The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C2.2 engine. It describes using tools to remove the flywheel bolts and install guide studs. The crankshaft rear seal is removed after the flywheel housing, and a new seal is installed with silicone sealant. The flywheel housing is reinstalled and torqued to specifications before reinstalling the flywheel.
Caterpillar cat 232 d skid steer loader (prefix kxc) service repair manual (k...ujdjkkskmme
- The document provides instructions for removing and installing a flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 232D skid steer loader engine.
- To remove the flywheel, tools are installed and bolts removed to lift the flywheel off. The ring gear may also need to be removed from the flywheel.
- To install the flywheel, cleaning is done and the ring gear is heated and pressed onto the flywheel if removed. The flywheel is positioned and bolts are tightened.
- Similar procedures using cleaning and sealant are described for removing and installing the crankshaft rear seal and an optional crankshaft wear sleeve.
Caterpillar cat 232 d skid steer loader (prefix kxc) service repair manual (k...fusjejfjskekem
1. The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C2.2 engine.
2. To remove the flywheel, mounting bolts must be removed and lifting tools installed to lift the heavy flywheel off of alignment dowels.
3. Flywheel installation requires cleaning surfaces, heating the ring gear for installation, aligning the flywheel on dowels, and torquing mounting bolts to the specified value.
4. Crankshaft rear seal removal requires removing the flywheel housing or back plate and pulling the old seal. Installation requires cleaning, applying sealant, pressing the new seal in place, and replacing the
Caterpillar cat 422 e backhoe loader (prefix dsk) service repair manual (dsk0...fjskekfkemm
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar C4.4 engine. It describes removing the flywheel by uninstalling bolts using guide bolts and lifting equipment due to the flywheel's weight of approximately 71 kg. It also details removing the flywheel housing by lifting it off after uninstalling bolts, potentially removing a dust seal. Reinstallation involves cleaning parts, installing dowels and bolts, and checking seal alignment with a dial indicator.
Caterpillar cat 422 e backhoe loader (prefix dsk) service repair manual (dsk0...ujjfkskeksmem
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. To remove the flywheel, bolts must first be removed using guide bolts for support. The crankshaft rear seal is removed by taking out torx screws, and a new seal is installed by aligning it with a plastic sleeve and cylinder block holes before tightening screws in a specified sequence.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
The document provides instructions for removing and installing a flywheel, crankshaft rear seal, flywheel housing, and vibration damper and pulley on a Caterpillar 320D2L excavator engine. Key steps include using guide studs and lifting devices to position parts, inspecting and replacing seals if needed, cleaning surfaces, and tightening bolts to specified torques. Tools and replacement parts are also listed.
The document provides instructions for removing and installing a flywheel, crankshaft rear seal, flywheel housing, and vibration damper and pulley on a Caterpillar 320D2L excavator engine. Key steps include using guide studs and lifting devices to position parts, inspecting and replacing seals if needed, cleaning surfaces, and tightening bolts to specified torques. Tools and replacement parts are also listed.
The document provides instructions for installing and removing a flywheel housing on a Caterpillar 320D2L excavator. It describes:
1) Removing bolts and installing guide studs to support the housing before lifting it off using a device.
2) Inspecting the crankshaft rear seal for leaks and replacing if needed before installation.
3) Cleaning the housing and cylinder block, installing dowels if needed, and bolting the housing back in place.
Caterpillar cat 232 d skid steer loader (prefix kxc) service repair manual (k...ujdjkkskmme
- The document provides instructions for removing and installing a flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 232D skid steer loader engine.
- To remove the flywheel, tools are installed and bolts removed to lift the flywheel off. The ring gear may also need to be removed from the flywheel.
- To install the flywheel, cleaning is done and the ring gear is heated and pressed onto the flywheel if removed. The flywheel is positioned and bolts are tightened.
- Similar procedures using cleaning and sealant are described for removing and installing the crankshaft rear seal and an optional crankshaft wear sleeve.
Caterpillar cat 232 d skid steer loader (prefix kxc) service repair manual (k...fusjejfjskekem
1. The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C2.2 engine.
2. To remove the flywheel, mounting bolts must be removed and lifting tools installed to lift the heavy flywheel off of alignment dowels.
3. Flywheel installation requires cleaning surfaces, heating the ring gear for installation, aligning the flywheel on dowels, and torquing mounting bolts to the specified value.
