This service manual provides information for servicing the following models of Case IH tractors: PUMA® 185 CVT, PUMA® 185, PUMA® 200 CVT, PUMA® 200, PUMA® 220 CVT, PUMA® 220, and PUMA® 240 CVT. The manual covers maintenance and repair procedures for the engine, transmission, axles, hydraulics, electrical systems, and other components. Safety precautions and instructions are provided throughout for working on and handling parts of the tractor.
Case ih magnum 250 cvt tier 4 b tractor service repair manual [zhrf04001 ]ufjjskekfmmse
This service manual provides information for servicing the engines and components of several Magnum tractor models. It details removal and installation procedures for various engine systems like the cylinder heads, air cleaners, fuel filters, engine lubrication system, aftercooler, cooling system, and SCR exhaust treatment. In addition to the engine, it also covers servicing procedures for systems like the transmission, front and rear axles, PTO, brakes, hydraulics, steering, electrical components, and cab components. Removal and installation steps are provided along with notes on required prior operations.
Hyster g007 (h12.00 xm) forklift parts catalogue manualfusjejfjskekem
This parts manual is divided into 14 major sections covering the various systems of the Challenger H8.00-12.00XM truck. Section 1 covers the frame and includes descriptions and illustrations of components such as the hood, cab, counterweight, floor plates, and labels. Repair procedures can be found in the service manual.
Hyster d024 (s155 ft) forklift service repair manualfusjejfjskekem
This document provides instructions for repairing the hydraulic gear pump assembly for various lift truck models. It describes removing the pump from the transmission housing and draining hydraulic fluid from the tank. The pump is then disassembled by removing housings, seals, gears, and plates. Individual parts are cleaned, inspected for wear, and replaced as needed. Reassembly involves installing new seals and plates and reattaching the housings. Finally, the pump is reinstalled on the transmission housing with fittings attached to hydraulic lines.
Hyster c114 (e35 xl) forklift service repair manualfusjejfjskekem
This document provides descriptions and diagrams of steering systems for lift trucks, including power steering and power steering with on-demand systems. It describes the main components such as the steering wheel, encoder, actuator, control unit, pump motor, and hydraulic cylinders or motors. Power steering systems use a hydraulic circuit to route pressurized fluid from the pump motor to steering components when the wheel is turned, while on-demand systems only operate the pump motor during steering wheel movement. The control unit routes hydraulic fluid to steer the truck based on wheel position. Diagrams show hydraulic and electrical configurations.
Hyster a917 (h800 hds) forklift service repair manualfusjejfjskekem
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Safety precautions are provided and components are labeled in diagrams.
Cummins onan generator set with power command 3100 controller model (dfeb ) s...fusjejfjskekem
This document is a service manual that provides information for troubleshooting and servicing generator sets that use PowerCommand 3100 controllers. It contains sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and safety instructions for working on the generator set and power control systems.
Caterpillar cat 320 e excavator (prefix klt) service repair manual (klt00001 ...fusjejfjskekem
This service repair manual provides instructions for removing and installing various components of the heating and air conditioning system on a 320E and 320E L excavator. The components include the actuator motor, control module, refrigerant receiver-dryer, and various ducts, hoses, and panels. Detailed illustrations accompany the step-by-step removal and installation procedures, which note safety precautions like using protective equipment when working with refrigerant and not smoking in refrigerant areas.
Caterpillar cat 320 c excavator (prefix gla) service repair manual (gla00001 ...fusjejfjskekem
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and bearings from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, driver groups and presses. The component weights range from 29 kg for the ring gear to 190 kg for the assembled swing drive.
Case ih magnum 250 cvt tier 4 b tractor service repair manual [zhrf04001 ]ufjjskekfmmse
This service manual provides information for servicing the engines and components of several Magnum tractor models. It details removal and installation procedures for various engine systems like the cylinder heads, air cleaners, fuel filters, engine lubrication system, aftercooler, cooling system, and SCR exhaust treatment. In addition to the engine, it also covers servicing procedures for systems like the transmission, front and rear axles, PTO, brakes, hydraulics, steering, electrical components, and cab components. Removal and installation steps are provided along with notes on required prior operations.
Hyster g007 (h12.00 xm) forklift parts catalogue manualfusjejfjskekem
This parts manual is divided into 14 major sections covering the various systems of the Challenger H8.00-12.00XM truck. Section 1 covers the frame and includes descriptions and illustrations of components such as the hood, cab, counterweight, floor plates, and labels. Repair procedures can be found in the service manual.
Hyster d024 (s155 ft) forklift service repair manualfusjejfjskekem
This document provides instructions for repairing the hydraulic gear pump assembly for various lift truck models. It describes removing the pump from the transmission housing and draining hydraulic fluid from the tank. The pump is then disassembled by removing housings, seals, gears, and plates. Individual parts are cleaned, inspected for wear, and replaced as needed. Reassembly involves installing new seals and plates and reattaching the housings. Finally, the pump is reinstalled on the transmission housing with fittings attached to hydraulic lines.
