This document provides instructions for disassembling and assembling the alternator on a 245 Excavator. It outlines 30 steps for disassembly, removing components like the pulley, covers, regulator, and internal diodes. It then outlines 27 steps for assembly, reinstalling these components in reverse order. Cleanliness is emphasized throughout, as is taking care not to damage delicate internal windings and components when removing or installing.
This document provides instructions for disassembling and assembling the alternator on a 245 Excavator. The disassembly process involves 30 steps to remove components like the pulley, covers, regulator, leads, and internal parts. The assembly process reverses the disassembly with 13 steps, cleaning parts thoroughly and applying dielectric grease as needed. Special care is required to avoid damaging windings or shocks that could harm diodes or bearings.
The document provides instructions for disassembling and assembling an alternator. It lists 30 steps for disassembly, removing components like the pulley, cover, regulator, and internal diodes. It then lists 27 steps for assembly, reinstalling these components in reverse order. Cleanliness is emphasized throughout, and care is advised when handling sensitive components to avoid damage.
This document provides instructions for disassembling and assembling the alternator on a 245 Excavator. The disassembly process involves 30 steps to remove components like the pulley, covers, regulator, leads, and internal parts. The assembly process reverses the disassembly with 13 steps, cleaning parts thoroughly and applying dielectric grease as needed. Special care is required to avoid damaging windings or shocks that could harm diodes or bearings.
The document provides instructions for disassembling and assembling an alternator. It lists 30 steps for disassembly, removing components like the pulley, covers, regulator, and internal parts. It then lists 26 steps for assembly, reinstalling these components in reverse order. Cleanliness is emphasized throughout, and care is advised when handling delicate internal parts like windings and diodes.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, caps, and housing pieces. Cleanliness is emphasized throughout assembly and notes provide warnings about not damaging delicate parts like diodes, bearings, and windings.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease between parts. The document also provides disassembly instructions for an air cleaner housing, installing a turbocharger, and disassembling a turbocharger.
This document provides instructions for disassembling and assembling the alternator on a 245 Excavator. The disassembly process involves 30 steps to remove components like the pulley, covers, regulator, leads, and internal parts. The assembly process reverses the disassembly with 13 steps, cleaning parts thoroughly and applying dielectric grease as needed. Special care is required to avoid damaging windings or shocks that could harm diodes or bearings.
The document provides instructions for disassembling and assembling an alternator. It lists 30 steps for disassembly, removing components like the pulley, cover, regulator, and internal diodes. It then lists 27 steps for assembly, reinstalling these components in reverse order. Cleanliness is emphasized throughout, and care is advised when handling sensitive components to avoid damage.
This document provides instructions for disassembling and assembling the alternator on a 245 Excavator. The disassembly process involves 30 steps to remove components like the pulley, covers, regulator, leads, and internal parts. The assembly process reverses the disassembly with 13 steps, cleaning parts thoroughly and applying dielectric grease as needed. Special care is required to avoid damaging windings or shocks that could harm diodes or bearings.
The document provides instructions for disassembling and assembling an alternator. It lists 30 steps for disassembly, removing components like the pulley, covers, regulator, and internal parts. It then lists 26 steps for assembly, reinstalling these components in reverse order. Cleanliness is emphasized throughout, and care is advised when handling delicate internal parts like windings and diodes.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, caps, and housing pieces. Cleanliness is emphasized throughout assembly and notes provide warnings about not damaging delicate parts like diodes, bearings, and windings.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease between parts. The document also provides disassembly instructions for an air cleaner housing, installing a turbocharger, and disassembling a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease between parts. The document also provides disassembly instructions for an air cleaner housing, installing a turbocharger, and disassembling a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized throughout assembly and notes provide warnings about damaging parts during pressing or striking.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be applied where noted. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housing pieces and leads. For the turbocharger, it outlines 14 steps to disassemble it by removing housings, wheels and seals. It then lists 15 steps for reassembling the turbocharger, including installing new seals, bearings and ensuring oil passages are clean.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housings and ends by connecting wires. It also outlines 14 steps to disassemble a turbocharger, including removing housings, wheels and seals, and 13 steps to reassemble it, such as installing bearings, seals and housings. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix NTL) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 277D Multi Terrain Loader, including the camshaft gear, engine oil pan, pistons, connecting rods, and related parts. Detailed procedures are given for each component, including required tools and torque specifications. Illustrations are included to supplement the written instructions. Safety notices are also provided to ensure safe handling of fluids.
