The document provides instructions for removing and installing a flywheel on a Caterpillar C3.3B engine. It lists the required tools which include guide studs and a link bracket. The removal procedure involves removing bolts from the flywheel, installing guide studs into the crankshaft, and using a lifting device to remove the flywheel. Instructions are given to inspect the flywheel and ring gear upon removal and replace any worn or damaged components.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...fjjskekskem
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader with a C3.3B engine, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, removing springs and other parts, checking for wear and damage, and installing components in reverse order. Safety precautions are provided regarding contained fluids and sudden spring release.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...fujsjefskekfksem
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts/screws, removing parts, installing replacement parts in the reverse order, and noting important safety information and checks to perform. Torque specifications are provided where relevant.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...fhshefjjskefkem
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader with a C3.3B engine, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, removing parts, inspecting components for wear or damage, and installing parts in the reverse order of removal while applying grease or installing new gaskets as specified. Safety notices are included to contain fluids and wear protective equipment.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...ujfjdkkmsme
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader with a C3.3B engine, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, removing springs and other parts, checking for wear and damage, and installing components in reverse order. Safety precautions are provided regarding contained fluids and sudden spring release.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...ufjjjskkmsmed
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader with a C3.3B engine, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, removing parts, inspecting components, and installing parts in the reverse order of removal while following safety precautions. Torque specifications and required tools are provided where needed.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...tengtui535
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening specific bolts and components in a numbered list. Safety precautions are provided, and technicians are instructed to clean parts and replace any that show wear or damage. Torque specifications are given for reinstallation.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...f8usejkdmmd8i
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal requires removing screws and covers. Installation includes cleaning, inspecting clearances, reinstalling covers with screws.
- Water pump - Removal requires removing belts, bolts, and pulley. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal requires draining coolant, disconnecting hoses, and removing bolts and gasket. Installation is the reverse
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...f8seodkdmdmed3
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening specific bolts and components in a certain sequence. Safety precautions are provided to contain fluids and wear protective equipment. Installation is the reverse of removal, and components should be clean and free of damage.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...fjjskekskem
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader with a C3.3B engine, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, removing springs and other parts, checking for wear and damage, and installing components in reverse order. Safety precautions are provided regarding contained fluids and sudden spring release.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...fujsjefskekfksem
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts/screws, removing parts, installing replacement parts in the reverse order, and noting important safety information and checks to perform. Torque specifications are provided where relevant.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...fhshefjjskefkem
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader with a C3.3B engine, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, removing parts, inspecting components for wear or damage, and installing parts in the reverse order of removal while applying grease or installing new gaskets as specified. Safety notices are included to contain fluids and wear protective equipment.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...ujfjdkkmsme
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader with a C3.3B engine, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, removing springs and other parts, checking for wear and damage, and installing components in reverse order. Safety precautions are provided regarding contained fluids and sudden spring release.
Caterpillar cat 279 d compact track loader (prefix rcx) service repair manual...ufjjjskkmsmed
This document provides instructions for removing and installing various engine components on a 279D Compact Track Loader with a C3.3B engine, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, removing parts, inspecting components, and installing parts in the reverse order of removal while following safety precautions. Torque specifications and required tools are provided where needed.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...tengtui535
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening specific bolts and components in a numbered list. Safety precautions are provided, and technicians are instructed to clean parts and replace any that show wear or damage. Torque specifications are given for reinstallation.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...f8usejkdmmd8i
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal requires removing screws and covers. Installation includes cleaning, inspecting clearances, reinstalling covers with screws.
- Water pump - Removal requires removing belts, bolts, and pulley. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal requires draining coolant, disconnecting hoses, and removing bolts and gasket. Installation is the reverse
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...f8seodkdmdmed3
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening specific bolts and components in a certain sequence. Safety precautions are provided to contain fluids and wear protective equipment. Installation is the reverse of removal, and components should be clean and free of damage.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...ze6074xunong
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...f8usejkddmmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...fjskemmd4r
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Loosen plug and carefully remove cap to release spring force and remove parts. Install in reverse order.
- Engine oil pump - Remove screws and covers to access rotors. Inspect for wear and install ensuring proper clearance.
- Water pump - Remove bolts to access pump. Inspect gasket and install new one when reinstalling pump.
- Water temperature regulator - Disconnect hose and remove bolts/gasket to access regulator. Check operation on installation.
