This document provides instructions for removing the drawbar from a 140M Motor Grader. It lists the required tools, gives safety warnings about hydraulic pressure, and outlines a 26-step procedure involving lowering the blade, removing bolts and pins, and using lifting equipment to remove the drawbar. Proper identification and plugging of hoses is noted to prevent fluid loss and contamination during the process.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140M MOTOR GRADER B9M
Configuration: 140M Motor Grader B9M00001-UP (MACHINE)
Disassembly and Assembly
140M Motor Grader
Media Number -KENR6424-07 Publication Date -01/04/2015 Date Updated -06/04/2015
i05508509
Circle - Install
SMCS - 6154-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B
1P-1831 Adapter 1
4C-9633 Puller Stud 1
9U-6833 Nut 1
5P-8250 Washer 1
5P-4197 Spacer 1
6V-3160 Double Acting Cylinder 1
350-7768 Electric Hydraulic Pump Gp (115V) 1
350-7769 Electric Hydraulic Pump Gp (230V) 1
C
4C-6486 Stand 1
8S-7621 Tube 1
8S-7615 Pin 1
8S-8048 Saddle 1
1/9
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, PERJ1017, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Hydraulic oil pressure can remain in the hydraulic system on this
machine after the engine and pump have been stopped. Serious injury
can result if this pressure is not released before any service is done on
the hydraulic systems. In order to prevent possible injury, release the
hydraulic system pressure before working on any fitting, hose, or
hydraulic component.
Lower all attachments to the ground before service is started. If the
hydraulic system must be serviced, tested, or adjusted with the
attachment in the raised position, the attachments and lift cylinders
must be supported properly.
Always move the machine to a location away from the travel of other
machines. Be sure that other personnel are not near the machine when
the engine is running and tests or adjustments are being made.
When you are using hydraulic cylinders and puller studs, always ensure
that the rated capacity of the puller stud meets or exceeds the rated
capacity of the hydraulic cylinder. If the puller stud does not meet or
exceed the rated capacity of the hydraulic cylinder, a sudden failure of
the puller stud could occur. The sudden failure of the puller stud could
result in personal injury or death.
2/9
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g01402122
1. Lower the temperature of two bearings (24). Use Tooling (B) in order to install two bearings
(24) (not shown) into blade (1). Repeat this step for the opposite side.
Illustration 2 g01402120
2. Lower the temperature of two bearings (23). Use Tooling (B) in order to install two bearings
(23) (not shown) in circle assembly (10). Repeat this step for the opposite side.
Illustration 3 g01402117
3. Start the machine. Lower drawbar (22) onto circle assembly (10).
3/9
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 4. Move the machine in order to engage the circle drive pinion on circle assembly (10).
Illustration 4 g01402108
5. Stop the engine. Install wear strip (21) and shoe (20).
Note: Note the location of shoe (20). Repeat this step for the remaining shoes.
6. Install bolts (19).
7. Tighten setscrew (18).
8. Tighten nuts (17).
Illustration 5 g01402102
9. Install wear strips (16).
4/9
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 12. Position bracket (13).
13. Install washer (12) and bolt (11).
Illustration 9 g01402057
14. Start the engine. Operate the machine in order to raise circle assembly (10) off the suitable
cribbing and Tooling (C). Remove Tooling (C) from circle assembly (10). Reposition the
machine or the blade.
Illustration 10 g01402047
15. Position shims (5).
Note: Use the required number of shims (5) in order to provide a sliding fit with a
maximum of 1.800 mm (0.0709 inch) clearance between the bracket and the beam.
16. Install shaft assembly (9).
17. Install washer (6), nut (7), and cotter pin (8).
Note: Tighten nut (7) to 0.000 mm (0.0000 inch) clearance and back off one slot.
6/9
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 11 g01402035
18. Attach Tooling (A) and a suitable lifting device to blade (1). The weight of blade (1) is
approximately 907 kg (2000 lb). Use Tooling (A) and the suitable lifting device in order to
raise blade (1).
Illustration 12 g01402018
19. Connect hose assemblies (3). Install bolts (4).
7/9
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 13 g01401879
20. Install blade tip cylinder (2). Refer to Disassembly and Assembly, "Blade Tip Cylinder -
Remove and Install".
Illustration 14 g01401875
21. Remove Tooling (A) from blade (1).
Illustration 15 g01402224
8/9
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 16 g01402378
22. Loosen bolts (19) in order to allow movement in shoes (20). Seat circle drive pinion (25) in
the teeth on circle (10). Move circle (10) in order to obtain Dimension (C). Dimension (C)
must be 50.00 + 2.50 − 0.50 mm (2.000 + 0.098 − 0.020 inch).
23. Loosen nuts (17). Evenly adjust setscrews (18) against shoes (20) in order to bring shoes
(20) in contact with circle (10). Back off setscrews (18) in order to obtain Dimension (B).
Dimension (B) must be no greater than 0.80 mm (0.032 inch).
24. Tighten bolts (19) to a torque of 530 ± 70 N·m (391 ± 52 lb ft). Tighten nuts (17) to a torque
of 200 ± 30 N·m (148 ± 22 lb ft).
25. Measure Dimension (A) between wear strip (16) and circle (10). Dimension (A) must be no
greater than 0.50 mm (0.020 inch). Add or remove shims (15) in order to obtain the correct
dimension.
