The air compressor supplies compressed air to the reservoir tank to provide a source of compressed air for cleaning and tire inflation. It is a single cylinder, gear-driven compressor mounted directly to the engine. Engine oil lubricates the compressor. The compressed air relief valve protects the system from pressures over 116 psi by venting excess pressure. It can be removed by draining the air and coolant lines, loosening connections, and removing mounting bolts and nuts.
New holland t7.175 auto command stage iv tractor service repair manualfujdjjskekwmem
This document is a service manual that provides information on servicing various components of tractor models T7.175 AutoCommandTM, T7.175, T7.190 AutoCommandTM, T7.190, T7.210 AutoCommandTM, T7.210, and T7.225 AutoCommandTM. The manual contains sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes, hydraulic systems, pneumatic system, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork and decals. Each section provides removal and installation instructions, specifications
This document is a service manual for a 1150L Crawler Dozer made in Brazil with a Tier 3 engine. The manual contains over 20 sections covering various systems of the dozer like the engine, transmission, brakes, hydraulics, tracks, electrical systems, and more. Each section includes subsections for components, with technical specifications, operational descriptions, troubleshooting information, and service procedures.
New holland tc5.30 combine harvesters service repair manual instant downloadufjjsjekksekmm
This document is a service manual for the TC5.30 combine with and without cab. It contains sections covering the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, crop storage and unloading, platform, cab, bodywork, and decals. The introduction provides a foreword and notes the technical information is written to support maintenance and servicing of the machine's functions and systems.
New holland tc5.30 combine harvesters service repair manualujfdjjskkemme
The document is a service manual that provides technical information for servicing a TC5.30 combine. It contains sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section contains chapters that provide technical data, functional data, diagnostic data, and service procedures for the components in that section of the combine.
Case 1650 l crawler dozer service repair manualujdjkkskmme
This service manual provides information on servicing and repair for a 1650L XLT PAT excavator. It includes sections covering the engine, rear axle system, hydrostatic drive, brakes and controls, hydraulic systems, tracks and track suspension, cab climate control, electrical systems, dozer blade and arm, tools, and platform, cab, bodywork, and decals. The manual provides specifications, diagrams, removal and installation instructions, and troubleshooting information to guide maintenance and repairs.
Case 1150 l crawler dozer service repair manualujjdfjkskdme
This service manual provides information on servicing and repairing various components of an 1150L XLT PAT machine, including the engine, rear axle system, hydrostatic drive, brakes and controls, hydraulic systems, tracks and track suspension, cab climate control, electrical systems, dozer blade and arm, tools, and platform, cab, bodywork, and decals. The manual is divided into sections covering each major component or system, and each section contains chapters on specific subcomponents or aspects of that system. Technical specifications, diagrams, removal and installation instructions, and troubleshooting information are provided.
New holland 7030 l grape harvester service repair manualufjsjjkksemme
This service manual section provides information on the engine and crankcase for the 7030L grape harvester. It includes an overview of key engine components such as the cooling system, exhaust treatment system, air cleaner, and pumps. It also provides details on servicing items like checking the engine oil level, replacing filters, and adjusting valve clearances. Maintenance procedures and specifications are included to support servicing of the engine and associated systems.
Hyster g007 (h12.00 xm) forklift parts catalogue manualfusjejfjskekem
This parts manual is divided into 14 major sections covering the various systems of the Challenger H8.00-12.00XM truck. Section 1 covers the frame and includes descriptions and illustrations of components such as the hood, cab, counterweight, floor plates, and labels. Repair procedures can be found in the service manual.
New holland t7.175 auto command stage iv tractor service repair manualfujdjjskekwmem
This document is a service manual that provides information on servicing various components of tractor models T7.175 AutoCommandTM, T7.175, T7.190 AutoCommandTM, T7.190, T7.210 AutoCommandTM, T7.210, and T7.225 AutoCommandTM. The manual contains sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes, hydraulic systems, pneumatic system, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork and decals. Each section provides removal and installation instructions, specifications
This document is a service manual for a 1150L Crawler Dozer made in Brazil with a Tier 3 engine. The manual contains over 20 sections covering various systems of the dozer like the engine, transmission, brakes, hydraulics, tracks, electrical systems, and more. Each section includes subsections for components, with technical specifications, operational descriptions, troubleshooting information, and service procedures.
New holland tc5.30 combine harvesters service repair manual instant downloadufjjsjekksekmm
This document is a service manual for the TC5.30 combine with and without cab. It contains sections covering the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, crop storage and unloading, platform, cab, bodywork, and decals. The introduction provides a foreword and notes the technical information is written to support maintenance and servicing of the machine's functions and systems.
