This document is a service manual for Case IH WD1904 and WD2304 self-propelled windrowers with engine number PIN YGG677501 and above. It contains information on maintenance and repair for the engine, front and rear axles, hydrostatic drive, brakes, hydraulic systems, frames, steering, wheels, cab climate control, electrical systems, platform, cab, and decals. Safety precautions are provided and the manual instructs only qualified dealership personnel to perform repairs using the proper tools and procedures.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...ufjjsjekkeidol
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems and components.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...udjjskekmdmd
This document is a service manual for a self-propelled windrower (WD1504 Tier 4B) made by Case IH. It contains sections on the engine, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, wheels, cab climate control, and electrical systems. The manual provides repair and maintenance instructions for technicians, and warns that only qualified dealership personnel should perform such work using the specified procedures and tools.
Case sv300 tier 4b (final) alpha series skid steer loader service repair manu...udjjdjkksmme
This document is a service manual for Case skid steer loaders and compact track loaders with Tier 4B engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. Safety information is provided at the beginning regarding servicing equipment and personal safety precautions when working on the machines. Torque specifications and hydraulic standards are also listed, along with basic instructions for shop work and preventing hydraulic contamination. Machine identification and orientation are defined to identify the specific models covered.
Case tr310 tier 4 b (final) alpha series compact track loader service repair ...fujdfjjskkkemw
This document is a service manual that provides instructions and specifications for servicing Case construction equipment, including skid steer loaders and compact track loaders. It contains sections on the engine, power coupling, front and rear axles, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. The document provides standard torque specifications for hydraulics and minimum tightening torques for normal assembly. It also includes safety rules and notices for working on the equipment.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...fjeisldkmemm
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems and components.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...ufjskekfmsme
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems, with links to more specific subsections.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...usjefjkekmem
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems and components.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...fjskekqaswdmmem
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems and components.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...ufjjsjekkeidol
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems and components.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...udjjskekmdmd
This document is a service manual for a self-propelled windrower (WD1504 Tier 4B) made by Case IH. It contains sections on the engine, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, wheels, cab climate control, and electrical systems. The manual provides repair and maintenance instructions for technicians, and warns that only qualified dealership personnel should perform such work using the specified procedures and tools.
Case sv300 tier 4b (final) alpha series skid steer loader service repair manu...udjjdjkksmme
This document is a service manual for Case skid steer loaders and compact track loaders with Tier 4B engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. Safety information is provided at the beginning regarding servicing equipment and personal safety precautions when working on the machines. Torque specifications and hydraulic standards are also listed, along with basic instructions for shop work and preventing hydraulic contamination. Machine identification and orientation are defined to identify the specific models covered.
Case tr310 tier 4 b (final) alpha series compact track loader service repair ...fujdfjjskkkemw
This document is a service manual that provides instructions and specifications for servicing Case construction equipment, including skid steer loaders and compact track loaders. It contains sections on the engine, power coupling, front and rear axles, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. The document provides standard torque specifications for hydraulics and minimum tightening torques for normal assembly. It also includes safety rules and notices for working on the equipment.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...fjeisldkmemm
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems and components.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...ufjskekfmsme
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems, with links to more specific subsections.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...usjefjkekmem
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems and components.
Case ih wd1504 tier 4 b (final) self propelled windrower service repair manua...fjskekqaswdmmem
This document provides service information for a Tier 4B self-propelled windrower, including:
- Procedures for replacing the primary and secondary air filters on the engine.
- A test of the fuel injection system to check for fuel inlet restrictions or air entering the system by installing pressure gauges and observing fuel pressure at idle and under load.
- Sections covering various engine, drivetrain, hydraulic, electrical, and cab systems and components.
New holland l215 200 series skid steer loader service repair manualfjsekkmmme
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders, covering models C227, C232, C238, L213, L215, L218, L220, L223, L225, and L230. The manual contains sections on hydraulic, pneumatic, electrical and electronic systems, engines and PTO systems, transmissions, axles, brakes, steering, frames, cabs, user controls, positioning, tool attachment, hitching, digging and landscaping functions. Safety precautions and general specifications such as welding instructions are provided at the beginning.
New holland l213 200 series skid steer loader service repair manualfjsekkmmme
This document is a service manual for New Holland construction equipment models C227, C232, C238, L213, L215, L218, L220, L223, L225, and L230. It contains instructions for testing and installing the primary hydraulic pump. The test procedure involves using a flowmeter to measure pump output at various pressures and engine speeds. Installation involves aligning the pump splines with the coupling and securing it with bolts using Loctite.
Hyster d470 (n40 zr) forklift service repair manualfjsekkmmme
- The document provides repair instructions for various components on a forklift truck frame, including covers, panels, and plates, load wheels, and general safety warnings.