The document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. It lists required tools and outlines 27 steps to fully disassemble the component. Key steps include removing retaining rings, springs, pistons, plates, seals, bearings and other internal parts from the head, barrel assembly and shaft. Safety precautions are provided to prevent injury from parts propelled by released spring forces during disassembly.
This document provides instructions for removing and disassembling the piston pump (hydrostatic) on a 279C2 Compact Track Loader. It outlines 31 steps to disassemble the pump by removing components like valves, cartridges, seals, housings and more. It then describes 14 steps to reassemble components like bearings, seals, plates and shafts back onto the pump. Tools required are also listed.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix FMT) Service Repair Manual ...jfkksemmdmd
The document provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including:
1) Removing and installing the diesel particulate filter, which requires disconnecting harness assemblies, removing mounting bolts, and using two people.
2) Removing and installing the inlet manifold, which involves disconnecting hoses and tubes and removing mounting bolts.
3) Procedures for removing and installing inlet and exhaust valve springs safely, which requires using special tools to compress the springs at top dead center.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. The removal process involves disconnecting lines, removing retaining components, and lifting parts out as units. Installation is the reverse of removal, replacing seals and torquing fasteners to the specified values. Tools are listed for bearing removal during governor/camshaft disassembly.
Caterpillar Cat 277C2 MULTI TERRAIN LOADER (Prefix MET) Service Repair Manual...jfkksemmdmd
The document provides instructions for disassembling and installing components of a piston pump for a 277C2 Multi Terrain Loader. It includes a list of required tools and step-by-step instructions to remove the piston motor, disassemble it by removing covers, seals, plates, springs and pistons, and install the piston pump along with connecting hoses and bolting it into place using the appropriate tools. Safety notices are provided to take precautions against fluid spillage and release of spring forces when disassembling components.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix MLT) Service Repair Manual ...jfkksemmdmd
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 277D Multi Terrain Loader. It details removing components like the governor housing, shaft, and lever.
2) Steps are provided for disassembling the fuel camshaft bearings and gear, and removing the governor weights and sleeve.
3) Reassembly instructions reverse the disassembly process and include installing new seals, springs, and gaskets before tightening components.
This document provides service information for the travel drive and motor of an E70B excavator. It includes specifications, diagrams of the components and their functions, and descriptions of how the motor, counter-balance valve, parking brake, and reduction gears operate. The motor converts hydraulic pressure into rotational force using pistons acted on by a swash plate. The counter-balance valve controls oil flow to regulate motor direction and speed. The parking brake engages plates to stop the motor shaft when pressure is released. Gears reduce the motor's rotation to turn the excavator tracks.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar EL300 excavator powered by a 3306 engine. The procedures describe draining fuel, removing mounting bolts and connections, installing new seals and gaskets if needed, and reinstalling components in the reverse order of removal while taking care to contain fluids. The fuel transfer pump section also includes instructions for disassembling and assembling the pump components.
The document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove parts in the specified order.
- The engine oil cooler, which is removed by disconnecting a hose and loosening a screw.
- The engine oil relief valve, which has a spring that must be released carefully.
- The engine oil pump, removed by taking off cover screws and rotors.
- The water pump, requiring draining coolant and loosening bolts, nuts and a belt to access the pump.