New holland tc5.30 combine harvesters service repair manualujfdjjskkemme
The document is a service manual that provides technical information for servicing a TC5.30 combine. It contains sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section contains chapters that provide technical data, functional data, diagnostic data, and service procedures for the components in that section of the combine.
Case 1650 l crawler dozer service repair manualujdjkkskmme
This service manual provides information on servicing and repair for a 1650L XLT PAT excavator. It includes sections covering the engine, rear axle system, hydrostatic drive, brakes and controls, hydraulic systems, tracks and track suspension, cab climate control, electrical systems, dozer blade and arm, tools, and platform, cab, bodywork, and decals. The manual provides specifications, diagrams, removal and installation instructions, and troubleshooting information to guide maintenance and repairs.
Case 1150 l crawler dozer service repair manualujjdfjkskdme
This service manual provides information on servicing and repairing various components of an 1150L XLT PAT machine, including the engine, rear axle system, hydrostatic drive, brakes and controls, hydraulic systems, tracks and track suspension, cab climate control, electrical systems, dozer blade and arm, tools, and platform, cab, bodywork, and decals. The manual is divided into sections covering each major component or system, and each section contains chapters on specific subcomponents or aspects of that system. Technical specifications, diagrams, removal and installation instructions, and troubleshooting information are provided.
New holland 7030 l grape harvester service repair manualufjsjjkksemme
This service manual section provides information on the engine and crankcase for the 7030L grape harvester. It includes an overview of key engine components such as the cooling system, exhaust treatment system, air cleaner, and pumps. It also provides details on servicing items like checking the engine oil level, replacing filters, and adjusting valve clearances. Maintenance procedures and specifications are included to support servicing of the engine and associated systems.
Hyster g007 (h12.00 xm) forklift parts catalogue manualfusjejfjskekem
This parts manual is divided into 14 major sections covering the various systems of the Challenger H8.00-12.00XM truck. Section 1 covers the frame and includes descriptions and illustrations of components such as the hood, cab, counterweight, floor plates, and labels. Repair procedures can be found in the service manual.
Hyster d024 (s155 ft) forklift service repair manualfusjejfjskekem
This document provides instructions for repairing the hydraulic gear pump assembly for various lift truck models. It describes removing the pump from the transmission housing and draining hydraulic fluid from the tank. The pump is then disassembled by removing housings, seals, gears, and plates. Individual parts are cleaned, inspected for wear, and replaced as needed. Reassembly involves installing new seals and plates and reattaching the housings. Finally, the pump is reinstalled on the transmission housing with fittings attached to hydraulic lines.
Hyster c114 (e35 xl) forklift service repair manualfusjejfjskekem
This document provides descriptions and diagrams of steering systems for lift trucks, including power steering and power steering with on-demand systems. It describes the main components such as the steering wheel, encoder, actuator, control unit, pump motor, and hydraulic cylinders or motors. Power steering systems use a hydraulic circuit to route pressurized fluid from the pump motor to steering components when the wheel is turned, while on-demand systems only operate the pump motor during steering wheel movement. The control unit routes hydraulic fluid to steer the truck based on wheel position. Diagrams show hydraulic and electrical configurations.
Hyster a917 (h800 hds) forklift service repair manualfusjejfjskekem
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Safety precautions are provided and components are labeled in diagrams.
Cummins onan generator set with power command 3100 controller model (dfeb ) s...fusjejfjskekem
This document is a service manual that provides information for troubleshooting and servicing generator sets that use PowerCommand 3100 controllers. It contains sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and safety instructions for working on the generator set and power control systems.
Caterpillar cat 320 e excavator (prefix klt) service repair manual (klt00001 ...fusjejfjskekem
This service repair manual provides instructions for removing and installing various components of the heating and air conditioning system on a 320E and 320E L excavator. The components include the actuator motor, control module, refrigerant receiver-dryer, and various ducts, hoses, and panels. Detailed illustrations accompany the step-by-step removal and installation procedures, which note safety precautions like using protective equipment when working with refrigerant and not smoking in refrigerant areas.
Caterpillar cat 320 c excavator (prefix gla) service repair manual (gla00001 ...fusjejfjskekem
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and bearings from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, driver groups and presses. The component weights range from 29 kg for the ring gear to 190 kg for the assembled swing drive.
Caterpillar cat 320 c excavator (prefix bea) service repair manual (bea00001 ...fusjejfjskekem
This document provides instructions for removing a bucket cylinder from an excavator. It begins by noting the importance of relieving pressure from hydraulic systems before disassembly to prevent injury. The steps include releasing hydraulic pressure, attaching lifting devices, removing retaining bolts and pins, and disconnecting hoses. Identification marks should be made on all lines and components. Cleanliness is important during disassembly and reassembly to prevent contamination of hydraulic systems.