4. Crankshaft rear seal removal requires removing the flywheel housing or back plate and pulling the old seal. Installation requires cleaning, applying sealant, pressing the new seal in place, and replacing the
Caterpillar cat 422 e backhoe loader (prefix dsk) service repair manual (dsk0...fjskekfkemm
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar C4.4 engine. It describes removing the flywheel by uninstalling bolts using guide bolts and lifting equipment due to the flywheel's weight of approximately 71 kg. It also details removing the flywheel housing by lifting it off after uninstalling bolts, potentially removing a dust seal. Reinstallation involves cleaning parts, installing dowels and bolts, and checking seal alignment with a dial indicator.
Caterpillar cat 422 e backhoe loader (prefix dsk) service repair manual (dsk0...ujjfkskeksmem
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. To remove the flywheel, bolts must first be removed using guide bolts for support. The crankshaft rear seal is removed by taking out torx screws, and a new seal is installed by aligning it with a plastic sleeve and cylinder block holes before tightening screws in a specified sequence.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
The document provides instructions for removing and installing a flywheel, crankshaft rear seal, flywheel housing, and vibration damper and pulley on a Caterpillar 320D2L excavator engine. Key steps include using guide studs and lifting devices to position parts, inspecting and replacing seals if needed, cleaning surfaces, and tightening bolts to specified torques. Tools and replacement parts are also listed.
The document provides instructions for removing and installing a flywheel, crankshaft rear seal, flywheel housing, and vibration damper and pulley on a Caterpillar 320D2L excavator engine. Key steps include using guide studs and lifting devices to position parts, inspecting and replacing seals if needed, cleaning surfaces, and tightening bolts to specified torques. Tools and replacement parts are also listed.
The document provides instructions for installing and removing a flywheel housing on a Caterpillar 320D2L excavator. It describes:
1) Removing bolts and installing guide studs to support the housing before lifting it off using a device.
2) Inspecting the crankshaft rear seal for leaks and replacing if needed before installation.
3) Cleaning the housing and cylinder block, installing dowels if needed, and bolting the housing back in place.
The document provides instructions for removing and installing a flywheel, crankshaft rear seal, flywheel housing, and vibration damper and pulley on a Caterpillar 320D2L excavator engine. The summary is:
1. The instructions describe removing bolts and tools to separate the flywheel, crankshaft rear seal, flywheel housing, and vibration damper and pulley from the engine.
2. Cleaning procedures and inspections for leaks are provided before reinstalling components.
3. Components are reinstalled by aligning parts, inserting bolts, and tightening to the specified torques.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting and replacing seals, installing dowels and gaskets, and tightening bolts to the specified torques.
This document provides instructions for installing a flywheel and crankshaft rear seal on a 320 GC excavator. It describes removing the flywheel, installing guide studs, positioning the flywheel onto the crankshaft, and tightening bolts while preventing rotation. It also details removing the crankshaft rear seal, ensuring surfaces are clean, and pushing a new seal onto the crankshaft before tightening screws in a specific sequence. The document gives similar instructions for removing and installing a wet back end flywheel housing.
This document provides instructions for installing a flywheel and crankshaft rear seal on a 320 GC excavator. It describes removing the flywheel, installing guide studs, positioning the flywheel onto the crankshaft, and tightening bolts while preventing rotation. It also details removing the crankshaft rear seal, ensuring surfaces are clean, and pushing a new seal onto the crankshaft before tightening screws in a specific sequence. The document gives similar instructions for removing and installing a wet back end flywheel housing.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
1) The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 320 GC excavator. It describes cleaning and preparing the components, using guide studs and lifting devices to position the heavy parts, and tightening bolts to the specified torques.
2) The instructions also cover removing and installing a wet back-end flywheel housing. This involves removing bolts and seals, cleaning surfaces, pressing in a new oil seal, and aligning dowels and gaskets before tightening bolts to graded torque values.
3) Tools, torque specifications, and safety precautions are provided to ensure correct disassembly and reassembly of the engine components.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 3054C engine. It describes the required tools and parts, cleaning requirements, installation procedures including torque specifications, and references other documents for additional information.
CASE IH STX450 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The instructions cover disconnecting batteries, removing the radiator, hood, fuel lines, air intake components, and other parts to fully separate the engine from the tractor.
CASE IH STX440 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The instructions cover disconnecting batteries, removing the radiator, hood, fuel lines, air intake components, and other parts to fully separate the engine from the tractor.