Hyster c114 (e35 xl) forklift service repair manualfusjejfjskekem
This document provides descriptions and diagrams of steering systems for lift trucks, including power steering and power steering with on-demand systems. It describes the main components such as the steering wheel, encoder, actuator, control unit, pump motor, and hydraulic cylinders or motors. Power steering systems use a hydraulic circuit to route pressurized fluid from the pump motor to steering components when the wheel is turned, while on-demand systems only operate the pump motor during steering wheel movement. The control unit routes hydraulic fluid to steer the truck based on wheel position. Diagrams show hydraulic and electrical configurations.
Hyster a917 (h800 hds) forklift service repair manualfusjejfjskekem
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Safety precautions are provided and components are labeled in diagrams.
Cummins onan generator set with power command 3100 controller model (dfeb ) s...fusjejfjskekem
This document is a service manual that provides information for troubleshooting and servicing generator sets that use PowerCommand 3100 controllers. It contains sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and safety instructions for working on the generator set and power control systems.
Caterpillar cat 320 e excavator (prefix klt) service repair manual (klt00001 ...fusjejfjskekem
This service repair manual provides instructions for removing and installing various components of the heating and air conditioning system on a 320E and 320E L excavator. The components include the actuator motor, control module, refrigerant receiver-dryer, and various ducts, hoses, and panels. Detailed illustrations accompany the step-by-step removal and installation procedures, which note safety precautions like using protective equipment when working with refrigerant and not smoking in refrigerant areas.
Caterpillar cat 320 c excavator (prefix gla) service repair manual (gla00001 ...fusjejfjskekem
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and bearings from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, driver groups and presses. The component weights range from 29 kg for the ring gear to 190 kg for the assembled swing drive.
Caterpillar cat 320 c excavator (prefix bea) service repair manual (bea00001 ...fusjejfjskekem
This document provides instructions for removing a bucket cylinder from an excavator. It begins by noting the importance of relieving pressure from hydraulic systems before disassembly to prevent injury. The steps include releasing hydraulic pressure, attaching lifting devices, removing retaining bolts and pins, and disconnecting hoses. Identification marks should be made on all lines and components. Cleanliness is important during disassembly and reassembly to prevent contamination of hydraulic systems.
This document provides instructions for installing an automatic timing advance on a 3306 engine. It involves using various tools to install a fuel pump timing pin and bolt to hold the automatic timing advance in place while tightening another bolt. The timing advance is then tightened to a specified torque and the tools are removed. Finally, the front housing is reinstalled.
This document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar 235 excavator engine. It describes using various tools to distort the wear sleeve and remove the old seal. When installing the new seal and sleeve, no lubricant should be used and retaining compound is applied to mate the surfaces. The flywheel housing is removed using link brackets and bolts, and installed by reversing the process.
Caterpillar cat 232 d skid steer loader (prefix kxc) service repair manual (k...fusjejfjskekem
1. The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C2.2 engine.
2. To remove the flywheel, mounting bolts must be removed and lifting tools installed to lift the heavy flywheel off of alignment dowels.
3. Flywheel installation requires cleaning surfaces, heating the ring gear for installation, aligning the flywheel on dowels, and torquing mounting bolts to the specified value.
4. Crankshaft rear seal removal requires removing the flywheel housing or back plate and pulling the old seal. Installation requires cleaning, applying sealant, pressing the new seal in place, and replacing the
The document provides instructions for removing and installing fuel system components on a Caterpillar 229 Excavator including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump and disassembling/assembling it.
- Installing the fuel transfer pump.
The instructions include safety notices and illustrations showing the component locations and part numbers. Procedures note removing bolts and hoses, checking gaskets, and reinstalling components in the reverse order of removal.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure and containing fluids during disassembly.
New holland w70 c tier 4b (final) compact wheel loader service repair manualfusjejfjskekem
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and radiator grids.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser (if equipped).
3. Put battery main switch in OFF position. Secure engine hood with lifting strap before removing hood hinge bolts.
New holland w70 c tier 4 compact wheel loader service repair manualfusjejfjskekem
This document is a service manual for compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, electrical systems, and cab. The manual provides instructions for maintenance and repair work to be performed by qualified dealership personnel using the specified tools and procedures.
This document provides instructions for assembling and disassembling components of the governor assembly and fuel injection pump on a 3034 engine for Caterpillar built machines. It describes how to assemble the governor control lever and fuel control lever, install the governor weight assembly and speed control lever. It also provides instructions for removing and installing the fuel injection pump, including cleaning surfaces, installing shims and dowels, and connecting linkages and springs.
