This document provides instructions for removing and installing inlet and exhaust valve guides on a 213B excavator. The removal procedure involves using a valve guide driver tool to remove the guides from the cylinder head. For installation, the guides are tapped into position in the cylinder head and driven fully into place using the driver tool along with a guide collar. Proper cleaning is important to prevent contaminants from causing premature wear. Reusability guidelines should be followed for the valve guides.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...f8usejkdmmd8i
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process including inserting an extractor tool into the valve seat, expanding the tool to remove the seat, and installing a new seat by tapping it into place in the cylinder head. Safety notices are provided to keep parts clean and contain fluids during the repair work.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...tengtui535
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Precautions are given to keep parts clean and refer to other documents for guidance on reusable components.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...ze6074xunong
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Precautions are given to keep parts clean and refer to other documents for guidance on reusable components.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...hdjsjndndnd
This document provides instructions for removing and installing inlet and exhaust valve seats in a Caterpillar 3116 engine. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Proper cleaning and lubrication of parts is emphasized to prevent premature wear and failure of components. Relevant guidelines for determining if removed parts can be reused are also referenced.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...f8seodkdmdmed3
This document provides instructions for installing an inlet manifold on a 214B FT excavator engine. It describes:
1) Cleaning and positioning a new gasket on the cylinder head and installing the air inlet manifold with bolts.
2) Installing air inlet elbows and connecting the air inlet heater solenoid.
3) Completing the installation by reattaching the valve mechanism cover.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...ifoseidkkd
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...f8usejkdmmd8i
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process including inserting an extractor tool into the valve seat, expanding the tool to remove the seat, and installing a new seat by tapping it into place in the cylinder head. Safety notices are provided to keep parts clean and contain fluids during the repair work.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...tengtui535
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Precautions are given to keep parts clean and refer to other documents for guidance on reusable components.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...ze6074xunong
This document provides instructions for removing and installing inlet and exhaust valve seats in a cylinder head. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Precautions are given to keep parts clean and refer to other documents for guidance on reusable components.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...hdjsjndndnd
This document provides instructions for removing and installing inlet and exhaust valve seats in a Caterpillar 3116 engine. It outlines the required tools and gives a step-by-step process that involves using a valve seat extractor tool to remove the old seats and install new ones. Proper cleaning and lubrication of parts is emphasized to prevent premature wear and failure of components. Relevant guidelines for determining if removed parts can be reused are also referenced.
Caterpillar Cat 214B and 214B FT EXCAVATOR (Prefix 9MF) Service Repair Manual...f8seodkdmdmed3
This document provides instructions for installing an inlet manifold on a 214B FT excavator engine. It describes:
1) Cleaning and positioning a new gasket on the cylinder head and installing the air inlet manifold with bolts.
2) Installing air inlet elbows and connecting the air inlet heater solenoid.
3) Completing the installation by reattaching the valve mechanism cover.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...ifoseidkkd
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert to remove it from the cylinder head. New valve seat inserts are then installed by tapping them into place in the cylinder head. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...ifoseidkkd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert to remove it from the cylinder head. New valve seat inserts are then installed by tapping them into place in the cylinder head. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fjskkmemem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...JayHaines2
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for specifications on reusable components. The document is from a service repair manual for excavator and engine models.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts. The process includes removing any remaining valves first before pressing new guides into place and ensuring they are flush with the cylinder head.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...fjskkmemem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...JayHaines2
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety notices are provided to keep parts clean and contain fluids during repair work.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on Caterpillar 325, 325L and 325LN excavator models. The procedure includes using specific tools to extract the valve seat inserts from the cylinder head. New valve seat inserts should be installed and lubricated before reinstalling the valves and valve guides. Safety precautions are provided to keep parts clean and contain fluids during the repair process.
This document provides disassembly and assembly instructions for the transmission of a D6R track-type tractor. It details removing and installing over 80 individual parts. Key steps include separating the transmission from the bevel gear, removing the planetary group and transmission cover, and disassembling the individual clutch housings, gears, shafts, and carriers. Proper inspection and cleaning of parts is noted.