CASE IH STX375 Tractor Service Repair Manual.pdfgen78guozun
The document provides instructions for removing and installing an engine. It is a multi-step process that begins by preparing the machine, disconnecting electrical and fluid connections, removing ancillary components, and then lifting the engine out of the machine. The installation process reverses these steps, carefully positioning and securing the engine before reconnecting all electrical and fluid lines. Safety is emphasized throughout with warnings about proper lifting and ensuring all personnel are clear during movements.
CASE IH STX325 Tractor Service Repair Manual.pdfgen78guozun
The document provides instructions for removing and installing an engine. It is a multi-step process that begins by preparing the machine, disconnecting electrical and fluid connections, removing ancillary components, and then lifting the engine out of the machine. The installation process reverses these steps, carefully positioning and securing the engine before reconnecting all electrical and fluid lines. Safety is emphasized throughout with warnings about proper lifting equipment and blocking the machine securely.
Caterpillar Cat 257 Multi Terrain Loader (Prefix CMM) Service Repair Manual (...gen78guozun
This document provides instructions for removing and installing various components of a 3034 engine, including:
- Removing the flywheel, which requires drilling holes in it and using guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller to avoid damaging the crankshaft.
- Installing the crankshaft rear seal by lubricating it and setting it in place with a seal installer tool.
- Removing the flywheel housing by detaching lifting brackets, removing bolts, and tapping it off dowels.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...gen78guozun
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
This document provides instructions for removing and installing a piston pump on a 246D Skid Steer Loader. It outlines the required tools and gives step-by-step instructions to disassemble and assemble the pump. To remove the pump, hoses and harnesses must be disconnected, then lifting tools are used to support the pump while bolts are removed. Reinstallation is the reverse of removal. Detailed illustrations accompany each step to show how to remove components like valves, seals, and housing pieces, and reinstall them in the proper order.
CASE IH STX275 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The goal is to fully separate the engine from other tractor components to allow for its removal from the vehicle. Safety precautions are advised when handling fluids, batteries, and heavy engine components.
1) The document provides instructions for removing and installing a lifter group on a C2.2 engine. It lists the required tool and removal steps, which include using a telescopic magnet to remove the lifters from the valve mechanism housing.
2) Installation instructions include cleaning components, lubricating the lifters, and inserting the lifters into the valve mechanism housing using the telescopic magnet. Proper lifter orientation is noted.
3) Completing the job involves installing the valve mechanism cover after checking lifter rotation.
The document provides instructions for removing and installing an exhaust manifold on a 249D Compact Track Loader powered by a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket, and removing any studs. For installation, clean surfaces are required, a new gasket is installed, the manifold is aligned and fastened, and bolts are tightened to the specified torque. The document also provides instructions for removing and installing valve springs, using the appropriate tools to compress springs at each step.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...gen78guozun
This document provides instructions for removing and installing the lift cylinder on a 247 Multi Terrain Loader. It lists the required tools and safety precautions. The removal procedure involves releasing hydraulic pressure, disconnecting hoses and removing pins and bolts to detach the cylinder. Reinstallation is the reverse of removal. Torque specifications are provided for reassembly.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
More Related Content
Similar to Caterpillar Cat 232D Skid Steer Loader (Prefix KXC) Service Repair Manual (KXC00001 and up).pdf
The document provides instructions for removing and installing a flywheel, crankshaft rear seal, flywheel housing, and vibration damper and pulley on a Caterpillar 320D2L excavator engine. The summary is:
1. The instructions describe removing bolts and tools to separate the flywheel, crankshaft rear seal, flywheel housing, and vibration damper and pulley from the engine.
2. Cleaning procedures and inspections for leaks are provided before reinstalling components.
3. Components are reinstalled by aligning parts, inserting bolts, and tightening to the specified torques.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting and replacing seals, installing dowels and gaskets, and tightening bolts to the specified torques.
This document provides instructions for installing a flywheel and crankshaft rear seal on a 320 GC excavator. It describes removing the flywheel, installing guide studs, positioning the flywheel onto the crankshaft, and tightening bolts while preventing rotation. It also details removing the crankshaft rear seal, ensuring surfaces are clean, and pushing a new seal onto the crankshaft before tightening screws in a specific sequence. The document gives similar instructions for removing and installing a wet back end flywheel housing.
