator, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. It lists the components in their disassembly sequence and provides illustrations and instructions for removing each part. Tolerances and limits are provided for measuring various components like gear backlash, end play, and clearance.
Caterpillar cat 305 c cr mini hydraulic excavator (prefix hwj) service repair...cdfvvv1
This document provides instructions for disassembling and inspecting components of a S4Q2-T engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe removing each component, measuring specifications, and inspecting parts for wear and damage. Replacement is recommended if measurement limits are exceeded. Cautions are provided regarding part identification and handling.
Caterpillar Cat 304D CR Mini Excavator (Prefix TYK) Service Repair Manual (TY...jdjkskmikdkmd
The document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The disassembly sequence and inspection steps are described in detail along with acceptable tolerance limits for various components. Dismantling is to be done in the specified order and all gaskets and seals replaced during reassembly.
Caterpillar cat 304 d cr mini excavator (prefix tyk) service repair manual (t...cdfvvv1
The document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The disassembly sequence and inspection steps are described in detail along with acceptable tolerance limits for various components. Dismantling is to be done in the specified order and all gaskets and seals replaced during reassembly.
Caterpillar cat 304 d cr mini excavator (prefix tyk) service repair manual (t...fikskkdmmd1
This document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The 10-page document outlines the disassembly sequence and provides illustrations to remove each component. Technicians are instructed to inspect parts for wear and damage, measure component clearances, and replace worn parts.
Caterpillar Cat 304D CR Mini Excavator (Prefix TYK) Service Repair Manual Ins...jiuliu14811471
The document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The disassembly sequence and inspection steps are described in detail along with acceptable tolerance limits for various components. Dismantling is to be done in the specified order and all gaskets, seals, and O-rings are to be replaced during reassembly.
Caterpillar Cat 303.5 D Mini Excavator (Prefix RHP) Service Repair Manual Ins...yan77xunhao
This document provides instructions for disassembling and inspecting various engine components of a 303.5 D Mini Excavator powered by an S3Q2 engine. The components include the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. Detailed steps are provided to remove each component, including any necessary safety notes. Measurement standards are given to inspect for excessive wear or damage that would require replacement of parts.
Caterpillar cat 303.5 d mini excavator (prefix rhp) service repair manual (rh...fjsjekdmmeme
The document provides instructions for disassembling and inspecting components of a 303.5 D Mini Excavator engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The steps include removing parts like the crankshaft pulley, timing gear case, idler gear, oil pan, piston rings, piston pin, and main bearing caps. Technicians are directed to inspect parts for wear and damage when disassembled and to measure specifications like backlash, end play, and clearances and replace parts if limits are exceeded. Safety notes and cautions are provided throughout the procedure.
Caterpillar Cat 303.5 D Mini Excavator (Prefix RHP) Service Repair Manual (RH...jdjkskmikdkmd
The document provides instructions for disassembling and inspecting components of a 303.5 D Mini Excavator engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The steps include removing parts like the crankshaft pulley, timing gear case, idler gear, oil pan, piston rings, piston pin, and main bearing caps. Tolerances and limits are provided for measurements of components like gear backlash, end play, and clearance. Technicians are advised to inspect parts for wear and damage during disassembly.
Caterpillar cat 303.5 d mini excavator (prefix rhp) service repair manual (rh...fikskkdmmd1
This document provides instructions for disassembling and inspecting various engine components of a 303.5 D Mini Excavator powered by an S3Q2 engine. The components include the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. Detailed steps are provided to remove each component, including any necessary safety notes. Measurement standards are listed to inspect for excessive wear or damage that would require replacement of parts.
Caterpillar cat 303.5 d mini excavator (prefix rhp) service repair manual (rh...fjskekfseik
This document provides instructions for disassembling and inspecting various engine components of a 303.5 D Mini Excavator powered by an S3Q2 engine. The components include the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. Detailed steps are provided to remove each component, including any necessary safety notes. Measurement standards are given to inspect for excessive wear or damage that would require replacement of parts.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. It describes 40 steps to disassemble the various components of the travel motor including removing seals, springs, pistons, plates, and bearings. It then describes the assembly process in reverse, providing details on cleaning parts and applying lubricant before reinstalling components in the proper order and orientation.
