The document provides instructions for installing a cylinder head on a 120G Motor Grader with a 3304 engine. It describes 16 steps for the installation including cleaning surfaces, installing gaskets and bolts, tightening bolts in a specific sequence, adjusting valves, and reinstalling related components. It also includes summaries for removing and installing the spacer plate and water directors.
Caterpillar cat 120 g motor grader (prefix 87v) service repair manual (87v083...fjsjjekdkme
The document provides instructions for installing a cylinder head on a 120G motor grader with a 3304 engine. It involves 16 steps: cleaning and preparing surfaces, installing gaskets and bolts, tightening bolts in a specific sequence, adjusting valves, and installing related components like intake pipes and hoses. The instructions emphasize keeping parts clean to prevent wear and include illustrations to clarify steps.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v005...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v020...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 16 g motor grader (prefix 93u) service repair manual (93u0267...fjsekdmmeed
This document provides instructions for removing and installing rocker shaft assemblies, push rods, valve lifters, and related components on a 3406C diesel engine. The key steps include:
1. Removing the valve covers, fuel lines, rocker shaft assemblies, push rods, and valve lifters. Identification marks should be made on removed parts.
2. Cleaning and lubricating replacement parts as needed before installation. Parts should be installed in their original locations when possible.
3. Installing the valve lifters, push rods, rocker shaft assemblies, fuel lines, adjusting the valves, and replacing the valve covers. Torque specifications and safety notices are provided throughout.
Caterpillar cat 16 h motor grader (prefix ats) service repair manual (ats0000...fjskefkemms
This document provides disassembly instructions for the transmission and transfer gears of a 16H Motor Grader. It lists over 60 steps and required tools to disassemble components such as the transmission control module, planetary group, sleeves, gears, bearings, seals, and housing. Detailed illustrations accompany each step to show how to remove parts and subassemblies like the gear pump, coupling assembly, manifold, and housing. Safety precautions are provided for steps involving compressed springs.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar cat 120 g motor grader (prefix 87v) service repair manual (87v083...fjsjjekdkme
The document provides instructions for installing a cylinder head on a 120G motor grader with a 3304 engine. It involves 16 steps: cleaning and preparing surfaces, installing gaskets and bolts, tightening bolts in a specific sequence, adjusting valves, and installing related components like intake pipes and hoses. The instructions emphasize keeping parts clean to prevent wear and include illustrations to clarify steps.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v005...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v020...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 16 g motor grader (prefix 93u) service repair manual (93u0267...fjsekdmmeed
This document provides instructions for removing and installing rocker shaft assemblies, push rods, valve lifters, and related components on a 3406C diesel engine. The key steps include:
1. Removing the valve covers, fuel lines, rocker shaft assemblies, push rods, and valve lifters. Identification marks should be made on removed parts.
2. Cleaning and lubricating replacement parts as needed before installation. Parts should be installed in their original locations when possible.
3. Installing the valve lifters, push rods, rocker shaft assemblies, fuel lines, adjusting the valves, and replacing the valve covers. Torque specifications and safety notices are provided throughout.
Caterpillar cat 16 h motor grader (prefix ats) service repair manual (ats0000...fjskefkemms
This document provides disassembly instructions for the transmission and transfer gears of a 16H Motor Grader. It lists over 60 steps and required tools to disassemble components such as the transmission control module, planetary group, sleeves, gears, bearings, seals, and housing. Detailed illustrations accompany each step to show how to remove parts and subassemblies like the gear pump, coupling assembly, manifold, and housing. Safety precautions are provided for steps involving compressed springs.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 219 d excavator (prefix 5xg) service repair manual (5xg00001 ...fjskekdmjekm
The document provides instructions for removing and installing various engine components of a 219D Excavator, including the cylinder head, spacer plate, and water directors. It describes removing components like bolts, gaskets and seals in a specific order. Installation is the reverse of removal, applying new gaskets and torquing bolts to the specified values. Precautions are given to keep components clean and contain fluids.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 120 g motor grader (prefix 87v) service repair manual (87v083...fjsekkdmmmse
1. The document provides instructions for removing and installing a camshaft on a 3304 engine. It describes using lifting devices and magnets to remove the camshaft and install a new one, being careful to keep parts clean from contaminants.