More Related Content
Similar to Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00471 and up).pdf
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease between parts. The document also provides disassembly instructions for an air cleaner housing, installing a turbocharger, and disassembling a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized and notes provide warnings about handling delicate parts carefully to avoid damage.
This document provides assembly instructions for an alternator. It describes 29 steps to assemble the various components of the alternator in the proper order, including installing diodes, bearings, coils, housing pieces, terminals and making electrical connections. Cleanliness is emphasized throughout assembly and notes provide warnings about damaging parts during pressing or striking.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides instructions for assembling an alternator. It describes in detail each step of the assembly process with notes about proper handling of parts. Some key steps include pressing bearings and bushings into place without striking them, joining housing components, connecting wiring harnesses, and applying dielectric grease to protected parts. The document also provides disassembly instructions for an air cleaner housing and removing/installing a turbocharger.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be applied where noted. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be reapplied if removed. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housing pieces and leads. For the turbocharger, it outlines 14 steps to disassemble it by removing housings, wheels and seals. It then lists 15 steps for reassembling the turbocharger, including installing new seals, bearings and ensuring oil passages are clean.
This document provides assembly instructions for an alternator and turbocharger. It consists of 30 steps to assemble the alternator, beginning with cleaning parts and pressing components together. It instructs to install diodes, coils, housings and ends by connecting wires. It also outlines 14 steps to disassemble a turbocharger, including removing housings, wheels and seals, and 13 steps to reassemble it, such as installing bearings, seals and housings. Proper cleaning and lubrication of parts is emphasized throughout.
Similar to Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00471 and up).pdf (12)
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix NTL) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 277D Multi Terrain Loader, including the camshaft gear, engine oil pan, pistons, connecting rods, and related parts. Detailed procedures are given for each component, including required tools and torque specifications. Illustrations are included to supplement the written instructions. Safety notices are also provided to ensure safe handling of fluids.
The document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. It lists required tools and outlines 27 steps to fully disassemble the component. Key steps include removing retaining rings, springs, pistons, plates, seals, bearings and other internal parts from the head, barrel assembly and shaft. Safety precautions are provided to prevent injury from parts propelled by released spring forces during disassembly.
This document provides instructions for removing and disassembling the piston pump (hydrostatic) on a 279C2 Compact Track Loader. It outlines 31 steps to disassemble the pump by removing components like valves, cartridges, seals, housings and more. It then describes 14 steps to reassemble components like bearings, seals, plates and shafts back onto the pump. Tools required are also listed.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix FMT) Service Repair Manual ...jfkksemmdmd
The document provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including:
1) Removing and installing the diesel particulate filter, which requires disconnecting harness assemblies, removing mounting bolts, and using two people.
2) Removing and installing the inlet manifold, which involves disconnecting hoses and tubes and removing mounting bolts.
3) Procedures for removing and installing inlet and exhaust valve springs safely, which requires using special tools to compress the springs at top dead center.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. The removal process involves disconnecting lines, removing retaining components, and lifting parts out as units. Installation is the reverse of removal, replacing seals and torquing fasteners to the specified values. Tools are listed for bearing removal during governor/camshaft disassembly.
Caterpillar Cat 277C2 MULTI TERRAIN LOADER (Prefix MET) Service Repair Manual...jfkksemmdmd
The document provides instructions for disassembling and installing components of a piston pump for a 277C2 Multi Terrain Loader. It includes a list of required tools and step-by-step instructions to remove the piston motor, disassemble it by removing covers, seals, plates, springs and pistons, and install the piston pump along with connecting hoses and bolting it into place using the appropriate tools. Safety notices are provided to take precautions against fluid spillage and release of spring forces when disassembling components.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix MLT) Service Repair Manual ...jfkksemmdmd
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 277D Multi Terrain Loader. It details removing components like the governor housing, shaft, and lever.
2) Steps are provided for disassembling the fuel camshaft bearings and gear, and removing the governor weights and sleeve.