This document provides instructions for installing a flywheel and crankshaft rear seal on a 320 GC excavator. It describes removing the flywheel, installing guide studs, positioning the flywheel onto the crankshaft, and tightening bolts while preventing rotation. It also details removing the crankshaft rear seal, ensuring surfaces are clean, and pushing a new seal onto the crankshaft before tightening screws in a specific sequence. The document gives similar instructions for removing and installing a wet back end flywheel housing.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
This service repair manual provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar C4.4 engine. It outlines the required tools and steps to remove and install the flywheel housing. The procedures include inspecting parts for leaks, aligning seals and gaskets, and torquing bolts to the specified values.
1) The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 320 GC excavator. It describes cleaning and preparing the components, using guide studs and lifting devices to position the heavy parts, and tightening bolts to the specified torques.
2) The instructions also cover removing and installing a wet back-end flywheel housing. This involves removing bolts and seals, cleaning surfaces, pressing in a new oil seal, and aligning dowels and gaskets before tightening bolts to graded torque values.
3) Tools, torque specifications, and safety precautions are provided to ensure correct disassembly and reassembly of the engine components.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 3054C engine. It describes the required tools and parts, cleaning requirements, installation procedures including torque specifications, and references other documents for additional information.
Similar to Caterpillar Cat 232D Skid Steer Loader (Prefix KXC) Service Repair Manual (KXC00001 and up).pdf (10)
CASE IH STX450 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The instructions cover disconnecting batteries, removing the radiator, hood, fuel lines, air intake components, and other parts to fully separate the engine from the tractor.
CASE IH STX440 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The instructions cover disconnecting batteries, removing the radiator, hood, fuel lines, air intake components, and other parts to fully separate the engine from the tractor.
CASE IH STX375 Tractor Service Repair Manual.pdfgen78guozun
The document provides instructions for removing and installing an engine. It is a multi-step process that begins by preparing the machine, disconnecting electrical and fluid connections, removing ancillary components, and then lifting the engine out of the machine. The installation process reverses these steps, carefully positioning and securing the engine before reconnecting all electrical and fluid lines. Safety is emphasized throughout with warnings about proper lifting and ensuring all personnel are clear during movements.
CASE IH STX325 Tractor Service Repair Manual.pdfgen78guozun
The document provides instructions for removing and installing an engine. It is a multi-step process that begins by preparing the machine, disconnecting electrical and fluid connections, removing ancillary components, and then lifting the engine out of the machine. The installation process reverses these steps, carefully positioning and securing the engine before reconnecting all electrical and fluid lines. Safety is emphasized throughout with warnings about proper lifting equipment and blocking the machine securely.
Caterpillar Cat 257 Multi Terrain Loader (Prefix CMM) Service Repair Manual (...gen78guozun
This document provides instructions for removing and installing various components of a 3034 engine, including:
- Removing the flywheel, which requires drilling holes in it and using guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller to avoid damaging the crankshaft.
- Installing the crankshaft rear seal by lubricating it and setting it in place with a seal installer tool.
- Removing the flywheel housing by detaching lifting brackets, removing bolts, and tapping it off dowels.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...gen78guozun
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
This document provides instructions for removing and installing a piston pump on a 246D Skid Steer Loader. It outlines the required tools and gives step-by-step instructions to disassemble and assemble the pump. To remove the pump, hoses and harnesses must be disconnected, then lifting tools are used to support the pump while bolts are removed. Reinstallation is the reverse of removal. Detailed illustrations accompany each step to show how to remove components like valves, seals, and housing pieces, and reinstall them in the proper order.
CASE IH STX275 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The goal is to fully separate the engine from other tractor components to allow for its removal from the vehicle. Safety precautions are advised when handling fluids, batteries, and heavy engine components.
1) The document provides instructions for removing and installing a lifter group on a C2.2 engine. It lists the required tool and removal steps, which include using a telescopic magnet to remove the lifters from the valve mechanism housing.
2) Installation instructions include cleaning components, lubricating the lifters, and inserting the lifters into the valve mechanism housing using the telescopic magnet. Proper lifter orientation is noted.
3) Completing the job involves installing the valve mechanism cover after checking lifter rotation.