- Key components that can be repaired include the front frame panels, operator compartment cover, drive unit compartment door, various pads, and caster wheel cover. Instructions are provided for removing and installing these parts.
- Load wheel removal instructions include removing the nut, washers, axle bolt, and then pressing or tapping the bearings and axle sleeves from the load wheels using a soft punch and hammer to avoid damage.
Cummins onan generator set with power command 3100 controller model (dqbb) se...fjsekkmmme
This document is a service manual that provides information for troubleshooting and servicing generator sets and their PowerCommand 3100 controllers. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank and optional enclosure fuel tank systems, and wiring diagrams. The manual contains important safety instructions and details the generator set models and specifications that it covers.
Cummins onan generator set with power command 3100 controller model (dfce ) s...fjsekkmmme
This document is a service manual that provides information for troubleshooting and servicing generator sets and their PowerCommand 3100 controllers. It includes sections that cover control operation, circuit boards and modules, troubleshooting procedures, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual contains important safety instructions and provides detailed technical information, component specifications, and repair and maintenance procedures.
Cummins onan generator set with power command 3100 controller model (dfaa ) s...fjsekkmmme
This document is a service manual that provides information for troubleshooting and servicing generator sets and their PowerCommand 3100 controllers. It includes sections that cover control operation, circuit boards and modules, troubleshooting procedures, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual contains important safety instructions and provides detailed technical information, component specifications, and repair and maintenance procedures.
Cummins onan gea series generator sets service repair manualfjsekkmmme
This document provides an overview of the components and operation of AC and DC control systems for GEA Series generator sets. It describes the main components of the AC control panel including the control box and voltage regulator. It also outlines the components of the DC control panel such as sensors, switches and printed circuit boards that control engine operation. Troubleshooting guides are provided for issues like the engine not starting or output voltage problems. Safety precautions for working with fuel, batteries and electrical systems are listed.
Cummins onan dqcc generator set with qsk23 g3 engine and power command 2100 c...fjsekkmmme
This document is a service manual that provides instructions for operating, troubleshooting, and servicing a generator set with a QSK23G3 engine and PowerCommand 2100 controller. It contains sections on control operation, circuit boards and modules, troubleshooting, control adjustment and service, servicing the generator, an optional enclosure fuel tank system, and wiring diagrams. The manual provides technical specifications and safety guidelines for working on the generator set.
Case tv380 tier 4 b (final) alpha series compact track loader service repair ...fjsekkmmme
This document is a service manual that provides maintenance and repair instructions for SR270/SV340 skid steer loaders and TR340/TV380 compact track loaders with Tier 4B engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. Safety information and instructions are provided at the beginning, along with information on torque specifications, basic shop and assembly instructions, fluids and lubricants, and product identification. Repair and maintenance should only be performed by qualified
New holland stack cruiser 102 tier 4b (final) bale wagon service repair manua...fjsekkmmme
This service manual provides information for servicing the StackCruiser 102, 103, and 105 self-propelled bale wagons. The document includes sections on the engine, transmission, axles, brakes, hydraulic systems, frames, steering, wheels, climate control, electrical systems, bale handling components, lubrication systems, and other parts. It provides maintenance and repair instructions referenced by section number, along with technical specifications and safety information.
New holland speedrower 200 self propelled windrower service repair manualfjsekkmmme
This document is a service manual for Speedrower 200 and 240 self-propelled windrowers. It contains part numbers, product and engine links, contents sections, and safety rules for operating and servicing the machines. Safety is emphasized, including warnings about operating on slopes, carrying passengers, impaired operation, overhead hazards, and risks of fluid penetration.
New holland speedrower 160 tier 4 b (final) self propelled windrower service ...fjsekkmmme
This document provides service information for a Speedrower 160 self-propelled windrower, including:
- The engine is a 4-cylinder turbocharged and aftercooled unit that meets Tier 4B emission regulations.
- Procedures for checking, adding, and draining engine oil, including identifying the location of the dipstick, fill cap, and drain plug.
- Instructions for replacing the oil filter, including applying a film of oil to the new filter's seal before installation.
- Recommendations to clean areas prior to removing caps or plugs to prevent contamination, and to allow the engine to warm before draining oil.
New holland speedrower 130 self propelled windrower service repair manualfjsekkmmme
The document provides service manual instructions for removing the engine from a Speedrower 130 self-propelled windrower. The steps include draining fluids, disconnecting cables, hoses, and linkages. Components like the radiator, fuel lines, intake tubes, and side doors are detached from the engine. Disconnecting the gas springs, bolts, and pivot clips allows the hood support frame and doors to be removed to access the engine.