The document provides instructions for removing and installing a piston pump used for hoist and steering functions on a Caterpillar 725C articulated truck. The removal process involves taking off the cab, then disconnecting hydraulic lines and electrical connectors from the pump. Individual components are then removed from the pump housing in reverse order of the installation instructions. Proper safety precautions and cleaning of parts is emphasized during disassembly and reassembly.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, removing components like bolts, valves, sensors, gears, bearings and seals. It then lists 29 steps for assembly, installing these components in reverse order. Cleanliness is emphasized throughout to prevent dirt from entering components. Various tools are required, including link brackets, eyebolts and retaining ring pliers.
Caterpillar Cat 390F Mobile Hydraulic Excavator (Prefix B37) Service Repair M...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F Hydraulic Excavator. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the correct order and orientation, with notes about cleaning, marking, and applying lubricant to parts. Precautions are provided regarding spring-loaded components.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It describes 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then describes 36 steps for reassembly, including installing seals, bearings, pistons, springs and covers. Precise alignment marks are required for accurate reassembly. Cleanliness is critical and tools are needed to remove and install certain parts.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 365B L MH EXCAVATOR (Prefix CTY) Service Repair Manual (CTY00...uddksemd8ud
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Caterpillar Cat 345C L Mobile Hydraulic Excavator (Prefix M3E) Service Repair...uddksemd8ud
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, and seals. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the correct order. Contamination of hydraulic systems must be avoided during the process.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the process.
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing to access the RPTO.
2. Disconnect the drive shaft from the RPTO and remove retaining bolts.
3. Lift the RPTO straight up to remove.
More Related Content
Similar to Caterpillar Cat 303.5C CR Mini Hydraulic Excavator (Prefix DMY) Service Repair Manual (DMY00001 and up).pdf
Caterpillar cat 305 c cr mini hydraulic excavator (prefix hwj) service repair...cdfvvv1
This document provides instructions for disassembling and inspecting components of a S4Q2-T engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The multi-step procedures describe removing each component, measuring specifications, and inspecting parts for wear and damage. Replacement is recommended if measurement limits are exceeded. Cautions are provided regarding part identification and handling.
Caterpillar Cat 304D CR Mini Excavator (Prefix TYK) Service Repair Manual (TY...jdjkskmikdkmd
The document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The disassembly sequence and inspection steps are described in detail along with acceptable tolerance limits for various components. Dismantling is to be done in the specified order and all gaskets and seals replaced during reassembly.
Caterpillar cat 304 d cr mini excavator (prefix tyk) service repair manual (t...cdfvvv1
The document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The disassembly sequence and inspection steps are described in detail along with acceptable tolerance limits for various components. Dismantling is to be done in the specified order and all gaskets and seals replaced during reassembly.
Caterpillar cat 304 d cr mini excavator (prefix tyk) service repair manual (t...fikskkdmmd1
This document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The 10-page document outlines the disassembly sequence and provides illustrations to remove each component. Technicians are instructed to inspect parts for wear and damage, measure component clearances, and replace worn parts.
Caterpillar Cat 304D CR Mini Excavator (Prefix TYK) Service Repair Manual Ins...jiuliu14811471
The document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The disassembly sequence and inspection steps are described in detail along with acceptable tolerance limits for various components. Dismantling is to be done in the specified order and all gaskets, seals, and O-rings are to be replaced during reassembly.
Caterpillar Cat 303.5 D Mini Excavator (Prefix RHP) Service Repair Manual Ins...yan77xunhao
This document provides instructions for disassembling and inspecting various engine components of a 303.5 D Mini Excavator powered by an S3Q2 engine. The components include the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. Detailed steps are provided to remove each component, including any necessary safety notes. Measurement standards are given to inspect for excessive wear or damage that would require replacement of parts.
Caterpillar cat 303.5 d mini excavator (prefix rhp) service repair manual (rh...fjsjekdmmeme
The document provides instructions for disassembling and inspecting components of a 303.5 D Mini Excavator engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The steps include removing parts like the crankshaft pulley, timing gear case, idler gear, oil pan, piston rings, piston pin, and main bearing caps. Technicians are directed to inspect parts for wear and damage when disassembled and to measure specifications like backlash, end play, and clearances and replace parts if limits are exceeded. Safety notes and cautions are provided throughout the procedure.