The document provides instructions for removing and installing an exhaust manifold on a 249D Compact Track Loader powered by a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket, and removing any studs. For installation, clean surfaces are required, a new gasket is installed, the manifold is aligned and fastened, and bolts are tightened to the specified torque. The document also provides instructions for removing and installing valve springs, using the appropriate tools to compress springs at each step.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...gen78guozun
This document provides instructions for removing and installing the lift cylinder on a 247 Multi Terrain Loader. It lists the required tools and safety precautions. The removal procedure involves releasing hydraulic pressure, disconnecting hoses and removing pins and bolts to detach the cylinder. Reinstallation is the reverse of removal. Torque specifications are provided for reassembly.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims are used and bolts are tightened to the specified torques. Cleanliness of all fuel system components is emphasized to prevent contamination.
This document provides instructions for removing and installing the automatic timing advance and fuel injection pump housing & governor on a 245D Excavator with a 3406C diesel engine. It describes in detail the steps to take the components off the engine, including removing mounting bolts, nuts, hoses and other fasteners. The instructions note to cap or plug any openings immediately to prevent contamination. They also warn to use caution when removing certain parts like springs.
This document provides instructions for removing and installing various engine components on a 246 Skid Steer Loader, including the turbocharger, exhaust manifold, inlet manifold, and inlet and exhaust valve springs. The removal and installation procedures describe loosening clamps, removing bolts, plugging openings to prevent contamination, cleaning surfaces, and installing new gaskets. Tools required are also listed.
Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (...gen78guozun
This document provides instructions for disassembling and assembling starting motors for a 245B Series II excavator. It describes removing components like the rear housing, brush holder, pinion drive housing, and shift lever housing. Tools needed are listed. Detailed photos show each step, such as lifting brush springs, removing retaining rings, and cleaning parts with mineral spirits. Instructions are provided for both 42-MT and 37-MT/41-MT style starting motors.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes over 30 steps to disassemble the motors by removing components like the shuttle valve, pump head, body, barrel, pistons, and more. It then describes over 20 steps for reassembling the motors, providing details on cleaning parts, applying oil, pressing components, setting bearings, and checking clearance. The goal is to properly disassemble and reassemble the swing and track motors while identifying parts to ensure correct alignment during reassembly.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various bearings, gears, seals, tubes, and manifolds. The instructions specify cleaning all parts thoroughly and applying anti-seize compound before reassembling the swing drive using the reverse of the disassembly steps. Special tools are required and parts must be heated or cooled to specific temperatures during installation.
Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00001-00...gen78guozun
This document provides instructions for servicing components of a 245 Excavator's 3406 vehicular engine, including:
- Disassembling and reassembling the fuel injection pump housing, which involves removing various parts like pumps, racks, lifters, and bearings, and replacing them in the proper order.
- Removing and installing the inlet manifold, which connects to the cylinder head and air cleaner components.
- Removing the aftercooler unit, which involves disconnecting hoses and pipes, removing mounting bolts, and taking out the core component. Detailed steps are provided for each disassembly and reassembly process.
The document provides instructions for removing and installing the engine oil pump on a 242B2 Skid Steer Loader with a 3024C engine. The removal procedure involves removing the front housing, idler gear components, suction pipe, and idler hub. The installation procedure outlines installing the idler hub, gears, rotor, cover, and suction pipe and includes checking end play clearance. Safety notices are provided throughout regarding contained fluids, cleanliness, and spring loaded components.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 232D SKID STEER LOADER KXC
Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i06720081
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
B -
Guide Stud
(M10 x 1.25 mm by 80mm)
2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The three cylinder and the four cylinder engines have different flywheels. The removal
procedure is similar for all models.
1/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01305297
Typical example
1. Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel
is approximately 42 kg (93 lb).
2. Remove two bolts (1) from positions (X) on the flywheel.
3. Install Tooling (B) in positions (X) on the flywheel.
4. Remove the remaining bolts (1) and remove flywheel (2).
Note: On some three cylinder engines, a roll pin is located between the crankshaft and the
flywheel.
5. Inspect ring gear (3) and flywheel (2) for wear or damage. If the ring gear or the flywheel is
worn or damaged, use new parts for replacement.
2/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00825639
Typical example
6. To remove ring gear (3) from flywheel (2), place the flywheel on a suitable support. Use a
hammer (not shown) and a punch (4) to remove the ring gear from the flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 21:43:14 UTC+0800 2019
3/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 232D SKID STEER LOADER KXC
Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i06720105
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
B -
Guide Stud
(M10 x 1.25 mm by 80mm)
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1/4
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g01305341
Typical example
1. If the ring gear was removed, follow Steps 1.a through 1.c to install ring gear (3) to flywheel
(2).
a. Identify the orientation of the new ring gear to install the ring gear correctly onto the
flywheel.
