Caterpillar Cat 235B EXCAVATOR (Prefix 7WC) Service Repair Manual (7WC00001 and up).pdf

Service Repair Manual
Model
235B EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235B EXCAVATOR 7WC
Configuration: 235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903297
Fuel Ratio Control - Remove
SMCS - 1278-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/2
235B EXCAVATOR 7WC00001-UP (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00460630
1. Disconnect fuel pressure line (3). Remove two bolts (2) .
2. Move fuel ratio control (1) upward in order to disengage the fuel ratio control from the lever
assembly in the governor.
3. Remove four O-ring seals (4) and screen assembly (5) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 22:29:13 UTC+0800 2019
2/2
2019/9/18

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00903551
Fuel Ratio Control - Disassemble
SMCS - 1278-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
Start By:
A. Remove the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Remove".
NOTICE
1/3
2019/9/18

1. Remove cover (1) and O-ring seal (2) .
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. In order to release the spring force, hold cover (3) in position and slowly remove the two
bolts that hold cover (3) in place.
3. Remove spring (4), washer (5) and diaphragm (6) from retainer (7). Remove retainer (7)
from housing (8) .
2/3
2019/9/18

4. Remove nut (13) from valve extension (12) and remove valve extension (12) from retainer
(7). Remove stem (9) from valve extension (12). Remove spring (10) and O-ring seal (11)
from valve extension (12) .
5. Remove spring (14) and retainer (15) from housing (8) .
6. All parts should be cleaned and inspected. Replace all parts that are worn or damaged.
Wed Sep 18 22:30:09 UTC+0800 2019
3/3
2019/9/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01135000
Fuel Ratio Control - Assemble
SMCS - 1278-016
Assembly Procedure
Table 1
Required Tools
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
NOTICE
Note: Check the condition of the O-ring and the diaphragm. If the O-ring or the diaphragm is
worn or damaged use new parts for replacement.
1/4
2019/9/18

1. Install spring (1) and retainer (2) into housing (3) .
2. Install O-ring seal (6) and spring (5) into valve extension (7). Install stem (4) into valve
extension (7). Secure valve extension (7) to retainer (8) with nut (9) .
2/4
2019/9/18

3. Install stem (4) and retainer (8) into housing (3) .
4. Install diaphragm (12), washer (11) and spring (10) on retainer (8) .
3/4
2019/9/18

5. Install cover (13) on housing (3). Secure cover (13) with two bolts and washers.
6. Install O-ring seal (15) onto cover (14) and install cover (14) onto cover (13). Secure cover
(14) with two bolts.
Note: Refer to Testing and Adjusting, "Fuel System" for additional information on the
adjustment procedure for the fuel ratio control.
End By: Install the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Install".
Wed Sep 18 22:31:05 UTC+0800 2019
4/4
2019/9/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00903481
Fuel Ratio Control - Install
SMCS - 1278-012
Installation Procedure
NOTICE
1. Screen assembly (5) and four O-ring seals (4) should be inspected, replaced and installed.
1/2
2019/9/18

2. Put fuel ratio control (1) in position and engage the fuel ratio control with the lever
assembly in the governor.
3. Install bolts (2) that hold the fuel ratio control and connect fuel pressure line (3) to fuel ratio
control (1). Refer to Testing and Adjusting, "Fuel System" for more information on the
adjustment procedure for the fuel ratio control.
Wed Sep 18 22:32:00 UTC+0800 2019
2/2
2019/9/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00879991
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
NOTICE
1. Remove nut (1) and the washer. Disconnect ground wire (4) from the fuel shutoff solenoid.
2. Remove two nuts (2) and the washers.
1/2
2019/9/18

3. Remove fuel shutoff solenoid (3) and the gasket.
NOTICE
1. Install the gasket and fuel shutoff solenoid (3) .
2. Apply 9S-3263 Thread Lock Compound on the threads for two nuts (2) .
3. Install the washers and two nuts (2) .
4. Connect ground wire (4) to the fuel shutoff solenoid. Install nut (1) and the washer.
Wed Sep 18 22:32:56 UTC+0800 2019
2/2
2019/9/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00930839
Automatic Timing Advance - Remove
SMCS - 1272-011
Removal Procedure
Table 1
Required Tools
A 5P-7307 Engine Turning Tool 1
B 0T-0065 Bolt 1
C
9S-9155 Spacer 1
8S-2264 Pump Impeller Puller 2
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Front Housing - Remove".
NOTICE
1/4
2019/9/18

1. Follow the procedure in Steps 3 and 4 in order to time the fuel injection pump when the
front cover is removed. Follow the procedure in Steps 6 and 7 in order to time the fuel
injection pump when the front cover is installed.
Note: The No. 1 piston should be at the top center position on the compression stroke at the
start of all timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft
rotation is given.
2. Remove the electric starting motor and install Tool (A) .
3. Turn the crankshaft counterclockwise until the "C" on the crankshaft gear and the "C" on
the camshaft gear are in alignment.
2/4
2019/9/18