New holland guardian sp.300 f tier 4b (final) sprayer service repair manual (...fjsekkmmme
This document is a service manual that provides instructions for removing and installing an engine on Guardian sprayer models SP.295F, SP.300F, SP.345F, and SP.400F. The removal process involves draining fluids, disconnecting lines and electrical connections, and removing mounting hardware. The installation is the reverse of removal, reconnecting all lines and mounting the engine securely. Safety precautions and procedures specific to the engine type are referenced.
New holland gt22 garden tractor service repair manualfjsekkmmme
This document provides specifications and maintenance information for Kohler CH18-25 gasoline engines used in garden tractors. It includes safety warnings, identification of major engine components, specifications on dimensions, torque and horsepower curves. Routine maintenance procedures are outlined, such as changing the oil and oil filter, storing the engine long-term, and a schedule of periodic maintenance. Torque specifications and values for major engine fasteners are also provided.
New holland 9184 tractor service repair manualfjsekkmmme
This document provides instructions for removing, inspecting, and installing components of the air induction system on 84 Series tractors, including the air induction tube, rubber boot, and precleaner. The removal process involves removing shields, the hood, and clamps before separating parts. Inspection checks for cracks or damage. Installation follows the reverse of removal procedures and ensures a proper seal.
New holland 5635 tractor service repair manualfjsekkmmme
This document is the contents page for a repair manual for a 35 Series Tractor covering models 4835, 5635, 6635, and 7635. The repair manual contains 11 sections covering general information, the engine, electrical system, high pressure hydraulic system, low pressure hydraulic system, power train, front axle, PTO, cab, air conditioning, and special tools. The manual was published in 1998 by New Holland North America.
Massey ferguson 5465 tractor (tier 3 perkins engine) service parts catalogue...fjsekkmmme
This document provides parts information for a Massey Ferguson 5465 tractor with a Perkins Tier 3 engine. It includes 34 labeled diagrams summarizing the main engine parts, including the cylinder block, timing gears, crankshaft, pistons, and connecting rods. Each diagram lists the part numbers, quantities, and brief descriptions for each component.
Massey ferguson 5460 tractor (tier 3 sisu engine) service parts catalogue man...fjsekkmmme
This document provides parts information for a Massey Ferguson 5460 tractor with a Tier 3 Sisu engine. It includes three pages of documentation with detailed lists of over 40 individual engine parts. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component. Footnotes provide additional information such as applicability based on serial number ranges.
Massey ferguson 4270 tractors ( k37009) service parts catalogue manual (part...fjsekkmmme
This document provides parts information for the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft, timing gear, and camshaft of Massey Ferguson 4260/4270 tractors. It contains detailed lists of over 40 individual parts that make up these core engine components, including part numbers, quantities, descriptions, and replacement part notes. Precision manufacturing information is provided, such as fit types for cylinder liners.
New holland l215 200 series skid steer loader service repair manualfjsekkmmme
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders, covering models C227, C232, C238, L213, L215, L218, L220, L223, L225, and L230. The manual contains sections on hydraulic, pneumatic, electrical and electronic systems, engines and PTO systems, transmissions, axles, brakes, steering, frames, cabs, user controls, positioning, tool attachment, hitching, digging and landscaping functions. Safety precautions and general specifications such as welding instructions are provided at the beginning.
New holland l213 200 series skid steer loader service repair manualfjsekkmmme
This document is a service manual for New Holland construction equipment models C227, C232, C238, L213, L215, L218, L220, L223, L225, and L230. It contains instructions for testing and installing the primary hydraulic pump. The test procedure involves using a flowmeter to measure pump output at various pressures and engine speeds. Installation involves aligning the pump splines with the coupling and securing it with bolts using Loctite.
Hyster d470 (n40 zr) forklift service repair manualfjsekkmmme
- The document provides repair instructions for various components on a forklift truck frame, including covers, panels, and plates, load wheels, and general safety warnings.
- Key components that can be repaired include the front frame panels, operator compartment cover, drive unit compartment door, various pads, and caster wheel cover. Instructions are provided for removing and installing these parts.
- Load wheel removal instructions include removing the nut, washers, axle bolt, and then pressing or tapping the bearings and axle sleeves from the load wheels using a soft punch and hammer to avoid damage.
Cummins onan generator set with power command 3100 controller model (dqbb) se...fjsekkmmme
This document is a service manual that provides information for troubleshooting and servicing generator sets and their PowerCommand 3100 controllers. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank and optional enclosure fuel tank systems, and wiring diagrams. The manual contains important safety instructions and details the generator set models and specifications that it covers.