This document provides instructions for disassembling and assembling the final drive of a D6R track-type tractor. The disassembly procedure involves using various tools to remove 19 different components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and includes precautions for installing seals and bearings correctly.
More Related Content
Similar to Caterpillar Cat 213B EXCAVATOR (Prefix 1EJ) Service Repair Manual (1EJ00001 and up).pdf
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert to remove it from the cylinder head. New valve seat inserts are then installed by tapping them into place in the cylinder head. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...ifoseidkkd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert to remove it from the cylinder head. New valve seat inserts are then installed by tapping them into place in the cylinder head. Safety precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...fjskkmemem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 a excavator (prefix 6 rm) service repair manual (6rm00001...JayHaines2
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are listed to keep parts clean and refer to other documents for specifications on reusable components. The document is from a service repair manual for excavator and engine models.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...fujsekksmem
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts. The process includes removing any remaining valves first before pressing new guides into place and ensuring they are flush with the cylinder head.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...fjskkmemem
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and replace them if needed. Precautions are given to keep parts clean and refer to other documents for guidance on determining if parts can be reused. The document is from a service repair manual for the excavator model.
Caterpillar cat 325 l excavator (prefix 6rm) service repair manual (6rm00001 ...JayHaines2
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a Caterpillar 325-A excavator. It outlines the required tools and gives a step-by-step process that includes using a valve seat extractor tool to expand below the edge of the valve seat insert and remove it from the cylinder head. New valve seat inserts should be installed using the same basic process in reverse. Safety notices are provided to keep parts clean and contain fluids during repair work.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on Caterpillar 325, 325L and 325LN excavator models. The procedure includes using specific tools to extract the valve seat inserts from the cylinder head. New valve seat inserts should be installed and lubricated before reinstalling the valves and valve guides. Safety precautions are provided to keep parts clean and contain fluids during the repair process.
Similar to Caterpillar Cat 213B EXCAVATOR (Prefix 1EJ) Service Repair Manual (1EJ00001 and up).pdf (20)
This document provides disassembly and assembly instructions for the transmission of a D6R track-type tractor. It details removing and installing over 80 individual parts. Key steps include separating the transmission from the bevel gear, removing the planetary group and transmission cover, and disassembling the individual clutch housings, gears, shafts, and carriers. Proper inspection and cleaning of parts is noted.
This document provides instructions for disassembling and assembling the final drive of a D6R track-type tractor. The disassembly procedure involves using various tools to remove 19 different components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and includes precautions for installing seals and bearings correctly.
The document provides instructions for removing and installing final drives on a D6R track-type tractor. It describes:
1) Removing the final drives which involves draining oil, removing mounting bolts and hardware, and lifting the drive out.
2) Disassembling the final drives by removing planetary carriers, gears, shafts, seals, and other components.
3) Assembling the final drives by reversing the disassembly steps and ensuring proper installation of seals, gears, carriers, and mounting hardware.
4) Reinstalling the final drives by lifting them into place, inserting mounting bolts and hardware, and refilling with oil.
This document provides instructions for removing and disassembling a final drive from a D6R track-type tractor, as well as assembling a final drive. Key steps include using specialized tools to remove the final drive and axle, disassembling internal components like planetary gears and carriers, and precisely installing seals and bearings during assembly. Safety notices warn of risks like uncontrolled machine movement if brakes are ineffective during removal.
This document provides instructions for disassembling and assembling the torque divider of a D6R track-type tractor. It describes removing and installing over 30 different components of the torque divider. Key steps include using tools and hoists to remove large components like the torque divider housing weighing 145 kg, and precisely measuring clearances between components like the stator and turbine wheel to be between 1.76 to 1.94 mm. Reassembly involves installing bearings and seals, heating components, and torquing bolts to specified values.