2. Specific steps include removing the valve lifters, loosening camshaft bolts, lifting out the camshaft, cleaning surfaces, applying lubricant to the camshaft, and lowering it back into place.
3. Proper torque values are given for tightening camshaft bolts during installation.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v005...fjjsekkdmme
This document provides instructions for installing a cylinder head on a Caterpillar 3304 engine. It describes 15 steps for the installation, including cleaning and lubricating surfaces, positioning the cylinder head and installing bolts, installing pushrods and adjusting valve clearance, and attaching related components like intake pipes and water lines. Torque specifications are provided for tightening the cylinder head bolts and rocker arm bolts. The instructions also note that a new spacer plate gasket must be installed when removing and reinstalling the cylinder head.
Caterpillar Cat 12H Motor Grader (Prefix 5ZM) Service Repair Manual Instant D...hean57759707
The document provides instructions for installing a cylinder head on a 12H Motor Grader with a 3306 engine. It describes cleaning the cylinder head and block mating surfaces, installing a new gasket and tightening the head bolts in a specific sequence. It also covers installing pushrods, rocker arms, inlet and outlet components before adjusting the valves. The process is completed by installing covers and connecting lines.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...dkdmidkkdk
The document provides instructions for installing the cylinder head on a 130G MOTOR GRADER with a 3304 engine. The instructions include: cleaning and preparing the cylinder head and block mating surfaces, installing a new gasket and tightening the head bolts in a specific sequence, installing related components like pushrods and rocker arms, adjusting valve lash, and reinstalling intake and cooling system components. Separate instructions are also provided for installing the spacer plate and water directors.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v020...fjjsekkdmme
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjjsekkdmme
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. It describes using lifting devices and clean lubricant to remove the camshaft and install a new one.
2. Specific steps include removing the valve lifters, loosening the camshaft bearing caps, and using lifting devices to raise the camshaft out of the engine. The installation is the reverse, applying lubricant and lowering the new camshaft into place.
3. Precautions are given to keep all parts clean and apply lubricant to prevent damage and wear.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...dkdmidkkdk
This document provides instructions for removing and installing the cylinder head and spacer plate on a Caterpillar 130G motor grader. The removal process involves disconnecting various components like fuel lines, exhaust manifolds, and pushrods. The cylinder head is then removed using lifting devices. For installation, the gaskets and cylinder head are positioned and bolted down in a specific tightening sequence. The pushrods, rocker arms, and other parts are then reinstalled. Adjustments are made to valve lash clearances before securing remaining components.
Massey ferguson mf 31 xp combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combines, including Perkins A6.354.4 engines. It contains lists of engine parts with item numbers, part numbers, quantities and descriptions. Reference information is also provided for various engine components that are not serviced individually.
Massey ferguson mf 31 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combines, including Perkins A6.354.4 engines. It consists of multiple sections covering the engine description, cylinder block, crankshaft, pistons, connecting rods, cylinder head and their respective components listed by item number, part number, quantity and description with notes.
Massey ferguson mf 29 xp combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides part numbers and descriptions for components of Massey Ferguson MF 24/27/29/29 XP/31/31 XP combine engines made by Perkins. It includes detailed lists and diagrams of engine parts such as the cylinder block, crankshaft, pistons, connecting rods, cylinder head and other internal components. Each part is numbered and specifications are provided.