Cummins onan generator set with power command 3100 controller model (dfce ) s...fjsekkmmme
This document is a service manual that provides information for troubleshooting and servicing generator sets and their PowerCommand 3100 controllers. It includes sections that cover control operation, circuit boards and modules, troubleshooting procedures, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual contains important safety instructions and provides detailed technical information, component specifications, and repair and maintenance procedures.
Cummins onan generator set with power command 3100 controller model (dfaa ) s...fjsekkmmme
This document is a service manual that provides information for troubleshooting and servicing generator sets and their PowerCommand 3100 controllers. It includes sections that cover control operation, circuit boards and modules, troubleshooting procedures, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual contains important safety instructions and provides detailed technical information, component specifications, and repair and maintenance procedures.
Cummins onan gea series generator sets service repair manualfjsekkmmme
This document provides an overview of the components and operation of AC and DC control systems for GEA Series generator sets. It describes the main components of the AC control panel including the control box and voltage regulator. It also outlines the components of the DC control panel such as sensors, switches and printed circuit boards that control engine operation. Troubleshooting guides are provided for issues like the engine not starting or output voltage problems. Safety precautions for working with fuel, batteries and electrical systems are listed.
Cummins onan dqcc generator set with qsk23 g3 engine and power command 2100 c...fjsekkmmme
This document is a service manual that provides instructions for operating, troubleshooting, and servicing a generator set with a QSK23G3 engine and PowerCommand 2100 controller. It contains sections on control operation, circuit boards and modules, troubleshooting, control adjustment and service, servicing the generator, an optional enclosure fuel tank system, and wiring diagrams. The manual provides technical specifications and safety guidelines for working on the generator set.
Case tv380 tier 4 b (final) alpha series compact track loader service repair ...fjsekkmmme
This document is a service manual that provides maintenance and repair instructions for SR270/SV340 skid steer loaders and TR340/TV380 compact track loaders with Tier 4B engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. Safety information and instructions are provided at the beginning, along with information on torque specifications, basic shop and assembly instructions, fluids and lubricants, and product identification. Repair and maintenance should only be performed by qualified
New holland stack cruiser 102 tier 4b (final) bale wagon service repair manua...fjsekkmmme
This service manual provides information for servicing the StackCruiser 102, 103, and 105 self-propelled bale wagons. The document includes sections on the engine, transmission, axles, brakes, hydraulic systems, frames, steering, wheels, climate control, electrical systems, bale handling components, lubrication systems, and other parts. It provides maintenance and repair instructions referenced by section number, along with technical specifications and safety information.
New holland speedrower 200 self propelled windrower service repair manualfjsekkmmme
This document is a service manual for Speedrower 200 and 240 self-propelled windrowers. It contains part numbers, product and engine links, contents sections, and safety rules for operating and servicing the machines. Safety is emphasized, including warnings about operating on slopes, carrying passengers, impaired operation, overhead hazards, and risks of fluid penetration.
New holland speedrower 160 tier 4 b (final) self propelled windrower service ...fjsekkmmme
This document provides service information for a Speedrower 160 self-propelled windrower, including:
- The engine is a 4-cylinder turbocharged and aftercooled unit that meets Tier 4B emission regulations.
- Procedures for checking, adding, and draining engine oil, including identifying the location of the dipstick, fill cap, and drain plug.
- Instructions for replacing the oil filter, including applying a film of oil to the new filter's seal before installation.
- Recommendations to clean areas prior to removing caps or plugs to prevent contamination, and to allow the engine to warm before draining oil.
New holland speedrower 130 self propelled windrower service repair manualfjsekkmmme
The document provides service manual instructions for removing the engine from a Speedrower 130 self-propelled windrower. The steps include draining fluids, disconnecting cables, hoses, and linkages. Components like the radiator, fuel lines, intake tubes, and side doors are detached from the engine. Disconnecting the gas springs, bolts, and pivot clips allows the hood support frame and doors to be removed to access the engine.
New holland guardian sp.300 f tier 4b (final) sprayer service repair manual (...fjsekkmmme
This document is a service manual that provides instructions for removing and installing an engine on Guardian sprayer models SP.295F, SP.300F, SP.345F, and SP.400F. The removal process involves draining fluids, disconnecting lines and electrical connections, and removing mounting hardware. The installation is the reverse of removal, reconnecting all lines and mounting the engine securely. Safety precautions and procedures specific to the engine type are referenced.
New holland gt22 garden tractor service repair manualfjsekkmmme
This document provides specifications and maintenance information for Kohler CH18-25 gasoline engines used in garden tractors. It includes safety warnings, identification of major engine components, specifications on dimensions, torque and horsepower curves. Routine maintenance procedures are outlined, such as changing the oil and oil filter, storing the engine long-term, and a schedule of periodic maintenance. Torque specifications and values for major engine fasteners are also provided.