Caterpillar cat 226 d skid steer loader (prefix hrd) service repair manual (h...fusjejfjskekem
This document provides instructions for removing and installing fuel injection lines and an exhaust cooler on a Caterpillar C2.2 engine. The summary is:
1) The document outlines the required tools and safety precautions for working on the fuel system and with sulfuric acid.
2) The procedure for removing the fuel injection lines includes disconnecting clamps and nuts, removing the lines, and installing capping kits on the injectors and manifold.
3) Installation involves reconnecting the lines with new isolators and gaskets, tightening all nuts and bolts to the specified torques, and priming the fuel system.
4) Removal of the exhaust cooler involves disconnecting hoses
New holland w60 tc wheel loader service repair manualfusjejfjskekem
This document provides repair manuals and technical specifications for W50TC, W60TC, W70TC, and W80TC wheel loaders. It includes sections on the engine, front and rear axles, braking system, hydraulic system, and their various components. Diagrams, dimensions, troubleshooting guides, and disassembly/reassembly instructions are provided to assist with maintenance and repairs.
New holland w60 c zb stage iiib compact wheel loader service repair manualfusjejfjskekem
This document provides instructions for removing an engine from a compact wheel loader. It begins with parking the machine securely and stopping the engine. The instructions then describe aligning mounting bores and securing the engine with a pin located on the machine frame.
New holland w50 wheel loader service repair manualfusjejfjskekem
The document is a workshop manual for wheel loaders that provides safety instructions for personnel. It contains sections on fundamental safety, operation safety, maintenance safety, repairs safety, and safety warnings. Personnel are instructed to carefully read all safety instructions, wear protective equipment, ensure only authorized trained staff perform repairs, and more. The workshop manual aims to protect operator safety and prevent accidents during operation and maintenance of the wheel loaders.
Case ih stx 280 tractor service repair manualfusjejfjskekem
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair, removal and installation procedures for various components. Key sections include engine repair information, lubrication requirements, air induction systems, electrical systems, steering components, and center consoles. The document directs the user to additional manuals for more detailed information on specific topics and components.
New holland u80 loader landscaper service repair manualfusjejfjskekem
This document is the service manual for a CNH America LLC U80 Loader Landscaper. It contains:
- Copyright information and publication details
- A table of contents listing the manual sections and corresponding page numbers
- Section indexes providing the titles and page numbers for sections related to general information, engine, fuel system, electrical systems, steering, power train, brakes, hydraulics, and mounted equipment
- Specification details and torque charts for engine components, fluids, and hydraulic fittings
The manual provides maintenance technicians with information on removal, installation, specifications, troubleshooting and pressure checks for the loader's various systems and components. Tables of contents and section indexes help technicians quickly navigate to relevant information.
New holland tc5080 combine harvesters service repair manualfusjejfjskekem
The air compressor supplies compressed air to the reservoir tank to provide a source of compressed air for cleaning and tire inflation. It is a single cylinder, gear-driven compressor mounted directly to the engine. Engine oil lubricates the compressor. The compressed air relief valve protects the system from pressures over 116 psi by venting excess pressure. It can be removed by draining the air and coolant lines, loosening connections, and removing mounting bolts and nuts.
Case 1650 l crawler dozer service repair manualfusjejfjskekem
The document provides instructions to remove and disassemble the engine from a machine. The key steps include draining fluids, disconnecting wiring and hoses, removing mounting hardware, and using lifting equipment to remove the engine. Once removed, further disassembly instructions are provided to prepare the engine for repair on a workbench, including draining oil and removing fuel system components.
New holland tc5070 hillside combine harvesters service repair manualfusjejfjskekem
The primary hydraulic power system for the TC5000 series combines includes two pumps without lateral flotation and three pumps with lateral flotation. Key components are the main hydraulic pump, steering pump, optional lateral flotation pump, oil tank, filters, valve stack with various control valves, header lift cylinders, accumulator and pressure sensor, steering cylinder(s), optional lateral float cylinder, and rotary union.
New holland tc5070 combine harvesters service repair manualfusjejfjskekem
This service manual provides information on servicing various components of TC5040, TC5050, TC5060, TC5070, TC5070, TC5080 Hillside, and TC5080 combines. The manual covers engines, transmissions, brakes, hydraulics, electrical systems, attachments, feeding, threshing, separation, cleaning, and other systems. Repair and maintenance must only be done by trained technicians using the proper tools and procedures. Unauthorized repairs may void warranties.