Massey ferguson mf 265 tractor, 193552 (gb) parts catalogue manualkdidkdkkd
The document provides parts information for a Massey Ferguson MF 265 tractor engine. It includes 36 numbered items with corresponding part numbers, quantities, descriptions, and comments. The parts are grouped into sections for the cylinder block, cylinder head, crankshaft, pistons, timing gears, and other engine components. Measurements are provided in both inches and millimeters for some part thicknesses.
Massey ferguson mf 29 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combines, including Perkins A6.354.4 engines. It contains lists of engine parts with item numbers, part numbers, quantities and descriptions. Reference information and notes are also provided on various engine components.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 219 d excavator (prefix 5xg) service repair manual (5xg00001 ...fjskekdmjekm
The document provides instructions for removing and installing various engine components of a 219D Excavator, including the cylinder head, spacer plate, and water directors. It describes removing components like bolts, gaskets and seals in a specific order. Installation is the reverse of removal, applying new gaskets and torquing bolts to the specified values. Precautions are given to keep components clean and contain fluids.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 120 g motor grader (prefix 87v) service repair manual (87v083...fjsekkdmmmse
1. The document provides instructions for removing and installing a camshaft on a 3304 engine. It describes using lifting devices and magnets to remove the camshaft and install a new one, being careful to keep parts clean from contaminants.
2. Specific steps include removing the valve lifters, loosening camshaft bolts, lifting out the camshaft, cleaning surfaces, applying lubricant to the camshaft, and lowering it back into place.
3. Proper torque values are given for tightening camshaft bolts during installation.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v005...fjjsekkdmme
This document provides instructions for installing a cylinder head on a Caterpillar 3304 engine. It describes 15 steps for the installation, including cleaning and lubricating surfaces, positioning the cylinder head and installing bolts, installing pushrods and adjusting valve clearance, and attaching related components like intake pipes and water lines. Torque specifications are provided for tightening the cylinder head bolts and rocker arm bolts. The instructions also note that a new spacer plate gasket must be installed when removing and reinstalling the cylinder head.
Caterpillar Cat 12H Motor Grader (Prefix 5ZM) Service Repair Manual Instant D...hean57759707
The document provides instructions for installing a cylinder head on a 12H Motor Grader with a 3306 engine. It describes cleaning the cylinder head and block mating surfaces, installing a new gasket and tightening the head bolts in a specific sequence. It also covers installing pushrods, rocker arms, inlet and outlet components before adjusting the valves. The process is completed by installing covers and connecting lines.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...dkdmidkkdk
The document provides instructions for installing the cylinder head on a 130G MOTOR GRADER with a 3304 engine. The instructions include: cleaning and preparing the cylinder head and block mating surfaces, installing a new gasket and tightening the head bolts in a specific sequence, installing related components like pushrods and rocker arms, adjusting valve lash, and reinstalling intake and cooling system components. Separate instructions are also provided for installing the spacer plate and water directors.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v020...fjjsekkdmme
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjjsekkdmme
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. It describes using lifting devices and clean lubricant to remove the camshaft and install a new one.
2. Specific steps include removing the valve lifters, loosening the camshaft bearing caps, and using lifting devices to raise the camshaft out of the engine. The installation is the reverse, applying lubricant and lowering the new camshaft into place.
3. Precautions are given to keep all parts clean and apply lubricant to prevent damage and wear.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...dkdmidkkdk
This document provides instructions for removing and installing the cylinder head and spacer plate on a Caterpillar 130G motor grader. The removal process involves disconnecting various components like fuel lines, exhaust manifolds, and pushrods. The cylinder head is then removed using lifting devices. For installation, the gaskets and cylinder head are positioned and bolted down in a specific tightening sequence. The pushrods, rocker arms, and other parts are then reinstalled. Adjustments are made to valve lash clearances before securing remaining components.
Similar to Caterpillar cat 120 g motor grader (prefix 87v) service repair manual (87v08360 and up) (7)
Massey ferguson mf 31 xp combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combines, including Perkins A6.354.4 engines. It contains lists of engine parts with item numbers, part numbers, quantities and descriptions. Reference information is also provided for various engine components that are not serviced individually.