Caterpillar Cat 303.5 D Mini Excavator (Prefix RHP) Service Repair Manual (RH...jdjkskmikdkmd
The document provides instructions for disassembling and inspecting components of a 303.5 D Mini Excavator engine, including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The steps include removing parts like the crankshaft pulley, timing gear case, idler gear, oil pan, piston rings, piston pin, and main bearing caps. Tolerances and limits are provided for measurements of components like gear backlash, end play, and clearance. Technicians are advised to inspect parts for wear and damage during disassembly.
Caterpillar cat 303.5 d mini excavator (prefix rhp) service repair manual (rh...fikskkdmmd1
This document provides instructions for disassembling and inspecting various engine components of a 303.5 D Mini Excavator powered by an S3Q2 engine. The components include the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. Detailed steps are provided to remove each component, including any necessary safety notes. Measurement standards are listed to inspect for excessive wear or damage that would require replacement of parts.
Caterpillar cat 303.5 d mini excavator (prefix rhp) service repair manual (rh...fjskekfseik
This document provides instructions for disassembling and inspecting various engine components of a 303.5 D Mini Excavator powered by an S3Q2 engine. The components include the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. Detailed steps are provided to remove each component, including any necessary safety notes. Measurement standards are given to inspect for excessive wear or damage that would require replacement of parts.
Similar to Caterpillar Cat 303.5C CR Mini Hydraulic Excavator (Prefix DMY) Service Repair Manual (DMY00001 and up).pdf (10)
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. It describes 40 steps to disassemble the various components of the travel motor including removing seals, springs, pistons, plates, and bearings. It then describes the assembly process in reverse, providing details on cleaning parts and applying lubricant before reinstalling components in the proper order and orientation.
The document provides instructions for removing and installing a piston pump used for hoist and steering functions on a Caterpillar 725C articulated truck. The removal process involves taking off the cab, then disconnecting hydraulic lines and electrical connectors from the pump. Individual components are then removed from the pump housing in reverse order of the installation instructions. Proper safety precautions and cleaning of parts is emphasized during disassembly and reassembly.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, removing components like bolts, valves, sensors, gears, bearings and seals. It then lists 29 steps for assembly, installing these components in reverse order. Cleanliness is emphasized throughout to prevent dirt from entering components. Various tools are required, including link brackets, eyebolts and retaining ring pliers.
Caterpillar Cat 390F Mobile Hydraulic Excavator (Prefix B37) Service Repair M...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F Hydraulic Excavator. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the correct order and orientation, with notes about cleaning, marking, and applying lubricant to parts. Precautions are provided regarding spring-loaded components.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It describes 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then describes 36 steps for reassembly, including installing seals, bearings, pistons, springs and covers. Precise alignment marks are required for accurate reassembly. Cleanliness is critical and tools are needed to remove and install certain parts.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 365B L MH EXCAVATOR (Prefix CTY) Service Repair Manual (CTY00...uddksemd8ud
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Caterpillar Cat 345C L Mobile Hydraulic Excavator (Prefix M3E) Service Repair...uddksemd8ud
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, and seals. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the correct order. Contamination of hydraulic systems must be avoided during the process.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the process.
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing to access the RPTO.
2. Disconnect the drive shaft from the RPTO and remove retaining bolts.
3. Lift the RPTO straight up to remove.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...uddksemd8ud
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing plugs, seals, valves, and connectors in reverse order of removal.
3) Installing the engine oil filter base on the engine using guide studs and bolts, and reconnecting hoses.
The document provides instructions for installing a fuel injection pump on a Caterpillar 330 excavator engine:
1. Install alignment tools and spacers to hold the fuel injection pump and rack in position. Lubricate seals and install the pump, securing it with a bushing.