New holland tc45 a tractor service repair manualfusjejfjskekem
This document is the contents page for a repair manual for New Holland TC35A, TC35DA, TC40A, TC40DA, TC45A, and TC45DA tractors. It lists the sections and chapters contained within the repair manual, including the engine, clutch, transmission, driveline, front and rear axles, brakes, hydraulic system, steering, climate control, electrical systems, and platform. The document provides an overview of the complete contents and organization of the repair manual.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Caterpillar cat 320 c excavator (prefix bea) service repair manual (bea00001 ...fusjejfjskekem
This document provides instructions for removing a bucket cylinder from an excavator. It begins by noting the importance of relieving pressure from hydraulic systems before disassembly to prevent injury. The steps include releasing hydraulic pressure, attaching lifting devices, removing retaining bolts and pins, and disconnecting hoses. Identification marks should be made on all lines and components. Cleanliness is important during disassembly and reassembly to prevent contamination of hydraulic systems.
This document provides instructions for installing an automatic timing advance on a 3306 engine. It involves using various tools to install a fuel pump timing pin and bolt to hold the automatic timing advance in place while tightening another bolt. The timing advance is then tightened to a specified torque and the tools are removed. Finally, the front housing is reinstalled.
This document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar 235 excavator engine. It describes using various tools to distort the wear sleeve and remove the old seal. When installing the new seal and sleeve, no lubricant should be used and retaining compound is applied to mate the surfaces. The flywheel housing is removed using link brackets and bolts, and installed by reversing the process.
Caterpillar cat 232 d skid steer loader (prefix kxc) service repair manual (k...fusjejfjskekem
1. The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C2.2 engine.
2. To remove the flywheel, mounting bolts must be removed and lifting tools installed to lift the heavy flywheel off of alignment dowels.
3. Flywheel installation requires cleaning surfaces, heating the ring gear for installation, aligning the flywheel on dowels, and torquing mounting bolts to the specified value.
4. Crankshaft rear seal removal requires removing the flywheel housing or back plate and pulling the old seal. Installation requires cleaning, applying sealant, pressing the new seal in place, and replacing the
The document provides instructions for removing and installing fuel system components on a Caterpillar 229 Excavator including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump and disassembling/assembling it.
- Installing the fuel transfer pump.
The instructions include safety notices and illustrations showing the component locations and part numbers. Procedures note removing bolts and hoses, checking gaskets, and reinstalling components in the reverse order of removal.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure and containing fluids during disassembly.
New holland w70 c tier 4b (final) compact wheel loader service repair manualfusjejfjskekem
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and radiator grids.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser (if equipped).
3. Put battery main switch in OFF position. Secure engine hood with lifting strap before removing hood hinge bolts.
New holland w70 c tier 4 compact wheel loader service repair manualfusjejfjskekem
This document is a service manual for compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, electrical systems, and cab. The manual provides instructions for maintenance and repair work to be performed by qualified dealership personnel using the specified tools and procedures.
This document provides instructions for assembling and disassembling components of the governor assembly and fuel injection pump on a 3034 engine for Caterpillar built machines. It describes how to assemble the governor control lever and fuel control lever, install the governor weight assembly and speed control lever. It also provides instructions for removing and installing the fuel injection pump, including cleaning surfaces, installing shims and dowels, and connecting linkages and springs.
Caterpillar cat 226 d skid steer loader (prefix hrd) service repair manual (h...fusjejfjskekem
This document provides instructions for removing and installing fuel injection lines and an exhaust cooler on a Caterpillar C2.2 engine. The summary is:
1) The document outlines the required tools and safety precautions for working on the fuel system and with sulfuric acid.
2) The procedure for removing the fuel injection lines includes disconnecting clamps and nuts, removing the lines, and installing capping kits on the injectors and manifold.
3) Installation involves reconnecting the lines with new isolators and gaskets, tightening all nuts and bolts to the specified torques, and priming the fuel system.
4) Removal of the exhaust cooler involves disconnecting hoses
New holland w60 tc wheel loader service repair manualfusjejfjskekem
This document provides repair manuals and technical specifications for W50TC, W60TC, W70TC, and W80TC wheel loaders. It includes sections on the engine, front and rear axles, braking system, hydraulic system, and their various components. Diagrams, dimensions, troubleshooting guides, and disassembly/reassembly instructions are provided to assist with maintenance and repairs.
New holland w60 c zb stage iiib compact wheel loader service repair manualfusjejfjskekem
This document provides instructions for removing an engine from a compact wheel loader. It begins with parking the machine securely and stopping the engine. The instructions then describe aligning mounting bores and securing the engine with a pin located on the machine frame.
New holland w50 wheel loader service repair manualfusjejfjskekem
The document is a workshop manual for wheel loaders that provides safety instructions for personnel. It contains sections on fundamental safety, operation safety, maintenance safety, repairs safety, and safety warnings. Personnel are instructed to carefully read all safety instructions, wear protective equipment, ensure only authorized trained staff perform repairs, and more. The workshop manual aims to protect operator safety and prevent accidents during operation and maintenance of the wheel loaders.