New holland 9184 tractor service repair manualfjsekkmmme
This document provides instructions for removing, inspecting, and installing components of the air induction system on 84 Series tractors, including the air induction tube, rubber boot, and precleaner. The removal process involves removing shields, the hood, and clamps before separating parts. Inspection checks for cracks or damage. Installation follows the reverse of removal procedures and ensures a proper seal.
New holland 5635 tractor service repair manualfjsekkmmme
This document is the contents page for a repair manual for a 35 Series Tractor covering models 4835, 5635, 6635, and 7635. The repair manual contains 11 sections covering general information, the engine, electrical system, high pressure hydraulic system, low pressure hydraulic system, power train, front axle, PTO, cab, air conditioning, and special tools. The manual was published in 1998 by New Holland North America.
Massey ferguson 5465 tractor (tier 3 perkins engine) service parts catalogue...fjsekkmmme
This document provides parts information for a Massey Ferguson 5465 tractor with a Perkins Tier 3 engine. It includes 34 labeled diagrams summarizing the main engine parts, including the cylinder block, timing gears, crankshaft, pistons, and connecting rods. Each diagram lists the part numbers, quantities, and brief descriptions for each component.
Massey ferguson 5460 tractor (tier 3 sisu engine) service parts catalogue man...fjsekkmmme
This document provides parts information for a Massey Ferguson 5460 tractor with a Tier 3 Sisu engine. It includes three pages of documentation with detailed lists of over 40 individual engine parts. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component. Footnotes provide additional information such as applicability based on serial number ranges.
Massey ferguson 4270 tractors ( k37009) service parts catalogue manual (part...fjsekkmmme
This document provides parts information for the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft, timing gear, and camshaft of Massey Ferguson 4260/4270 tractors. It contains detailed lists of over 40 individual parts that make up these core engine components, including part numbers, quantities, descriptions, and replacement part notes. Precision manufacturing information is provided, such as fit types for cylinder liners.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
7. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your CASE IH Sales and Service Networks.
48143358 20/04/2017
3
8. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
48143358 20/04/2017
4
9. INTRODUCTION
Safety rules
General safety rules
Use caution when operating the machine on slopes. Raised equipment, full tanks and other loads will change
the center of gravity of the machine. The machine can tip or roll over when near ditches and embankments or
uneven surfaces.
• Only skilled operators who are familiar with all the controls and harvesting techniques should use the equipment.
It is recommended to operate on cultivated land with slopes no greater than 26% ( 15°) uphill and downhill.
• If necessary, when driving downhill change into a lower gear before starting the descent. Machine must be stopped
to downshift into a lower gear.
Never permit anyone other than the operator to ride on the machine.
Never operate the machine under the influence of alcohol, drugs, or while otherwise impaired.
Pay attention to overhead power lines and hanging obstacles. High voltage lines may require significant clearance
for safety.
Hydraulic oil or diesel fuel leaking under pressure can penetrate the skin, causing serious injury or infection.
• DO NOT use your hand to check for leaks. Use a piece of cardboard or paper.
• Stop engine, remove key and relieve the pressure before connecting or disconnecting fluid lines.
• Make sure all components are in good condition and tighten all connections before starting the engine or pressur-
izing the system.
• If hydraulic fluid or diesel fuel penetrates the skin, seek medical attention immediately.
• Continuous long term contact with hydraulic fluid may cause skin cancer. Avoid long term contact and wash the
skin promptly with soap and water.
Keep clear of moving parts. Loose clothing, jewelry, watches, long hair, and other loose or hanging items can become
entangled in moving parts.
Wear protective equipment when appropriate.
DO NOT attempt to remove material from any part of the machine while it is being operated or components are in
motion.
Make sure all guards and shields are in good condition and properly installed before operating the machine. Never
operate the machine with shields removed. Always close access doors or panels before operating the machine.
Dirty or slippery steps, ladders, walkways, and platforms can cause falls. Make sure these surfaces remain clean and
clear of debris.
A person or pet within the operating area of a machine can be struck or crushed by the machine or its equipment. DO
NOT allow anyone to enter the work area.
Raised equipment and/or loads can fall unexpectedly and crush persons underneath. Never allow anyone to enter
the area underneath raised equipment during operation.
Never operate engine in enclosed spaces as harmful exhaust gases may build up.
Before starting the machine, be sure that all controls are in neutral or park lock position.
Start the engine only from the operator’s seat. If the safety start switch is bypassed, the engine can start with the
transmission in gear. Do not connect or short across terminals on the starter solenoid. Attach jumper cables as
described in the manual. Starting in gear may cause death or serious injury.
Always keep windows, mirrors, all lighting, and Slow Moving Vehicle (SMV) emblem clean to provide the best possible
visibility while operating the machine.