Note: The chamfered side of gear teeth (Y) must face toward the starting motor when
the flywheel is installed to ensure the correct engagement of the starting motor.
b. Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to
installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that ring gear (3) is correctly oriented and quickly install the ring gear onto
flywheel (2).
2/4
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g01305297
Typical example
2. Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there
are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly,
"Crankshaft Rear Seal - Remove and Install".
3. Install Tooling (B) to positions (X) in the crankshaft.
4. Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel
is approximately 42 kg (93 lb).
5. On three cylinder engines with a roll pin, ensure that the roll pin is installed to the
crankshaft. Ensure that the roll pin is free from damage. Align the hole in the flywheel with
the roll pin in the crankshaft.
Position flywheel (2) onto Tooling (B).
6. Install bolts (1) finger tight.
7. Remove Tooling (B) and install the two remaining bolts (1).
8. Use a suitable tool to prevent flywheel (2) from rotating. Tighten bolts (1) to a torque of
74 N·m (54 lb ft).
9. Remove Tooling (A) and the lifting device from the flywheel.
End By:
3/4
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 21:44:13 UTC+0800 2019
4/4
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 232D SKID STEER LOADER KXC
Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i07360167
Crankshaft Rear Seal - Remove and Install
SMCS - 1161-010
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: The three cylinder and the four cylinder engines have different configurations for the
flywheel housing and the back plate. The removal process is similar for all models.
1/4
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g01305376
Typical example
1. Remove bolts (3) and remove the flywheel housing or back plate (2) from the cylinder
block. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for
more information.
2. Remove crankshaft rear seal (1) from the cylinder block. Discard the crankshaft oil seal.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9612 Silicone Sealant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g01305365
Typical example
1. Ensure the mating surface of cylinder block (5) and the flywheel housing or back plate (2)
are clean and free from damage. Inspect dowels (4). If the dowels are damaged, use new
parts for replacement.
2. Ensure that crankshaft flange (6) is clean and free from damage. A crankshaft flange that
has a worn seal surface, or a damaged seal surface can be reclaimed by installing a wear
sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve (Rear) - Remove and
Install" for more information.
3. Apply clean engine lubricating oil to the flange of crankshaft (6) around the running surface
of crankshaft rear seal.
4. Align a new crankshaft rear seal (1) with the flange of crankshaft (6). Carefully install
crankshaft rear seal (1) onto the crankshaft flange.
5. Apply a continuous bead of Tooling (A) to the rear face of the cylinder block around the
edge of crankshaft rear seal (1). Apply a continuous bead of Tooling (A) around plug (X).
3/4
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 6. Align the flywheel housing or back plate (2) to dowels (4). Install the flywheel housing or
back plate (2) and install bolts (3) to cylinder block (5). Refer to Disassembly and
Assembly, "Flywheel Housing - Remove and Install" for more information.
7. Tighten bolts (3).
For the C1.1 engine, tighten the bolts to a torque of 50 N·m (37 lb ft).
For C1.5 and C2.2 engines, tighten the bolts to a torque of 25 N·m (221 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 21:45:12 UTC+0800 2019
4/4
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 232D SKID STEER LOADER KXC
Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i06042230
Crankshaft Wear Sleeve (Rear) - Remove and Install
SMCS - 1161-010-ZV
Removal Procedure
Start By:
a. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal - Remove and Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves
are not original equipment.
1/6
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g03786380
Sectional view of the crankshaft and of the crankshaft wear sleeve
1. Use a suitable sharp tool to score a deep line across crankshaft wear sleeve (1).
Note: Some crankshaft wear sleeves may have a flange. Take care to avoid damaging the
crankshaft.
2. Insert a thin blade between crankshaft wear sleeve (1) and crankshaft (2) below the scored
line. The crankshaft wear sleeve will separate along the line.
3. Remove crankshaft wear sleeve (1) from crankshaft (2). Discard the crankshaft wear sleeve.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8846 Gasket Maker 1
NOTICE
2/6
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the crankshaft is thoroughly clean and dry. Remove any areas of raised damage.