Massey ferguson mf 31 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combines, including Perkins A6.354.4 engines. It consists of multiple sections covering the engine description, cylinder block, crankshaft, pistons, connecting rods, cylinder head and their respective components listed by item number, part number, quantity and description with notes.
Massey ferguson mf 29 xp combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides part numbers and descriptions for components of Massey Ferguson MF 24/27/29/29 XP/31/31 XP combine engines made by Perkins. It includes detailed lists and diagrams of engine parts such as the cylinder block, crankshaft, pistons, connecting rods, cylinder head and other internal components. Each part is numbered and specifications are provided.
Massey ferguson mf 265 tractor, 193552 (gb) parts catalogue manualkdidkdkkd
The document provides parts information for a Massey Ferguson MF 265 tractor engine. It includes 36 numbered items with corresponding part numbers, quantities, descriptions, and comments. The parts are grouped into sections for the cylinder block, cylinder head, crankshaft, pistons, timing gears, and other engine components. Measurements are provided in both inches and millimeters for some part thicknesses.
Massey ferguson mf 29 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combines, including Perkins A6.354.4 engines. It contains lists of engine parts with item numbers, part numbers, quantities and descriptions. Reference information and notes are also provided on various engine components.
Massey ferguson mf 375 tractor, b18008 parts catalogue manualkdidkdkkd
The document contains parts lists and descriptions for various components of a Massey Ferguson MF 375 tractor, including the engine, cylinder block, crankshaft, pistons, connecting rods, and cylinder head. It lists over 50 individual parts by number, quantity, description, and other identifying information like serial numbers. The parts are grouped into sections based on the mechanical system or component they belong to.
Massey ferguson mf 362 n tractor (japan only) parts catalogue manualkdidkdkkd
This document provides specifications and part numbers for a Massey Ferguson 362 N tractor intended for the Japanese market. It includes detailed parts lists and diagrams for the engine, cylinder block, crankshaft, pistons, cylinder head, and rocker shaft. Reference numbers are provided for ordering replacement parts.
Massey ferguson mf 390 tractor, b18008 parts catalogue manualkdidkdkkd
This document provides parts information for an MF 390 tractor engine. It includes:
1) A list of engine parts with part numbers and descriptions
2) Serial number ranges and other specifications for some parts
3) Notes on part replacements and specifications for different countries/models
Massey ferguson mf 398 tractor, b18008 parts catalogue manualkdidkdkkd
This document provides a parts list for a Massey Ferguson 398 tractor engine. It includes 33 items related to the cylinder block, including the cylinder block itself, bearings, liners, plugs, bushes, gaskets, and housings. Each part is listed with its part number, quantity, description, and any relevant comments.
Massey ferguson mf 27 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on Massey Ferguson combine engines, including Perkins A6.354.4 engines used in MF 24, 27, 29, 29 XP, 31, and 31 XP combines. It lists over 100 individual parts that make up the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, and other components. Each part is given a reference number, part number, quantity used, description, and any relevant comments.
Massey ferguson mf 24 combine parts catalogue manualkdidkdkkd
This document provides the parts list and diagrams for a Massey Ferguson MF 24 combine with the model number 819723. It includes detailed lists and diagrams of parts for the straw divider, knives and fingers, wearing plates and stone stop, counter shaft, guarding, and feeder drum systems. Over 50 individual parts are specified by part number, quantity, description and placement in the various systems.
Massey ferguson mf 24 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combine harvesters, including part numbers, quantities and descriptions of engine components. It lists over 100 individual parts that make up engines, such as the cylinder block, crankshaft, pistons, connecting rods, cylinder head and their corresponding part numbers.
