This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators. The procedures describe disconnecting fuel lines, removing parts, cleaning, installing with new seals or O-rings, and reconnecting lines while following proper safety and contamination prevention measures.
Caterpillar cat 301.8 mini hydraulic excavator (prefix bfa) service repair ma...dfujdjkskekmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.8 mini hydraulic excavator (prefix bdh) service repair ma...dfujdjkskekmmd
This document provides instructions for removing and installing a fuel shutoff solenoid, removing and installing a fuel injection pump, and removing and installing an exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators. The instructions include safety notices and step-by-step procedures with illustrations. Torque specifications are provided for reinstalling components.
Caterpillar cat 301.8 mini hydraulic excavator (prefix 3 yw) service repair m...dfujdjkskekmmd
This document provides installation instructions for installing an engine and pumps into a 301.5, 301.6, or 301.8 mini hydraulic excavator. It outlines 42 steps to install various engine components like hoses, wires, brackets, and covers. It also provides removal and assembly instructions for a fuel filter base, including any hand priming pump components. Safety warnings are provided throughout regarding potential hazards.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjsjfjskeksmem
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w012...fjsekdmmeed
1. The document provides instructions for removing and installing the front gear group, front housing, and valve mechanism cover on a 120G Motor Grader with a 3304 engine.
2. The front gear group removal procedure involves removing bolts, plates, and gears to access the camshaft and fuel pump gears.
3. Removing the front housing requires first removing other components like the water pump and crankshaft seal. Bolts are then removed to lift off the housing and gasket.
Caterpillar cat 428 c backhoe loader (prefix 2cr) service repair manual (2cr0...uuudfjjfjkkskm
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The instructions include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing nozzles and pumps following specific tightening procedures and torque specifications. Safety notices are also provided to keep parts clean and contain fluids properly during the repair process.
Caterpillar cat d6 r track type tractor (prefix 2hm) service repair manual (2...fhhjsjekmdme
1. The document provides removal and installation instructions for the front gear group and front housing of a Caterpillar D6R track-type tractor powered by a 3306 engine.
2. The removal instructions include removing bolts, plates, and gears to remove the front gear group, and removing covers and bolts to remove the front housing.
3. The installation instructions specify cleaning and installing new gaskets, and installing components in reverse order of removal while applying thread lock compound and sealant as needed.
Caterpillar Cat 301.5, 301.6 and 301.8 Mini Hydraulic Excavator (Prefix BFA) ...f8usejkdmmd8i
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and capturing shim details for reinstallation. Safety notices recommend keeping parts clean and containing fluids during maintenance.
Caterpillar cat 301.8 mini hydraulic excavator (prefix bfa) service repair ma...dfujdjkskekmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.8 mini hydraulic excavator (prefix bdh) service repair ma...dfujdjkskekmmd
This document provides instructions for removing and installing a fuel shutoff solenoid, removing and installing a fuel injection pump, and removing and installing an exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators. The instructions include safety notices and step-by-step procedures with illustrations. Torque specifications are provided for reinstalling components.
Caterpillar cat 301.8 mini hydraulic excavator (prefix 3 yw) service repair m...dfujdjkskekmmd
This document provides installation instructions for installing an engine and pumps into a 301.5, 301.6, or 301.8 mini hydraulic excavator. It outlines 42 steps to install various engine components like hoses, wires, brackets, and covers. It also provides removal and assembly instructions for a fuel filter base, including any hand priming pump components. Safety warnings are provided throughout regarding potential hazards.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjsjfjskeksmem
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w012...fjsekdmmeed
1. The document provides instructions for removing and installing the front gear group, front housing, and valve mechanism cover on a 120G Motor Grader with a 3304 engine.
2. The front gear group removal procedure involves removing bolts, plates, and gears to access the camshaft and fuel pump gears.
3. Removing the front housing requires first removing other components like the water pump and crankshaft seal. Bolts are then removed to lift off the housing and gasket.
Caterpillar cat 428 c backhoe loader (prefix 2cr) service repair manual (2cr0...uuudfjjfjkkskm
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The instructions include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing nozzles and pumps following specific tightening procedures and torque specifications. Safety notices are also provided to keep parts clean and contain fluids properly during the repair process.
Caterpillar cat d6 r track type tractor (prefix 2hm) service repair manual (2...fhhjsjekmdme
1. The document provides removal and installation instructions for the front gear group and front housing of a Caterpillar D6R track-type tractor powered by a 3306 engine.
2. The removal instructions include removing bolts, plates, and gears to remove the front gear group, and removing covers and bolts to remove the front housing.