Illustration 2 g03786381
Sectional view of the wear sleeve
3/6
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 3 g03786382
Sectional view of the crankshaft, the wear sleeve, and the installation tool
4/6
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g03786398
2. Apply a small continuous bead of Tooling (A) to the inner surface of crankshaft wear sleeve
(1) at position X. Apply the bead of Tooling (A) 5.00 mm (0.2 inch) from the flange end of
the crankshaft wear sleeve.
3. Align crankshaft wear sleeve (1) with crankshaft (2). Position installation tool (3) that is
provided with the crankshaft wear sleeve over the crankshaft. Use a hammer to drive the
crankshaft wear sleeve onto the crankshaft. Ensure that dimension (Y) is 6.5 mm
(0.26 inch).
Note: Dimension (Y) is the distance from the edge of the crankshaft wear sleeve from the
rear face of the crankshaft.
4. Remove installation tool (3).
5. Use a suitable tool to cut down to Scored Line (Z) on crankshaft wear sleeve (1) and remove
the curved section of the crankshaft wear sleeve.Ensure that the crankshaft rear seal
5/6
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. surface of the crankshaft wear sleeve is not distorted or damaged as the curved section
of the crankshaft wear sleeve is removed.
Note: Ensure that the crankshaft wear sleeve has no rough edges, if crankshaft wear sleeve
has rough edges use suitable tooling to clean the rough edges.
End By:
a. Install a new crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal - Remove and Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 21:46:11 UTC+0800 2019
6/6
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 232D SKID STEER LOADER KXC
Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i02602665
Flywheel Housing - Remove and Install - Engines with
Flywheel Housing and Back Plate
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Support the engine.
2. Install a suitable lifting device to the flywheel housing. Support the weight of the housing.
The weight of the flywheel housing is approximately 30 kg (66 lb).
1/5
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Illustration 2 g01305649
Typical example
3. Remove bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block.
4. Remove bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8)
to the cylinder block.
5. Remove bolts (1) that fasten back plate (2) to flywheel housing (8).
6. Remove nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing
(8).
7. Carefully remove flywheel housing (8) from back plate (2) and dowels (7). Use a suitable
lifting device to remove the flywheel housing.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 1. Ensure that the mating surfaces of back plate (2) and flywheel housing (8) are clean and free
from damage. Inspect the crankshaft rear seal (not shown) for leaks. If necessary, replace
the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal -
Remove and Install" for the correct procedure. Inspect dowels (7) for damage. If the dowels
are damaged, use new parts for replacement.
Illustration 3 g01305649
4/5
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 4 g01326591
Typical example
2. Use a suitable lifting device to align flywheel housing (8) to dowels (7). The weight of the
flywheel housing is approximately 30 kg (66 lb). Install the flywheel housing to the back
plate.
3. Install nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing (8).
4. Install bolts (1) that fasten back plate (2) to flywheel housing (8).
5. Install bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8)
to the cylinder block.
6. Remove the lifting device from the flywheel housing.
7. Install bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block.
8. Tighten the fasteners to a torque of 25 N·m (19 lb ft).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 21:47:11 UTC+0800 2019
5/5
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 232D SKID STEER LOADER KXC
Configuration: 232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Media Number -KENR6948-06 Publication Date -01/06/2015 Date Updated -02/08/2018
i06721519
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The three cylinder and the four cylinder engines have different flywheel housings. The
removal procedure is similar for all models.
1. Support the engine.
2. Install a suitable lifting device to the flywheel housing. Support the weight of the housing.
The weight of the flywheel housing is approximately 30 kg (66 lb).
1/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g01305734
Typical example
3. Remove bolts (1) that fasten flywheel housing (2) to the cylinder block.
4. Use the lifting device to remove flywheel housing (2) from the engine.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 2 g01326595
Typical example
1. Ensure the mating surfaces of flywheel housing (2) are clean and free from damage. Inspect
the crankshaft rear seal (3) for leaks. If necessary, replace the crankshaft rear seal. Refer to
Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct
procedure. Inspect dowels (4) for damage. If the dowels are damaged, use new parts for
replacement.
2. Use a suitable lifting device to align flywheel housing (2) to dowels (5) and install the
flywheel housing. The weight of the flywheel housing is approximately 30 kg (66 lb).
3. Install bolts (1). Tighten the bolts to a torque of 25 N·m (19 lb ft).
4. Remove the lifting device from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 3 21:48:10 UTC+0800 2019
3/3
232D Skid Steer Loader KXC00001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...