- Flywheel - Loosen bolts in specific pattern and remove using puller. Clean
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - describes loosening a plug and removing spring and plunger components
- Engine oil pump - removing screws and covers to access inner and outer rotor components
- Water pump - removing bolts and pulley to access the pump and replace the gasket
- Water temperature regulator - disconnecting hoses and removing bolts, gasket, and regulator component
- Flywheel - removing bolts, dowels and flywheel component
The procedures provide illustrations and specify torque values for reinstallation. Safety and cleaning notes are included.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...f8usjejkdmmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening specific bolts and components in a certain sequence. Safety precautions are provided to contain fluids and wear protective equipment. Installation is the reverse of removal, and components should be clean and free of damage.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...fujskdiddkmdm3e
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...gen78guozun
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...xiapokang564341
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, plugs, and other fasteners to access the components. Safety precautions and required tools are noted. Installation is the reverse of the removal process.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...hvy7sbkw8e
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing components like caps, covers, rotors, pumps, regulators and flywheels. Special tools may be required and safety precautions are noted. Reinstallation is the reverse of removal, with cleaning, inspection and replacement of damaged or worn parts as needed. Torque specifications are provided where applicable.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...wenxian17880
The document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- The engine oil relief valve, which involves loosening a plug and carefully removing a cap to release spring force.
- The engine oil pump, which requires removing screws and covers to access the inner and outer rotors.
- The water pump, which is removed by taking off bolts and pulley, and installing a new gasket.
- The water temperature regulator, which is accessed by disconnecting hoses and removing bolts and gaskets.
Caterpillar cat 257 d multi terrain loader (prefix fmr) service repair manual...ujfjjsjekkmsmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including the engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures describe removing parts, inspecting and cleaning components, and installing parts in the reverse order of removal while following safety precautions and using the appropriate tools. Torque specifications are provided where relevant.
Caterpillar cat 257 d multi terrain loader (prefix fmr) service repair manual...ujfdjdjfkjksk
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including the engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures describe removing parts, inspecting and cleaning components, and installing parts in the reverse order of removal while following safety precautions and using the appropriate tools. Torque specifications are provided where relevant.
Caterpillar cat 257 d multi terrain loader (prefix fmr) service repair manual...fjsjefskekfmme
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including the engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures describe removing parts, inspecting and cleaning components, and installing following the reverse order of removal while applying lubricants and torques as specified. Safety notices are included to wear protective equipment and contain fluids.
Caterpillar cat 257 d multi terrain loader (prefix fmr) service repair manual...fjjskekfsem
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Removing and installing the engine oil relief valve
- Removing and installing the engine oil pump
- Removing and installing the water pump
- Removing and installing the water temperature regulator
- Removing and installing the flywheel
The procedures provide detailed steps for each job, including necessary tools and torque specifications. Safety notices are included to warn technicians of potential hazards.
The document provides instructions for removing and installing the lifter group on a C2.2 engine. The removal process involves draining coolant, loosening bolts in a specific sequence, and removing the cylinder head. Dowel pins must be inspected and new gaskets installed. When installing, the cylinder head is positioned with guide bolts and tightened in a numerical sequence using a torque wrench and degree wheel. Hoses are then reconnected.
The document provides instructions for removing and installing the lifter group on a C2.2 engine. The removal process involves draining coolant, loosening and removing bolts, and lifting off the cylinder head. When installing, the instructions specify cleaning surfaces, installing dowels and a new gasket, tightening bolts in a specific sequence, and reinstalling other components. Tools include feeler gauges, guide bolts, and a degree wheel for proper installation of the cylinder head and lifter group.
The document provides instructions for removing and installing the lifter group on a C2.2 engine. The removal process involves draining coolant, loosening and removing bolts, and lifting off the cylinder head. When installing, the instructions specify cleaning surfaces, installing dowels and a new gasket, tightening bolts in a specific sequence, and reinstalling other components. Tools include feeler gauges, guide bolts, and a degree wheel for tightening bolts to the specified torque and angle.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...gongfuao7509
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into the motor housing in the specified order.
3. Attaching lifting brackets and safely lifting the heavy swing motor or drive components during removal and installation procedures.
Caterpillar Cat 329D and 329D L Excavator (Prefix DTZ) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
More Related Content
Similar to Caterpillar Cat 279D COMPACT TRACK LOADER (Prefix RCX) Service Repair Manual Instant Download.pdf
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...ze6074xunong
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...f8usejkddmmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...fjskemmd4r
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Loosen plug and carefully remove cap to release spring force and remove parts. Install in reverse order.