Case ih stx 280 tractor service repair manualfusjejfjskekem
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair, removal and installation procedures for various components. Key sections include engine repair information, lubrication requirements, air induction systems, electrical systems, steering components, and center consoles. The document directs the user to additional manuals for more detailed information on specific topics and components.
New holland u80 loader landscaper service repair manualfusjejfjskekem
This document is the service manual for a CNH America LLC U80 Loader Landscaper. It contains:
- Copyright information and publication details
- A table of contents listing the manual sections and corresponding page numbers
- Section indexes providing the titles and page numbers for sections related to general information, engine, fuel system, electrical systems, steering, power train, brakes, hydraulics, and mounted equipment
- Specification details and torque charts for engine components, fluids, and hydraulic fittings
The manual provides maintenance technicians with information on removal, installation, specifications, troubleshooting and pressure checks for the loader's various systems and components. Tables of contents and section indexes help technicians quickly navigate to relevant information.
New holland tc5080 combine harvesters service repair manualfusjejfjskekem
The air compressor supplies compressed air to the reservoir tank to provide a source of compressed air for cleaning and tire inflation. It is a single cylinder, gear-driven compressor mounted directly to the engine. Engine oil lubricates the compressor. The compressed air relief valve protects the system from pressures over 116 psi by venting excess pressure. It can be removed by draining the air and coolant lines, loosening connections, and removing mounting bolts and nuts.
Case 1650 l crawler dozer service repair manualfusjejfjskekem
The document provides instructions to remove and disassemble the engine from a machine. The key steps include draining fluids, disconnecting wiring and hoses, removing mounting hardware, and using lifting equipment to remove the engine. Once removed, further disassembly instructions are provided to prepare the engine for repair on a workbench, including draining oil and removing fuel system components.
New holland tc5070 hillside combine harvesters service repair manualfusjejfjskekem
The primary hydraulic power system for the TC5000 series combines includes two pumps without lateral flotation and three pumps with lateral flotation. Key components are the main hydraulic pump, steering pump, optional lateral flotation pump, oil tank, filters, valve stack with various control valves, header lift cylinders, accumulator and pressure sensor, steering cylinder(s), optional lateral float cylinder, and rotary union.
New holland tc5070 combine harvesters service repair manualfusjejfjskekem
This service manual provides information on servicing various components of TC5040, TC5050, TC5060, TC5070, TC5070, TC5080 Hillside, and TC5080 combines. The manual covers engines, transmissions, brakes, hydraulics, electrical systems, attachments, feeding, threshing, separation, cleaning, and other systems. Repair and maintenance must only be done by trained technicians using the proper tools and procedures. Unauthorized repairs may void warranties.
New holland tc45 a tractor service repair manualfusjejfjskekem
This document is the contents page for a repair manual for New Holland TC35A, TC35DA, TC40A, TC40DA, TC45A, and TC45DA tractors. It lists the sections and chapters contained within the repair manual, including the engine, clutch, transmission, driveline, front and rear axles, brakes, hydraulic system, steering, climate control, electrical systems, and platform. The document provides an overview of the complete contents and organization of the repair manual.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
3. Link Product / Engine
Product Market Product Engine
PUMA® 185 CVT North America F4DFE613K*B006
PUMA® 200 CVT North America F4DFE613J*B006
PUMA® 220 CVT North America F4DFE613H*B003
PUMA® 240 CVT North America F4DFE613B*B006
PUMA® 185 North America F4DFE613K*B006
PUMA® 200 North America F4DFE613J*B006
PUMA® 220 North America F4DFE613H*B003
47936452 17/11/2015
10. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47936452 17/11/2015
3
11. INTRODUCTION
Safety rules - Ecology and the environment
Soil, air, and water quality is important for all industries and life in general. When legislation does not yet rule the
treatment of some of the substances that advanced technology requires, sound judgment should govern the use and
disposal of products of a chemical and petrochemical nature.
Familiarize yourself with the relative legislation applicable to your country, and make sure that you understand this
legislation. Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, anti-freeze,
cleaning agents, etc., with regard to the effect of these substances on man and nature and how to safely store, use,
and dispose of these substances.
Helpful hints
• Avoid the use of cans or other inappropriate pressurized fuel delivery systems to fill tanks. Such delivery systems
may cause considerable spillage.
• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of these products contain substances
that may be harmful to your health.
• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
• Avoid spillage when you drain fluids such as used engine coolant mixtures, engine oil, hydraulic fluid, brake fluid,
etc. Do not mix drained brake fluids or fuels with lubricants. Store all drained fluids safely until you can dispose of
the fluids in a proper way that complies with all local legislation and available resources.
• Do not allow coolant mixtures to get into the soil. Collect and dispose of coolant mixtures properly.
• The air-conditioning system contains gases that should not be released into the atmosphere. Consult an air-condi-
tioning specialist or use a special extractor to recharge the system properly.