3. The installation instructions specify cleaning and installing new gaskets, and installing components in reverse order of removal while applying thread lock compound and sealant as needed.
Caterpillar Cat 301.5, 301.6 and 301.8 Mini Hydraulic Excavator (Prefix BFA) ...f8usejkdmmd8i
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and capturing shim details for reinstallation. Safety notices recommend keeping parts clean and containing fluids during maintenance.
Caterpillar Cat 301.5, 301.6 and 301.8 Mini Hydraulic Excavator (Prefix BFA) ...ze6074xunong
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and capturing shim details for reinstallation. Safety notices recommend keeping parts clean and containing fluids during maintenance.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...fusjekkdmdmd2w
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...fusjekkdmdmd2w
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...fusjekkdmdmd2w
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or bolting components back into place while following proper safety practices.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...f8usejkddmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...f8usejkddmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and capturing shim details for reinstallation. Safety notices recommend keeping parts clean and containing fluids during maintenance.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...f8usejkddmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and reinstalling components while taking precautions to prevent contamination.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...udjkdksmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...udjkdksmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and capturing component details for reinstallation. Safety notices emphasize keeping parts clean and containing fluids during maintenance.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...udjkdksmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
Caterpillar Cat 301.5, 301.6 and 301.8 Mini Hydraulic Excavator (Prefix BFA) ...tengtui535
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5, 301.6 and 301.8 Mini Hydraulic Excavator (Prefix BFA) ...gongfuao7509
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...idksmmdmdm
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...jkdkkdsmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...jkdkkdsmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...ufuejkdkmdm
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...ufuejkdkmdm
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...ufuejkdkmdm
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...vvnj41316031
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...vvnj41316031
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
This manual covers service procedures for Toyota forklifts with pneumatic and cushion tires. It details removal and installation procedures, inspection methods, and adjustments for various components. Reference manuals are also listed for engines and other relevant components. The manual provides specifications, torque values, and other technical information needed for repair and maintenance of these vehicles.
This document provides an overview of servicing procedures for a Toyota forklift transmission. It includes sections on removal and installation of the torque converter and transmission assembly, disassembly and inspection of the torque converter, and disassembly of the transmission assembly. Procedures are outlined in steps and key points are called out, such as match marking parts during removal and selection of spacer thickness. Standard torque specifications are provided throughout.
More Related Content
Similar to Caterpillar cat 301.8 mini hydraulic excavator (prefix bfa) service repair manual (bfa00001 and up)
Caterpillar Cat 301.5, 301.6 and 301.8 Mini Hydraulic Excavator (Prefix BFA) ...ze6074xunong
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and capturing shim details for reinstallation. Safety notices recommend keeping parts clean and containing fluids during maintenance.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...fusjekkdmdmd2w
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...fusjekkdmdmd2w
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...fusjekkdmdmd2w
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or bolting components back into place while following proper safety practices.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...f8usejkddmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...f8usejkddmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and capturing shim details for reinstallation. Safety notices recommend keeping parts clean and containing fluids during maintenance.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...f8usejkddmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and reinstalling components while taking precautions to prevent contamination.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...udjkdksmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...udjkdksmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting fuel lines, removing mounting hardware, and capturing component details for reinstallation. Safety notices emphasize keeping parts clean and containing fluids during maintenance.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...udjkdksmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
Caterpillar Cat 301.5, 301.6 and 301.8 Mini Hydraulic Excavator (Prefix BFA) ...tengtui535
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5, 301.6 and 301.8 Mini Hydraulic Excavator (Prefix BFA) ...gongfuao7509
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...idksmmdmdm
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...jkdkkdsmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...jkdkkdsmmd
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...ufuejkdkmdm
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...ufuejkdkmdm
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
Caterpillar Cat 301.8 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...ufuejkdkmdm
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.5 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...vvnj41316031
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix BFA) Service Repair Ma...vvnj41316031
The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components such as lines, solenoids, pumps, manifolds, and gaskets. Instructions are provided for cleaning parts and surfaces, installing new gaskets or seals, and reconnecting or reinstalling the components in the reverse order of removal while following torque specifications. Cautions are given to contain fluids and avoid contaminating parts.
Similar to Caterpillar cat 301.8 mini hydraulic excavator (prefix bfa) service repair manual (bfa00001 and up) (20)
This manual covers service procedures for Toyota forklifts with pneumatic and cushion tires. It details removal and installation procedures, inspection methods, and adjustments for various components. Reference manuals are also listed for engines and other relevant components. The manual provides specifications, torque values, and other technical information needed for repair and maintenance of these vehicles.