This document provides instructions for installing an automatic timing advance on a 3306 engine. It involves using various tools to install a fuel pump timing pin and bolt to hold the automatic timing advance in place while tightening another bolt. The timing advance is then tightened to a specified torque and the tools are removed. Finally, the front housing is reinstalled.
This document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar 235 excavator engine. It describes using various tools to distort the wear sleeve and remove the old seal. When installing the new seal and sleeve, no lubricant should be used and retaining compound is applied to mate the surfaces. The flywheel housing is removed using link brackets and bolts, and installed by reversing the process.
Caterpillar cat 232 d skid steer loader (prefix kxc) service repair manual (k...fusjejfjskekem
1. The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C2.2 engine.
2. To remove the flywheel, mounting bolts must be removed and lifting tools installed to lift the heavy flywheel off of alignment dowels.
3. Flywheel installation requires cleaning surfaces, heating the ring gear for installation, aligning the flywheel on dowels, and torquing mounting bolts to the specified value.
4. Crankshaft rear seal removal requires removing the flywheel housing or back plate and pulling the old seal. Installation requires cleaning, applying sealant, pressing the new seal in place, and replacing the
The document provides instructions for removing and installing fuel system components on a Caterpillar 229 Excavator including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump and disassembling/assembling it.
- Installing the fuel transfer pump.
The instructions include safety notices and illustrations showing the component locations and part numbers. Procedures note removing bolts and hoses, checking gaskets, and reinstalling components in the reverse order of removal.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure and containing fluids during disassembly.
New holland w70 c tier 4b (final) compact wheel loader service repair manualfusjejfjskekem
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and radiator grids.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser (if equipped).
3. Put battery main switch in OFF position. Secure engine hood with lifting strap before removing hood hinge bolts.
New holland w70 c tier 4 compact wheel loader service repair manualfusjejfjskekem
This document is a service manual for compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, electrical systems, and cab. The manual provides instructions for maintenance and repair work to be performed by qualified dealership personnel using the specified tools and procedures.
This document provides instructions for assembling and disassembling components of the governor assembly and fuel injection pump on a 3034 engine for Caterpillar built machines. It describes how to assemble the governor control lever and fuel control lever, install the governor weight assembly and speed control lever. It also provides instructions for removing and installing the fuel injection pump, including cleaning surfaces, installing shims and dowels, and connecting linkages and springs.
Caterpillar cat 226 d skid steer loader (prefix hrd) service repair manual (h...fusjejfjskekem
This document provides instructions for removing and installing fuel injection lines and an exhaust cooler on a Caterpillar C2.2 engine. The summary is:
1) The document outlines the required tools and safety precautions for working on the fuel system and with sulfuric acid.
2) The procedure for removing the fuel injection lines includes disconnecting clamps and nuts, removing the lines, and installing capping kits on the injectors and manifold.
3) Installation involves reconnecting the lines with new isolators and gaskets, tightening all nuts and bolts to the specified torques, and priming the fuel system.
4) Removal of the exhaust cooler involves disconnecting hoses
New holland w60 tc wheel loader service repair manualfusjejfjskekem
This document provides repair manuals and technical specifications for W50TC, W60TC, W70TC, and W80TC wheel loaders. It includes sections on the engine, front and rear axles, braking system, hydraulic system, and their various components. Diagrams, dimensions, troubleshooting guides, and disassembly/reassembly instructions are provided to assist with maintenance and repairs.
New holland w60 c zb stage iiib compact wheel loader service repair manualfusjejfjskekem
This document provides instructions for removing an engine from a compact wheel loader. It begins with parking the machine securely and stopping the engine. The instructions then describe aligning mounting bores and securing the engine with a pin located on the machine frame.
New holland w50 wheel loader service repair manualfusjejfjskekem
The document is a workshop manual for wheel loaders that provides safety instructions for personnel. It contains sections on fundamental safety, operation safety, maintenance safety, repairs safety, and safety warnings. Personnel are instructed to carefully read all safety instructions, wear protective equipment, ensure only authorized trained staff perform repairs, and more. The workshop manual aims to protect operator safety and prevent accidents during operation and maintenance of the wheel loaders.
Case ih stx 280 tractor service repair manualfusjejfjskekem
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair, removal and installation procedures for various components. Key sections include engine repair information, lubrication requirements, air induction systems, electrical systems, steering components, and center consoles. The document directs the user to additional manuals for more detailed information on specific topics and components.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Hyster d024 (s155 ft) forklift service repair manualfusjejfjskekem
This document provides instructions for repairing the hydraulic gear pump assembly for various lift truck models. It describes removing the pump from the transmission housing and draining hydraulic fluid from the tank. The pump is then disassembled by removing housings, seals, gears, and plates. Individual parts are cleaned, inspected for wear, and replaced as needed. Reassembly involves installing new seals and plates and reattaching the housings. Finally, the pump is reinstalled on the transmission housing with fittings attached to hydraulic lines.