• Repair any leaks or defects in the engine cooling system or hydraulic system immediately.
• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
• Protect hoses during welding. Penetrating weld splatter may burn a hole or weaken hoses, allowing the loss of oils,
coolant, etc.
Battery recycling
Batteries and electric accumulators contain several substances that can have a harmful
effect on the environment if the batteries are not properly recycled after use. Improper
disposal of batteries can contaminate the soil, groundwater, and waterways. CASE IH
strongly recommends that you return all used batteries to a CASE IH dealer, who will
dispose of the used batteries or recycle the used batteries properly. In some countries,
this is a legal requirement.
Mandatory battery recycling
NOTE: The following requirements are mandatory in Brazil.
Batteries are made of lead plates and a sulfuric acid solution. Because batteries contain heavy metals such as lead,
CONAMA Resolution 401/2008 requires you to return all used batteries to the battery dealer when you replace any
batteries. Do not dispose of batteries in your household garbage.
Points of sale are obliged to:
• Accept the return of your used batteries
• Store the returned batteries in a suitable location
• Send the returned batteries to the battery manufacturer for recycling
47936452 17/11/2015
4
13. Engine - Engine and crankcase
Engine - Remove
Prior operation:
Separate the front axle and front frame from the engine, for further information refer to Front frame - Remove (39.100)
Prior operation:
Remove the left-hand fuel tank, for further information refer to Fuel tank - Remove (10.216)
Prior operation:
Remove the selective catalytic reduction (SRC) muffler, for further information refer to Selective Catalytic Reduction
(SCR) muffler and catalyst - Remove (10.500)
Prior operation:
Remove the engine hood, for further information refer to Hood - Remove (90.100)
WARNING
Heavy objects!
Lift and handle all heavy components using lift-
ing equipment with adequate capacity. Always
support units or parts with suitable slings or
hooks. Make sure the work area is clear of all
bystanders.
Failure to comply could result in death or seri-
ous injury.
W0398A
WARNING
Avoid injury!
Handle all parts carefully. Do not place your
hands or fingers between parts. Use Personal
Protective Equipment (PPE) as indicated in this
manual, including protective goggles, gloves,
and safety footwear.
Failure to comply could result in death or seri-
ous injury.
W0208A
NOTICE: Avoid DEF/ADBLUE® contamination of the electrical connector by disconnecting the DEF/ADBLUE® con-
nectors first.
1. 1. Disconnect the radar electrical connector (if fitted).
2. Remove the radar (if fitted).
BAIL13TR01648AB 1
47936452 17/11/2015
10.1 [10.001] / 3
14. Engine - Engine and crankcase
Vehicles with front hitch
2. Disconnect the mid-mount pipes from the mid-mount
valve.
BAIL13TR01645AB 2
3. Remove the front hitch pipes.
BAIL13TR01647AB 3
4. Remove the starter motor cover.
BAIL14TR00276AB 4
5. Remove the oil cooler pipe bracket.
BAIL14TR00277AB 5
47936452 17/11/2015
10.1 [10.001] / 4
15. Engine - Engine and crankcase
6. Detach the fuse box and position it to one side.
BAIL13TR01663AB 6
7. Disconnect the starter motor positive cables.
BAIL14TR00278AA 7
8. Disconnect the starter motor electrical connector.
BAIL13TR01660AB 8
9. Disconnect the starter motor negative terminal.
BAIL13TR01661AB 9
47936452 17/11/2015
10.1 [10.001] / 5
16. Engine - Engine and crankcase
10. Disconnect the front axle electrical connectors.
BAIL13TR01683AB 10
11. Disconnect the brake master cylinder oil supply pipes.
BAIL14TR00279AB 11
12. Disconnect the cab hand rail light electrical connec-
tors (on both sides).
BAIL14TR00280AB 12
13. 1. Disconnect the steering pipes.
2. Disconnect the brake pipe.
NOTE: Mark the hoses to aid installation.
BAIL14TR00281AB 13
47936452 17/11/2015
10.1 [10.001] / 6
17. Engine - Engine and crankcase
14. Disconnect the ground cables.
BAIL14TR00282AB 14
15. Disconnect the generator electrical connectors.
BAIL14TR00283AB 15
16. 1. Disconnect the brake accumulator electrical con-
nector.
2. Disconnect the water-in-fuel sensor electrical
connector.
BAIL14TR00284AB 16
17. 1. Disconnect the flywheel speed sensor electrical
connector.
2. Disconnect the engine wiring harness.
BAIL14TR00285AB 17
47936452 17/11/2015
10.1 [10.001] / 7
18. Engine - Engine and crankcase
18. Disconnect the air conditioning (A/C) pipes.
NOTE: Make sure that all openings are sealed. Use new
blanking caps.