This document provides an overview of servicing procedures for a Toyota forklift transmission. It includes sections on removal and installation of the torque converter and transmission assembly, disassembly and inspection of the torque converter, and disassembly of the transmission assembly. Procedures are outlined in steps and key points are called out, such as match marking parts during removal and selection of spacer thickness. Standard torque specifications are provided throughout.
This manual covers service procedures for Toyota forklifts with pneumatic and cushion tires. It details removal and installation procedures, inspection methods, and adjustments for various components. Reference manuals are also listed for engine repair. The manual sections include general information, the engine, transmission, axles, steering, brakes, mast, hydraulic systems and more.
This manual covers service procedures for Toyota forklifts with pneumatic and cushion tires. It details removal and installation procedures, inspection methods, and adjustments for various components. Reference manuals are also listed for engine repair. The manual sections include general information, the engine, transmission, axles, steering, brakes, mast, hydraulic systems and more.
This manual covers service procedures for Toyota forklifts with pneumatic and cushion tires. It details removal and installation procedures, inspection methods, and adjustments for various components. Reference manuals are also listed for engines and other relevant components. The manual provides specifications, torque values, and other technical information needed for repair and maintenance of these vehicles.
This manual covers service procedures for Toyota forklifts with pneumatic and cushion tires. It details removal and installation procedures, inspection methods, and adjustments for various components. Reference manuals are also listed for engine repair. The manual sections include general information, the engine, transmission, axles, steering, brakes, mast, hydraulic systems and more.
This manual covers service procedures for Toyota forklifts with pneumatic and cushion tires. It details removal and installation procedures, inspection methods, and adjustments for various components. Reference manuals are also listed for engines and other relevant components. The manual provides specifications, torque values, and other technical information needed for repair and maintenance of these vehicles.
1. This manual covers service procedures for Toyota forklifts including engine, transmission, steering, and brake systems.
2. It provides illustrations and descriptions to guide technicians through removal, inspection, and reinstallation of components.
3. The manual also includes specifications, torque values, and periodic maintenance schedules.
Massey ferguson mf165 tractors parts catalogue manualfujsjefjkskfmsme
This document provides part numbers and descriptions for components related to engines, electrical equipment, alternators, generators, and starters for Massey Ferguson tractors models MF 165, 168, 185, and 188. It includes 42 items that make up the engine installation for these tractor models, with part numbers, quantities, descriptions and comments for each item. It also provides similar listings for the electrical equipment, alternator, generator, and starter for the tractors.
Massey ferguson mf158 tractor parts catalogue manualfujsjefjkskfmsme
This document provides a parts list and diagrams for the engine and various electrical components of Massey Ferguson 155/158 tractors. It includes over 30 items related to the engine with part numbers and descriptions. The alternator, generator, starter motor and electrical equipment sections list additional parts with numbers and comments. Diagrams show the layout and connections of components on the engine and relevant systems.
Massey ferguson mf155 tractor parts catalogue manualfujsjefjkskfmsme
This document provides a parts list and diagrams for the engine and various electrical components of Massey Ferguson 155/158 tractors. It includes over 30 items related to the engine with part numbers and descriptions. The alternator, generator, starter motor and other electrical equipment are also detailed with multiple parts listed for each component. Diagrams show the layout and connections of systems on the tractor.
Massey ferguson mf140 tractor parts catalogue manualfujsjefjkskfmsme
This document contains parts lists and descriptions for engines, starters, generators, and other accessories for Massey Ferguson 133, 135, and 140 tractors. It includes over 30 parts with descriptions and part numbers. Notes provide additional details about the parts and which tractor models or engine types they are for.
Massey ferguson mf135 tractor parts catalogue manualfujsjefjkskfmsme
This document contains parts lists and descriptions for engines, starters, generators, and other accessories for Massey Ferguson 133, 135, and 140 tractors. It includes over 30 parts with descriptions and part numbers. Notes provide additional details about the parts and which tractor models or engine types they are for.
Massey ferguson mf133 tractor parts catalogue manualfujsjefjkskfmsme
This document contains parts lists and descriptions for engines, starters, generators, and other accessories for Massey Ferguson 133, 135, and 140 tractors. It includes over 30 parts with descriptions and part numbers. Notes provide additional details on the parts and which tractor models or engine types they are for.
Massey ferguson mf super 90 tractor parts catalogue manualfujsjefjkskfmsme
This document contains a parts list for a Massey Ferguson MF Super 90 tractor engine. It includes 38 items categorized as engine gasket sets for both gas and LP fuel types. The gasket sets include various cylinder head, block, valve cover, and crankcase gaskets and seals to replace worn parts and ensure proper sealing when servicing the engine.