Hyster c114 (e35 xl) forklift service repair manualfusjejfjskekem
This document provides descriptions and diagrams of steering systems for lift trucks, including power steering and power steering with on-demand systems. It describes the main components such as the steering wheel, encoder, actuator, control unit, pump motor, and hydraulic cylinders or motors. Power steering systems use a hydraulic circuit to route pressurized fluid from the pump motor to steering components when the wheel is turned, while on-demand systems only operate the pump motor during steering wheel movement. The control unit routes hydraulic fluid to steer the truck based on wheel position. Diagrams show hydraulic and electrical configurations.
Hyster a917 (h800 hds) forklift service repair manualfusjejfjskekem
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Safety precautions are provided and components are labeled in diagrams.
Cummins onan generator set with power command 3100 controller model (dfeb ) s...fusjejfjskekem
This document is a service manual that provides information for troubleshooting and servicing generator sets that use PowerCommand 3100 controllers. It contains sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and safety instructions for working on the generator set and power control systems.
Caterpillar cat 320 e excavator (prefix klt) service repair manual (klt00001 ...fusjejfjskekem
This service repair manual provides instructions for removing and installing various components of the heating and air conditioning system on a 320E and 320E L excavator. The components include the actuator motor, control module, refrigerant receiver-dryer, and various ducts, hoses, and panels. Detailed illustrations accompany the step-by-step removal and installation procedures, which note safety precautions like using protective equipment when working with refrigerant and not smoking in refrigerant areas.
Caterpillar cat 320 c excavator (prefix gla) service repair manual (gla00001 ...fusjejfjskekem
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and bearings from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, driver groups and presses. The component weights range from 29 kg for the ring gear to 190 kg for the assembled swing drive.
Caterpillar cat 320 c excavator (prefix bea) service repair manual (bea00001 ...fusjejfjskekem
This document provides instructions for removing a bucket cylinder from an excavator. It begins by noting the importance of relieving pressure from hydraulic systems before disassembly to prevent injury. The steps include releasing hydraulic pressure, attaching lifting devices, removing retaining bolts and pins, and disconnecting hoses. Identification marks should be made on all lines and components. Cleanliness is important during disassembly and reassembly to prevent contamination of hydraulic systems.
This document provides instructions for installing an automatic timing advance on a 3306 engine. It involves using various tools to install a fuel pump timing pin and bolt to hold the automatic timing advance in place while tightening another bolt. The timing advance is then tightened to a specified torque and the tools are removed. Finally, the front housing is reinstalled.
This document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar 235 excavator engine. It describes using various tools to distort the wear sleeve and remove the old seal. When installing the new seal and sleeve, no lubricant should be used and retaining compound is applied to mate the surfaces. The flywheel housing is removed using link brackets and bolts, and installed by reversing the process.
Caterpillar cat 232 d skid steer loader (prefix kxc) service repair manual (k...fusjejfjskekem
1. The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar C2.2 engine.
2. To remove the flywheel, mounting bolts must be removed and lifting tools installed to lift the heavy flywheel off of alignment dowels.
3. Flywheel installation requires cleaning surfaces, heating the ring gear for installation, aligning the flywheel on dowels, and torquing mounting bolts to the specified value.
4. Crankshaft rear seal removal requires removing the flywheel housing or back plate and pulling the old seal. Installation requires cleaning, applying sealant, pressing the new seal in place, and replacing the
The document provides instructions for removing and installing fuel system components on a Caterpillar 229 Excavator including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump and disassembling/assembling it.
- Installing the fuel transfer pump.
The instructions include safety notices and illustrations showing the component locations and part numbers. Procedures note removing bolts and hoses, checking gaskets, and reinstalling components in the reverse order of removal.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure and containing fluids during disassembly.
New holland w70 c tier 4b (final) compact wheel loader service repair manualfusjejfjskekem
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and radiator grids.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser (if equipped).
3. Put battery main switch in OFF position. Secure engine hood with lifting strap before removing hood hinge bolts.
New holland w70 c tier 4 compact wheel loader service repair manualfusjejfjskekem
This document is a service manual for compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, electrical systems, and cab. The manual provides instructions for maintenance and repair work to be performed by qualified dealership personnel using the specified tools and procedures.