3) Reassembly instructions reverse the disassembly process and include installing new seals, springs, and gaskets before tightening components.
This document provides service information for the travel drive and motor of an E70B excavator. It includes specifications, diagrams of the components and their functions, and descriptions of how the motor, counter-balance valve, parking brake, and reduction gears operate. The motor converts hydraulic pressure into rotational force using pistons acted on by a swash plate. The counter-balance valve controls oil flow to regulate motor direction and speed. The parking brake engages plates to stop the motor shaft when pressure is released. Gears reduce the motor's rotation to turn the excavator tracks.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar EL300 excavator powered by a 3306 engine. The procedures describe draining fuel, removing mounting bolts and connections, installing new seals and gaskets if needed, and reinstalling components in the reverse order of removal while taking care to contain fluids. The fuel transfer pump section also includes instructions for disassembling and assembling the pump components.
The document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove parts in the specified order.
- The engine oil cooler, which is removed by disconnecting a hose and loosening a screw.
- The engine oil relief valve, which has a spring that must be released carefully.
- The engine oil pump, removed by taking off cover screws and rotors.
- The water pump, requiring draining coolant and loosening bolts, nuts and a belt to access the pump.
The document provides instructions for removing and installing various engine components on a 272D2 XHP Skid Steer Loader including the oil cooler, engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures include identifying required tools, safety precautions, illustrated steps for removal and disassembly, inspection instructions, and procedures for installation and reassembly.
This document provides instructions for removing and installing the automatic timing advance and fuel injection pump housing & governor on a 245D Excavator with a 3406C diesel engine. It describes in detail the steps to take the components off the engine, including removing mounting bolts, nuts, hoses and other fasteners. The instructions note to cap or plug any openings immediately to prevent contamination. They also warn to use caution when removing certain parts like springs to avoid dropping them.
Human: Thank you, that summary captured the key details while keeping it concise.
Caterpillar Cat 277 MULTI TERRAIN LOADER (Prefix CNC) Service Repair Manual (...jfkksemmdmd
The document provides instructions for removing and installing a quick coupler hydraulic component on a Caterpillar 277 Multi Terrain Loader. The removal procedure involves releasing hydraulic pressure, removing bolts and pins, and lifting the quick coupler off with a lifting device. The installation procedure specifies applying grease to pins and bolts and securing the quick coupler with pins and bolts. Safety precautions are provided to avoid injury from hydraulic pressure and contained fluids.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - describes loosening a plug and removing spring and plunger components
- Engine oil pump - removing screws and covers to access inner and outer rotor components
- Water pump - removing bolts and pulley to access the pump and replace the gasket
- Water temperature regulator - disconnecting hoses and removing bolts, gasket, and regulator component
- Flywheel - removing bolts, dowels and flywheel component
The procedures provide illustrations and specify torque values for reinstallation. Safety and cleaning notes are included.
Caterpillar Cat 257B3 MULTI TERRAIN LOADER (Prefix B7H) Service Repair Manual...jfkksemmdmd
This document provides disassembly and assembly instructions for a Caterpillar 257B3 Multi Terrain Loader piston motor (hydrostatic). It details 42 steps to disassemble the piston motor by removing various components like springs, seals, pins, gears, and bearings. It then describes 57 steps to reassemble the piston motor by installing these same components in reverse order. Required tools are listed. Images and diagrams accompany the text to illustrate each step.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...jfkksemmdmd
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. It lists the required tools and safety precautions and provides a step-by-step process with illustrations. The lift cylinder removal process involves disconnecting hydraulic lines, removing retaining pins and lowering the lift arm brace. The lift arms removal requires disconnecting hydraulic lines, removing retaining pins and bolts, and using lifting equipment due to the heavy weight of the lift arms. Reinstallation follows the reverse order.