- Engine oil pump - Remove screws and covers to access rotors. Inspect for wear and install ensuring proper clearance.
- Water pump - Remove bolts to access pump. Inspect gasket and install new one when reinstalling pump.
- Water temperature regulator - Disconnect hose and remove bolts/gasket to access regulator. Check operation on installation.
- Flywheel - Loosen bolts in specific pattern and remove using puller. Clean
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - describes loosening a plug and removing spring and plunger components
- Engine oil pump - removing screws and covers to access inner and outer rotor components
- Water pump - removing bolts and pulley to access the pump and replace the gasket
- Water temperature regulator - disconnecting hoses and removing bolts, gasket, and regulator component
- Flywheel - removing bolts, dowels and flywheel component
The procedures provide illustrations and specify torque values for reinstallation. Safety and cleaning notes are included.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...f8usjejkdmmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening specific bolts and components in a certain sequence. Safety precautions are provided to contain fluids and wear protective equipment. Installation is the reverse of removal, and components should be clean and free of damage.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...fujskdiddkmdm3e
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...gen78guozun
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...xiapokang564341
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing and loosening bolts, plugs, and other fasteners to access the components. Safety precautions and required tools are noted. Installation is the reverse of the removal process.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...hvy7sbkw8e
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve
- Engine oil pump
- Water pump
- Water temperature regulator
- Flywheel
The procedures describe removing components like caps, covers, rotors, pumps, regulators and flywheels. Special tools may be required and safety precautions are noted. Reinstallation is the reverse of removal, with cleaning, inspection and replacement of damaged or worn parts as needed. Torque specifications are provided where applicable.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...wenxian17880
The document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- The engine oil relief valve, which involves loosening a plug and carefully removing a cap to release spring force.
- The engine oil pump, which requires removing screws and covers to access the inner and outer rotors.
- The water pump, which is removed by taking off bolts and pulley, and installing a new gasket.
- The water temperature regulator, which is accessed by disconnecting hoses and removing bolts and gaskets.
Caterpillar cat 257 d multi terrain loader (prefix fmr) service repair manual...ujfjjsjekkmsmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including the engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures describe removing parts, inspecting and cleaning components, and installing parts in the reverse order of removal while following safety precautions and using the appropriate tools. Torque specifications are provided where relevant.
Caterpillar cat 257 d multi terrain loader (prefix fmr) service repair manual...ujfdjdjfkjksk
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including the engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures describe removing parts, inspecting and cleaning components, and installing parts in the reverse order of removal while following safety precautions and using the appropriate tools. Torque specifications are provided where relevant.
Caterpillar cat 257 d multi terrain loader (prefix fmr) service repair manual...fjsjefskekfmme
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including the engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures describe removing parts, inspecting and cleaning components, and installing following the reverse order of removal while applying lubricants and torques as specified. Safety notices are included to wear protective equipment and contain fluids.
Caterpillar cat 257 d multi terrain loader (prefix fmr) service repair manual...fjjskekfsem
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Removing and installing the engine oil relief valve
- Removing and installing the engine oil pump
- Removing and installing the water pump
- Removing and installing the water temperature regulator
- Removing and installing the flywheel
The procedures provide detailed steps for each job, including necessary tools and torque specifications. Safety notices are included to warn technicians of potential hazards.
The document provides instructions for removing and installing the lifter group on a C2.2 engine. The removal process involves draining coolant, loosening bolts in a specific sequence, and removing the cylinder head. Dowel pins must be inspected and new gaskets installed. When installing, the cylinder head is positioned with guide bolts and tightened in a numerical sequence using a torque wrench and degree wheel. Hoses are then reconnected.
The document provides instructions for removing and installing the lifter group on a C2.2 engine. The removal process involves draining coolant, loosening and removing bolts, and lifting off the cylinder head. When installing, the instructions specify cleaning surfaces, installing dowels and a new gasket, tightening bolts in a specific sequence, and reinstalling other components. Tools include feeler gauges, guide bolts, and a degree wheel for proper installation of the cylinder head and lifter group.
The document provides instructions for removing and installing the lifter group on a C2.2 engine. The removal process involves draining coolant, loosening and removing bolts, and lifting off the cylinder head. When installing, the instructions specify cleaning surfaces, installing dowels and a new gasket, tightening bolts in a specific sequence, and reinstalling other components. Tools include feeler gauges, guide bolts, and a degree wheel for tightening bolts to the specified torque and angle.