This document provides instructions for assembling and disassembling components of the governor assembly and fuel injection pump on a 3034 engine for Caterpillar built machines. It describes how to assemble the governor control lever and fuel control lever, install the governor weight assembly and speed control lever. It also provides instructions for removing and installing the fuel injection pump, including cleaning surfaces, installing shims and dowels, and connecting linkages and springs.
Caterpillar cat 226 d skid steer loader (prefix hrd) service repair manual (h...fusjejfjskekem
This document provides instructions for removing and installing fuel injection lines and an exhaust cooler on a Caterpillar C2.2 engine. The summary is:
1) The document outlines the required tools and safety precautions for working on the fuel system and with sulfuric acid.
2) The procedure for removing the fuel injection lines includes disconnecting clamps and nuts, removing the lines, and installing capping kits on the injectors and manifold.
3) Installation involves reconnecting the lines with new isolators and gaskets, tightening all nuts and bolts to the specified torques, and priming the fuel system.
4) Removal of the exhaust cooler involves disconnecting hoses
New holland w60 tc wheel loader service repair manualfusjejfjskekem
This document provides repair manuals and technical specifications for W50TC, W60TC, W70TC, and W80TC wheel loaders. It includes sections on the engine, front and rear axles, braking system, hydraulic system, and their various components. Diagrams, dimensions, troubleshooting guides, and disassembly/reassembly instructions are provided to assist with maintenance and repairs.
New holland w60 c zb stage iiib compact wheel loader service repair manualfusjejfjskekem
This document provides instructions for removing an engine from a compact wheel loader. It begins with parking the machine securely and stopping the engine. The instructions then describe aligning mounting bores and securing the engine with a pin located on the machine frame.
New holland w50 wheel loader service repair manualfusjejfjskekem
The document is a workshop manual for wheel loaders that provides safety instructions for personnel. It contains sections on fundamental safety, operation safety, maintenance safety, repairs safety, and safety warnings. Personnel are instructed to carefully read all safety instructions, wear protective equipment, ensure only authorized trained staff perform repairs, and more. The workshop manual aims to protect operator safety and prevent accidents during operation and maintenance of the wheel loaders.
Case ih stx 280 tractor service repair manualfusjejfjskekem
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair, removal and installation procedures for various components. Key sections include engine repair information, lubrication requirements, air induction systems, electrical systems, steering components, and center consoles. The document directs the user to additional manuals for more detailed information on specific topics and components.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
7. INTRODUCTION
Foreword
IMPORTANT INFORMATION
All repair and maintenance works listed in this manual must be carried out only by staff belonging to the NEW HOL-
LAND Service network, strictly complying with the instructions given and using, whenever required, the special tools.
Anyone who carries out the above operations without complying with the prescriptions shall be responsible for the
subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional or
local dealers, reject any responsibility for damages due to the anomalous behavior of parts and/or components not
approved by the manufacturer himself, including those used for the servicing or repair of the product manufactured
or marketed by the Manufacturer. In any case, no warranty is given or attributed on the product manufactured or
marketed by the Manufacturer in case of damages due to an anomalous behavior of parts and/or components not
approved by the Manufacturer.
No reproduction, though partial of text and illustrations allowed
47663637 18/02/2014
3
8. INTRODUCTION
Basic instructions - How to use and navigate through this manual
Technical Information
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through Web delivery (eTim), DVD and in paper manuals. A coding system called
SAP has been developed to link the technical information to other Product Support functions, e.g., Warranty.
Technical information is written to support the maintenance and service of the functions or systems on a customer's
machine. When a customer has a concern on his machine it is usually because a function or system on his machine
is not working at all, is not working efficiently, or is not responding correctly to his commands. When you refer to
the technical information in this manual to resolve that customer's concern, you will find all the information classified
using the SAP coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system then you will find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system, the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting) and the service data (remove, install adjust, etc.).
By integrating SAP coding into technical information, you will be able to search and retrieve just the right piece of
technical information you need to resolve that customer's concern on his machine. This is made possible by attaching
3 categories to each piece of technical information during the authoring process.
The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - is the component or function on the machine, that the piece of technical information is going to describe
e.g. Fuel tank.
• INFORMATION TYPE - is the piece of technical information that has been written for a particular component or
function on the machine e.g. Capacity would be a type of Technical Data that would describe the amount of fuel
held by the Fuel tank.
• PRODUCT - is the model for which the piece of technical information is written.
Every piece of technical information will have those 3 categories attached to it. You will be able to use any combination
of those categories to find the right piece of technical information you need to resolve that customer's concern on his
machine.
That information could be:
• the description of how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool
47663637 18/02/2014
4
9. INTRODUCTION
How to use this manual
This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the
end of a Chapter. Page number references are included for every piece of technical information listed in the Chapter
Contents or Chapter Index.
