Caterpillar cat 247 b3 multi terrain loader (prefix esl) service repair manual (esl00001 and up)

Service Repair Manual
Models
247B3 MULTI TERRAIN LOADER

Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 247B3 MULTI TERRAIN LOADER ESL
Configuration: 247B3 Multi Terrain Loader ESL00001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
247B, 247B2, 257B and 257B2 Multi Terrain Loaders Power Train
Media Number -RENR4874-05 Publication Date -01/07/2018 Date Updated -11/07/2018
i02061094
Piston Motor (Hydrostatic) - Disassemble
SMCS - 5058-015-H7
S/N - ESL1-UP
S/N - KB31-UP
S/N - MTL1-5074
S/N - SLK1-7299
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
B 1U-7280 Pin Punch 1
C 1P-0510 Driver Gp 1
D 2P-8312 Retaining Ring Pliers 1
E 1U-7276 Pin Punch 1
F 8B-5144 Bolts (5/8 inch by 18 NF by 3 inch) 2
G 8H-0663 Bearing Puller 1
H 6V-5839 Washers 4
6V-8214 Bolts (6 mm by 1.00 NC by 20 mm) 4
9M-1974 Hard Washers 4
1/15247B3 Multi Terrain Loader ESL00001-UP (MACHINE) POWERED BY C2.2 Engin...
2019/11/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

9X-8267 Washers 4
Start By:
a. Remove track drive. Refer to Disassembly and Assembly, "Track Drive - Remove".
Note: The following procedure is intended for cleaning purposes only.
Illustration 1 g00882206
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Mark the piston motor for assembly purposes. Remove bolts (1). Remove cover (2).

2. Remove gasket (3).
3. Remove washer (4). Remove disc spring (5). Remove fitting (6).
4. Install Tooling (H). Use low pressure compressed air to remove piston (7).
Note: Low pressure air is required in order to allow the piston to release from the motor.
Note: Tooling (H) is required in order to prevent damage to the piston.

5. Remove seal (8) from piston (7).
6. Remove bolts (9). Remove brake housing (10).

7. Use Tooling (A) to remove seal (11) from brake housing (10).
8. Remove discs (12) from the outer spline. Remove discs (13) from the inner spline. Remove
shim (14). Remove O-ring seal (15).

Note: Observe the shaft's direction.
9. Remove shaft (16).
10. Remove fittings (19). Remove bolts (18). Remove rear case (17).

11. Use Tooling (B) to remove distributor (20) from rear case (17). Remove springs (21).
Remove pin (22). Remove O-ring seals (23).
12. Block distributor (20). Use Tooling (C) to remove bushing (24).

13. Remove O-ring seal (25). Remove O-ring seal (26). Remove O-ring seal (27).
14. Remove plug (28). Remove O-ring seal (29).

15. Remove plug (34). Remove O-ring seal (33). Remove spring (32).
16. Remove washer (31). Remove spool (30).
17. Remove plug (38). Remove O-ring seal (37). Remove spring (36).
18. Remove washer (35).

19. Remove cam ring (39).
20. Remove rotor (40). Remove O-ring seal (41).
10/15247B3 Multi Terrain Loader ESL00001-UP (MACHINE) POWERED BY C2.2 Eng...

21. Use Tooling (D) to remove retaining ring (42). Remove washer (43). Repeat Step 21 for the
other side.
Note: Return the piston to the original bore.
22. Remove piston (44) from rotor (40). Remove O-ring seal (45) and roller (46) from piston
(44).

23. Use Tooling (E) to remove split ring (47).
24. Remove washer (48).
25. Block front case (49). Use a suitable press to remove spindle (50).

26. Block spindle (50). Use a suitable press to remove studs (51).
27. Remove seal (52) from spindle (50).
28. Use Tooling (F) and Tooling (G) to remove bearing cone (53).

29. Remove bearing cone (54).
30. Remove seal (56). Remove bearing cup (55).
31. Remove seal (58). Remove bearing cup (57). Remove plug (59).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Thu Nov 7 20:16:41 UTC+0800 2019

Shutdown SIS
Previous Screen
i04590116
Piston Motor (Hydrostatic) - Disassemble - Two Speed
SMCS - 5058-015-H7
S/N - ESL1-UP
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1854 Retaining Ring Pliers 1
B 7S-8469 Bushing 1
C 1P-0510 Driver Gp 1
D 1P-1863 Retaining Ring Pliers 1
Start By:
a. Remove the motor.

1. Remove nut (1) and valve (2)
2. Remove O-ring seal (3), backup ring (4), O-ring seal (5), backup ring (6), O-ring seal (7),
and O-ring seal (8) from valve (2).

3. Use a suitable press in order to remove retaining ring (9) and lock (10).
4. Remove housing (11).
5. Remove the O-ring seal from housing (11).
6. Remove springs (12).

7. Use Tooling (A) in order to remove retaining ring (13).
8. Remove piston (14).
9. Use Tooling (A) in order to remove retaining ring (15).
11. Remove spring (17).

12. Use a suitable press in order to remove pin (18).
13. Remove valve (19).
14. Remove the spring from valve (19).
15. Remove seals (20).

17. Remove seals (22).
18. Remove radial motor (23).

19. Use a suitable press, Tooling (B), Tooling (C), and Tooling (D) in order to remove retaining
ring (24).
20. Remove shim (25).
21. Use a suitable press and Tooling (C) in order to remove shaft (26).
22. Remove bearing cone (27).

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

23. Remove bearing cone (28) and seal (29).
24. Remove bearing cup (30) and lip seal (31).
25. Remove bearing cup (32).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 7 20:17:37 UTC+0800 2019

Shutdown SIS
Previous Screen
i05269920
Piston Motor (Hydrostatic) - Disassemble - Final Drive Bench
Method
SMCS - 5058-015-H7
S/N - ESL1-UP
Table 1
Required Tools
Tools Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 136-1452 Retaining Ring Pliers As 1
C 1P-0074 Slide Hammer Puller Gp 1
D 5F-7339 Adapter 1
E 1P-1859 Retaining Ring Pliers 1
F 5P-5197 Retaining Ring Pliers As 1
G FT-3081 Adapter Plate 1
H
308-5676 Spanner Wrench Assembly(1)
1
329-1669 Spanner Wrench Assembly(2)
1
308-5675 Driver Assembly 1
J 127-8458 Final Drive Bench Ar 1
K 1H-3110 Bearing Puller Gp 1
(1)
6 Pin

(2)
7 Pin
Start By:
a. Remove the piston motor.
1. Remove bolts (1) and head (2).

2. Remove bearing (3) and seal (4).
3. Remove plug (5).
4. Remove O-ring seal (8) from plug (5).
5. Remove spring (7) and spool (6).
6. Repeat Step 4 for opposite side.

Caterpillar cat 247 b3 multi terrain loader (prefix esl) service repair manual (esl00001 and up)

Recommended

Recommended

More Related Content

Similar to Caterpillar cat 247 b3 multi terrain loader (prefix esl) service repair manual (esl00001 and up)

Similar to Caterpillar cat 247 b3 multi terrain loader (prefix esl) service repair manual (esl00001 and up) (9)

More from ujfjjsjekkmsmd

More from ujfjjsjekkmsmd (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 247 b3 multi terrain loader (prefix esl) service repair manual (esl00001 and up)