This document provides specifications and dimensions for 'NEF' diesel engines including 3 and 4 cylinder configurations. It describes the lubrication, cooling and turbocharging systems. Dimensions are given for engine blocks, crankshafts, cylinder heads, valves, camshafts and other components. Torque settings are also provided for many engine fasteners.
This document provides specifications and dimensions for 'NEF' diesel engines, including 3 and 4 cylinder models. It describes the engine components such as the injection pumps, lubrication system, cooling system, turbocharger, dimensions, and torque settings. The lubrication system uses a lobe oil pump to circulate oil through the crankshaft, camshaft, cylinder head and oil cooler. The cooling system has a water pump, radiator, thermostat and oil cooler. Turbocharged models include an air filter and turbocharger. Dimensions are provided for piston rings, bearings, valves, camshafts and other components. Torque settings are listed for engine attachment points.
This document provides specifications and dimensions for 'NEF' diesel engines, including 3 and 4 cylinder models. It describes the engine components such as the injection pumps, lubrication system, cooling system, turbocharger, dimensions, and torque settings. The lubrication system uses a lobe oil pump to circulate oil through the crankshaft, camshaft, cylinder head and oil cooler. The cooling system has a water pump, radiator, thermostat and oil cooler. Turbocharged models include an air filter and turbocharger. Dimensions are provided for pistons, cylinders, bearings, valves and other components. Torque settings are listed for various engine fasteners.
Claas nectis ve 237 2+4 wd (type t14) tractor service repair manualkdidkdkkd
1) The document provides identification information for injector pumps used on various tractor models, including the engine, number of cylinders, injector pump model, and injection sequence.
2) It describes the components and operation of the fuel injection system, including the fuel tank, lines, filter, pump, injectors and electrical components like sensors and solenoids.
3) Checks and adjustments are described for components like the accelerator control, injector pump timing, injectors, supply pressure and removal/refitting of the fuel filter. Torque settings and identification information is also provided.
Claas nectis ve 227 2+4 wd (type t14) tractor service repair manualkdidkdkkd
1. The document provides identification information for injector pumps and injectors used in various tractor models. It identifies the manufacturer, models, and specifications of the injector pumps and injectors.
2. The fuel injection system is described including the fuel tank, lines, filters, pump, and injectors. The operating principle and components of the injector pump are explained along with diagrams.
3. Torque settings and adjustment procedures are provided for the accelerator control and injector pump internal settings.
Claas nectis ve 217 2+4 wd (type t14) tractor service repair manualkdidkdkkd
1. The document provides identification information for injector pumps and injectors used in various tractor models. It identifies the manufacturer, models, and specifications of the injector pumps and injectors.
2. The document describes the components and operation of the fuel injection system, including the fuel tank, lines, filters, pump, injector pump, and injectors. It provides diagrams and explanations of how fuel is delivered to the injectors.
3. The document provides instructions for adjusting the accelerator control and setting the internal timing of the injector pump when removed from the engine. It describes the proper alignment and measurements needed for adjusting the pump timing.
Claas nectis f 267 2+4 wd (type t16) tractor service repair manualkdidkdkkd
This document provides specifications for Iveco NEF diesel engines, including 3 and 4 cylinder atmospheric and turbocharged models. It describes the engines' lubrication, cooling, and turbocharging systems. Dimensions are provided for pistons, crankshafts, cylinder heads, valves, and other components. Clearances and tolerances are indicated. The engines have mechanical injection pumps and use a pressurized lubrication system with an oil pump and filter. The closed-loop cooling system includes a water pump, radiator, and thermostat. Turbocharged versions get air from a compressor driven by the exhaust system.