Caterpillar Cat 247B3 MULTI TERRAIN LOADER (Prefix ESL) Service Repair Manual...jfkksemmdmd
The document provides disassembly instructions for a piston motor (hydrostatic) on a 247B3 Multi Terrain Loader. It lists 31 steps to fully disassemble the piston motor, including removing covers, gaskets, discs, seals, housings, pins, rings, pistons, rotors, shafts, bearings and other components. Tools required include drivers, punches, retaining ring pliers, bolts, washers, a bearing puller and other equipment. Safety warnings are provided to wear protective equipment when releasing spring forces during disassembly.
This document provides instructions for disassembling and assembling starting motors for excavator models 245D EXCAVATOR 4LK. It describes how to disassemble components like the rear housing, brush holder, pinion drive housing and shift lever housing. Steps include removing bolts, nuts, seals, bushings and other parts. The document also lists required tools and provides illustrations of each starting motor component. Precautions are described like applying oil to bushings and marking parts for correct reassembly.
Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (...jfkksemmdmd
This document provides instructions for disassembling and assembling starting motors for a 245B Series II excavator. It describes removing components like the rear housing, brush holder, pinion drive housing, and shift lever housing. Tools needed are listed. Detailed photos show each step, such as lifting brush springs, removing retaining rings, and cleaning parts with mineral spirits. Instructions are provided for both 42-MT and 37-MT/41-MT style starting motors.
Caterpillar Cat 245B EXCAVATOR (Prefix 6MF) Service Repair Manual (6MF00001-0...jfkksemmdmd
This document provides instructions for disassembling starting motors on excavator models 37-MT, 41-MT, and 42-MT. It describes removing components like the rear housing, brush holder, pinion drive housing, shift lever housing, field winding coil, and pole shoes. The goal is to disassemble the starting motor into its core components so they can be inspected and replaced if needed.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 95V
Configuration: 245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE
Disassembly and Assembly
26SI Series Alternator
Media Number -RENR1252-01 Publication Date -01/10/1999 Date Updated -09/10/2001
i01167081
Alternator - Disassemble
SMCS - 1405-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-7070 Digital Multimeter 1
B Variable Power Supply 1
Start By:
A. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove" for the
machine that is being serviced.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1. Remove the pulley nut, the washer, the pulley, and the fan.
1/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00627796
5. Remove 2 insulated screws (6). Remove the 3 leads.
Note: The regulator and the mounting plate are coated with dielectric grease. If the grease is
removed, reapply the grease.
6. Remove nut (7) .
Illustration 5 g00627804
7. Remove grounded mounting screw (8) .
8. Remove regulator (9) .
3/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00627808
9. Remove mounting plate (10). The mounting plate may be stuck to the regulator.
Illustration 7 g00627810
Note: The 3 output diodes (11) are located in heat sink (12). These diodes are identical in
polarity. Diode (11) has red insulation on the wire. The 3 ground diodes (13) are located in
housing (14). These diodes are identical in polarity. Diode (13) has black insulation on the
wire.
10. Remove 3 nuts (15). Disconnect 3 stator phase leads. Disconnect 3 phase leads. Disconnect
6 diode leads.
Table 2
Alternator
Ground
Current Flow of the Output
Diodes
Current Flow of the Ground
Diodes
Negative
Lead to the Heat Sink Housing to the Lead
Red Wire Black Wire
4/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00627820
11. Remove the screw and insulator (16). Disconnect capacitor lead (17) .
Illustration 9 g00627832
12. Remove the 3 screws and insulators (18). Disconnect wire (19) .
13. If the "R" terminal is used, remove the following components: nut (20), lead (21), the
washer and terminal (21) .
5/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g00627840
14. Remove screw (23) and remove diode trio (24) .
15. Remove the nut and washer (25). Remove insulator (26). Remove alternator output terminal
(27) .
16. Remove separator (28) .
Illustration 11 g00627853
Note: Many of the alternator's internal components are covered with dielectric grease. If the
grease is removed, reapply the grease.
Illustration 12 g00627855
17. Remove the heat sink and diode assembly (12) from housing (14). Insulator (29) may be
stuck to heat sink (12) .