BAIL14TR00286AB 18
19. 1. Disconnect the coolant hose.
2. Disconnect the brake pipe.
BAIL14TR00287AB 19
20. Cut the cable ties.
BAIL14TR00288AB 20
21. 1. Disconnect the Diesel Oxidation Catalyst (DOC)
electrical connector.
2. Disconnect the hood wiring harness electrical
connector.
BAIL14TR00289AB 21
47936452 17/11/2015
10.1 [10.001] / 8
19. Engine - Engine and crankcase
22. Cut the cable ties.
BAIL14TR00290AB 22
23. 1. Detach the DOC wiring harness and the DEF/
ADBLUE® lines.
2. Detach the wiring harness.
BAIL14TR00291AB 23
24. Disconnect the dosing module.
1. Disconnect the DEF/ADBLUE® lines.
2. Disconnect the dosing module electrical connec-
tor.
BAIL14TR00292AB 24
25. 1. Detach the wiring harness.
2. Cut the cable ties.
BAIL14TR00293AB 25
47936452 17/11/2015
10.1 [10.001] / 9
20. Engine - Engine and crankcase
26. Cut the cable ties.
BAIL14TR00294AB 26
27. 1. Disconnect the fan electrical connector.
2. Disconnect front hitch electrical connector.
BAIL14TR00295AB 27
28. 1. Disconnect the NOx amplifier electrical connec-
tor.
2. Disconnect the coolant level sensor electrical
connector.
BAIL14TR00296AB 28
29. 1. Disconnect the AC pressure switch electrical con-
nector..
2. Cut the cable tie.
BAIL14TR00297AB 29
47936452 17/11/2015
10.1 [10.001] / 10
21. Engine - Engine and crankcase
30. 1. Disconnect the air intake sensor electrical con-
nector.
2. Disconnect the A/C compressor electrical con-
nector.
BAIL14TR00316AB 30
31. Remove the right-hand air intake pipe.
BAIL14TR00317AB 31
32. Remove the left-hand air intake pipe.
BAIL14TR00318AB 32
33. 1. Disconnect the air compressor supply pipe.
2. Disconnect the valve cover breather pipe.
BAIL14TR00319AB 33
47936452 17/11/2015
10.1 [10.001] / 11
22. Engine - Engine and crankcase
34. Remove the air cleaner outlet pipe.
BAIL14TR00320AB 34
35. 1. Disconnect the coolant hose from the exhaust
flap.
2. Disconnect the coolant expansion tank hose.
3. Remove the up-stream Nox sensor.
BAIL14TR00321AB 35
36. Disconnect the engine frame upper retaining bolts.
BAIL14TR00323AB 36
37. 1. Remove the engine frame front retaining nuts.
2. Remove the upper part of the engine frame.
BAIL14TR00324AB 37
47936452 17/11/2015
10.1 [10.001] / 12
23. Engine - Engine and crankcase
38. 1. Disconnect the coolant lines from the exhaust
flap.
2. Disconnect the exhaust flap electrical connector.
BAIL14TR00325AB 38
39. Remove the DOC frame rear retaining bolts.
BAIL14TR00326AB 39
40. Remove the exhaust flap and exhaust front pipe.
BAIL14TR00327AB 40
41. Remove the DOC and frame.
BAIL14TR00328AB 41
47936452 17/11/2015
10.1 [10.001] / 13
24. Engine - Engine and crankcase
42. Remove the lower part of the engine frame.
BAIL14TR00329AB 42
43. Remove the engine side cover bracket.
BAIL14TR00330AB 43
44. Remove the rear part of the engine frame.
BAIL14TR00331AB 44
45. Remove the A/C pipes.
NOTE: Install blanking plugs.
BAIL14TR00332AB 45
47936452 17/11/2015
10.1 [10.001] / 14
25. Engine - Engine and crankcase
46. Remove the air compressor intake pipe.
BAIL14TR00333AB 46
47. Remove the engine frame front retaining bolts.
BAIL14TR00334AB 47
48. Position the static part of the tractor splitting stand
380003352 under the transmission and secure to the
transmission.
BAIL13TR01728AB 48
49. Install three engine lifting eyes 380200013.
BAIL14TR00335AB 49
47936452 17/11/2015
10.1 [10.001] / 15
26. Engine - Engine and crankcase
50. Using suitable lighting equipment, support the engine.
BAIL14TR00336AB 50
51. Remove the engine to transmission lower retaining
bolts.
BAIL13TR01727AB 51
52. Remove the engine to transmission upper retaining
bolts.
BAIL13TR01757AB 52
53. Remove the engine to transmission left-hand side re-
taining bolts.
BAIL13TR00796AB 53
47936452 17/11/2015
10.1 [10.001] / 16
27. Engine - Engine and crankcase
54. Remove the engine to transmission right-hand side
retaining bolts.