Claas nectis f 257 2+4 wd (type t16) tractor service repair manualkdidkdkkd
This document provides specifications for Iveco NEF diesel engines, including 3 and 4 cylinder atmospheric and turbocharged models. It describes the engines' lubrication, cooling, and turbocharging systems. Dimensions are provided for pistons, crankshafts, cylinder heads, valves, and other components. Clearances and tolerances are indicated. The engines have mechanical injection pumps and use a pressurized lubrication system with an oil pump and filter. The closed-loop cooling system includes a water pump, radiator, and thermostat. Turbocharged versions get air from a compressor driven by the exhaust system.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120G MOTOR GRADER 87V
Configuration: 120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07489822
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: When the cylinder head is removed, a new spacer plate gasket must be installed. Refer to
Disassembly and Assembly, "Spacer Plate - Remove and Install".
1. Ensure that the surface of the cylinder head is clean and dry. Install a new dry cylinder head
gasket onto the cylinder block.
Illustration 1 g00541495
1/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Fasten the proper lifting device to cylinder head (1). Put cylinder head (1) in position on the
cylinder block. Remove the lifting device after cylinder head (1) is positioned.
Illustration 2 g00541497
3. Apply clean engine oil to the threads and the washer faces of cylinder head bolts (2) and (3).
Install cylinder head bolts (2) and (3). Tighten the cylinder head bolts finger tight.
Note: Do not tighten the cylinder head bolts at this time.
Illustration 3 g00511493
4. Install pushrods (4). Make sure that the pushrods are installed in the original location and
that the pushrods are seated correctly in the valve lifters.
5. Loosen the adjusting screws on rocker arms (5) for valve clearance. This will prevent a bent
valve or a broken pushrod during installation.
6. Install a new O-ring seal in the rear rocker arm support.
7. Apply clean engine oil to all the rocker shaft bolts except bolt (25). Refer to illustration 5.
8. Put rocker shaft assembly (5) in position on the cylinder head. Make sure that the dowels in
the rocker shaft supports are aligned with the dowel holes in the cylinder head.
9. Ensure that the rocker arms are aligned with the pushrods and install the rocker shaft
mounting bolts. Tighten the rocker shaft mounting bolts finger tight.
2/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00602759
3304B torque sequence
10. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 18) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 18) again in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 18) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through E) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
3/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00328807
3306B torque sequence
11. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 26) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through G) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
12. Adjust the inlet valve lash to 0.38 mm (.015 inch) and the exhaust valve lash to 0.64 mm
(.025 inch). Tighten the locknuts for the adjusting screws to a torque of 29 ± 7 N·m
(22 ± 5 lb ft). Refer to the Testing and Adjusting, "Air Inlet and Exhaust System" topic for
additional information on valve lash adjustments.
Illustration 6 g00511911
13. Put the gasket and air inlet pipe (7) in position on the cylinder head. Install four bolts (6) to
fasten air inlet pipe (7) to the cylinder head.
Illustration 7 g00541522
4/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 14. Connect tube (8) to the inlet manifold.
Illustration 8 g00541524
15. Put the gaskets and water pump elbow (11) in position on the engine. Install two bolts (9)
that fasten water pump elbow (11) to the cylinder head. Install two bolts (10) that fasten
water pump elbow (11) to the water pump.
Illustration 9 g00541527
16. Tighten hose clamp (12).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
b. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
c. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 19 00:29:46 UTC+0800 2020
5/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120G MOTOR GRADER 87V
Configuration: 120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01045029
Spacer Plate - Remove and Install
SMCS - 1221-010
Removal Procedure
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00540847
1/4
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 1. Remove O-ring seal (1), water seals (3) and water directors (4) from spacer plate (2) .
Illustration 2 g00540857
NOTICE
Do not damage the dowels as the spacer plate is removed.
2. Remove spacer plate (2) from the cylinder head.
Illustration 3 g00540895
3. Remove O-ring seal (6) and spacer plate gasket (5) from the cylinder head.
Installation Procedure
2/4
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the mating surfaces between the spacer plate and the cylinder block.
Illustration 4 g00540895
2. Install new spacer plate gasket (5) and new O-ring seal (6) .
Note: If the dowels in the cylinder block have been removed for any reason, the overall
height of the installation is 16.0 ± 5.0 mm (.63 ± .20 inch).