2. Use a measurement tool to check that the rack has the proper travel of 15.70 mm after installation.
3. Repeat the process to install the remaining fuel injection pumps and reinstall the cover.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...uddksemd8ud
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hydraulic lines, removing bolts and other fasteners, and using lifting devices. A 7 step procedure is then given for disassembling the swivel once it is removed, which involves cleaning it, positioning it on a repair stand, and separating its outer housing from the rotor using bolts and other tools.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...uddksemd8ud
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and housing components are then removed to separate the rotor from the outside housing.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C MH excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly in reverse order, providing details on installing components and applying sealant or lubricant.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 303.5C MINI HYD EXCAVATOR DMY
Configuration: 303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY S3Q2 Engine
Disassembly and Assembly
S3Q2 and S3Q2-T Engines
Media Number -KENR6786-03 Publication Date -01/08/2015 Date Updated -18/08/2015
i04111938
Timing Gear, Camshaft, and Oil Pan - Disassemble and Inspect
SMCS - 1206-015; 1206-040; 1210-015; 1210-040; 1302-015; 1302-040
Disassembling and inspecting timing gear, camshaft, and oil
pan
1/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g02315293
Disassembling sequence
(1) Crankshaft pulley
(2) Cover
(3) Timing gear case
(4) Baffle plate
(5) Idler gear
(6) Oil pan
(7) Oil pump
(8) Camshaft
(9) Front plate
Removing crankshaft pulley
Note: The bar that stops the crankshaft from turning may come off. Pay due attention to safety.
2/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g02210558
1. Screw two guide bolts into the threaded holes at the rear end of the crankshaft. Stick a bar
across the guide bolts to prevent the crankshaft from turning.
2. Remove the crankshaft pulley.
3. Take out the woodruff key of the crankshaft.
Inspect the crankshaft pulley (1) for worn belt groove and worn oil seal contact surface.
Removing timing gear case
Note: The front plate is bolted to the crankcase from inside the gear case. Do not attempt to
remove the front plate together with the gear case by tapping.
3/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 3 g02210559
1. Remove bolts from the timing gear case.
2. Remove the timing gear case.
Inspect the timing gear case (3) for Crack and abnormality of knock hole.
Note: Bolts have different lengths. Pay attention to the positions of bolts to ensure correct
reassembling.
Measuring timing gear backlash
Illustration 4 g02210560
Use anyone of the following procedure to measure the backlash of the gear :
4/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. • Apply a dial gauge to the circumference of gear shaft at the right angle to the shaft.
• Insert feeler gauges into the meshing between two gears.
Replace the gear if the limit is exceeded.
Table 1
Item Standard Limit
Timing gear
backlash
Between crankshaft gear
and idler gear
0.030 to 0.160 mm (0.0012
to 0.0063 inch)
0.250 mm
(0.0098 inch)
Between idler gear and
valve camshaft gear
0.040 to 0.170 mm (0.0016
to 0.0067 inch)
Between idler gear and
pump camshaft gear
0.030 to 0.180 mm (0.0012
to 0.0071 inch)
Measuring idler gear end play
Illustration 5 g02210573
(10) Thrust plate
Using a feeler gauge or dial gauge, measure the end play of idler gear. If the measured value exceeds
the limit, replace the idler gear with the new gear.
Table 2
Item Standard Limit
5/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. End play
0.050 to 0.200 mm (0.0020 to 0.0079 inch) 0.350 mm (0.0138 inch)
Removing idler gear
Illustration 6 g02210574
1. Remove the thrust plate bolt.
2. Remove the idler gear while turning the gear.
Inspect the thrust plate and idler gear bushing for wear. Inspect the idler gear for flaking, uneven
contact, damage, and abnormal key groove condition. Inspect the plug for clogged oil holes and wear.
Measuring camshaft end play
6/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 7 g02210575
Measure the camshaft end play with the camshaft gear attached. If the limit is exceeded, replace the
thrust plate with a new one.
Table 3
Item Standard Limit
Camshaft end play
0.100 to 0.250 mm (0.0039 to 0.0098 inch) 0.300 mm (0.0118 inch)
Inverting crankcase
Note: Do not place the engine directly on the ground, which leads damage / cracking of oil pan
(6) .
7/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 8 g02315294
1. Attach the wire rope to the crankcase. Using a crane to hoist the crankcase and lay the
crankcase with the side of the crankcase facing downwards.
2. After that, hoist the crankcase again and invert the crankcase.
Removing oil pan and oil pan gasket
Illustration 9 g02210577
1. Remove the bolts from the oil pan, and remove the oil pan from crankcase.
2. Remove the oil pan gasket from crankcase.
Removing oil pump
8/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 10 g02210578
Remove the oil pump set bolts (11), and pull out the oil pump from crankcase.
Removing camshaft
Note: Be careful not to damage the cams of camshaft and the bushings.
Illustration 11 g02210579
1. Rotate the camshaft to see the thrust plate bolt through the camshaft gear hole.
2. By using the socket P/N:34491-00300 (12), remove the thrust plate bolt.
3. Remove the camshaft from the crankcase.
9/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 4. Remove the tappet.