BAIL13TR00797AC 54
55. Using suitable lighting equipment, remove the engine.
BAIL14TR00337AA 55
47936452 17/11/2015
10.1 [10.001] / 17
28. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
29. Engine - Engine and crankcase
Engine - Disconnect
Prior operation:
Discharge the Air conditioning system, for further information refer to Air conditioning - Discharging (50.200)
Prior operation:
Drain the engine cooling system, for further information refer to Engine cooling system - Drain fluid (10.400)
Prior operation:
Disconnect the battery ground cable, for further information refer to Battery - Disconnect (55.302)
Prior operation:
Remove the Selective Catalytic Reduction (SCR) muffler, for further information refer to Selective Catalytic Reduc-
tion (SCR) muffler and catalyst - Remove (10.500)
Prior operation:
Remove the left-hand fuel tank, for further information refer to Fuel tank - Remove (10.216)
WARNING
Heavy objects!
Lift and handle all heavy components using lift-
ing equipment with adequate capacity. Always
support units or parts with suitable slings or
hooks. Make sure the work area is clear of all
bystanders.
Failure to comply could result in death or seri-
ous injury.
W0398A
WARNING
Avoid injury!
Handle all parts carefully. Do not place your
hands or fingers between parts. Use Personal
Protective Equipment (PPE) as indicated in this
manual, including protective goggles, gloves,
and safety footwear.
Failure to comply could result in death or seri-
ous injury.
W0208A
NOTICE: Avoid DEF/ADBLUE® contamination of the electrical connector by connecting the DEF/ADBLUE® connec-
tors last.
1. WARNING
Crushing hazard!
The wheels on this vehicle are very heavy. Al-
ways use a wheel remover or chain hoists to re-
move and install the wheels. Use an assistant
as required.
Failure to comply could result in death or seri-
ous injury.
W0149A
Install the left-hand rear wheel.
BAIL10CVT461AVA 1
47936452 17/11/2015
10.1 [10.001] / 18
30. Engine - Engine and crankcase
2. A. Remove the transmission housing drain plug and
drain the transmission oil into a suitable container.
B. Install the drain plug and torque to 68 - 82 N·m (50
- 60 lb ft)
BAIL07APH288AVA 2
3. 1. Disconnect the radar electrical connector and re-
move radar (if fitted).
2. Remove the radar (if fitted).
BAIL13TR01648AB 3
Vehicles with front hitch
4. WARNING
Heavy object!
ALWAYS use a hoist or get assistance to lift the
component.
Failure to comply could result in death or seri-
ous injury.
W0086A
Remove the right-hand side rail.
NOTE: Repeat this step for the left-hand side.
BAIL13TR01649AB 4
5. Disconnect the oil cooler supply and return pipes.
BAIL13TR01656AB 5
47936452 17/11/2015
10.1 [10.001] / 19
31. Engine - Engine and crankcase
6. Detach the cab heater supply pipe.
BAIL13TR01657AB 6
7. Remove the starter motor cover.
BAIL14TR00276AB 7
8. Remove the oil cooler pipe bracket.
BAIL14TR00277AB 8
9. Detach the fuse box and position it to one side.
BAIL13TR01663AB 9
47936452 17/11/2015
10.1 [10.001] / 20
32. Engine - Engine and crankcase
10. Disconnect the starter motor positive cables.
BAIL14TR00278AA 10
11. Disconnect the starter motor electrical connector.
BAIL13TR01660AB 11
12. Disconnect the starter motor negative terminal.
BAIL13TR01661AB 12
13. Disconnect the front axle electrical connectors.
BAIL13TR01683AB 13
47936452 17/11/2015
10.1 [10.001] / 21
33. Engine - Engine and crankcase
14. Disconnect the master cylinder oil supply pipes.
BAIL14TR00279AB 14
15. Disconnect the cab hand rail light electrical connec-
tors (on both sides).
BAIL14TR00280AB 15
16. 1. Disconnect the steering pipes.
2. Disconnect the brake pipe.
NOTE: Mark the hoses to aid installation.
BAIL14TR00281AB 16
17. Disconnect the earth cables.
BAIL14TR00282AB 17
47936452 17/11/2015
10.1 [10.001] / 22
34. Engine - Engine and crankcase
18. Disconnect the generator electrical connectors.
BAIL14TR00283AB 18
19. 1. Disconnect the brake accumulator electrical con-
nector.
2. Disconnect the water-in-fuel electrical connector.
BAIL14TR00284AB 19
20. 1. Disconnect the flywheel speed sensor.
2. Disconnect the engine wiring harness.
BAIL14TR00285AB 20
21. Disconnect the air conditioning (A/C) pipes.
BAIL14TR00286AB 21
47936452 17/11/2015
10.1 [10.001] / 23