Each Chapter is divided into four Information types:
• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components and, assemblies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components and assemblies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hydraulic
devices, components and assemblies.
• Service Data (remove disassembly, assemble, install) for all the mechanical, electrical or hydraulic devices, com-
ponents and assemblies.
Sections
Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by a
number 00, 35, 55, etc. The amount of Sections included in the manual will depend on the type and function of the
machine that the manual is written for. Each Section has a Contents page listed in alphabetic/numeric order. This
table illustrates which Sections could be included in a manual for a particular product.
PRODUCT
Tractors
Vehicles with working arms: backhoes, excavators,
skid steers, ….
Combines, forage harvesters, balers, ….
Seeding, planting, floating, spraying
equipment, ….
SECTION Mounted equipment and tools, ….
00 - Maintenance
05 - Machine completion and equipment
10 - Engine
14 - Main gearbox and drive
18 - Clutch
21 - Transmission
23 - Four wheel drive system
25 - Front axle system
27 - Rear axle system
29 - Hydrostatic drive
31 - Implement power take-off
33 - Brakes and controls
35 - Hydraulic systems
36 - Pneumatic system
37 - Hitches, drawbars and implement couplings
39 - Frames and ballasting
41 - Steering
44 - Wheels
46 - Steering clutches
48 - Tracks and track suspension
50 - Cab climate control
55 - Electrical systems
56 - Grape harvester shaking
58 - Attachments/headers
60 - Product feeding
61 - Metering system
62 - Pressing - Bale formation
47663637 18/02/2014
5
10. INTRODUCTION
63 - Chemical applicators
64 - Chopping
66 - Threshing
68 - Tying/Wrapping/Twisting
69 - Bale wagons
70 - Ejection
71 - Lubrication system
72 - Separation
73 - Residue handling
74 - Cleaning
75 - Soil preparation/Finishing
76 - Secondary cleaning / Destemmer
77 - Seeding
78 - Spraying
79 - Planting
80 - Crop storage / Unloading
82 - Front loader and bucket
83 - Telescopic single arm
84 - Booms, dippers and buckets
86 - Dozer blade and arm
88 - Accessories
89 - Tools
90 - Platform, cab, bodywork and decals
47663637 18/02/2014
6
12. Engine - Engine air compressor
Air compressor - Static description
TC5070 WE
TC5080 WE
The air compressor (3) is a single cylinder, gear driven air compressor, which supplies air to a reservoir tank, enabling
the operator to have a source of compressed air for cleaning purposes and tyre inflation. The compressor is mounted
directly on the engine with the two nuts (10).
Engine oil is supplied through an internal connection with the engine, using engine oil pressure to lubricate the com-
pressor.
The compressed air is delivered through tubing to a combination pressure relief control valve, and from there to the
reservoir tank located on the straw hood of the combine. A quick disconnect fitting allows easy connection to the air
supply for blow off nozzles as well as for tyre inflation equipment.
ZEIL06CS0085A0B 1
47663637 18/02/2014
10.1 [10.450] / 3
13. Engine - Engine air compressor
Air compressor - Drawing
TC5070 WE
TC5080 WE
ZEIL11CX0668G0B 1
Reference Port Port Name Port Function
1 0 Inlet Port Supplies Compressor with clean intake air
2 2 Discharge Port Expels pressurized air for system
4 8.1 Oil Supply Supplies compressor with lube oil from engine
5 8.2 Oil Drain Allows lube oil to return to engine
6 9.1 Coolant Receive coolant from engine
7 9.2 Coolant Return coolant to engine
47663637 18/02/2014
10.1 [10.450] / 4
14. Engine - Engine air compressor
Compressed air tank Relief valve - Drawing
TC5070 WE
TC5080 WE
ZEIL11CX0667G0B 1
Reference Port Port name Port function
1 1 Inlet Pressurized air "in" from compressor
2 21 Outlet Pressurized air "out" to reservoir tank and blow
off line quick connect port
3 22 Auxiliary supply Auxiliary port not used in this application
4 1-2 Tire inflation device Port used to connect tire inflation device
5 3 Exhaust for compressor idling Discharge exhaust for excess pressure in system
47663637 18/02/2014
10.1 [10.450] / 5
15. Engine - Engine air compressor
Compressed air tank Relief valve - Static description
TC5070 WE
TC5080 WE
The pressure relief valve is developed to protect the system against pressures higher than 8 bar ( 116 psi).
Port (1) is connected to the air compressor, port (21) is connected to the pressurized reservoir.
When the pressure on port (21) reaches 8 bar ( 116 psi), the control valve (9d) will be activated which means that
also control valve (9c) will be activated. The pressure from the compressor will now pass through port (3).