This document provides instructions for disassembling and assembling the bevel and transfer gears of a D6R track-type tractor. It describes removing over 30 individual components in 26 steps, including the transmission gears, bearings, seals, and housings. Reassembly is outlined in 38 steps, with specifics on heating and installing bearings, applying sealant, adjusting end play and backlash using shims and gauges, and torquing bolts. The document is highly technical and aimed at mechanics performing gearbox maintenance and repairs.
This document provides instructions for disassembling and assembling the swing drive of an excavator model 558. It details 25 steps for disassembly, removing components like gears, shafts, seals and housings. It notes cleaning and inspecting parts before assembly. The assembly section lists 13 steps to reinstall components in reverse order, applying compounds and ensuring cleanliness. Special tools are listed to aid in removal and installation of heavy components weighing up to 510kg. Safety precautions are provided to contain fluids and protect personnel.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...hdjsjndndnd
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and drivers. Safety notices are provided regarding contained fluids, spring force, and being struck by parts.
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include:
1) Draining oil from the final drive and removing covers, axles, and bolts holding components in place.
2) Using lifting tools and hoists to remove heavy components like final drives weighing over 600 kg.
3) Inspecting seals and bearings during disassembly and applying clean oil during assembly.
4) Heating and pressing bearings and seals into place during reassembly and torquing bolts to specified values.
Caterpillar Cat 390D L Excavator (Prefix WBT) Service Repair Manual (WBT00001...hdjsjndndnd
This document provides disassembly and assembly instructions for the travel motor on a 390D L excavator. It describes 40 steps to disassemble the travel motor, removing components like the head, relief valves, pistons, springs, seals and bearings. It then describes 3 steps to begin reassembling the travel motor, starting with installing the lip seal, bearing and retaining ring. Detailed illustrations are provided for each step. Cleanliness and applying lubricant to parts are emphasized during disassembly and assembly.
Caterpillar Cat 385C L Excavator (Prefix KKK) Service Repair Manual (KKK00001...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It begins with a list of required tools. The disassembly procedure has 33 steps that remove components like the housing cover, carrier assemblies, planetary gears, ring gear, and seals. The assembly procedure has 17 steps that install components in reverse order, noting the importance of cleanliness and applying lubricants where specified.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix JDL) Service Repair Manual...hdjsjndndnd
The document provides instructions for disassembling and assembling the final drive of a D6R III track-type tractor. The disassembly procedure involves 19 steps to remove components such as the planetary carrier, gears, seals, and hub. The assembly procedure describes 15 steps including pressing components, installing seals and bearings at specified temperatures, and torquing bolts to the correct specifications. Proper cleaning, lubrication, and use of specialized tools are emphasized to correctly perform the processes.
The document provides instructions for disassembling and assembling the travel motor of a 385C Excavator. It lists 40 steps for disassembly, including removing the head, relief valves, spools, pistons, springs, port plate, and other internal components. It then lists 16 steps for reassembly, starting with installing internal seals and moving outward to reinstalling the piston, port plate, spools, and head. Precautions are provided regarding cleaning parts, applying oil, and ensuring proper alignment of components.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix HCD) Service Repair Manual...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive components of a Caterpillar D6R III track-type tractor. The disassembly process involves using various tools to remove 19 components including planetary gears, bearings, seals, and hubs. The assembly process similarly uses tools to reinstall the components in the reverse order, taking care to clean parts and apply oil, and heat or cool components as needed to ensure proper installation. Special installation procedures are specified for seals and bearings.
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It begins with a list of required tools. The disassembly procedure has 33 steps that remove components like the housing cover, carrier assemblies, planetary gears, ring gear, and seals. The assembly procedure has 17 steps that install components in reverse order, noting the importance of cleanliness and applying lubricants where specified.
