The document provides instructions to remove the rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It describes draining fluids, removing mounting bolts and plates, and lifting out the assembly using lifting brackets and eyes. Tools required include brackets, a retainer, lifting eyes, and a sprocket guide. The assembly should be cleaned of contaminants before installation.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjsekdmme
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...dujjsjekkkdmm
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fusjejedrfjskekem
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjskekdmem
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjsefkkertsemme
This document provides instructions for assembling and disassembling a service brake and wheel spindle on a Caterpillar 18M3 motor grader. It outlines 30 steps for assembly, which include installing seals, discs, springs, bearings and other components. Removal instructions are also given for draining oil from the grader's tandem housing and removing parts like fenders, walkways and bolts. Tools required are listed.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...ze6074xunong
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure outlines installing these components in reverse order and notes to keep parts clean and check seals for wear.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, plates and bearings. The assembly procedure lists 21 steps for installing these components in reverse order and includes safety notices for spring loaded parts. Installation involves attaching hoses, brackets and bolting the 52 kg pump into place on the grader.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure lists 21 steps for installing the components in reverse order. Safety notices are included to warn of potential injury from spring loaded parts.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjsekdmme
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...dujjsjekkkdmm
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fusjejedrfjskekem
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjskekdmem
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjsefkkertsemme
This document provides instructions for assembling and disassembling a service brake and wheel spindle on a Caterpillar 18M3 motor grader. It outlines 30 steps for assembly, which include installing seals, discs, springs, bearings and other components. Removal instructions are also given for draining oil from the grader's tandem housing and removing parts like fenders, walkways and bolts. Tools required are listed.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...ze6074xunong
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure outlines installing these components in reverse order and notes to keep parts clean and check seals for wear.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, plates and bearings. The assembly procedure lists 21 steps for installing these components in reverse order and includes safety notices for spring loaded parts. Installation involves attaching hoses, brackets and bolting the 52 kg pump into place on the grader.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure lists 21 steps for installing the components in reverse order. Safety notices are included to warn of potential injury from spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...jkdkkdsmmd
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting all hoses and brackets. Safety notices are provided regarding contained fluids and spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...idksmmdmdm
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting all hoses and brackets. Safety notices are provided regarding contained fluids and spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...hean57759707
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting the hoses, harnesses and brackets. Safety notices are provided regarding contained fluids and wearing protective equipment when working with pressurized components.
Caterpillar cat 160 m 3 awd motor grader (prefix n9k) service repair manual (...fjjsekkskeoelkm
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 160M 3 AWD motor grader. It lists the required tools and gives step-by-step instructions for removing and installing various components of the piston pump like valves, springs, seals, pistons, plates and covers. Safety precautions are provided to prevent injury from parts under spring tension. The instructions are intended to guide maintenance and repair of the motor grader's hydraulic and steering systems.
Caterpillar cat 160 m 3 awd motor grader (prefix n9k) service repair manual (...fksefkskemm
This service repair manual provides instructions for disassembling and assembling the piston pump on a Caterpillar 160M 3 AWD motor grader. It lists the required tools and presents 18 steps for disassembly that include removing valves, seals, springs, spools and plugs. The 20 steps for assembly include installing these same components in reverse order as well as ensuring parts are clean and seals are in good condition. Installation involves attaching lifting and connecting hoses, harnesses and brackets.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...f8usejkdmmd8i
The document provides assembly and disassembly instructions for a piston motor and gear motor used in the hydraulic fan system of a Caterpillar 160M 3 motor grader. It includes 38 steps to assemble the piston motor, installing various seals, springs, bearings and other components. It also includes 7 steps to disassemble the gear motor, removing seals, gears, bearings and other parts. The instructions are accompanied by illustrations and require various specialty tools to correctly assemble and disassemble the hydraulic fan motors.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...tengtui535
The document provides assembly and disassembly instructions for a piston motor (hydraulic fan) and gear motor (hydraulic fan) used in a Caterpillar 160M 3 motor grader. It details 38 steps for piston motor assembly requiring various tools. It also details 7 steps for gear motor disassembly and 7 steps for assembly, requiring retaining ring pliers. The instructions include illustrations and specify tightening bolts to 140 N·m.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...f8seodkdmdmed3
The document provides assembly and disassembly instructions for a piston motor (hydraulic fan) and gear motor (hydraulic fan) used in a Caterpillar 160M 3 motor grader. It details 38 steps for piston motor assembly requiring various tools. It also details 7 steps for gear motor disassembly and 7 steps for assembly, requiring retaining ring pliers. The instructions are part of a service repair manual for motor grader systems.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...ze6074xunong
The document provides assembly and disassembly instructions for a piston motor and gear motor used in the hydraulic fan system of a Caterpillar 160M 3 motor grader. It includes 38 steps to assemble the piston motor, installing various seals, springs, bearings and other components. It also includes 7 steps to disassemble the gear motor, removing seals, gears, bearings and other parts. The instructions are accompanied by illustrations and require various specialty tools to correctly assemble and disassemble the hydraulic fan motors.