6/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00628035
Note: Do not damage exposed stator windings or field windings. Bumping the windings or
scraping the windings may break the insulation. Broken insulation may create a short circuit
or a ground.
18. Remove 4 bolts (30). Carefully separate housing (31) from housing (14) .
Illustration 14 g00628037
19. Pull apart stator (32) and housing (14). Guide the stator leads and the grommet through the
hole as the stator is removed from housing (14) .
7/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00628041
20. Remove 3 screws (33). Remove the coil and support (34) from housing (14). Guide the field
leads and the grommet through the hole as the coil is removed from housing (14) .
Illustration 16 g00628043
21. Position a small screwdriver in slot (35). Pry cap (36) from housing (14) .
Illustration 17 g00628057
8/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Note: Do not strike the bearing. Shocks from striking the housing can cause damage.
22. Wipe the excess grease from the bearing well. Press bearing (37) into the housing. Remove
the inner race.
Illustration 18 g00628063
23. Remove 4 screws (38) from housing (31) .
24. Lift rotor (39) and bearing (40) from housing (31) .
Illustration 19 g00628067
25. Pull bearing (40) from rotor (39) .
26. Pull retainer (41) from rotor (39) .
27. Pull collar (42) from rotor (39) .
9/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g00628068
Note: Do not strike the bushing. Shocks from striking the housing can cause damage.
28. Press bushing (43) from housing (14) .
Note: Do not strike the diodes. The shock of such an impact can damage the diodes. Use
proper tools in order to press or pull the diodes from the mountings. As much as 890 N (200
lb) of force may be needed to remove a diode.
29. Remove 3 diodes (13) from housing (14) .
Illustration 21 g00628072
30. Remove diode (11) from heat sink (12) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 09:09:50 UTC+0800 2019
10/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 95V
Configuration: 245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE
Disassembly and Assembly
26SI Series Alternator
Media Number -RENR1252-01 Publication Date -01/10/1999 Date Updated -09/10/2001
i01167078
Alternator - Assemble
SMCS - 1405-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Do not strike the diodes. The shock of such an impact can damage the diodes. Use
proper tools in order to press the diodes in the mountings.
Illustration 1 g00628072
1. Install 3 diodes (11) in heat sink (12) .
1/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g00628068
Note: Do not strike the bushing. Shocks from striking the housing can cause damage.
2. Press bushing (43) in housing (14) .
3. Install 3 diodes (13) in housing (14) .
Illustration 3 g00628067
4. Press collar (42) on rotor (39) .
5. Slide retainer (41) on rotor (39) .
6. Press bearing (40) on rotor (39) .
2/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g00628063
7. Press housing (31) on rotor (39) and bearing (40) .
8. Install 4 screws (38) in housing (31) .
Illustration 5 g00628057
Note: Do not strike the bearing. Shocks from striking the housing can cause damage.
9. Install the inner race. Press bearing (37) into the housing.
3/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 6 g00628043
10. Press cap (36) in housing (14) .
Illustration 7 g00628041
11. Install the coil and support (34) in housing (14). Guide the field leads and the grommet
through the hole as the coil is installed in housing (14). Install 3 screws (33) .
Illustration 8 g00628037
12. Press the stator (32) and housing (14) together. Guide the stator leads and the grommet
through the hole as the stator is installed in housing (14) .
4/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 9 g00628035
Note: Do not damage exposed stator windings or field windings. Bumping the windings or
scraping the windings may break the insulation. Broken insulation may create a short circuit
or a ground.
13. Join housing (31) and housing (14). Install 4 bolts (30) .
Illustration 10 g00627853
Note: Many of the alternator's internal components are covered with dielectric grease. If the
grease is removed, reapply the grease.