48143358 20/04/2017
5
11. Engine - Air cleaners and lines
Replace primary (outer) air filter
The display will indicate when you must perform routine service for the air filter.
Replace both the outer and inner filters annually.
NOTICE: Do not clean the inner filter.
1. The air filter (1) is located under the right engine bay
door.
NHIL14WR00357AA 1
2. To remove the element, release the three latches (1).
3. Remove the hose clamp (2) on the bottom of the cover.
4. Remove the hose (3) from the cover.
5. Pull the cover off.
NHIL14WR00357AA 2
6. Pull the outer filter (1) out.
10041166 3
48143358 20/04/2017
10.1 [10.202] / 3
12. Engine - Air cleaners and lines
7. Clean the inside of the air cleaner housing and cover
using a damp, lint-free cloth.
NOTICE: Do not remove or disturb the inner element (1).
The inner element must be replaced if there is any sign of
dirt on it. The inner element should not be cleaned, but
only replaced.
10041167 4
8. Install the outer element (1). Push the element in all
the way.
10041166 5
9. Install the cover at the angle at which it was removed.
10. Secure the cover with the three latches (1).
11. Install the hose (3) back onto the cover.
12. Secure the hose to the cover with hose clamp (2).
NHIL14WR00357AA 6
48143358 20/04/2017
10.1 [10.202] / 4
13. Engine - Air cleaners and lines
Replace secondary (inner) air filter
The display will indicate when you must perform routine service for the air filter.
Replace both the outer and inner filters annually.
NOTICE: Do not clean the inner filter.
1. Remove the outer filter as described in Replace pri-
mary (outer) air filter (10.202) .
2. Pull the inner filter (1) out. Some wiggling may be nec-
essary.
3. Clean the inside of the air cleaner housing and the
cover with a damp, lint-free cloth.
4. Install the new inner filter. Push the filter in until it is
seated.
5. Install the outer filter and close the housing as de-
scribed in Replace primary (outer) air filter (10.202) .
10041425 1
48143358 20/04/2017
10.1 [10.202] / 5
14. Engine - Fuel injection system
Fuel injection system - Test
WD1904 Tier 3, Canada [YGG677501 - ] NA
Fuel inlet restriction/air entering system
BAIL08CVT128ASA 1
• (1) 380100057 0 – 11 bar (0 – 160 psi) gauge and hose assembly
• (2) 380100056 0 – 100 kPa / 0 – 30 in / HG, 0 – 200 kPa / 0 – 30 in PSI Gauge Assembly
• (A) From fuel tank
• (B) Return to fuel tank
NOTE: Use the contents of special tool 380140055 for these tests.
1. Install 380100056 at the inlet of the low pressure pump
(after the primary filter).
• This test line contains a compound gauge 0 –
762 mm (0 – 30 in) of Hg vacuum and 0 – 2.07 bar
(0 – 30 psi) positive pressure. This test line is con-
structed with clear tubing to allow observation for air
in the system.
• Operate the engine to purge air from the system
which entered during gauge installation.
2. Install 380100057 between the outlet of the fuel filter
and the inlet of the high pressure pump.
• This test line contains a pressure gauge 0 – 11 bar
(0 – 160 psi).
NOTE: The clear line could be left in place over night to
check for a slow air ingress leak.
48143358 20/04/2017
10.2 [10.218] / 3
15. Engine - Fuel injection system
3. When air is no longer visible in the clear test line, mea-
sure and record the operating pressure, while continu-
ally observing for air in the fuel. Fuel Pressure Specifi-
cation between Filter and High Pressure Pump: 5 bar
(72 psi) minimum. Conditions:
• ________Gauge 1 ________ Gauge 2: Low idle;
apply no load to the engine.
• ________Gauge 1 ________ Gauge 2: 1500 RPM
apply no load to the engine.
• ________Gauge 1 ________ Gauge 2: High idle;
apply load to the engine using the hydraulics (over
relief), hydrostatic stall, converter stall, or dy-
namometer. Load the engine to its rated rpm.
BAIL08CVT129FSA 2
• (1) 380100057 0 – 11 bar (0 – 160 psi) gauge and hose assembly
• (2) 380100056 0 – 100 kPa / 0 – 30 in / HG, 0 – 200 kPa / 0 – 30 in PSI Gauge Assembly
• (3) Primary Filter Outlet to Low Pressure Pump Inlet
• (4) High Pressure Pump Inlet from Fuel Filter Outlet
• (5) Secondary Fuel Filter (pressurized filter)
• (6) Secondary Fuel Filter Inlet (pressurized filter)
• (7) Primary Fuel Filter (suction filter)
48143358 20/04/2017
10.2 [10.218] / 4
16. Engine - Fuel injection system
4. If the fuel pressure at gauge (1) is below 5 bar (73 psi)
at any time during the test, check or replace the follow-
ing as needed:
• Fuel Pre-filter (if equipped). Some applications do
not use a fuel pre-filter.