Inspect the thrust plate and camshaft (8) for damage and wear. Replace all the gaskets, seals, and O-
rings during installation.
Removing front plate
Illustration 12 g02210580
1. Remove the front plate bolts.
2. Remove the front plate from the crankcase.
Note: If difficult to remove the front plate, lightly tap the front plate with a plastic hammer.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Mar 3 15:46:00 UTC+0800 2020
10/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED B...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 303.5C MINI HYD EXCAVATOR DMY
Configuration: 303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY S3Q2 Engine
Disassembly and Assembly
S3Q2 and S3Q2-T Engines
Media Number -KENR6786-03 Publication Date -01/08/2015 Date Updated -18/08/2015
i04111950
Piston, Connecting Rod, Crankshaft, and Cylinder Block -
Disassemble and Inspect
SMCS - 1201-015; 1201-040; 1202-015; 1202-040; 1214-015; 1214-040; 1218-015; 1218-040
Disassembling and inspecting piston, connecting rod,
crankshaft, and crankcase
1/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g02315374
Disassembling sequence
(1) Connecting rod cap
(2) Connecting rod bearing (lower)
(3) Main bearing cap
(4) Main bearing cap (lower)
(5) Crankshaft
(6) Main bearing (upper)
(7) Connecting rod
(8) Connecting rod bearing (upper)
(9) Snap ring
(10) Piston pin
(11) Piston
(12) No.1 compression ring
2/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. (13) No.2 compression ring
(14) Oil ring
(15) Tappet
(16) Crankcase
(17) Check valve
Note: When replacing the crankcase, carefully remove parts (relief valve) mounted on the non-
reusable crankcase so that can be reused.
Laying crankcase on its side
Illustration 2 g02315375
Attach the wire rope to the crankcase. By using a crane, hoist the crankcase and lay it with its side
faced downwards.
Measuring connecting rod end play
3/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 3 g02210895
1. Measure the clearance (end play) between the connecting rod big-end and crankshaft by using
the thickness gauge.
2. If the clearance beyond the limit, replace the connecting rod with new one.
Table 1
Item Standard Limit
Connecting rod end play
0.150 to 0.350 mm (0.0059 to 0.0138 inch) 0.500 mm (0.0197 inch)
Removing connecting rod cap
4/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 4 g02210896
1. Mark the cylinder number on the connecting rod and connecting rod cap.
2. Remove the connecting rod cap.
3. Be sure to make the disassembled lower connecting rod bearing easy to recognize the cylinder
number, and upper or lower.
Inspect the connecting rod cap (1) for scratches, cracks, dint, clogged oil holes, and wear.
Note: Be careful not to damage the bearings. Be sure to arrange the disassembled bearings in the
order for correct assembly.
Removing carbon deposits from the upper part of cylinder
Note: Be sure to remove carbon deposits from the upper part of the cylinder before removing
the piston. Damage the piston and piston ring.
Illustration 5 g02210934
Remove carbon deposits from the upper part of cylinder using a cloth or oil paper. Be careful not to
damage the inner surface of the cylinder.
Pulling out piston
5/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 6 g02210937
1. Turn the crankshaft to bring the piston to the top dead center.
2. Using a piece of wood such a hammer handle, push the mating surface of the connecting rod
cap. Pull the piston and connecting rod upward from the cylinder.
• Inspect the connecting rod (7) for serration for cracks, clogged oil holes, and wear.
• Inspect the connecting rod cap bolts for damaged threads.
• Inspect the piston (11) for surface scratches, cracks, damage, wear, and carbon deposits.
Removing piston ring
Illustration 7 g02210938
6/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Remove the piston rings using piston ring pliers (18). Inspect both the compression rings and oil ring
for wear, and damage.
Removing piston pin
Illustration 8 g02210939
1. Using snap ring pliers (19), remove the snap ring. Inspect the snap ring (9) for fatigue.
2. Remove the piston pin, and separate the piston from the connecting rod.
Inspect the connecting rod small end bushing for wear and clogged oil holes. Inspect the piston pin
(10) for wear.
Note: Heat the piston with a piston heater or in hot water if the piston pin is stubborn.
Uprearing crankcase
7/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 9 g02315393
Uprear the crankcase softly with upper faced downward.