4. Remove two plugs and install Tool (B) in the flywheel housing. The large plug hole is for
viewing.
5. To find the top center compression stroke for the No. 1 piston, use Tool (A) in order to turn
the flywheel clockwise for approximately 30 degrees. This procedure should be used to
remove all of the end play from the timing gears.
6. Use Tool (A) in order to turn the flywheel counterclockwise in the direction of the engine
rotation until Tool (B) can be installed in the flywheel. The piston is at the top center
position.
Note: If you go past the bolt hole, you must start the procedure again.
Note: Remove the breather assembly from the valve mechanism cover. The piston is at the
top center position on the compression stroke when the inlet valve is closed and the exhaust
valve is closed for the No. 1 cylinder. You must be able to move the rocker arms up and
down with your hand.
7. Remove bolt (1) and washer (2) that secures the automatic timing advance.
NOTICE
3/4
2019/9/18

The automatic timing advance must have support during removal in
order to help prevent damage to components.
8. Install bolt (1) and leave a 6.35 mm (.250 inch) gap. Install Tool (C), as shown. Tighten the
stud in order to loosen the fuel pump drive gear from the taper on the fuel injection pump
camshaft.
9. Remove Tool (C) and bolt (1). Remove the automatic timing advance.
Wed Sep 18 22:33:52 UTC+0800 2019
4/4
2019/9/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00935438
Automatic Timing Advance - Disassemble
SMCS - 1272-015
Disassembly Procedure
Start By:
A. Remove the automatic timing advance unit. Refer to Disassembly and Assembly,
"Automatic Timing Advance - Remove".
NOTICE
1/3
2019/9/18

1. Remove two screws (1) and plate (2) .
NOTICE
The weights are held in position with two springs for each weight that
is under compression. Carefully remove the weights and the springs in
order to help prevent possible injury.
2. Remove springs (3) and (5), weight (6) and slide (4) from each side of the assembly.
2/3
2019/9/18

3. If necessary, remove gear (7). Remove seals (8) and (9) .
Wed Sep 18 22:34:48 UTC+0800 2019
3/3
2019/9/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00935599
Automatic Timing Advance - Assemble
SMCS - 1272-016
Assembly Procedure
NOTICE
1/3
2019/9/18

1. If dowels (3) were removed from the gear hub, installation dimension (X) is 9.00 ± 0.50 mm
(.354 ± .020 inch).
2. Install seals (4) and (5) .
3. Put gear (1) in position on hub assembly (2) .
4. Install slide (7), weight (9) and springs (6) and (8) on each side of the assembly.
2/3
2019/9/18

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

5. Install plate (11) with two screws (10) .
End By: Install the automatic timing advance unit. Refer to Disassembly and Assembly,
"Automatic Timing Advance - Install".
Wed Sep 18 22:35:44 UTC+0800 2019
3/3
2019/9/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00935398
Automatic Timing Advance - Install
SMCS - 1272-012
Table 1
Required Tools
A 6V-4186 Fuel Pump Timing Pin 1
B 0L-2070 Bolt 1
C 5P-7307 Engine Turning Tool 1
D 4C-9874 Spanner Wrench 1
NOTICE
1/2
2019/9/18

1. Install washer (1) and bolt (2). Ensure that the cover of the fuel pump housing is removed.
Turn the fuel pump camshaft in the direction of the engine rotation until Tool (A) can be
installed in the notch of the camshaft.
2. Install Tool (A) and (B) into position. Install the weight assembly for the timing advance on
the fuel injection pump camshaft.
3. Use Tool (D) on the automatic timing advance and maintain a constant torque of 68 N·m
(50 lb ft). Tighten the bolt that fastens the automatic timing advance to the fuel pump
camshaft to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
4. Remove Tools (A), (B), (C) and (D). Install the starting motor.
End By: Install the front housing. Refer to Disassembly and Assembly, "Front Housing - Install".
Wed Sep 18 22:36:39 UTC+0800 2019
2/2
2019/9/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
1/5
2019/9/18

3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal
is damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch).
2/5
2019/9/18

Caterpillar Cat 235B EXCAVATOR (Prefix 7WC) Service Repair Manual (7WC00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 235B EXCAVATOR (Prefix 7WC) Service Repair Manual (7WC00001 and up).pdf

Similar to Caterpillar Cat 235B EXCAVATOR (Prefix 7WC) Service Repair Manual (7WC00001 and up).pdf (20)

More from hvy7sbkw8e

More from hvy7sbkw8e (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 235B EXCAVATOR (Prefix 7WC) Service Repair Manual (7WC00001 and up).pdf