Illustration 5 g00540857
Note: Both surfaces of the spacer plate, spacer plate gasket and the top of the cylinder block
must be clean and dry. Do not use any gasket adhesive or other substances on these
surfaces.
3/4
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 3. Install spacer plate (2) on the cylinder head.
Illustration 6 g00540847
4. Install a new O-ring seal (1). Install new water seals (3). Install new water directors (4) .
5. Check the cylinder liner projection. Refer to Disassembly and Assembly, "Cylinder Liner -
Install".
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 19 00:30:42 UTC+0800 2020
4/4
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120G MOTOR GRADER 87V
Configuration: 120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00943364
Water Directors - Remove and Install
SMCS - 1115-010
Removal Procedure
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00481082
1/2
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 1. Remove water directors (1) from the cylinder head.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the cylinder head before assembly.
Illustration 2 g00481082
2. Install new water director (1) into the cylinder head. Align the notch in water director (1)
with the "V" mark on the cylinder head.
3. Install water director (1) to a depth of 0.8 ± 0.6 mm (0.031 ± 0.023 inch) below the surface
of the cylinder head.
End By: Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 19 00:31:38 UTC+0800 2020
2/2
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120G MOTOR GRADER 87V
Configuration: 120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01042782
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00538891
1. Use Tool (A) to remove valve lifter (1), as shown. Put identification marks on the valve
lifters for installation purposes.
2. Repeat Step 1 for the remainder of the valve lifters.
3. Check the diameter of the valve lifters. The diameter of a new valve lifter must be 33.285 ±
0.015 mm (1.3105 ± 0.0005 inch). The diameter of the bore in the cylinder block for a new
valve lifter must be 33.388 ± 0.050 mm (1.3145 ± 0.0020 inch). The maximum permissible
clearance between the valve lifter and the valve lifter bore in the cylinder block must be
0.30 mm (0.012 inch).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Illustration 2 g00538891
2/3
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Put 8T-2998 Lubricant on valve lifter (1) prior to installation. Install valve lifter (1) with
Tool (A) in the original location in the cylinder block.
2. Repeat Step 1 for the remainder of the valve lifters.
End By: Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 19 00:32:34 UTC+0800 2020
3/3
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120G MOTOR GRADER 87V
Configuration: 120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01037991
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
A. Remove the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
B. Remove the timing gear cover. Refer to Disassembly and Assembly, "Front Housing -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00476744
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. The "C" mark on
the crankshaft gear will be aligned with the "C" mark on the camshaft gear.
Illustration 2 g00476743
Note: Put a mark on the teeth of the fuel injection pump drive gear and the idler gear at
location (A). This will help to keep the engine timing correct during the removal and the
installation of the camshaft. Put a mark on the teeth of the idler gear and camshaft gear (2)
at location (B). When the camshaft is installed, the engine timing will be correct when the
mark at location (A) is aligned with the mark at location (B) and the "C" mark on the
crankshaft gear is aligned with the "C" mark on the camshaft gear.
2. Remove the bolts, the lock and washer (1) .
Illustration 3 g00535590
2/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. NOTICE
Do not damage the lobes or the bearings when the camshaft is
removed.
3. Carefully remove camshaft (3) from the engine.
4. If necessary, remove the bolts that hold camshaft drive gear (2) to the camshaft and remove
the gear.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00535590
1. Put camshaft drive gear (2) in position on the end of camshaft (3). Install the bolts that hold
camshaft drive gear (2) to camshaft (3). Tighten the bolts to a torque of 55 ± 7 N·m (41 ± 5
lb ft).
NOTICE
Do not damage the lobes or the bearings when the camshaft is installed.
3/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 2. Put 8T-2998 Camshaft Lubricant on the camshaft lobes only and put clean engine oil on the
bearing journals.