Massey Ferguson MF2620 TRACTOR (- 271213) Parts Catalogue Manual.pdfvvnj41316031
The document contains parts lists and technical specifications for components of a Massey Ferguson MF 2620 tractor, including the engine, cylinder block, flywheel housing, crankshaft, pistons, connecting rods, and cylinder head. Each component lists the relevant part numbers, quantities, descriptions, and any additional comments. Serial numbers and engine numbers are referenced for certain part applicability.
KOBELCO 140SRLC-3 HYDRAULIC EXCAVATOR Service Repair Manual.pdfvvnj41316031
This service manual provides instructions for maintenance, repair, and troubleshooting of a Kobelco 140SRLC-3 hydraulic excavator. It begins with general safety information and precautions for working on the machine. The manual is divided into 7 sections covering specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and optional attachments. Technicians are advised to thoroughly read and understand the contents before working on the excavator to prevent accidents and ensure proper repair.
KOBELCO 70SR-2 Acera Hydraulic Excavator Service Repair Manual.pdfvvnj41316031
The document is a service manual that provides instructions for disassembling a pilot valve used in a Kobelco Construction Machinery hydraulic excavator model 70SR-2 Acera. It includes diagrams of the valve components and specifies tightening torques. The disassembly instructions describe removing external components like boots and nuts, then internal parts like springs, spools and seals while taking safety precautions for any stored energy in the valve springs.
KOBELCO 17SR-Tier 4 Hydraulic Excavator Service Repair Manual.pdfvvnj41316031
This document provides guidelines and safety precautions for repairing hydraulic excavators. It covers preparing for disassembly, safety during disassembly and assembly, working with hydraulic equipment and electrical components, handling hydraulic parts, welding repairs, and an international unit conversion system. Technicians are instructed to thoroughly read manuals, use proper tools, relieve pressures, and take caution with hot or heavy components. Protective equipment is recommended.
The document provides instructions for disassembling and assembling the front axle of a M322D MH Wheeled Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the carrier housing, planetary gears, bearings, seals, and brake discs. Reassembly instructions are also provided, with steps like installing bearings, seals, and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant and ensuring proper torque specifications are followed for nuts and bolts. Cleanliness and use of the correct tools are emphasized throughout.
This document provides disassembly instructions for the front and rear axles, carriers, hubs, and brakes of an M322C wheeled excavator. The front axle disassembly procedure involves 41 steps to remove components like the carrier housing, planetary gears, ring gear assembly, hub assembly, and spindle components. The rear axle disassembly involves 27 steps including removing the brake drum, gear assemblies, axle, hub assembly, dust shield, brake assembly, and spindle. Detailed illustrations are provided to identify each part and tooling required is listed.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then provides 29 steps to reassemble the swing drive, installing the components in reverse order and noting that all seals and gaskets must be replaced. Precise torques and clear illustrations are provided to ensure correct assembly.
This document provides instructions for disassembling and assembling the swing drive of an M318D MH wheeled excavator. The disassembly procedure involves using various tools to remove 28 individual parts from the swing drive assembly, including gears, bearings, seals, and housing components. The assembly procedure similarly uses tools to install the parts in reverse order and includes steps to properly set bearing preloads. Precautions are listed regarding cleaning parts and applying lubricant before assembly.
This document provides instructions for disassembling and assembling the swing drive of an M318C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant to components and ensuring proper torque specifications are achieved. Tools and safety precautions are also listed.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the rear axle of a M316C Wheeled Excavator. The disassembly procedure involves removing 23 components of the rear axle including the carrier housing, planetary gears, retaining rings, and hub. The assembly procedure describes installing these 23 components in reverse order and includes steps to measure clearances and install seals, bearings, and thrust washers correctly. Tools required are also listed.
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves using various tools to remove 28 individual parts from the swing drive housing. The assembly procedure similarly uses tools to install the parts in reverse order, noting that bearings and seals must be heated or cooled as needed and lubricated before installation. Precise torques are specified for tightening critical nuts to properly set bearing preloads.
More Related Content
Similar to Caterpillar Cat 18M3 MOTOR GRADER (Prefix N9A) Service Repair Manual (N9A00001 and up).pdf
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...jkdkkdsmmd
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting all hoses and brackets. Safety notices are provided regarding contained fluids and spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...idksmmdmdm
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting all hoses and brackets. Safety notices are provided regarding contained fluids and spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...hean57759707
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting the hoses, harnesses and brackets. Safety notices are provided regarding contained fluids and wearing protective equipment when working with pressurized components.
Caterpillar cat 160 m 3 awd motor grader (prefix n9k) service repair manual (...fjjsekkskeoelkm
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 160M 3 AWD motor grader. It lists the required tools and gives step-by-step instructions for removing and installing various components of the piston pump like valves, springs, seals, pistons, plates and covers. Safety precautions are provided to prevent injury from parts under spring tension. The instructions are intended to guide maintenance and repair of the motor grader's hydraulic and steering systems.
Caterpillar cat 160 m 3 awd motor grader (prefix n9k) service repair manual (...fksefkskemm
This service repair manual provides instructions for disassembling and assembling the piston pump on a Caterpillar 160M 3 AWD motor grader. It lists the required tools and presents 18 steps for disassembly that include removing valves, seals, springs, spools and plugs. The 20 steps for assembly include installing these same components in reverse order as well as ensuring parts are clean and seals are in good condition. Installation involves attaching lifting and connecting hoses, harnesses and brackets.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...f8usejkdmmd8i
The document provides assembly and disassembly instructions for a piston motor and gear motor used in the hydraulic fan system of a Caterpillar 160M 3 motor grader. It includes 38 steps to assemble the piston motor, installing various seals, springs, bearings and other components. It also includes 7 steps to disassemble the gear motor, removing seals, gears, bearings and other parts. The instructions are accompanied by illustrations and require various specialty tools to correctly assemble and disassemble the hydraulic fan motors.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...tengtui535
The document provides assembly and disassembly instructions for a piston motor (hydraulic fan) and gear motor (hydraulic fan) used in a Caterpillar 160M 3 motor grader. It details 38 steps for piston motor assembly requiring various tools. It also details 7 steps for gear motor disassembly and 7 steps for assembly, requiring retaining ring pliers. The instructions include illustrations and specify tightening bolts to 140 N·m.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...f8seodkdmdmed3
The document provides assembly and disassembly instructions for a piston motor (hydraulic fan) and gear motor (hydraulic fan) used in a Caterpillar 160M 3 motor grader. It details 38 steps for piston motor assembly requiring various tools. It also details 7 steps for gear motor disassembly and 7 steps for assembly, requiring retaining ring pliers. The instructions are part of a service repair manual for motor grader systems.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...ze6074xunong
The document provides assembly and disassembly instructions for a piston motor and gear motor used in the hydraulic fan system of a Caterpillar 160M 3 motor grader. It includes 38 steps to assemble the piston motor, installing various seals, springs, bearings and other components. It also includes 7 steps to disassemble the gear motor, removing seals, gears, bearings and other parts. The instructions are accompanied by illustrations and require various specialty tools to correctly assemble and disassemble the hydraulic fan motors.
Similar to Caterpillar Cat 18M3 MOTOR GRADER (Prefix N9A) Service Repair Manual (N9A00001 and up).pdf (9)
Massey Ferguson MF2620 TRACTOR (- 271213) Parts Catalogue Manual.pdfvvnj41316031
The document contains parts lists and technical specifications for components of a Massey Ferguson MF 2620 tractor, including the engine, cylinder block, flywheel housing, crankshaft, pistons, connecting rods, and cylinder head. Each component lists the relevant part numbers, quantities, descriptions, and any additional comments. Serial numbers and engine numbers are referenced for certain part applicability.
KOBELCO 140SRLC-3 HYDRAULIC EXCAVATOR Service Repair Manual.pdfvvnj41316031
This service manual provides instructions for maintenance, repair, and troubleshooting of a Kobelco 140SRLC-3 hydraulic excavator. It begins with general safety information and precautions for working on the machine. The manual is divided into 7 sections covering specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and optional attachments. Technicians are advised to thoroughly read and understand the contents before working on the excavator to prevent accidents and ensure proper repair.
KOBELCO 70SR-2 Acera Hydraulic Excavator Service Repair Manual.pdfvvnj41316031
The document is a service manual that provides instructions for disassembling a pilot valve used in a Kobelco Construction Machinery hydraulic excavator model 70SR-2 Acera. It includes diagrams of the valve components and specifies tightening torques. The disassembly instructions describe removing external components like boots and nuts, then internal parts like springs, spools and seals while taking safety precautions for any stored energy in the valve springs.
KOBELCO 17SR-Tier 4 Hydraulic Excavator Service Repair Manual.pdfvvnj41316031
This document provides guidelines and safety precautions for repairing hydraulic excavators. It covers preparing for disassembly, safety during disassembly and assembly, working with hydraulic equipment and electrical components, handling hydraulic parts, welding repairs, and an international unit conversion system. Technicians are instructed to thoroughly read manuals, use proper tools, relieve pressures, and take caution with hot or heavy components. Protective equipment is recommended.
The document provides instructions for disassembling and assembling the front axle of a M322D MH Wheeled Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the carrier housing, planetary gears, bearings, seals, and brake discs. Reassembly instructions are also provided, with steps like installing bearings, seals, and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant and ensuring proper torque specifications are followed for nuts and bolts. Cleanliness and use of the correct tools are emphasized throughout.
This document provides disassembly instructions for the front and rear axles, carriers, hubs, and brakes of an M322C wheeled excavator. The front axle disassembly procedure involves 41 steps to remove components like the carrier housing, planetary gears, ring gear assembly, hub assembly, and spindle components. The rear axle disassembly involves 27 steps including removing the brake drum, gear assemblies, axle, hub assembly, dust shield, brake assembly, and spindle. Detailed illustrations are provided to identify each part and tooling required is listed.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then provides 29 steps to reassemble the swing drive, installing the components in reverse order and noting that all seals and gaskets must be replaced. Precise torques and clear illustrations are provided to ensure correct assembly.
This document provides instructions for disassembling and assembling the swing drive of an M318D MH wheeled excavator. The disassembly procedure involves using various tools to remove 28 individual parts from the swing drive assembly, including gears, bearings, seals, and housing components. The assembly procedure similarly uses tools to install the parts in reverse order and includes steps to properly set bearing preloads. Precautions are listed regarding cleaning parts and applying lubricant before assembly.
This document provides instructions for disassembling and assembling the swing drive of an M318C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant to components and ensuring proper torque specifications are achieved. Tools and safety precautions are also listed.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the rear axle of a M316C Wheeled Excavator. The disassembly procedure involves removing 23 components of the rear axle including the carrier housing, planetary gears, retaining rings, and hub. The assembly procedure describes installing these 23 components in reverse order and includes steps to measure clearances and install seals, bearings, and thrust washers correctly. Tools required are also listed.
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves using various tools to remove 28 individual parts from the swing drive housing. The assembly procedure similarly uses tools to install the parts in reverse order, noting that bearings and seals must be heated or cooled as needed and lubricated before installation. Precise torques are specified for tightening critical nuts to properly set bearing preloads.
The document provides instructions for disassembling and assembling the final drive carriers, hubs, and brakes of the rear axle of a M315D2 Wheeled Excavator. It lists the required tools and presents 23 steps for disassembly that include removing bolts, housings, gears, seals, and bearings. It then lists 27 steps for assembly that involve cleaning, inspecting, applying lubricants, and reinstalling components in reverse order while precisely measuring clearances and torque specifications. The purpose is to repair or replace parts while properly reassembling the rear axle.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M313D Wheeled Excavator. It lists 34 steps for disassembly, removing components like bolts, seals, springs, and bearings. For assembly, it lists 27 steps such as installing bearings, seals, rods, and calibrating components using tools and measurements to ensure proper lift-off limitation. Precise assembly is important to prevent contamination and ensure long component life.
The document provides instructions for disassembling and assembling the front axle of a M313D wheeled excavator. It lists required tools and gives step-by-step instructions to remove components such as the carrier housing, planetary gears, ring gear housing, brake discs, bearings and seals. Similarly, it outlines the assembly procedure and lists required tools, providing instructions to install components in reverse order and noting that anti-seize compound should be applied before assembling.
The document provides instructions for disassembling a piston pump used in a wheeled excavator. It lists 49 steps to fully disassemble the pump and its components. These include removing bolts, hoses, gears, plates, valves, springs, pistons, seals, and other internal parts. Detailed illustrations accompany each step to show how to access and remove the individual parts in the correct order. Safety notices are included to warn of potential hazards like stored energy in springs.
This document provides assembly instructions for a hydraulic pump in 3 steps:
1. It describes 60 assembly steps to install components like seals, springs, pistons, and covers inside the pump housing.
2. It explains how to install the pump control assembly, adding more components like valves, links, and seals.
3. Finally, it specifies installing the completed pump control onto the pump housing and connecting fittings to finish assembly.
This document provides instructions for disassembling and assembling the recoil spring on a 329D L excavator. It describes:
1. The required tools and sockets for disassembly and assembly.
2. The disassembly procedure which involves using a special recoil spring bench tool to safely compress the spring and remove components.
3. The assembly procedure which again uses the bench tool to compress the spring and measure its length during assembly. Proper spring length is critical.
This document provides installation instructions for a final drive on an excavator. It lists the required tools and parts. The procedure involves using lifting devices to position the final drive, applying anti-seize compound to bolts, and torquing the bolts to the specified values. The final drive is then removed from the lifting tools and the travel motor and track assembly are reconnected. Cleanliness and torque specifications are noted as important factors for the installation.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 18M3 MOTOR GRADER N9A
Configuration: 18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
16M Series 3 and 18M Series 3 Motor Graders Power Train
Media Number -UENR6763-02 Publication Date -01/09/2015 Date Updated -17/05/2017
i06891653
Service Brake (Wheel Spindle) - Assemble
SMCS - 4002-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C 140-7742 Sleeve 2
F
169-0503 Installation Kit 1
1U-8698(1)
Duo-Cone Seal Installer As 1
1U-6441(2)
Duo-Cone Seal Installer As 1
G 1U-8846 Gasket Sealant 1
H 9S-3263 Loctite 243 1
J
8T-4132 Nut 6
- M16 - 2.00 × 180mm Bolt 3
K 6V-7030 Micrometer Depth Gauge Gp 1
L 6V-2055 Grease 1
(1)
For a Duo-cone Seal with a diameter of 160.09 ± 0.58 mm (6.303 ± 0.023 inch)
(2)
For a Duo-cone Seal with a diameter of 191.26 ± 0.25 mm (7.529 ± 0.009 inch)
1/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01378162
1. Install spacer (22).
Illustration 2 g01349477
2. Raise the temperature of bearing cone (21). Install bearing cone (21). Ensure that bearing
cone (21) is seated correctly against the spacer.
2/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01349462
3. Use Tooling (F) to install the second half of Duo-Cone seal (19). Refer to Disassembly and
Assembly, "Duo-Cone Conventional Seals - Install".
Illustration 4 g01349436
4. Lower the temperature of bearing cup (20). Install bearing cup (20). Ensure that bearing cup
(20) is seated correctly. Use Tooling (F) to install the first half of Duo-Cone seal (19). Refer
to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Illustration 5 g01349430
3/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Use Tooling (A) and a suitable lifting device to install housing (18). Apply Tooling (L) onto
the bores of housing (18). The weight of housing (18) is approximately 75 kg (165 lb).
Illustration 6 g01349359
Illustration 7 g06277637
6. Install seals (17).
Note: Some machines require the seals to be installed on the piston, while others require the
seals to be installed in the housing.
Illustration 8 g01349354
4/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 7. Install hub (16), piston (14), and spacers (15).
Illustration 9 g01349348
8. Install discs (13) and plates (12). Install springs (11).
Note: Ensure that the vent holes that are in discs (13) are aligned.
Illustration 10 g01349344
9. Lower the temperature of bearing cup (10). Install bearing cup (10) into cover (9).
Illustration 11 g01349575
5/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Apply Tooling (G) onto the mating surface of the housing. Use Tooling (A), and a suitable
lifting device to install cover (9). The weight of cover (9) is approximately 41 kg (90 lb).
11. Use Tooling (J) to compress the springs.
Illustration 12 g01349585
12. Install bolts (6). Remove Tooling (J).
Illustration 13 g01349540
13. Install bearing cone (8). Install O-ring seal (7).
6/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g01349338
14. Use Tooling (C) and a suitable lifting device to install sprocket (5). The weight of sprocket
(5) is approximately 36 kg (80 lb).
Illustration 15 g06297757
Shown is the pattern to update retainer (3) if necessary. The diameter for circle (R) is 70 mm (2.77 inch).
Illustration 16 g06195003
7/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g06023870
Illustration 18 g01349321
15. Position retainer (3) with no shims (4) installed. Install bolts (2) finger tight against the
retainer (3). Tighten bolts (2) to a torque of 90 N·m (66 lb ft). Repeat until bolts (2) no
longer turn. Rotate the housing three full rotations once the bolt torque has equalized at a
torque of 90 N·m (66 lb ft). Bolts (2) will have to be tightened several times followed by
three full rotations to ensure correct torque.
16. Loosen bolts (2) and finger tighten against retainer (3).
17. With bolts (2) finger tight only, rotate the housing three full rotations.
18. Tighten the bolts to 30 N·m (22 lb ft). Repeat until bolts no longer turn. Rotate the housing
three full rotations once the bolt torque has equalized at a torque of 30 N·m (22 lb ft). Bolts
(2) will have to be tightened several times followed by three full rotations to ensure correct
torque.
19. Remove two of bolts (2) and measure Dimension (X) using tooling (K). Subtract 0.03 mm
(0.001 inch) from the average of Dimension (X). This result is the desired thickness of shim
pack (4).
20. Build shim pack (4) to the dimension calculated in Step 19. Use the most number of thick
shims possible for the given total thickness. Position the thin shims between the thick shims.
8/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 21. Install retainer (3). Apply Tooling (H) to bolts (2). Install bolts (2) and tighten to a torque of
270 ± 40 N·m (199 ± 30 lb ft).