• Primary Fuel Filter
• The lines and connections from the fuel supply pump
inlet back to the fuel tank, checking for damaged
lines (kinks create restriction; rub marks may allow
air to enter) and leakage at the Voss o-ring fittings.
• Fuel tank, clean as required.
• The fuel pick-up tube in the fuel tank. Check for
cracks, plugging, or contact with the bottom/side-
walls of the tank.
• The fuel tank cap. Be sure a vacuum is not being
formed in the fuel tank. A vacuum at the tank would
reduce the fuel supply pressure to the injection fuel
pump inlet. Vacuum in the fuel tank might not be
observable during short-term running.
• Check the valve at the fuel tank outlet (if equipped).
Ensure that fuel supplied to and from the valve as-
sembly is properly connected.
48143358 20/04/2017
10.2 [10.218] / 5
17. Engine - Fuel injection system
Low pressure pump testing
BAIL08CVT130FSA 3
• (1) 380100057 0 – 11 bar (0 – 160 psi) gauge and hose assembly
• (2) Low Pressure Pump
• (3) 380100058 Plastic 2.0 l (4.2 US pt) container located not more than 1 m (3.3 ft)
48143358 20/04/2017
10.2 [10.218] / 6
18. Engine - Fuel injection system
5. If the pressure is still below 5 bar (73 psi) minimum,
perform tests in steps 6 and 7.
6. Supply fuel from an alternate fuel source (a separate
container, 380100058), located not more than 1 m
(3.3 ft) below the engine with a known good supply
line. This bypasses:
• The Fuel Tank, Inlet Lines and Connections, and
Pre-Filter (if equipped).
• Connect a pressure gauge assembly 380100057
between the fuel filter outlet and the high pressure
pump inlet.
7. The engine should start (at the first or second attempt)
and then draw fuel from the external container. Check
the fuel pressure at 1500 RPM. The reading on the fil-
ter outlet pressure gauge should be higher than 5 bar
(73 psi). If the pressure is lower than 5 bar (73 psi):
• Replace the fuel filter(s).
• Retest. If the pressure is still below 5 bar (73 psi),
replace the low pressure pump.
• Retest. If the pressure is still below 5 bar (73 psi),
the pressure regulator (part of the high pressure
pump assembly) could be responsible, replace the
high pressure pump.
Pressure relief valve testing
BAIL08CVT131FSA 4
• (1) Fuel rail
• (2) Pressure Relief Valve Return Line Coupler
48143358 20/04/2017
10.2 [10.218] / 7
19. Engine - Fuel injection system
8. The Pressure Relief Valve is located at rear end of the
fuel rail. This pressure relief valve protects the fuel
system components from excessive pressure if:
• The Rail Pressure Sensor fails to signal the correct
pressure to the ECU (Engine Control Unit).
• The High Pressure Flow Regulator, located at the
pump, allows excessive pressure in the high pres-
sure system.
Check the ECU for:
• Fault codes related to over pressurization of the
common rail, refer to: High Pressure Flow Regula-
tor.
9. Disconnect the pressure relief valve return line and cap
the line with 380100060 cap. Install 380100057 gauge
and hose assembly on the relief valve to direct any
leakage to container 380100062 if the relief valve is
leaking.
NOTE: Under normal circumstances fuel should not come
out of the relief valve.
10. If the diagnostic system does not indicate a fault code
and fuel is leaking from the pressure relief valve, re-
place the pressure relief valve.
High pressure flow regulator
BAIL08CVT132FSA 5
• (1) High Pressure Flow Regulator (Resistance Specification is 3.2 Ω )
48143358 20/04/2017
10.2 [10.218] / 8
20. Engine - Fuel injection system
11. The High Pressure Flow Regulator is an electrical con-
trol located at the inlet of the high pressure pump. It
regulates the amount of fuel supplied to the high pres-
sure system based on control signals received from
the ECU (by modulating the pulses sent to the internal
solenoid). This is used to control the pressure within
the fuel rail.
• The high pressure flow regulator is normally open.
• The high pressure pump is in maximum delivery
mode if no control signal is sent by the ECU.
12. If the high pressure flow regulator has an open circuit
(the flow regulator is disconnected, the harness is bro-
ken, etc.) or a short circuit (resistance value is much
lower than 3.2 Ω):
• The pump will be in maximum delivery mode
and pressure in the rail will exceed 1700 bar
(24650 psi) for a very short amount of time.
• The High pressure relief valve will open.
