The document provides instructions to remove the fuel ratio control and fuel shutoff solenoid from a Caterpillar 3306 engine. It describes disconnecting fuel lines and electrical connections, removing mounting hardware, and noting the need to clean parts and apply thread lock compound. Technicians are advised to refer to other sections for adjustment procedures after installing these components.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903297
Fuel Ratio Control - Remove
SMCS - 1278-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/2
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00460630
1. Disconnect fuel pressure line (3). Remove two bolts (2) .
2. Move fuel ratio control (1) upward in order to disengage the fuel ratio control from the lever
assembly in the governor.
Illustration 2 g00460631
3. Remove four O-ring seals (4) and screen assembly (5) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:29:13 UTC+0800 2019
2/2
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903551
Fuel Ratio Control - Disassemble
SMCS - 1278-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
Start By:
A. Remove the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00460737
1. Remove cover (1) and O-ring seal (2) .
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. In order to release the spring force, hold cover (3) in position and slowly remove the two
bolts that hold cover (3) in place.
Illustration 2 g00460791
3. Remove spring (4), washer (5) and diaphragm (6) from retainer (7). Remove retainer (7)
from housing (8) .
2/3
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 3 g00460793
4. Remove nut (13) from valve extension (12) and remove valve extension (12) from retainer
(7). Remove stem (9) from valve extension (12). Remove spring (10) and O-ring seal (11)
from valve extension (12) .
Illustration 4 g00460795
5. Remove spring (14) and retainer (15) from housing (8) .
6. All parts should be cleaned and inspected. Replace all parts that are worn or damaged.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:30:09 UTC+0800 2019
3/3
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01135000
Fuel Ratio Control - Assemble
SMCS - 1278-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the condition of the O-ring and the diaphragm. If the O-ring or the diaphragm is
worn or damaged use new parts for replacement.
1/4
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00460801
1. Install spring (1) and retainer (2) into housing (3) .
Illustration 2 g00460828
2. Install O-ring seal (6) and spring (5) into valve extension (7). Install stem (4) into valve
extension (7). Secure valve extension (7) to retainer (8) with nut (9) .
Illustration 3 g00460830
2/4
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 3. Install stem (4) and retainer (8) into housing (3) .
Illustration 4 g00460912
4. Install diaphragm (12), washer (11) and spring (10) on retainer (8) .
Illustration 5 g00460914
Illustration 6 g00460917
3/4
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 5. Install cover (13) on housing (3). Secure cover (13) with two bolts and washers.
6. Install O-ring seal (15) onto cover (14) and install cover (14) onto cover (13). Secure cover
(14) with two bolts.
Note: Refer to Testing and Adjusting, "Fuel System" for additional information on the
adjustment procedure for the fuel ratio control.
End By: Install the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:31:05 UTC+0800 2019
4/4
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903481
Fuel Ratio Control - Install
SMCS - 1278-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00460631
1. Screen assembly (5) and four O-ring seals (4) should be inspected, replaced and installed.
1/2
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g00460630
2. Put fuel ratio control (1) in position and engage the fuel ratio control with the lever
assembly in the governor.
3. Install bolts (2) that hold the fuel ratio control and connect fuel pressure line (3) to fuel ratio
control (1). Refer to Testing and Adjusting, "Fuel System" for more information on the
adjustment procedure for the fuel ratio control.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:32:00 UTC+0800 2019
2/2
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00879991
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00475568
1. Remove nut (1) and the washer. Disconnect ground wire (4) from the fuel shutoff solenoid.
2. Remove two nuts (2) and the washers.
1/2
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 3. Remove fuel shutoff solenoid (3) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00475568
1. Install the gasket and fuel shutoff solenoid (3) .
2. Apply 9S-3263 Thread Lock Compound on the threads for two nuts (2) .
3. Install the washers and two nuts (2) .
4. Connect ground wire (4) to the fuel shutoff solenoid. Install nut (1) and the washer.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:32:56 UTC+0800 2019
2/2
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00930839
Automatic Timing Advance - Remove
SMCS - 1272-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-7307 Engine Turning Tool 1
B 0T-0065 Bolt 1
C
9S-9155 Spacer 1
8S-2264 Pump Impeller Puller 2
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Front Housing - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Follow the procedure in Steps 3 and 4 in order to time the fuel injection pump when the
front cover is removed. Follow the procedure in Steps 6 and 7 in order to time the fuel
injection pump when the front cover is installed.