Measuring crankshaft end play
Illustration 10 g02210954
1. With attach the dial gauge to top of the crankshaft, measure the end play.
2. If measured value exceeds the limit, replace the flange bearing with new one.
Table 2
Item Standard Limit
8/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Crankshaft end play
0.100 to 0.204 mm (0.0039 to 0.0080 inch) 0.300 mm (0.0118 inch)
Removing main bearing cap
Note: When removing the main bearing cap, be careful do not damage the lower main bearing
lower that are attached to the cap. Also be careful not to drop those parts, which may damage
the crankshaft.
Illustration 11 g02210955
1. Unscrew the main bearing cap bolts. Inspect the main bearing cap bolts for damaged threads.
2. Unscrew the main bearing cap. Inspect the main bearing cap for cracks.
Inspect the main bearing cap (lower) (4) for scratches on inside and outside surfaces, corrosion,
flaking, and seizing.
Note: Mark the bearings for the correct cylinder numbers.
Removing crankshaft
Note: Be careful not to damage bearings when removing the crankshaft.
9/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 12 g02315395
1. Slowly lift the crankshaft straight up.
2. Arrange the bearings in the order of disassembly so that the original positions are restored
when reassembling.
Inspect the crankcase (16) for adhesion of water scale, corrosion, and flaking. Inspect the tappet (15)
for wear.
Note: When raising the crankshaft, do not allow wire chain to come into contact with the crankshaft.
To avoid damage to the crankshaft when raising, use a cloth belt or pad. Mark the bearings for the
correct cylinder numbers.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Mar 3 15:46:57 UTC+0800 2020
10/10
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED B...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 303.5C MINI HYD EXCAVATOR DMY
Configuration: 303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY S3Q2 Engine
Disassembly and Assembly
S3Q2 and S3Q2-T Engines
Media Number -KENR6786-03 Publication Date -01/08/2015 Date Updated -18/08/2015
i04112012
Cylinder Head and Valve Mechanism - Inspect and Repair
SMCS - 1100-023; 1100-040; 1102-023; 1102-040
Measuring distortion of the bottom surface of the cylinder
head
Illustration 1 g02315433
With a straight edge placed on the bottom face of the cylinder head, measure the bottom face
distortion using a feeler gauge. If the measurement exceeds the limit, grind the bottom face using a
surface grinder.
Table 1
Item Standard Limit
1/16
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Bottom surface distortion
0.050 mm (0.0020 inch) or less 0.200 mm (0.0079 inch)
Note: Do not grind the surfaces more than 0.20 mm (0.008 inch) in total (cylinder head bottom
surface plus crankcase top surface).
Measuring clearance between rocker arm and rocker shaft
Illustration 2 g02212574
(A and B) Measuring points
Measure the inside diameter of the rocker arm and outside diameter of the rocker shaft. Replace
the rocker arm or rocker shaft if the clearance exceeds the limit.
Table 2
Item Nominal Standard Limit
Rocker arm inside
diameter
19.0 mm (0.75
inch)
19.010 to 19.030 mm
(0.7484 to 0.7492 inch)
-
Rocker shaft diameter 19.0 mm (0.75
inch)
18.980 to 19.000 mm
(0.7472 to 0.7480 inch)
-
Clearance between rocker
arm and shaft
- 0.010 to 0.050 mm (0.0004
to 0.0020 inch)
0.070 mm
(0.0028 inch)
2/16
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Measuring perpendicularity and free length of valve spring
Illustration 3 g02212575
Measure the perpendicularity and free length of the valve spring. If the limit is exceeded, replace
the valve spring with a new one.
Table 3
Item Standard Limit
Free length (D)
48.850 mm (1.9232 inch) 47.600 mm (1.8740 inch)
Perpendicularity (C)
Θ = 1.5 degrees or less
Δ (gap) = 1.30 mm (0.051 inch)
or less
Lf = 48.850 mm (1.9232 inch)
Δ = 1.50 mm (0.059 inch) over entire
length
Set length / set force
43.0 mm (1.69 inch) /
176 to 196 N (130 to 145 lbf)
43.0 mm (1.69 inch) /
147 N (108 lbf)
Measuring push rod runout
3/16
303.5C CR Mini Hydraulic Excavator DMY00001-UP (MACHINE) POWERED BY ...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...