If the pressure drops below 8 bar ( 116 psi) by activation a engaging valve, control valve (9d) will close.
Valve (9c) will not close immediately but will remain in the open position until the pressure exerted on the control of
valve (9c) will be reduced by 0.6 bar ( 8.7 psi). Then the air will pass through valve (9b).
Schematic diagram
ZDA7672Z 1
47663637 18/02/2014
10.1 [10.450] / 6
16. Engine - Engine air compressor
Air compressor - Remove
TC5070 WE
TC5080 WE
1. Bleed the air from the system by opening the drain (2)
at the bottom of the air reservoir.
ZEIL06TC00034A0 1
2. Loosen the retaining strap (1) and remove the air inlet
pipe (2) from the air compressor (3).
NOTE: Protect the air inlet and outlet ports from dirt
ingress.
3. Loosen the connection (4) to remove the hose (5) from
the air compressor (3).
ZEIL06CS0082A0B 2
4. Drain sufficient coolant from the engine cooling system
to allow removal of the coolant lines.
NOTE: Refer to the Operator’s Manual of your machine.
5. Loosen the connection (6).
ZEIL06CS0083A0B 3
6. Loosen the connection (7).
7. Remove the four bolts (8) to remove the support (9).
ZEIL06CS0084A0B 4
47663637 18/02/2014
10.1 [10.450] / 7
17. Engine - Engine air compressor
8. Remove the two nuts (10) to remove the air compressor
(3) from the engine.
ZEIL06CS0085A0B 5
47663637 18/02/2014
10.1 [10.450] / 8
18. Engine - Engine air compressor
Air compressor - Install
TC5070 WE
TC5080 WE
1. Install the air compressor (3) on the engine and tighten
the two nuts (10).
ZEIL06CS0085A0B 1
NOTE: Make sure that the O-ring (11) is positioned well. If
necessary apply grease.
ZEIL06CS0086A0B 2
2. Install the support (9) with the four bolts (8).
3. Install the tube and tighten the connection (7).
ZEIL06CS0084A0B 3
4. Install the tube and tighten the connection (6).
ZEIL06CS0083A0B 4
47663637 18/02/2014
10.1 [10.450] / 9
19. Engine - Engine air compressor
5. Install the hose (5) on the air compressor (3) and
tighten the connection (4).
6. Install the pipe (2) on the air compressor (3) and tighten
the retaining strap (1).
ZEIL06CS0082A0B 5
7. Close the drain (2) at the bottom of the reservoir.
8. Add engine coolant to the cooling system, refer to the
Operator’s Manual for more details.
9. Start the engine to charge the system with air. Allow the
air system to build up pressure to the governor cutout.
Stop the engine and use a soap and water solution at
the connection points to check for air leaks. Make any
necessary repairs.
ZEIL06TC00034A0 6
47663637 18/02/2014
10.1 [10.450] / 10
20. Transmission - Mechanical transmission
Mechanical transmission - Remove
TC5070 WE
TC5080 WE
NOTICE: Before removing any components, secure the machine safely in place by placing adequate wedges against
both traction and steering wheels.
1. On the left-hand side, remove the required covers by
loosening the bolts.
RNIL08TC0029A0A 1
2. Loosen the hose clamps (1) and (2).
RNIL08TC0030A0B 2
3. Support the hydrostatic motor (1) and loosen the four
nuts (2). (only two nuts are shown)
Pull the hydrostatic motor (1) out of the gearbox.
NOTE: In some cases it will be necessary to remove the
LHS traction wheel for taking the hydrostatic motor out of
the gearbox.
ZDA7815A 3
47663637 18/02/2014
21.1 [21.114] / 8
21. Transmission - Mechanical transmission
4. Disconnect the hand brake cable (1) by removing the
bolt.
RNIL08TC0031A0B 4
5. Disconnect the combine speed sensor (1).
RNIL08TC0032A0B 5
6. Disconnect the gearshift bar (4).
ZDA7817A 6
7. Disconnect the sleeves (1) and the brake lines on both
sides of the traction gearbox.
CAUTION
The gearbox is heavy (380 kg [838 lbs]). Take extreme
caution when removing the gearbox! Use a supporting
device which can handle this weight!
Z022
RNIL08TC0033A0B 7
47663637 18/02/2014
21.1 [21.114] / 9
22. Transmission - Mechanical transmission
8. Loosen the three bolts (1) at both sides of traction gear-
box.
Lower the traction gearbox and remove it from under-
neath the combine.