26. Start the engine and run the engine. Rotate the circle through the entire working range and
check for binding. The circle must rotate freely.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 14 18:42:23 UTC+0800 2020
9/9
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140M MOTOR GRADER B9M
Configuration: 140M Motor Grader B9M00001-UP (MACHINE)
Disassembly and Assembly
140M Motor Grader
Media Number -KENR6424-07 Publication Date -01/04/2015 Date Updated -06/04/2015
i07332155
Drawbar - Remove
SMCS - 6153-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
504-9791 Lift Gp (60Hz)(1)
1
OR
504-9793 Lift Gp (50Hz)(2)
1
B 439-3940 Bracket As 1
(1)
High-Voltage (480V) Low-Voltage (240V)
(2)
High-Voltage (400V) Low-Voltage (200V)
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
1/6
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned to prevent dirt from entering the internal mechanism.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Note: Put identification marks on all hoses and on all hose assemblies for installation purposes.
Plug all hose assemblies to prevent fluid loss, and to prevent contaminants from entering the
system.
1. Connect the steering frame lock. Refer to Operation and Maintenance Manual, "Steering
Frame Lock".
2/6
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g06287257
2. Position drawbar (1) to the left side of the machine. Position the blade onto suitable
cribbing. Support the circle with Tooling (A) as shown. Refer to Tool Operating Manual,
NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A).
3. Stop the engine. Release the system pressure. Refer to Disassembly and Assembly, "System
Pressure - Release".
Illustration 2 g01403317
4. Attach Tooling (B) and a suitable lifting device to swivel (3). The weight of swivel (3) is
approximately 41 kg (90 lb).
5. Disconnect hose assemblies (2), (5), and (6).
6. Remove bolts (7) and lower swivel (3).
7. Remove the suitable lifting device.
8. Remove all clamps (4) that connect hose assemblies (6) to the drawbar.
3/6
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g01403392
9. Remove centershift cylinder (8). Refer to Disassembly and Assembly, "Centershift Cylinder
- Remove and Install".
10. Remove bolts (10), cap (9), and the shims. Repeat this step for the opposite side of the
machine.
Note: Note the number and the location of the shims.
11. Use the hydraulics to retract the blade lift cylinders.
Note: Secure the blade lift cylinders to the front frame.
Illustration 4 g01403404
12. Loosen nuts (11).
13. Loosen set screws (12).
14. Remove bolts (13).
4/6
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
16. 15. Remove shoe (14) and wear strip (15).
Note: Note the location of the shoes.
16. Repeat Steps 12 through 15 for the remaining shoes.
Illustration 5 g01403432
17. Attach a suitable lifting device to drawbar (1).
18. Remove bolts (16).
19. Remove drawbar (1). The weight of drawbar (1) is approximately 907 kg (2000 lb).
Illustration 6 g03485398
20. Remove bolts (22).
21. Remove adapter (17) and shims (18) from drawbar (1).
22. Remove bolts (19) and ball (20). Remove adapter (21) from drawbar (1).
5/6
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 23. If necessary, remove the circle drive. Refer to Disassembly and Assembly, "Circle Drive -
Remove".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 14 18:43:19 UTC+0800 2020
6/6
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140M MOTOR GRADER B9M
Configuration: 140M Motor Grader B9M00001-UP (MACHINE)
Disassembly and Assembly
140M Motor Grader
Media Number -KENR6424-07 Publication Date -01/04/2015 Date Updated -06/04/2015
i07339896
Drawbar - Install
SMCS - 6153-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
504-9791 Lift Gp (60 Hz)(1)
1
OR
504-9793 Lift Gp (50 Hz)(2)
1
B 439-3940 Bracket As 1
(1)
High-Voltage (480V) Low-Voltage (240V)
(2)
High-Voltage (400V) Low-Voltage (200V)
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. If necessary, install the circle drive. Refer to Disassembly and Assembly, "Circle Drive -
Install".
1/6
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g03485398
2. Install adapter (21) to drawbar (1). Install ball (20) and bolts (19) to drawbar (1). Tighten
bolts (19) to a torque of 500 ± 65 N·m (369 ± 48 lb ft).
3. Install shims (18) and adapter (17). Adjust shims (18) to obtain an end play of
0.60 ± 0.20 mm (0.024 ± 0.008 inch).
4. Install bolts (22).
Illustration 2 g01403432
5. Attach a suitable lifting device to drawbar (1). Install drawbar (1). The weight of drawbar
(1) is approximately 907 kg (2000 lb).
6. Install bolts (16).
2/6
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 3 g01403404
7. Install shoe (14). Repeat for the remaining shoes.
8. Install bolts (13).
Note: Note the number of shims (15) and the location of shoes (14).
9. Tighten set screw (12).
10. Tighten nut (11).
Illustration 4 g01403392
11. Extend the blade lift cylinders.
12. Install cap (9) and the shims. Install bolts (10). Repeat this step for the opposite side of the
machine.
Note: Note the number of shims.
13. Install centershift cylinder (8). Refer to Disassembly and Assembly, "Centershift Cylinder -
Remove and Install".
3/6
140M Motor Grader B9M00001-UP (MACHINE)(SEBP4304 - 75) - Documentation
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...