Massey ferguson mf 6713 r tractor (eco4 tier 2 3 ; br) parts catalogue manualfujsjefjkskfmsme
This document contains a table of contents and parts list for an MF 6713R tractor engine. The table of contents lists 19 sections that cover various engine and tractor systems. The parts lists include over 30 individual parts for assemblies like the cylinder block, crankshaft, camshaft, cylinder head, intake manifold, and turbocharger.
Massey ferguson mf 5608 tractor (c339061 h349047) parts catalogue manualfujsjefjkskfmsme
The document provides a parts list and technical specifications for the timing gear housing of a Massey Ferguson MF 5608 tractor. It includes 27 items such as the timing gear case, idler gear, crankshaft seal, various screws and pins. Notes indicate applicability based on serial number and whether items are included in a gasket set. The list is intended to support maintenance and repair of the timing gear housing component.
Massey ferguson mf 3455 cm crawler type tractor parts catalogue manualfujsjefjkskfmsme
This document provides part numbers and descriptions for components of a Massey Ferguson MF 3455 C/CF/CM crawler-type tractor engine. It includes listings for the engine assembly, short engine, cylinder block, camshaft, pistons and connecting rods, end cover, cylinder head, rocker shaft, and fuel injection equipment. The listings provide item numbers, part numbers, quantities, descriptions, and in some cases additional details like replacement information.
This document provides part numbers and descriptions for components of a Massey Ferguson MF 3455 C/CF/CFM crawler tractor engine. It includes listings of parts for the engine assembly, short engine, cylinder block, camshaft, pistons/connecting rods, end cover, cylinder head, and rocker shaft. Each item lists the part number, quantity, description, and notes whether it is a component of a larger assembly.
Massey ferguson mf 3455 cf crawler type tractor parts catalogue manualfujsjefjkskfmsme
This document provides part numbers and descriptions for components of a Massey Ferguson MF 3455 C/CF/CM crawler-type tractor engine. It includes listings for the engine assembly, short engine, cylinder block, camshaft, pistons and connecting rods, end cover, cylinder head, rocker shaft, and fuel injection equipment. The listings provide item numbers, part numbers, quantities, descriptions, and in some cases additional details like replacement information.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i01112109
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00587462
1. Disconnect fuel injection lines (1) from fuel injection nozzles (2) .
NOTICE
Do not let the tops of fuel nozzles turn when the fuel line nuts are
loosened or tightened.
The nozzles will be damaged if the top of the nozzle turns in the body.
The engine will be damaged if a defective fuel injection nozzle is used
because the shape of fuel (spray pattern) that comes out of the nozzles
will not be correct.
2. Disconnect fuel injection lines (1) from fuel injection pump (3). Cap all openings or plug all
openings immediately.
3. Remove fuel injection lines (1) from the engine as a unit.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00587462
1. Install fuel injection lines (1) on the engine as a unit.
NOTICE
Do not let the tops of fuel nozzles turn when the fuel line nuts are
loosened or tightened.
The nozzles will be damaged if the top of the nozzle turns in the body.
The engine will be damaged if a defective fuel injection nozzle is used
because the shape of fuel (spray pattern) that comes out of the nozzles
will not be correct.
2. Connect fuel injection lines (1) to fuel injection pump (3). Tighten the fuel injection line
nuts to the following torque:
3003 Engine ... 22 N·m (16 lb ft)
3013, 3014, and 3024 Engines ... 20 N·m (15 lb ft)
3. Connect fuel injection lines (1) to fuel injection nozzles (2). Tighten the fuel injection line
nuts to the following torque:
3003 Engine ... 22 N·m (16 lb ft)
3013, 3014, and 3024 Engines ... 20 N·m (15 lb ft)
4. Prime the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime" for more
information.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:09:49 UTC+0800 2020
3/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i01428959
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Disconnect all electrical connections to the fuel shutoff solenoid before proceeding.
Mark all connections for later installation.
1/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 1 g00592462
1. Remove fuel shutoff solenoid (1) from the governor by rotating fuel shutoff solenoid (1) in
a counterclockwise direction.
2. Remove the O-ring seal from fuel shutoff solenoid (1). Inspect the O-ring seal for wear or
for damage. If the O-ring seal is worn or damaged, use a new part for replacement.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00592462
1. Install the O-ring seal onto fuel shutoff solenoid (1) .
2/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 2. Install fuel shutoff solenoid (1) in the governor by rotating fuel shutoff solenoid (1) in a
clockwise direction. Tighten fuel shutoff solenoid (1) to a torque of 17 N·m (12 lb ft).