ZDA7818A 8
47663637 18/02/2014
21.1 [21.114] / 10
23. Transmission - Mechanical transmission
Mechanical transmission - Install
TC5070 WE
TC5080 WE
1. Bring the traction gearbox onto his place.
On both sides of the traction gearbox, install the three
bolts (1).
NOTE: Apply Loctite 242 (OMNIFIT 50M, PERMABOND
113) onto the bolts (1).
ZDA7818A 1
2. Connect the sleeves (1) and the brake lines on both
sides of the traction gearbox.
RNIL08TC0033A0B 2
3. Connect the gearshift bar (4).
Adjust, if necessary, refer to Shifting disk system -
Adjust Bar (21.145).
ZDA7817A 3
47663637 18/02/2014
21.1 [21.114] / 11
24. Transmission - Mechanical transmission
4. Connect the ground speed sensor (1).
RNIL08TC0032A0B 4
5. Connect the hand brake cable (1).
Adjust, if necessary, refer to Brake pedals - Adjust
(33.202).
RNIL08TC0031A0B 5
6. Support the weight of the hydrostatic motor (1).
Raise the motor into position on the traction gearbox.
Apply grease onto the spline shaft of the motor (1).
Engage the spline shaft of the motor and push it into
the female spline until the mounting flange is against
the transmission.
Install the four nuts (2).
NOTE: Before install the four nuts, apply Loctite 270 (OM-
NIFIT 200M, PERMABOND 118).
ZDA7815A 6
7. Install the hose clamps (1) and (2).
RNIL08TC0030A0B 7
47663637 18/02/2014
21.1 [21.114] / 12
25. Transmission - Mechanical transmission
8. Install the removed covers and tighten the bolts.
RNIL08TC0029A0A 8
Next operation:
Hydraulic service brakes - Bleed (33.202).
47663637 18/02/2014
21.1 [21.114] / 13
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Transmission - Mechanical transmission external controls
Transmission housing cover - Disassemble
TC5060 WE
NOTE: Refer to Shifting disk system - Exploded view (21.145)
1. Loosen the drain plug and drain the oil from the gear-
box. Refer to the Operator's Manual: "SECTION 4
- LUBRICATION AND MAINTENANCE" paragraph
headed: "Traction gearbox".
2. Loosen the plug (112) with the seal ring (113) and the
breather (114).
ZEIL08TC0466A0B 1
3. Loosen the bolts (2) and remove the cover (1) of the
gearbox.
ZEIL08TC0303A0B 2
4. Loosen the bolt (3) from the gear shift finger (6).
ZEIL08TC0463A0B 3
47663637 18/02/2014
21.2 [21.130] / 10
28. Transmission - Mechanical transmission external controls
5. Remove the gear shift shaft (4) from the cover (1).
NOTICE: When removing the plate (5), mark it because it
is not symmetrical.
6. Remove the plate (5) and the gear shift finger (6) from
the cover (1).
ZEIL08TC0305A0B 4
7. Remove the shaft seals (7) from the cover (1) using a
screw driver.
ZEIL08TC0306A0B 5
47663637 18/02/2014
21.2 [21.130] / 11
29. Transmission - Mechanical transmission external controls
Transmission housing cover - Assemble
TC5060 WE
NOTE: Refer to Shifting disk system - Exploded view (21.145)
1. Install both shaft seals (7) in the cover (1).
ZEIL08TC0462A0B 1
NOTICE: The plate (5) must be assembled in such a way that the teeth are in a centralized position in relation to the
cover.
2. Position the gear shift finger (6) and the plate (5).
3. Install the gear shift shaft (4), fix as shown the gear shift
finger (6) with the bolt (3) using LOCTITE® 243. Tighten
with a torque of 46 Nm (33.9 lb ft).
ZEIL08TC0463A0B 2
4. Install the cover (1) applying LOCTITE® 574 on the con-
tact surface and fix it with the bolts (2), tighten with a
torque of 23 Nm (17.0 lb ft).
ZEIL08TC0465A0B 3
47663637 18/02/2014
21.2 [21.130] / 12
30. Transmission - Mechanical transmission external controls
5. Install the plug (112) with the seal ring (113) in the cover
(1). Tighten the plug (112) with a torque of 200 N·m
(147.5 lb ft).
6. Install the breather (114) on the plug (112) and tighten
with a torque of 12.1 N·m (8.9 lb ft).
ZEIL08TC0466A0B 4
7. Install the drain plug (115) and the level plug (121) and
tighten with a torque of 50 Nm (36.9 lb ft).
Fill the gearbox (9) with oil. Refer to the Operator's
Manual: "SECTION 4 - LUBRICATION AND MAINTE-
NANCE" paragraph headed: "Traction gearbox".
ZEIL08TC0467A0B 5
47663637 18/02/2014
21.2 [21.130] / 13