• The ECU sense the over pressure condition and
store fault codes in the ECU memory.
• The engine will derate.
13. Check the resistance (on the ECU connector pins).
The resistance specification is approximately 3.2 Ω.
14. When in parameter mode on the Electronic Service
Tool, the duty cycle reading indicates the position of
the regulator.
NOTICE: When all of the system components have been checked, inspect for the following symptoms:
The duty cycle tends to fluctuate irregularly and the engine idle speed is irregular.
• The engine stalls when idling and no fault is stored in the ECU.
• Starting is difficult (takes longer than 4 seconds).
Replace the high pressure flow regulator.
48143358 20/04/2017
10.2 [10.218] / 9
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Engine - Fuel injection system
Fuel injectors
BAIL08CVT133FSA 6
• (1) Return Line at Fuel Filter Base (disconnect and plug using 380100059)
• (2) Return Line Shown Disconnected and Capped ( 380100060)
• (3) Drain Line (use gauge and hose assembly 380100057 as the drain line) Shown connected to fuel return
outlet on the cylinder head
• (4) 100 ml (3.4 US fl oz) Cup (380100062)
15. Engine load and rpm are controlled by the fuel injec-
tors. The load requested by the operator is controlled
by the throttle position and converted into a fuel quan-
tity by the ECU. The ECU controls the amount and
timing of the fuel injection (using current fuel rail pres-
sure as a factor). Fuel injector mechanical problems:
• If the engine is difficult to start (excessive cranking
time and no fault codes present):
• Warm engine to 50 °C (122 °F) minimum. Check for
excessive fuel return of the cylinder head injectors
(with the engine running at low idle (no load - A/C
etc.). Complete (A) and/or (B) as required.
NOTE: Return leakage can be checked at various locations
(at the filter base or the cylinder head depending on ease
of the connection. If excessive leakage is found, additional
testing will be required to determine the exact location(s)
of the leakage. Each fuel injector connector and the pres-
sure relief valve could be a source of excessive return flow.
More than one component could be responsible for exces-
sive return.
48143358 20/04/2017
10.2 [10.218] / 10
23. Engine - Fuel injection system
(A) - Disconnect the return line at the fuel filter base
and plug (380100059) the filter port. Drain the fuel re-
turn line at the filter head into a 100 ml (3.4 US fl oz)
cup (380100062) and measure the amount of fuel that
escapes from the drain line in one minute. Leakage
should not exceed 80 ml (2.7 US fl oz) per minute with
the engine running at low idle. If leakage exceeds 80 ml
(2.7 US fl oz) retest as directed in Step (B) to determine
location of leakage.
(B) - Disconnect the return line on the engine cylinder
head and cap ( 380100060 ) the line. Connect a drain
line (use 380100057 as a drain line) to the fuel return
outlet on the cylinder head and measure the amount
of fuel that escapes from the cylinder head port in one
minute using a 100 ml (3.4 US fl oz) cup (380100062).
Leakage should not exceed 80 ml (2.7 US fl oz) per
minute with the engine running at low idle.
BAIL08CVT134FSA 7
• (1) Injector
• (2) Injector Connector - Check the fuel injector end of the connector to make sure is not deformed.
• (3) Injector Connector Cylinder Head Location - Torque Specification is 45 – 55 Nm (33 – 41 lb ft)
• (4) Fuel Rail Outlet - Cap ( 380100061) each fuel rail outlet location; one at a time.
• (5) Interface location between injector and injector connector
48143358 20/04/2017
10.2 [10.218] / 11
24. Engine - Fuel injection system
16. If leakage from the cylinder head port exceeds 80 ml
(2.7 US fl oz) per minute with the engine running at
low idle, check the leakage within each injector.
• Maintain engine temperature, 50 °C (122 °F)
minimum. To locate a damaged injector, cap (
380100061) each fuel rail outlet location; one at
a time. Recheck the total leakage. When the
return leakage value drops significantly with a fuel
rail outlet capped, a leaking injector has been
identified. Replace the damaged injector. Retest
total leakage to ensure additional injectors are not
leaking excessively.
• Inspect the injector connector between each fuel
injector and the associated fuel rail line. The torque
specification is for the injector connector is 45 –
55 Nm (33 – 41 lb ft). Check the fuel injector end of
the connector to make sure is not deformed. If the
injector end of the connector is deformed, replace
the injector connector.
• If the injector supply tube is not the cause of the
leakage, the injector may have internal leakage and
require replacement. Injectors could leak exces-
sively at operating temperature and perform cor-
rectly cold. Test kits 380040185 and 380040188
can be used to bench test injectors.
NOTE: Injectors and injector connectors are replaced as
pairs.
48143358 20/04/2017
10.2 [10.218] / 12