Note: Reconnect all electrical connections to the fuel shutoff solenoid before you operate
the engine.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:10:46 UTC+0800 2020
3/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i04583132
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
B. If necessary, remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel
Shutoff Solenoid - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00825132
Illustration 2 g00825137
1. Remove bolts (4) and nuts (2) that fasten the fuel injection pump to the cylinder block.
2. Carefully raise fuel injection pump (1) from the cylinder block and remove clip (7) that
connects link (6) to fuel rack control (5) .
2/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 3. Remove fuel injection pump (1) from the cylinder block.
Note: Record the thickness of each shim and the number of shims for reassembly. The fuel
injection timing is determined by the shim pack thickness that is between the fuel injection
pump and the mounting face on the cylinder block. For more information on the fuel
injection pump, refer to Specifications, "Fuel Injection Pump".
4. Remove shims (3) from the mounting plate.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:11:43 UTC+0800 2020
3/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i01591134
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 1 g00825132
1. Position the correct number of shims (3) on the mounting face of the cylinder block. Refer
to Specifications, "Fuel Injection Pump".
Illustration 2 g00825137
2. Position fuel injection pump (1) close to the mounting face of the cylinder block, and
connect link (6) and fuel rack control (5) with clip (7) .
3. Put fuel injection pump (1) in position on the mounting face of the cylinder block.
4. Install bolts (4) and nuts (2) that fasten the fuel injection pump to the cylinder block.
Tighten bolts (4) and nuts (2) to the following torque.
2/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. 3003 Engine ... 6 N·m (4 lb ft)
3013, 3014, and 3024 Engines ... 15 N·m (11 lb ft)
3024C Engine ... 15 N·m (11 lb ft)
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
b. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:12:39 UTC+0800 2020
3/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i01893805
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 1 g00825291
Typical example
1. Remove exhaust manifold nuts (5) and bolts (6) .
2. Remove exhaust manifold (4) from the cylinder head (1) .
3. Remove gasket (3) from the cylinder head.
4. Remove any remaining gasket material and carbon from the cylinder head and the exhaust
manifold. Be careful not to damage the mating surface on the cylinder head for the exhaust
manifold.
5. Remove studs (2) for exhaust manifold (4) from cylinder head (1) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00825291
Typical example
2/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 1. If studs (2) were removed during disassembly, install attaching studs (2) to cylinder head
(1) .
2. Put a new exhaust manifold gasket (3) in position on cylinder head (1) .
Note: Do not use any sealant on the exhaust manifold gasket.
3. Put exhaust manifold (4) in position on cylinder head (1) .
4. Install exhaust manifold nuts (5) and bolts (6) .
For 3013C Engines and 3024C Engines, tighten nuts (5) and bolts (6) to a torque of 25 N·m
(18 lb ft).
For 3011C Engines, tighten nuts (5) and bolts (6) to a torque of 10 N·m (89 lb in).
Note: Tighten the two inner bolts first on three cylinder engines. Tighten the four inner
bolts first on four cylinder engines. Then tighten the two outer bolts and the two nuts.
Ensure that the bolts with different lengths are installed in the correct holes.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:13:36 UTC+0800 2020
3/3301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i02399171
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
Start By:
A. Remove the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Before you begin the removal of the valve springs, refer to Specifications, "Cylinder Head
Valves" and Testing and Adjusting, "Cylinder Head - Inspect" for appropriate information on the
valve springs.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
1/4301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. 1. Ensure that the piston is at the top center position.
Illustration 1 g00825744
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. Use Tooling (A) to compress valve springs (1) . Remove valve keepers (2) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
3. Release the pressure on Tooling (A) . Remove valve spring retainer (3) and valve springs
(1) from the cylinder head.
2/4301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. NOTICE
Do not turn the crankshaft while the valve springs are removed.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00825744
3/4301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Place new valve springs (1) into position on the cylinder head.
Note: Ensure that the closed damper coils are toward the cylinder head if double valve
springs are used.
2. Install valve spring retainer (3) .
3. Use Tooling (A) to compress valve springs (1) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
4. Install valve keepers (2) in order to lock the valve springs in position.
5. Release the pressure slowly on Tooling (A) . Remove Tooling (A) . Strike the top of the
valves with a soft faced hammer in order to ensure that the valve keepers are properly
installed.
End By: Install the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:14:33 UTC+0800 2020
4/4301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i02015360
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the bottom face of the cylinder head. Use a dial indicator to check the depth of the
valves below the face of the cylinder head before the valve springs are removed. Refer to
the Specifications, "Cylinder Head Valves" for the correct dimensions.
2. Place an index mark on the heads of the inlet valves and the exhaust valves for installation
purposes.
1/6301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...