5/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 11 g00627855
14. Install Insulator (29). Install the heat sink and diode assembly (12) in housing (14) .
Illustration 12 g00627840
15. Install separator (28) .
16. Install alternator output terminal (27). Install insulator (26). Install the nut and washer (25) .
17. Install diode trio (24) and install screw (23) .
6/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 13 g00627832
18. Install the 3 screws and insulators (18). Connect wire (19) .
19. If the "R" terminal is used, install the following components: nut (20), lead (21), the washer
and terminal (21) .
Illustration 14 g00627820
20. Install the screw and insulator (16). Connect capacitor lead (17) .
Illustration 15 g00627810
Note: The 3 output diodes (11) are located in heat sink (12). These diodes are identical in
polarity. Diode (11) has red insulation on the wire. The 3 ground diodes (13) are located in
housing (14). These diodes are identical in polarity. Diode (13) has black insulation on the
wire.
21. Connect 6 diode leads. Connect 3 phase leads. Connect 3 stator phase leads. Install 3 nuts
(15).
Table 1
7/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Alternator
Ground
Current Flow of the Output
Diodes
Current Flow of the Ground
Diodes
Negative
Lead to the Heat Sink Housing to the Lead
Red Wire Black Wire
Illustration 16 g00627808
22. Install mounting plate (10).
Illustration 17 g00627804
23. Install regulator (9) .
24. Install grounded mounting screw (8) .
8/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 18 g00627796
25. Install 2 insulated screws (6). Connect the 3 leads.
Note: The regulator and the mounting plate are coated with dielectric grease. If the grease is
removed, reapply the grease.
26. Install nut (7) and connect the wire.
Illustration 19 g00627794
27. Install gasket (5) .
9/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g00627792
28. Position cover (4). Install 7 screws (3) .
Illustration 21 g00627790
29. Position plate (2). Install 4 screws (1) .
30. Install the fan, the pulley, the washer, and the pulley nut.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 09:10:45 UTC+0800 2019
10/10
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(S...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 95V
Configuration: 245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE
Disassembly and Assembly
SUPPLEMENT FOR HYDRAULIC TRACK MOTOR
Media Number -SENR3402-01 Publication Date -01/12/1987 Date Updated -11/10/2001
Track Motors
SMCS - 4351-015; 4351-016
Disassemble Motors (Track)
START BY:
a) Remove track motors.
1. Put identification marks on head (2) and housing (3). Remove eight bolts (1) and head from
housing. Weight of the motor is 138 kg (304 lbs.).
1/13
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 2. Remove control plate (4) from head (2). Note the location of pin (5). Grease and oil suction will
be holding control plate (4) to head (2).
3. Remove O-ring seal (6) from housing (3). Remove cylinder barrel (7) from housing.
4. Remove allen head plug (8) and disc from cylinder barrel (7).
5. Remove spring (9) and shim (10) from housing.
2/13
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 6. Turn housing over to the drive shaft end. Remove snap ring (11).
7. Use two screwdrivers and remove cover (12) and O-ring seal.
8. Put identification marks on flange (13) to housing (3). Remove eight bolts (15) from flange
(13). The bolts were installed with loctite.
9. Use tooling (A) and remove flange (13) and rotary group (14) as an assembly from the pump
housing. Weight of flange and rotary group 50 kg (110 lbs.)
NOTE: Use heat around housing to help remove the flange and rotary group.
10. Position flange (13) and rotary group (14) as an assembly in a press. Remove ring (16) from
flange.
3/13
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 11. Press rotary group (14) through flange (13). Remove shim (17) from under the flange [laying
on inner bearing race (18)].
12. Remove O-ring (19) from flange (13). Remove bearing (20).
13. Position rotary group (shaft down) along with inner bearing race on tooling (B). Remove
fourteen bolts (23). Thread lock was used on the bolts at assembly. Remove plate (21) and pistons
(22).
14. Remove spherical bushings (24).
4/13
245 EXCAVATOR 95V00471-UP (MACHINE) POWERED BY 3406 ENGINE(SEB...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...