Note: The No. 1 piston should be at the top center position on the compression stroke at the
start of all timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft
rotation is given.
Illustration 1 g00474593
2. Remove the electric starting motor and install Tool (A) .
Illustration 2 g00474592
3. Turn the crankshaft counterclockwise until the "C" on the crankshaft gear and the "C" on
the camshaft gear are in alignment.
2/4
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00474594
4. Remove two plugs and install Tool (B) in the flywheel housing. The large plug hole is for
viewing.
5. To find the top center compression stroke for the No. 1 piston, use Tool (A) in order to turn
the flywheel clockwise for approximately 30 degrees. This procedure should be used to
remove all of the end play from the timing gears.
6. Use Tool (A) in order to turn the flywheel counterclockwise in the direction of the engine
rotation until Tool (B) can be installed in the flywheel. The piston is at the top center
position.
Note: If you go past the bolt hole, you must start the procedure again.
Note: Remove the breather assembly from the valve mechanism cover. The piston is at the
top center position on the compression stroke when the inlet valve is closed and the exhaust
valve is closed for the No. 1 cylinder. You must be able to move the rocker arms up and
down with your hand.
Illustration 4 g00474595
7. Remove bolt (1) and washer (2) that secures the automatic timing advance.
NOTICE
3/4
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. The automatic timing advance must have support during removal in
order to help prevent damage to components.
Illustration 5 g00474596
8. Install bolt (1) and leave a 6.35 mm (.250 inch) gap. Install Tool (C), as shown. Tighten the
stud in order to loosen the fuel pump drive gear from the taper on the fuel injection pump
camshaft.
9. Remove Tool (C) and bolt (1). Remove the automatic timing advance.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:33:52 UTC+0800 2019
4/4
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935438
Automatic Timing Advance - Disassemble
SMCS - 1272-015
Disassembly Procedure
Start By:
A. Remove the automatic timing advance unit. Refer to Disassembly and Assembly,
"Automatic Timing Advance - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00476292
1/3
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 1. Remove two screws (1) and plate (2) .
NOTICE
The weights are held in position with two springs for each weight that
is under compression. Carefully remove the weights and the springs in
order to help prevent possible injury.
Illustration 2 g00476293
2. Remove springs (3) and (5), weight (6) and slide (4) from each side of the assembly.
2/3
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g00476294
3. If necessary, remove gear (7). Remove seals (8) and (9) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:34:48 UTC+0800 2019
3/3
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935599
Automatic Timing Advance - Assemble
SMCS - 1272-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g00476382
1. If dowels (3) were removed from the gear hub, installation dimension (X) is 9.00 ± 0.50 mm
(.354 ± .020 inch).
2. Install seals (4) and (5) .
3. Put gear (1) in position on hub assembly (2) .
Illustration 2 g00476383
4. Install slide (7), weight (9) and springs (6) and (8) on each side of the assembly.
2/3
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 3 g00476385
5. Install plate (11) with two screws (10) .
End By: Install the automatic timing advance unit. Refer to Disassembly and Assembly,
"Automatic Timing Advance - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:35:44 UTC+0800 2019
3/3
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935398
Automatic Timing Advance - Install
SMCS - 1272-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4186 Fuel Pump Timing Pin 1
B 0L-2070 Bolt 1
C 5P-7307 Engine Turning Tool 1
D 4C-9874 Spanner Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g00476281
1. Install washer (1) and bolt (2). Ensure that the cover of the fuel pump housing is removed.
Turn the fuel pump camshaft in the direction of the engine rotation until Tool (A) can be
installed in the notch of the camshaft.
2. Install Tool (A) and (B) into position. Install the weight assembly for the timing advance on
the fuel injection pump camshaft.
Illustration 2 g00476286
3. Use Tool (D) on the automatic timing advance and maintain a constant torque of 68 N·m
(50 lb ft). Tighten the bolt that fastens the automatic timing advance to the fuel pump
camshaft to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
4. Remove Tools (A), (B), (C) and (D). Install the starting motor.
End By: Install the front housing. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:36:39 UTC+0800 2019
2/2
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 1 g00589938
3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal
is damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
Illustration 2 g00452289
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch).
2/5
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...