Similar to Caterpillar Cat 279D COMPACT TRACK LOADER (Prefix RCX) Service Repair Manual Instant Download.pdf (17)
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...gongfuao7509
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into the motor housing in the specified order.
3. Attaching lifting brackets and safely lifting the heavy swing motor or drive components during removal and installation procedures.
Caterpillar Cat 329D and 329D L Excavator (Prefix DTZ) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar Cat 324D FM LL EXCAVATOR (Prefix JLS) Service Repair Manual Insta...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 324D FM LL EXCAVATOR. It outlines 21 steps for disassembly, which include removing plates, springs, pistons, gears, and other components. It also outlines 16 steps for assembly, which include installing bearings, seals, gears, and other components back into the final drive housing using various tools. The document includes illustrations to supplement the written instructions.
Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Man...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It lists 30 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps to reassemble the final drive by installing components like bearings, seals, gears, and shims in the reverse order of disassembly. Precise tools and procedures are required due to the heavy weight and precision fitting of components.
Caterpillar Cat 323D2 and 323D2 L Excavator (Prefix JEX) Service Repair Manua...gongfuao7509
The document provides instructions for disassembling the final drive of an excavator model 323D2. It involves 33 steps including removing the final drive cover, carrier assembly, ring gears, and other components. Various tools are required including a transmission repair stand, link brackets, forcing screws, and puller assembly. Cleanliness is important to prevent dirt from entering internal parts during disassembly.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual Instant ...gongfuao7509
The document provides instructions for removing the engine oil filter base from a 322C FM excavator with a 3126 engine. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the oil filter base mounting surface before installing the new oil filter base. The summary is provided in 3 sentences or less as requested.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual Instant ...gongfuao7509
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse of removal.
3. Turbocharger removal requires removing bolts and nuts connecting it to the exhaust manifold and disconnecting oil lines. Disassembly separates the housing components. Assembly reconnects the parts and installation bolts the turbocharger back into place.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual Instant ...gongfuao7509
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, replacing seals, and using tools to install the governor along with associated lines, pins, and clips. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 1YS) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the governor and associated components on a Caterpillar 3116 engine. The removal process involves disconnecting linkages and tubes, removing mounting bolts and clips, and using specialized tools. The installation follows the removal steps in reverse, applying lubricant to seals and ensuring proper adjustment of linkages. Required tools include various pliers and pin tools to facilitate disconnecting and reconnecting components.
Caterpillar Cat 322 L EXCAVATOR (Prefix 9RL) Service Repair Manual Instant Do...gongfuao7509
This document provides instructions for removing and installing a governor from a Caterpillar Cat 322 L excavator powered by a 3116 engine. The removal procedure involves disconnecting tubes, removing clips and bolts, and using special tools. The installation procedure describes cleaning and lubricating parts, replacing seals, and using tools to install the governor components in reverse order of removal. Proper torque specifications and checks are listed to ensure correct installation.
This document provides instructions for servicing the air conditioning system on Caterpillar 322 and 322L excavators. It describes safety precautions when working with refrigerant due to risks of injury. The document outlines procedures for preparing the machine, removing and installing various AC system components like lines, the compressor, and preparing the system for disassembly and reassembly. Detailed steps are provided for correctly assembling refrigerant line fittings and other components.
Caterpillar Cat 320F L Excavator (Prefix YBM) Service Repair Manual Instant D...gongfuao7509
The document provides instructions for removing and installing a boom cylinder on an excavator. Key steps include:
1. Lowering the boom and releasing hydraulic pressure before removal.
2. Detaching hoses and removing bolts and pins to separate the cylinder from the excavator.
3. Lifting the cylinder, which weighs approximately 287kg, off the excavator using slings.
4. Reinstalling involves lifting the cylinder back into place with slings, reattaching with bolts and pins, and reconnecting hoses. Torque specifications are provided for all fasteners.
This document provides instructions for removing and installing a flywheel on a 320E LRR excavator with a C6.6 engine. The removal procedure involves using guide studs and lifting equipment to support the flywheel, then removing mounting bolts. The installation procedure specifies cleaning and inspecting components, positioning the flywheel with guide studs and lifting equipment, and tightening mounting bolts to the specified torque. Instructions are also provided for removing and installing a crankshaft rear seal.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for performing maintenance on the engine's crankshaft pulley, vibration damper, front seal, and front cover. Precautions are provided to keep parts clean and torque specifications are given.