Note: During the installation of camshaft (3), rotate the camshaft in both directions in order
to prevent binding in the camshaft bearing bores.
3. Carefully install camshaft (3) into the engine.
Illustration 5 g00476743
Illustration 6 g00476744
4. Make sure that the mark on the teeth of the fuel injection pump drive gear and the idler gear
are in alignment at location (A). Make sure that the mark on the teeth of the idler gear and
camshaft gear (2) are in alignment at location (B). Align the "C" marks on the crankshaft
gear and camshaft gear (2). When all of the timing marks are in alignment the engine timing
is correct.
4/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 5. Install washer (1), the lock and the two bolts that hold the camshaft in position in the
engine.
End By:
a. Install the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
b. Install the timing gear cover. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 19 00:33:29 UTC+0800 2020
5/5
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120G MOTOR GRADER 87V
Configuration: 120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02473351
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. Remove the Flywheel Housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
B. Remove the Oil Pan Plate. Refer to Disassembly and Assembly, "Oil Pan Plate - Remove
and Install".
C. Remove the Camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g00478567
1. Use Tool (A) to remove the camshaft bearing from the cylinder block. Start with the front
bearings and work to the rear bearing.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g00478567
1. Use Tool (A) to install the camshaft bearings in the 3304B and 3306B cylinder block.
Note: The camshaft bearings in the 3304B have pressure lubrication. The intermediate
camshaft bearings and the rear camshaft bearings in the 3306B have splash lubrication.
2. Install the camshaft bearings in the 3304B cylinder block, as follows:
(a) Install the front bearing to a depth of 0.57 ± 0.5 mm (0.022 ± 0.02 inch). Ensure that the
oil holes are in a horizontal position and that the camshaft bearing joint is at the top of the
engine. The camshaft bearing joint can not be more than 15° degrees from vertical in either
direction.
(b) Install the center bearing to a depth of 303.2 ± 0.5 mm (11.94 ± 0.02 inch). Ensure that
the oil holes in the camshaft bearing are in alignment with the oil holes in the cylinder
block.
(c) Install the rear bearing to a depth of 604.9 ± 0.5 mm (23.81 ± 0.02 inch). Ensure that the
oil holes in the camshaft bearing are in alignment with the oil holes in the cylinder block.
Illustration 3 g00478822
1. Install the camshaft bearings in the 3306B cylinder block, as follows:
2. Install front bearing (B) to a depth of 0.5 ± 0.5 mm (.02 ± .02 inch). Ensure that the oil holes
are in a horizontal position and that the camshaft bearing joint is at the top of the engine.
The camshaft bearing joint cannot be more than 15 degrees from the vertical position in
either direction.
3. Install the remainder of the bearings. Install the bearings to the dimensions that are given
from the front face of the cylinder block: (C) 154.0 ± 0.5 mm (6.06 ± .02 inch), (D) 303.2 ±
3/4
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 0.5 mm (11.94 ± .02 inch), (E) 601.7 ± 0.5 mm (23.69 ± .02 inch) and (F) 903.4 ± 0.5 mm
(35.57 ± .02 inch).
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
b. Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate -
Remove and Install".
c. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 19 00:34:25 UTC+0800 2020
4/4
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120G MOTOR GRADER 87V
Configuration: 120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00974130
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1. Drain the engine oil from the engine into a suitable container for storage or disposal.
1/3
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g00541041
2. Loosen nut (4) and move the overflow tube away from the oil level gauge guide. Loosen nut
(3) and remove the oil level gauge guide from the engine.
3. Remove bolts (1) and the washers that hold the engine oil pan in position. Remove engine
oil pan (2) and the gasket from the engine oil pan plate.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00541041
1. Put the gasket and engine oil pan (2) in position on the engine oil pan plate. Install bolts (1)
and the washers that hold the engine oil pan in position.
2/3
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine(SEBP1...
2020/4/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...