This document provides instructions for disassembling the control valve for the attachment, bucket, boom, right travel, left travel, and stick systems of a 385B Excavator. It outlines 25 steps to disassemble the various components of the control valve, including removing covers, seals, valves, pistons, solenoids, manifolds, and other parts. Precautions are provided to watch out for spring forces and to keep components clean during disassembly. Tools required include pliers. The goal is to disassemble the control valve into its individual parts to allow for inspection and replacement of any worn components.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix FDT) Service Repair Manual ...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. The disassembly process involves using various tools to remove 19 different parts from the final drive assembly, including the planetary carrier, gears, seals, and hub. The assembly process describes 16 steps for reinstalling the parts in reverse order and includes safety notices and requirements for cleaning, lubricating, and heating components.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BRJ) Service Repair Manual ...hdjsjndndnd
The document provides instructions for disassembling the transmission of a D6R II track-type tractor. It lists the required tools and gives step-by-step instructions to remove components such as tubes, valves, gears, housings, pistons, seals, and plates. Special care must be taken to keep parts like discs and plates organized according to their clutch assemblies. Dismantling involves using lifting devices and compression tools to handle heavy internal components.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BLE) Service Repair Manual ...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. The disassembly procedure involves using various tools to remove 19 parts from the final drive assembly, including the planetary carrier, gears, seals, and hub. The assembly procedure describes 16 steps for installing the parts in reverse order, noting the importance of cleanliness and applying oil during assembly. Torque specifications and heating instructions are provided for certain bolts and bearings.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BMK) Service Repair Manual ...hdjsjndndnd
The document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. It describes in detail how to remove and install components such as the planetary carrier, hub, ring gear, and seals using the proper tools. Cleanliness is emphasized throughout the process to prevent dirt from entering parts. Proper bearing installation and torque specifications are also outlined to ensure correct assembly.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:20:07 UTC+0800 2021
2/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:21:03 UTC+0800 2021
5/5
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:21:58 UTC+0800 2021
4/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:22:54 UTC+0800 2021
4/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:23:50 UTC+0800 2021
2/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:24:46 UTC+0800 2021
2/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:25:41 UTC+0800 2021
2/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 2 g01185803
Illustration 3 g00676791
1. Position the gasket and engine oil filter base (4) on the cylinder block.
2. Install the washers and bolts (2) that hold engine oil filter base (4) to the cylinder block.
Tighten the bolts according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Apply lubricant to new O-ring seal (5) . Install O-ring seal (5) in the fitting on the engine oil
filter base.
4. Connect tube assembly (1) to engine oil filter base (4) .
Note: Never install an oil filter with a wrench. Follow the instructions on the oil filter.
2/3
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. 5. Put a coat of fresh oil on the O-ring seal for the engine oil filter. Install engine oil filter (3)
on engine oil filter base (4) by hand.
6. After the O-ring seal contacts engine oil filter base (4) , turn engine oil filter (3) for 3/4 of a
turn.
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:26:37 UTC+0800 2021
3/3
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943853
Engine Oil Filter Bypass Valve - Remove and Install
SMCS - 1308-010-BV
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 1 g00630032
Illustration 2 g00629985
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plug (1) and the O-ring seal from the engine oil filter base.
2. Remove valve spring (2) and bypass valve (3) from the engine oil filter base.
Installation Procedure
NOTICE
2/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00630032
Illustration 4 g00629985
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Inspect the condition of the O-ring seal. Replace the seal, if necessary.
2. Install bypass valve (3) and valve spring (2) in the engine oil filter base.
3/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. 3. Install plug (1) in the engine oil filter base.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:27:33 UTC+0800 2021
4/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
30. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
31. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01944039
Engine Oil Cooler Bypass Valve - Remove and Install
SMCS - 1314-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
32. Illustration 1 g00629979
Illustration 2 g00629985
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plug (1) and the O-ring seal from the engine oil cooler.
2. Remove valve spring (2) and bypass valve (3) from the engine oil cooler.
Installation Procedure
NOTICE
2/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
33. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00629985
Illustration 4 g00629979
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Inspect the condition of the O-ring seal. Replace the seal, if necessary.
2. Install bypass valve (3) and valve spring (2) in the engine oil cooler.
3/4
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...