This document provides instructions for disassembling and assembling the gear pump (pilot) and main hydraulic pump on a Caterpillar 320D2 excavator. The summary includes steps to disassemble the gear pump by removing housing bolts, seals, gears, and plates. It also describes removing the main hydraulic pump by disconnecting hoses and harnesses, removing mounting bolts, and lifting out the pump along with attached auxiliary pumps and pilots.
The document provides instructions for disassembling and assembling the travel motor of a 320D2L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, check valves, fittings, pistons, plates, seals and more. It then describes 25 steps to reassemble the travel motor, replacing components in the reverse order and ensuring proper alignment of parts like keys and cam plates. Special care must be taken to avoid damaging parts and keep components matched during assembly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 279D COMPACT TRACK LOADER RCX
Configuration: 279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242518
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
Illustration 1 g02788578
Illustration 2 g02788541
1/2
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Loosen plug (1). Carefully remove cap (1) from the front housing cover.
Note: The spring force will be released when the cap is removed.
2. Remove plug (1), washer (2), spring (3), and plunger (4) from the bore for the relief valve in
the front housing cover.
Installation Procedure
1. Install engine oil relief valve (1) in the reverse order of removal.
a. Install plug (1) and tighten plug (1) to a torque of 69 to 78 N·m (51 to 57 lb ft).
Note: Ensure that the spring is properly located inside the plunger and the cap.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 29 22:47:54 UTC+0800 2019
2/2
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 279D COMPACT TRACK LOADER RCX
Configuration: 279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242520
Engine Oil Pump - Remove and Install
SMCS - 1304-010
Removal Procedure
Start By:
a. Remove the front housing.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/4
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g02788686
1. Remove screws (2) and cover (1).
Illustration 2 g02788689
2. Remove inner rotor (4) from outer rotor (3).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 129-1967 White Grease 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. NOTICE
If any part of the engine oil pump is worn or damaged, the complete
assembly of the engine oil pump must be replaced.
1. Ensure that all components of the engine oil pump are clean and free from wear and
damage.
Illustration 3 g02788689
2. Position outer rotor (3) into the pump body. Check the clearance between outer rotor (3) and
the pump body.
3. Install inner rotor (4) into outer rotor (3). Check the clearance between the lobes of outer
rotor (3) and inner rotor (4).
Illustration 4 g02788686
4. Position a strip of Plastigage onto the outer rotor face with Tooling (A). Position cover (1)
and install screws (2) and torque. Remove cover (1) and check clearance between the rotor
and cover (1).
5. Position cover (1) and install screws (2). Tighten screws (2) to a torque of 8 to 9 N·m
(70 to 83 lb in).
3/4
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. End By:
a. Install the front housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 29 22:48:53 UTC+0800 2019
4/4
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 279D COMPACT TRACK LOADER RCX
Configuration: 279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242522
Water Pump - Remove and Install
SMCS - 1361-011; 1361-012
Removal Procedure
Start By:
a. Remove the v-belts.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1. Refer to Operation and Maintenance Manual, "Coolant - Change" for the proper draining
and filling procedures.
Illustration 1 g02794283
2. Remove bolts (2) and remove pulley (1).
1/2
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g02794286
3. Remove bolts (4).
4. Remove water pump (3) and discard the gasket. Install a new gasket upon installation.
Installation Procedure
1. Install water pump (3) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 29 22:49:52 UTC+0800 2019
2/2
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 279D COMPACT TRACK LOADER RCX
Configuration: 279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242525
Water Temperature Regulator - Remove and Install - C3.3B
SMCS - 1355-010
S/N - A9W1-UP
S/N - A9Z1-UP
S/N - AJ71-UP
S/N - CE21-UP
S/N - DML1-UP
S/N - EML1-UP
S/N - F8C1-UP
S/N - FMR1-UP
S/N - FTK1-UP
S/N - GBJ1-UP
S/N - GTK1-UP
S/N - HAM1-UP
S/N - HEL1-UP
S/N - HMR1-UP
S/N - JBE1-UP
S/N - JRD1-UP
1/4
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. S/N - JRF1-UP
S/N - JRS1-UP
S/N - JSL1-UP
S/N - JSN1-UP
S/N - KTS1-UP
S/N - L661-UP
S/N - L771-UP
S/N - L881-UP
S/N - LST1-UP
S/N - MLT1-UP
S/N - MPW1-UP
S/N - NTL1-UP
S/N - PPT1-UP
S/N - RCX1-UP
S/N - SEN1-UP
S/N - STK1-UP
S/N - TAZ1-UP
S/N - TLK1-UP
S/N - WCT1-UP
Removal Procedure
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
2/4
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Dispose of all fluids according to local regulations and mandates.
1. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the
correct draining procedure.
Note: Coolant only needs drained to below the water temperature regulator.
Illustration 1 g02794379
2. Disconnect hose assembly (1).
3. Remove bolts (2) from the water temperature regulator housing . Remove water temperature
regulator elbow (3).
Illustration 2 g02794381
3/4
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g02794385
4. Remove gasket (5) and remove water temperature regulator (4) from the water temperature
regulator housing.
Note: Note the orientation of the water temperature regulator elbow.
Installation Procedure
1. Install water temperature regulator (4) in the reverse order of removal.
a. Check the water temperature regulator for correct operation. Refer to System
Operation, Testing and Adjusting, "Water Temperature Regulator - Test" for the
correct procedure to test the water temperature regulator. If any components of the
water temperature regulator housing are worn or damaged, the complete assembly
must be replaced.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 29 22:50:52 UTC+0800 2019
4/4
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02794543
1. Remove two bolts (2) from flywheel (1).
Illustration 2 g02798921
2. Install Tooling (A) into the crankshaft.
3. Install Tooling (B) and a suitable lifting device on flywheel (1). The weight of flywheel (1)
is approximately 30 kg (66 lb).
4. Remove remaining bolts (2).
5. Remove flywheel (1) from the cylinder block.
3/6
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g02798923
6. Inspect flywheel (1) and the ring gear (3) for wear and damage. Replace any worn
components or damaged components.
7. If necessary, remove the flywheel ring gear (3), follow Step 7.a through Step 7.b.
a. Place the flywheel assembly on a suitable support.
b. Use a hammer and a punch in order to remove ring gear (3) from flywheel (1). If
necessary, a torch may be needed to heat ring gear (3).
Note: Identify the orientation of the teeth on the flywheel ring gear (3).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M12 - 1.25 by 100 mm
2
B 138-7573 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
4/6
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g02798923
Always wear protective gloves when handling parts that have been
heated.
1. If flywheel ring gear (3) was removed, follow Step 1.a through Step 1.c in order to install
ring gear (3) to flywheel (1).
a. Identify the orientation of teeth on new ring gear (3).
Note: The chamfered side of ring gear teeth must face toward the starting motor when
the flywheel is installed. This position will ensure the correct engagement of the
starting motor.
b. Raise heat of flywheel ring gear (3) in an oven to a maximum temperature of 250 °C
(482 °F) prior to installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear
onto flywheel (1).
5/6
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 5 g02798921
2. Install Tooling (B) and a suitable lifting device on flywheel (1). The weight of flywheel (1)
is approximately 30 kg (66 lb).
3. Install Tooling (A) into the crankshaft.
4. Use the lifting device to position flywheel (1) onto Tooling (A).
5. Install bolts (2) to flywheel (1).
6. Remove Tooling (A).
Illustration 6 g02794543
7. Install remaining bolts (2) to flywheel (1). Apply engine oil to bolts. Tighten bolts (2) to a
torque of 98 to 107 N·m (72 to 80 lb ft).
8. Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further
information.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 29 22:51:51 UTC+0800 2019
6/6
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 279D COMPACT TRACK LOADER RCX
Configuration: 279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242540
Crankshaft Rear Seal and Wear Sleeve - Remove - Includes
Crankshaft Gear
SMCS - 1161-011; 7558-011
Removal Procedure
Start By:
a. Remove the flywheel.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Place the engine at top dead center.
1/2
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g02799897
2. Use a screw driver to remove rear seal (1).
Illustration 2 g02799899
3. Check the alignment of crankshaft gear (2) and camshaft gear (3). Remove crankshaft gear
(2) and ring seal.
Illustration 3 g02799901
4. Place crankshaft gear (2) with wear sleeve (4) in a suitable vice. Remove wear sleeve (4)
with a suitable chisel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 29 22:52:50 UTC+0800 2019
2/2
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 279D COMPACT TRACK LOADER RCX
Configuration: 279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242547
Crankshaft Rear Seal and Wear Sleeve - Install - Includes
Crankshaft Gear
SMCS - 1161-012; 7558-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1146 Crankshaft Rear Seal and Wear Sleeve Driver(1)
1
423-9665 Crank shaft Rear Seal and Wear Sleeve Driver(2)
1
(1)
Used for the C3.3B
(2)
Used for the C2.6
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1/2
279D Compact Track Loader RCX00001-UP (MACHINE) POWERED BY C3.3B En...
2019/10/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading