The document provides instructions to remove the rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It describes draining fluids, removing mounting bolts and plates, and lifting out the assembly using lifting brackets and eyes. Tools required include brackets, a retainer, lifting eyes, and a sprocket guide. The assembly should be cleaned of contaminants before installation.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...dujjsjekkkdmm
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fusjejedrfjskekem
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjskekdmem
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjsefkkertsemme
This document provides instructions for assembling and disassembling a service brake and wheel spindle on a Caterpillar 18M3 motor grader. It outlines 30 steps for assembly, which include installing seals, discs, springs, bearings and other components. Removal instructions are also given for draining oil from the grader's tandem housing and removing parts like fenders, walkways and bolts. Tools required are listed.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjsekdmme
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...ze6074xunong
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure outlines installing these components in reverse order and notes to keep parts clean and check seals for wear.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, plates and bearings. The assembly procedure lists 21 steps for installing these components in reverse order and includes safety notices for spring loaded parts. Installation involves attaching hoses, brackets and bolting the 52 kg pump into place on the grader.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure lists 21 steps for installing the components in reverse order. Safety notices are included to warn of potential injury from spring loaded parts.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...dujjsjekkkdmm
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fusjejedrfjskekem
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjskekdmem
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjsefkkertsemme
This document provides instructions for assembling and disassembling a service brake and wheel spindle on a Caterpillar 18M3 motor grader. It outlines 30 steps for assembly, which include installing seals, discs, springs, bearings and other components. Removal instructions are also given for draining oil from the grader's tandem housing and removing parts like fenders, walkways and bolts. Tools required are listed.
Caterpillar cat 18 m3 motor grader (prefix n9a) service repair manual (n9a000...fjjsekdmme
The document provides instructions to remove a rear axle, differential, and final drive assembly from a Caterpillar 18M3 motor grader. It lists required tools and describes a 23 step process involving draining fluids, removing bolts and plates, and lifting heavy components like housings, sprockets, and wheels using lifting brackets and eyes. Proper cleaning and inspection of parts is emphasized to prevent contamination and wear.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...ze6074xunong
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure outlines installing these components in reverse order and notes to keep parts clean and check seals for wear.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, plates and bearings. The assembly procedure lists 21 steps for installing these components in reverse order and includes safety notices for spring loaded parts. Installation involves attaching hoses, brackets and bolting the 52 kg pump into place on the grader.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure lists 21 steps for installing the components in reverse order. Safety notices are included to warn of potential injury from spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...jkdkkdsmmd
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting all hoses and brackets. Safety notices are provided regarding contained fluids and spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...idksmmdmdm
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting all hoses and brackets. Safety notices are provided regarding contained fluids and spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...hean57759707
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting the hoses, harnesses and brackets. Safety notices are provided regarding contained fluids and wearing protective equipment when working with pressurized components.
Caterpillar cat 160 m 3 awd motor grader (prefix n9k) service repair manual (...fksefkskemm
This service repair manual provides instructions for disassembling and assembling the piston pump on a Caterpillar 160M 3 AWD motor grader. It lists the required tools and presents 18 steps for disassembly that include removing valves, seals, springs, spools and plugs. The 20 steps for assembly include installing these same components in reverse order as well as ensuring parts are clean and seals are in good condition. Installation involves attaching lifting and connecting hoses, harnesses and brackets.
Caterpillar cat 160 m 3 awd motor grader (prefix n9k) service repair manual (...fjjsekkskeoelkm
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 160M 3 AWD motor grader. It lists the required tools and gives step-by-step instructions for removing and installing various components of the piston pump like valves, springs, seals, pistons, plates and covers. Safety precautions are provided to prevent injury from parts under spring tension. The instructions are intended to guide maintenance and repair of the motor grader's hydraulic and steering systems.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...f8usejkdmmd8i
The document provides assembly and disassembly instructions for a piston motor and gear motor used in the hydraulic fan system of a Caterpillar 160M 3 motor grader. It includes 38 steps to assemble the piston motor, installing various seals, springs, bearings and other components. It also includes 7 steps to disassemble the gear motor, removing seals, gears, bearings and other parts. The instructions are accompanied by illustrations and require various specialty tools to correctly assemble and disassemble the hydraulic fan motors.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...tengtui535
The document provides assembly and disassembly instructions for a piston motor (hydraulic fan) and gear motor (hydraulic fan) used in a Caterpillar 160M 3 motor grader. It details 38 steps for piston motor assembly requiring various tools. It also details 7 steps for gear motor disassembly and 7 steps for assembly, requiring retaining ring pliers. The instructions include illustrations and specify tightening bolts to 140 N·m.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...f8seodkdmdmed3
The document provides assembly and disassembly instructions for a piston motor (hydraulic fan) and gear motor (hydraulic fan) used in a Caterpillar 160M 3 motor grader. It details 38 steps for piston motor assembly requiring various tools. It also details 7 steps for gear motor disassembly and 7 steps for assembly, requiring retaining ring pliers. The instructions are part of a service repair manual for motor grader systems.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...ze6074xunong
The document provides assembly and disassembly instructions for a piston motor and gear motor used in the hydraulic fan system of a Caterpillar 160M 3 motor grader. It includes 38 steps to assemble the piston motor, installing various seals, springs, bearings and other components. It also includes 7 steps to disassemble the gear motor, removing seals, gears, bearings and other parts. The instructions are accompanied by illustrations and require various specialty tools to correctly assemble and disassemble the hydraulic fan motors.
This document provides instructions for assembling the final drive of an excavator model 329D L. It lists the required tools and parts. The procedure involves installing bearings in the main housing and motor housing using a press to apply the proper preload. Shims are used to take up any clearance between the housings. Duo-Cone seals are installed in the housings using a special tool. Cleanliness is emphasized throughout the assembly process.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals, and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 428 SERIES II BACKHOE LOADER (Prefix 6TC) Service Repair Manu...jkdkkdsmmd
The document provides instructions for disassembling and assembling the rear axle group and differential of a 428 Series II Backhoe Loader. It describes removing and installing the rear axle group which involves disconnecting linkages, brackets, and mounting hardware. Steps are provided to disassemble the rear axle group into individual components like housing, gears, and brakes. The differential is also disassembled by removing case halves, bearings, gears, and other parts. Precise assembly steps list installing components in reverse order and include details like torque specifications.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before separating assembly components.
3. Reassembling the spring assembly in the tooling bench and using hydraulic force to compress the spring into position, requiring several tons of force. Proper centering and leveling of the assembly is critical.
This document provides the installation procedure for a final drive on an excavator. It lists the required tools and parts. The procedure involves using lifting devices to position the final drive, applying anti-seize compound to bolts, and torquing the bolts to the specified values. It also describes attaching lifting brackets and removing the lifting equipment once installation is complete.
The document is a service repair manual that provides step-by-step instructions for disassembling the final drive components of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, carrier assembly, planetary gears, and separating the sprocket housing from the motor housing. Detailed illustrations accompany each step to show how to remove individual parts like seals, shafts, and bearings from within the final drive assembly. Special tools are listed that may be required for tasks like removing retaining rings.
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into a motor housing in the correct order.
3. Attaching lifting devices and link brackets to install the assembled swing motor and remove the swing drive, which each weigh over 500 lbs.
This document provides instructions for removing and installing a swing motor on an excavator model 329D2 L. The removal procedure involves draining oil from the swing drive, using tools to remove bolts securing the swing drive, and using lifting equipment to remove the swing motor due to its weight of approximately 77 kg. The installation procedure outlines connecting harness assemblies, hoses, and tightening connections to specified torques.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling a final drive transmission. It begins by removing the final drive from the excavator and securing it to a repair stand. Various components are then removed in sequential order, including the cover, gears, carrier assembly, planetary gears, and seals. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanism. Over 30 individual steps are outlined with descriptions and illustrations.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D L Excavator (Prefix BFC) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling and assembling the transmission of a 329D L and 329D LN excavator. It lists 37 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 36 steps for assembly, reinstalling these components in reverse order and noting cleaning requirements. Precise measurements are taken to determine the correct shim thickness for preloading bearings during assembly.
More Related Content
Similar to Caterpillar Cat 18M3 MOTOR GRADER (Prefix N9A) Service Repair Manual Instant Download.pdf
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...jkdkkdsmmd
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting all hoses and brackets. Safety notices are provided regarding contained fluids and spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...idksmmdmdm
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting all hoses and brackets. Safety notices are provided regarding contained fluids and spring loaded parts.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...hean57759707
The document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal procedure involves removing the rear chassis support, then disconnecting hoses, harnesses and brackets connecting the pump. The installation procedure specifies cleaning parts and checking seals before lifting the 52 kg pump into place using a lifting device and reconnecting the hoses, harnesses and brackets. Safety notices are provided regarding contained fluids and wearing protective equipment when working with pressurized components.
Caterpillar cat 160 m 3 awd motor grader (prefix n9k) service repair manual (...fksefkskemm
This service repair manual provides instructions for disassembling and assembling the piston pump on a Caterpillar 160M 3 AWD motor grader. It lists the required tools and presents 18 steps for disassembly that include removing valves, seals, springs, spools and plugs. The 20 steps for assembly include installing these same components in reverse order as well as ensuring parts are clean and seals are in good condition. Installation involves attaching lifting and connecting hoses, harnesses and brackets.
Caterpillar cat 160 m 3 awd motor grader (prefix n9k) service repair manual (...fjjsekkskeoelkm
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 160M 3 AWD motor grader. It lists the required tools and gives step-by-step instructions for removing and installing various components of the piston pump like valves, springs, seals, pistons, plates and covers. Safety precautions are provided to prevent injury from parts under spring tension. The instructions are intended to guide maintenance and repair of the motor grader's hydraulic and steering systems.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...f8usejkdmmd8i
The document provides assembly and disassembly instructions for a piston motor and gear motor used in the hydraulic fan system of a Caterpillar 160M 3 motor grader. It includes 38 steps to assemble the piston motor, installing various seals, springs, bearings and other components. It also includes 7 steps to disassemble the gear motor, removing seals, gears, bearings and other parts. The instructions are accompanied by illustrations and require various specialty tools to correctly assemble and disassemble the hydraulic fan motors.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...tengtui535
The document provides assembly and disassembly instructions for a piston motor (hydraulic fan) and gear motor (hydraulic fan) used in a Caterpillar 160M 3 motor grader. It details 38 steps for piston motor assembly requiring various tools. It also details 7 steps for gear motor disassembly and 7 steps for assembly, requiring retaining ring pliers. The instructions include illustrations and specify tightening bolts to 140 N·m.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...f8seodkdmdmed3
The document provides assembly and disassembly instructions for a piston motor (hydraulic fan) and gear motor (hydraulic fan) used in a Caterpillar 160M 3 motor grader. It details 38 steps for piston motor assembly requiring various tools. It also details 7 steps for gear motor disassembly and 7 steps for assembly, requiring retaining ring pliers. The instructions are part of a service repair manual for motor grader systems.
Caterpillar Cat 160M 3 MOTOR GRADER (Prefix N9L) Service Repair Manual Instan...ze6074xunong
The document provides assembly and disassembly instructions for a piston motor and gear motor used in the hydraulic fan system of a Caterpillar 160M 3 motor grader. It includes 38 steps to assemble the piston motor, installing various seals, springs, bearings and other components. It also includes 7 steps to disassemble the gear motor, removing seals, gears, bearings and other parts. The instructions are accompanied by illustrations and require various specialty tools to correctly assemble and disassemble the hydraulic fan motors.
Similar to Caterpillar Cat 18M3 MOTOR GRADER (Prefix N9A) Service Repair Manual Instant Download.pdf (9)
This document provides instructions for assembling the final drive of an excavator model 329D L. It lists the required tools and parts. The procedure involves installing bearings in the main housing and motor housing using a press to apply the proper preload. Shims are used to take up any clearance between the housings. Duo-Cone seals are installed in the housings using a special tool. Cleanliness is emphasized throughout the assembly process.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals, and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 428 SERIES II BACKHOE LOADER (Prefix 6TC) Service Repair Manu...jkdkkdsmmd
The document provides instructions for disassembling and assembling the rear axle group and differential of a 428 Series II Backhoe Loader. It describes removing and installing the rear axle group which involves disconnecting linkages, brackets, and mounting hardware. Steps are provided to disassemble the rear axle group into individual components like housing, gears, and brakes. The differential is also disassembled by removing case halves, bearings, gears, and other parts. Precise assembly steps list installing components in reverse order and include details like torque specifications.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before separating assembly components.
3. Reassembling the spring assembly in the tooling bench and using hydraulic force to compress the spring into position, requiring several tons of force. Proper centering and leveling of the assembly is critical.
This document provides the installation procedure for a final drive on an excavator. It lists the required tools and parts. The procedure involves using lifting devices to position the final drive, applying anti-seize compound to bolts, and torquing the bolts to the specified values. It also describes attaching lifting brackets and removing the lifting equipment once installation is complete.
The document is a service repair manual that provides step-by-step instructions for disassembling the final drive components of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, carrier assembly, planetary gears, and separating the sprocket housing from the motor housing. Detailed illustrations accompany each step to show how to remove individual parts like seals, shafts, and bearings from within the final drive assembly. Special tools are listed that may be required for tasks like removing retaining rings.
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into a motor housing in the correct order.
3. Attaching lifting devices and link brackets to install the assembled swing motor and remove the swing drive, which each weigh over 500 lbs.
This document provides instructions for removing and installing a swing motor on an excavator model 329D2 L. The removal procedure involves draining oil from the swing drive, using tools to remove bolts securing the swing drive, and using lifting equipment to remove the swing motor due to its weight of approximately 77 kg. The installation procedure outlines connecting harness assemblies, hoses, and tightening connections to specified torques.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling a final drive transmission. It begins by removing the final drive from the excavator and securing it to a repair stand. Various components are then removed in sequential order, including the cover, gears, carrier assembly, planetary gears, and seals. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanism. Over 30 individual steps are outlined with descriptions and illustrations.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D L Excavator (Prefix BFC) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling and assembling the transmission of a 329D L and 329D LN excavator. It lists 37 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 36 steps for assembly, reinstalling these components in reverse order and noting cleaning requirements. Precise measurements are taken to determine the correct shim thickness for preloading bearings during assembly.
This document provides instructions for disassembling and assembling the travel motor of a 320D2L excavator. The disassembly process involves removing 27 components from the travel motor body and head. The assembly process reverses the disassembly steps and cautions that all components must be reinstalled in their original positions and orientations. Proper cleaning of components before and after disassembly and assembly is emphasized to prevent contamination of the hydraulic system.
This document provides instructions for servicing the air conditioning system on Caterpillar 322 and 322L excavators. It describes safety precautions when working with refrigerant and outlines procedures for preparing the machine, removing and installing components like lines, the compressor, and performing functions like evacuating and charging the system. Personal protective equipment is required as the system is pressurized and contains refrigerant that can cause injury.
This document provides instructions for removing and installing a governor and fuel injection control linkage on an excavator. It begins with an overview of the required tools. The removal procedure involves disconnecting tubes and cables, removing clips and pins, and taking off bolts. The installation procedure specifies cleaning and lubricating parts, replacing seals, and using tools to install clips, pins and bolts in the reverse order of removal. Precautions are given to keep parts clean and check adjustments after installation.
Caterpillar Cat 320D2 L Excavator (Prefix YEA) Service Repair Manual Instant ...jkdkkdsmmd
This document provides assembly instructions for excavator models 320D2 and 320D2 L. It outlines 49 assembly steps requiring various tools. The steps include installing components like the pump housing, swashplate assemblies, shaft assemblies, barrel assemblies, port plates, head assembly, seal assembly, control linkage, and pump control components. Precautions are provided for steps involving released spring forces.
Caterpillar Cat 320D2 L Excavator (Prefix RAR) Service Repair Manual Instant ...jkdkkdsmmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C7.1 engine. It describes the required tools and outlines a multi-step process that involves positioning the piston at top dead center, compressing the valve spring with a tool to remove keepers and the spring, and reversing the process to install new springs. Safety notices are provided to wear protective equipment when working with compressed springs.
This document provides assembly instructions for excavator models 320D2 and 320D2 L. It outlines 49 assembly steps requiring various tools. The steps include installing components like the pump housing, swashplate assemblies, shaft assemblies, barrel assemblies, port plates, head assembly, seal assembly, control linkage, and pump control components. Precautions are provided for steps involving released spring forces.
The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 320D2 excavator engine. The flywheel removal procedure involves removing bolts and installing guide studs to lift the flywheel off. The crankshaft rear seal is part of a sealed assembly that must be replaced if removed. Installation involves aligning and pressing the new seal onto the crankshaft flange.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 18M3 MOTOR GRADER N9A
Configuration: 18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
16M Series 3 and 18M Series 3 Motor Graders Power Train
Media Number -UENR6763-02 Publication Date -01/09/2015 Date Updated -17/05/2017
i06891653
Service Brake (Wheel Spindle) - Assemble
SMCS - 4002-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C 140-7742 Sleeve 2
F
169-0503 Installation Kit 1
1U-8698(1)
Duo-Cone Seal Installer As 1
1U-6441(2)
Duo-Cone Seal Installer As 1
G 1U-8846 Gasket Sealant 1
H 9S-3263 Loctite 243 1
J
8T-4132 Nut 6
- M16 - 2.00 × 180mm Bolt 3
K 6V-7030 Micrometer Depth Gauge Gp 1
L 6V-2055 Grease 1
(1)
For a Duo-cone Seal with a diameter of 160.09 ± 0.58 mm (6.303 ± 0.023 inch)
(2)
For a Duo-cone Seal with a diameter of 191.26 ± 0.25 mm (7.529 ± 0.009 inch)
1/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01378162
1. Install spacer (22).
Illustration 2 g01349477
2. Raise the temperature of bearing cone (21). Install bearing cone (21). Ensure that bearing
cone (21) is seated correctly against the spacer.
2/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01349462
3. Use Tooling (F) to install the second half of Duo-Cone seal (19). Refer to Disassembly and
Assembly, "Duo-Cone Conventional Seals - Install".
Illustration 4 g01349436
4. Lower the temperature of bearing cup (20). Install bearing cup (20). Ensure that bearing cup
(20) is seated correctly. Use Tooling (F) to install the first half of Duo-Cone seal (19). Refer
to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Illustration 5 g01349430
3/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Use Tooling (A) and a suitable lifting device to install housing (18). Apply Tooling (L) onto
the bores of housing (18). The weight of housing (18) is approximately 75 kg (165 lb).
Illustration 6 g01349359
Illustration 7 g06277637
6. Install seals (17).
Note: Some machines require the seals to be installed on the piston, while others require the
seals to be installed in the housing.
Illustration 8 g01349354
4/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 7. Install hub (16), piston (14), and spacers (15).
Illustration 9 g01349348
8. Install discs (13) and plates (12). Install springs (11).
Note: Ensure that the vent holes that are in discs (13) are aligned.
Illustration 10 g01349344
9. Lower the temperature of bearing cup (10). Install bearing cup (10) into cover (9).
Illustration 11 g01349575
5/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Apply Tooling (G) onto the mating surface of the housing. Use Tooling (A), and a suitable
lifting device to install cover (9). The weight of cover (9) is approximately 41 kg (90 lb).
11. Use Tooling (J) to compress the springs.
Illustration 12 g01349585
12. Install bolts (6). Remove Tooling (J).
Illustration 13 g01349540
13. Install bearing cone (8). Install O-ring seal (7).
6/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g01349338
14. Use Tooling (C) and a suitable lifting device to install sprocket (5). The weight of sprocket
(5) is approximately 36 kg (80 lb).
Illustration 15 g06297757
Shown is the pattern to update retainer (3) if necessary. The diameter for circle (R) is 70 mm (2.77 inch).
Illustration 16 g06195003
7/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g06023870
Illustration 18 g01349321
15. Position retainer (3) with no shims (4) installed. Install bolts (2) finger tight against the
retainer (3). Tighten bolts (2) to a torque of 90 N·m (66 lb ft). Repeat until bolts (2) no
longer turn. Rotate the housing three full rotations once the bolt torque has equalized at a
torque of 90 N·m (66 lb ft). Bolts (2) will have to be tightened several times followed by
three full rotations to ensure correct torque.
16. Loosen bolts (2) and finger tighten against retainer (3).
17. With bolts (2) finger tight only, rotate the housing three full rotations.
18. Tighten the bolts to 30 N·m (22 lb ft). Repeat until bolts no longer turn. Rotate the housing
three full rotations once the bolt torque has equalized at a torque of 30 N·m (22 lb ft). Bolts
(2) will have to be tightened several times followed by three full rotations to ensure correct
torque.
19. Remove two of bolts (2) and measure Dimension (X) using tooling (K). Subtract 0.03 mm
(0.001 inch) from the average of Dimension (X). This result is the desired thickness of shim
pack (4).
20. Build shim pack (4) to the dimension calculated in Step 19. Use the most number of thick
shims possible for the given total thickness. Position the thin shims between the thick shims.
8/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 21. Install retainer (3). Apply Tooling (H) to bolts (2). Install bolts (2) and tighten to a torque of
270 ± 40 N·m (199 ± 30 lb ft).
Illustration 19 g01349310
22. Use Tooling (A), Tooling (C), and a suitable lifting device to remove service brake (1) from
Tooling (B). The weight of service brake (1) is approximately 272 kg (600 lb).
Illustration 20 g06195026
23. Install nut (24) onto compensator (26) snug nut (24) against compensator (26) shoulder.
Apply air pressure to the brake piston. Tighten compensator (26) by hand until the
compensator contacts the piston. Measure the distance between nut (24) and housing face
(27), record this distance as Dimension (z).
24. Subtract 6 mm (0.236 inch) from Dimension (Z) and round down to the nearest 0.5 mm
(0.02 inch)To achieve the required number of shims.
25. Remove compensator (26) and nut (24) from housing.
26. Release air pressure from the brake piston.
9/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g06195040
27. Install the required number of shims (23) to compensator (26), up against nut (24).
28. Install O-ring (25) onto compensator (26).
29. Install compensator (26) by hand until the compensator contacts the piston. Loosen
compensator (26) 1/2 of a turn.
30. Hold compensator (26) and tighten nut (24) to a torque of 50 ± 10 N·m (37 ± 7 lb ft).
End By:
a. Install the service brake and the wheel spindle. Refer to Disassembly and Assembly,
"Service Brake (Wheel Spindle) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 24 11:38:37 UTC+0800 2020
10/10
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engi...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 18M3 MOTOR GRADER N9A
Configuration: 18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
16M Series 3 and 18M Series 3 Motor Graders Power Train
Media Number -UENR6763-02 Publication Date -01/09/2015 Date Updated -17/05/2017
i06148734
Housing (Tandem) - Remove and Install
SMCS - 4064-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Bracket As 2
B
442-9885 Retainer 1
1U-5898 Guide As, Sprocket 1
C 421-5662 Lifting Eye Assembly 2
Start By:
a. Remove the rear wheels.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.
1. Drain the oil from the housing (tandem). Refer to Operation and Maintenance Manual,
"Tandem Drive Oil - Change".
1/6
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g03874320
2. Remove hose assembly (1).
Illustration 2 g03877264
Illustration 3 g03877287
3. Attach Tooling (A) and a suitable lifting device to fender assembly (2). The weight of
fender assembly (2) is approximately 188 kg (414 lb).
4. Remove bolts (3).
2/6
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 10 g03874280
10. Install Tooling (B). Install bolts (11).
Illustration 11 g03874284
11. Attach Tooling (B).
Illustration 12 g03874305
12. Attach Tooling (C) and a suitable lifting device to housing (tandem) (13). The weight of
housing (tandem) (13) is approximately 1533 kg (3380 lb).
5/6
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 13 g03874276
13. Remove bolts (14). Remove housing (tandem) (13).
14. Repeat Step 1 through 13 for the opposite side.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Install housing (tandem) (13) in the reverse order of removal.
2. Tighten bolts (14) to a torque of 530 ± 70 N·m (391 ± 52 lb ft)
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 24 11:39:32 UTC+0800 2020
6/6
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 18M3 MOTOR GRADER N9A
Configuration: 18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
16M Series 3 and 18M Series 3 Motor Graders Power Train
Media Number -UENR6763-02 Publication Date -01/09/2015 Date Updated -17/05/2017
i06146156
Rear Axle, Differential and Final Drive - Remove
SMCS - 3258-011; 3278-011; 3282-011-RE; 4050-011; 4068-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 4
B 6V-6146 Load Leveling Beam 1
C 1U-9744 Floor Jack 1
Start By:
a. Remove the rear wheels and tires.
b. Remove the tandem housing.
c. Remove the bottom guard.
d. Remove the drive shaft.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Connect the steering frame lock. Refer to Operation and Maintenance Manual, "Steering
Frame Lock".
2. Release the system pressure. Refer to Operation and Maintenance Manual, "System
Pressure - Release".
3. Drain the rear axle oil. Refer to Operation and Maintenance Manual, "Transmission and
Differential Oil - Change".
Illustration 1 g03869423
4. Remove tube assembly (1). Disconnect harness assembly (2). Remove tube assembly (3).
Disconnect hose assembly (4). Remove hose (5). Remove tube assembly (6).
2/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g03869426
5. Disconnect hose (7). Remove tube assembly (8). Disconnect hose assemblies (9). Remove
lock valve (10).
Illustration 3 g03869430
6. Disconnect hose assembly (11).
Illustration 4 g03869437
7. Remove panel (12). Repeat this step for the opposite side of the engine enclosure.
3/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 5 g03869483
Typical example.
Illustration 6 g03869443
8. Attach Tooling (A), Tooling (B), and two suitable lifting devices onto rear axle, differential,
and final drive (13). The weight of rear axle, differential, and final drive (13) is
approximately 1828 kg (4030 lb). Repeat this step for the opposite side of rear axle,
differential, and final drive (13).
9. Position Tooling (C) under rear axle, differential, and final drive (13) in order to support the
differential housing.
Illustration 7 g03869476
4/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 10. Remove bolts (14). Repeat this step for the opposite side of the machine.
Illustration 8 g03869480
11. Remove bolts (15). Repeat this step for the opposite side of the machine.
Illustration 9 g03869491
Typical example.
12. Remove rear axle, differential, and final drive (13).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 24 11:40:28 UTC+0800 2020
5/5
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 18M3 MOTOR GRADER N9A
Configuration: 18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
16M Series 3 and 18M Series 3 Motor Graders Power Train
Media Number -UENR6763-02 Publication Date -01/09/2015 Date Updated -17/05/2017
i06146157
Rear Axle, Differential and Final Drive - Disassemble
SMCS - 3258-015; 3278-015; 3282-015-RE; 4050-015; 4068-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 4
B 8T-0514 Adjusting Screw 2
C 138-7574 Link Bracket 2
D
8B-7551 Bearing Puller Gp 1
1P-5546 Crossarm 1
3H-0465 Push-Puller Plate 2
5F-7366 Forcing Screw 1
E 1U-6692 Socket Wrench As 1
F 154-6183 Forcing Bolt 3
G
8B-7551 Bearing Puller Gp 1
1P-5546 Crossarm 1
3H-0465 Push-Puller Plate 2
5F-7366 Forcing Screw 1
H 1U-6405 Three Jaw Puller 1
1/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Start By:
a. Remove the rear axle, differential, and final drive.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.
Illustration 1 g03871880
Typical Example
1. Use Tooling (A) and two suitable lifting devices in order to position rear axle, differential,
and final drive (1) onto suitable cribbing. The weight of rear axle, differential, and final
drive (1) is approximately 1819 kg (4010 lb).
Illustration 2 g03871885
2. Remove bearing cone (2).
2/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g03871886
3. Remove two bolts (3) and insert Tooling (B).
4. Loosen remaining bolts (3). Attach Tooling (A) and a suitable lifting device to final drive
housing (4) the weight of final drive housing (4) is approximately 254 kg (560 lb).
5. Remove final drive housing (4).
Illustration 4 g03871999
6. Remove bolts (5A). Remove retainer (5).
Illustration 5 g03872004
3/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 7. Remove shims (6). Use Tooling (A) and a suitable lifting device in order to remove housing
(7). The weight of housing (7) is approximately 77 kg (170 lb).
Illustration 6 g03872026
8. Remove thrust washer (8). Remove wear sleeves (9).
Illustration 7 g03872028
9. Turn over housing (7). Remove lip seal (10).
Illustration 8 g03872032
10. Remove bearing cup (11). Remove thrust washer (12).
4/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. Illustration 9 g03872111
11. Remove lip seal (13). Remove bearing cup (14).
Illustration 10 g03872121
12. Use a suitable lifting device to remove carrier assembly (15) and drive shaft (16). The
weight of the carrier assembly (15) and drive shaft (16) is approximately 125 kg (275 lb).
Illustration 11 g03872141
13. Use Tooling (D) in order to remove bearing cone (17).
5/17
18M Series 3 Motor Grader N9A00001-UP (MACHINE) POWERED BY C13 Engine...
2020/4/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...