Illustration 19 g01349310
22. Use Tooling (A), Tooling (C), and a suitable lifting device to remove service brake (1) from
Tooling (B). The weight of service brake (1) is approximately 272 kg (600 lb).
Illustration 20 g06195026
23. Install nut (24) onto compensator (26) snug nut (24) against compensator (26) shoulder.
Apply air pressure to the brake piston. Tighten compensator (26) by hand until the
compensator contacts the piston. Measure the distance between nut (24) and housing face
(27), record this distance as Dimension (z).
24. Subtract 6 mm (0.236 inch) from Dimension (Z) and round down to the nearest 0.5 mm
(0.02 inch)To achieve the required number of shims.
25. Remove compensator (26) and nut (24) from housing.
26. Release air pressure from the brake piston.
9/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g06195040
27. Install the required number of shims (23) to compensator (26), up against nut (24).
28. Install O-ring (25) onto compensator (26).
29. Install compensator (26) by hand until the compensator contacts the piston. Loosen
compensator (26) 1/2 of a turn.
30. Hold compensator (26) and tighten nut (24) to a torque of 50 ± 10 N·m (37 ± 7 lb ft).
End By:
a. Install the service brake and the wheel spindle. Refer to Disassembly and Assembly,
"Service Brake (Wheel Spindle) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 24 11:38:37 UTC+0800 2020
10/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engi...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 18M3 MOTOR GRADER N9A
Configuration: 18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
16M Series 3 and 18M Series 3 Motor Graders Power Train
Media Number -UENR6763-02 Publication Date -01/09/2015 Date Updated -17/05/2017
i06148734
Housing (Tandem) - Remove and Install
SMCS - 4064-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Bracket As 2
B
442-9885 Retainer 1
1U-5898 Guide As, Sprocket 1
C 421-5662 Lifting Eye Assembly 2
Start By:
a. Remove the rear wheels.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.
1. Drain the oil from the housing (tandem). Refer to Operation and Maintenance Manual,
"Tandem Drive Oil - Change".
1/6
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g03874320
2. Remove hose assembly (1).
Illustration 2 g03877264
Illustration 3 g03877287
3. Attach Tooling (A) and a suitable lifting device to fender assembly (2). The weight of
fender assembly (2) is approximately 188 kg (414 lb).
4. Remove bolts (3).
2/6
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 10 g03874280
10. Install Tooling (B). Install bolts (11).
Illustration 11 g03874284
11. Attach Tooling (B).
Illustration 12 g03874305
12. Attach Tooling (C) and a suitable lifting device to housing (tandem) (13). The weight of
housing (tandem) (13) is approximately 1533 kg (3380 lb).
5/6
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 13 g03874276
13. Remove bolts (14). Remove housing (tandem) (13).
14. Repeat Step 1 through 13 for the opposite side.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Install housing (tandem) (13) in the reverse order of removal.
2. Tighten bolts (14) to a torque of 530 ± 70 N·m (391 ± 52 lb ft)
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 24 11:39:32 UTC+0800 2020
6/6
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 18M3 MOTOR GRADER N9A
Configuration: 18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
16M Series 3 and 18M Series 3 Motor Graders Power Train
Media Number -UENR6763-02 Publication Date -01/09/2015 Date Updated -17/05/2017
i06146156
Rear Axle, Differential and Final Drive - Remove
SMCS - 3258-011; 3278-011; 3282-011-RE; 4050-011; 4068-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 4
B 6V-6146 Load Leveling Beam 1
C 1U-9744 Floor Jack 1
Start By:
a. Remove the rear wheels and tires.
b. Remove the tandem housing.
c. Remove the bottom guard.
d. Remove the drive shaft.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Connect the steering frame lock. Refer to Operation and Maintenance Manual, "Steering
Frame Lock".
2. Release the system pressure. Refer to Operation and Maintenance Manual, "System
Pressure - Release".
3. Drain the rear axle oil. Refer to Operation and Maintenance Manual, "Transmission and
Differential Oil - Change".
Illustration 1 g03869423
4. Remove tube assembly (1). Disconnect harness assembly (2). Remove tube assembly (3).
Disconnect hose assembly (4). Remove hose (5). Remove tube assembly (6).
2/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g03869426
5. Disconnect hose (7). Remove tube assembly (8). Disconnect hose assemblies (9). Remove
lock valve (10).
Illustration 3 g03869430
6. Disconnect hose assembly (11).
Illustration 4 g03869437
7. Remove panel (12). Repeat this step for the opposite side of the engine enclosure.
3/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 5 g03869483
Typical example.
Illustration 6 g03869443
8. Attach Tooling (A), Tooling (B), and two suitable lifting devices onto rear axle, differential,
and final drive (13). The weight of rear axle, differential, and final drive (13) is
approximately 1828 kg (4030 lb). Repeat this step for the opposite side of rear axle,
differential, and final drive (13).
9. Position Tooling (C) under rear axle, differential, and final drive (13) in order to support the
differential housing.
Illustration 7 g03869476
4/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 10. Remove bolts (14). Repeat this step for the opposite side of the machine.
Illustration 8 g03869480
11. Remove bolts (15). Repeat this step for the opposite side of the machine.
Illustration 9 g03869491
Typical example.
12. Remove rear axle, differential, and final drive (13).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 24 11:40:28 UTC+0800 2020
5/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 18M3 MOTOR GRADER N9A
Configuration: 18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
16M Series 3 and 18M Series 3 Motor Graders Power Train
Media Number -UENR6763-02 Publication Date -01/09/2015 Date Updated -17/05/2017
i06146157
Rear Axle, Differential and Final Drive - Disassemble
SMCS - 3258-015; 3278-015; 3282-015-RE; 4050-015; 4068-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 4
B 8T-0514 Adjusting Screw 2
C 138-7574 Link Bracket 2
D
8B-7551 Bearing Puller Gp 1
1P-5546 Crossarm 1
3H-0465 Push-Puller Plate 2
5F-7366 Forcing Screw 1
E 1U-6692 Socket Wrench As 1
F 154-6183 Forcing Bolt 3
G
8B-7551 Bearing Puller Gp 1
1P-5546 Crossarm 1
3H-0465 Push-Puller Plate 2
5F-7366 Forcing Screw 1
H 1U-6405 Three Jaw Puller 1
1/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Start By:
a. Remove the rear axle, differential, and final drive.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.
Illustration 1 g03871880
Typical Example
1. Use Tooling (A) and two suitable lifting devices in order to position rear axle, differential,
and final drive (1) onto suitable cribbing. The weight of rear axle, differential, and final
drive (1) is approximately 1819 kg (4010 lb).
Illustration 2 g03871885
2. Remove bearing cone (2).
2/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g03871886
3. Remove two bolts (3) and insert Tooling (B).
4. Loosen remaining bolts (3). Attach Tooling (A) and a suitable lifting device to final drive
housing (4) the weight of final drive housing (4) is approximately 254 kg (560 lb).
5. Remove final drive housing (4).
Illustration 4 g03871999
6. Remove bolts (5A). Remove retainer (5).
Illustration 5 g03872004
3/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. 7. Remove shims (6). Use Tooling (A) and a suitable lifting device in order to remove housing
(7). The weight of housing (7) is approximately 77 kg (170 lb).
Illustration 6 g03872026
8. Remove thrust washer (8). Remove wear sleeves (9).
Illustration 7 g03872028
9. Turn over housing (7). Remove lip seal (10).
Illustration 8 g03872032
10. Remove bearing cup (11). Remove thrust washer (12).
4/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 9 g03872111
11. Remove lip seal (13). Remove bearing cup (14).
Illustration 10 g03872121
12. Use a suitable lifting device to remove carrier assembly (15) and drive shaft (16). The
weight of the carrier assembly (15) and drive shaft (16) is approximately 125 kg (275 lb).
Illustration 11 g03872141
13. Use Tooling (D) in order to remove bearing cone (17).
5/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...