This document provides instructions to separate the tractor into three main components:
1) Separating the engine from the front transmission box by removing bolts and using a hoist and floor jack for support.
2) Separating the engine/frame assembly by removing components like the muffler, exhaust, radiator, and attaching a hoist to the engine.
3) Separating the engine from the frame by removing items like the firewall, air cleaner, and power steering lines and using a hoist to lift the engine. Detailed steps are provided to properly separate each component safely.
Case ih farmall 40 b cvt compact tractor service repair manual (pin zcme21001...fujsjefjskekmme
This document provides instructions to separate the engine from the rest of the tractor for service or repair. The key steps include removing the hood, cab, radiator, exhaust components, fuel and hydraulic lines, and electrical wiring. The engine is then separated from the front transmission box using a hoist and floor jack for support. Finally, the engine mounting bolts are loosened and removed to separate the engine from the frame.
Kawasaki 90 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component descriptions for a machine. It outlines various hazards to avoid when operating or servicing the machine, such as ensuring safety before leaving the operator's seat, wearing protective clothing, and avoiding contact with moving parts. It also describes the machine's components, including the operator's station, consoles, switches, and monitoring systems. Maintenance procedures should follow safety practices like supporting the machine properly and avoiding high-pressure fluids.
This document is an operation and maintenance manual for a wheel loader model 95Z7B powered by an Isuzu 6WG1 engine. It contains safety information, component names, operating instructions, maintenance procedures, and troubleshooting guides. The manual instructs operators to read it thoroughly before operating the machine to learn how to properly operate and service it.
Case ih patriot 3340 tier 4 b (final) sprayer service repair manual (pin ygt0...fujjdfjkksekmem
This document provides an overview of safety information and guidelines for Patriot® 3240 and 3340 sprayers. It emphasizes the importance of following all safety messages and warnings to avoid potential injury or death. A "Do Not Operate" tag should be attached whenever service is required to clearly indicate that the machine should not be used until repairs are complete. Personal protective equipment should always be worn when operating or servicing agricultural equipment.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Case 570 n ep tier 4b (final) tractor loader service repair manualfusjejfskekfmsme
This document provides service information for a Case 570N EP tractor, including specifications and maintenance procedures for the engine and other components. It includes specifications for the Tier 4B compliant engine such as bore, stroke, displacement and fuel injection details. It also provides instructions for draining and filling the engine oil, and lists the recommended oil type. Safety warnings are provided throughout advising technicians to follow proper safety procedures when servicing the machine.
New holland speedrower 240 self propelled windrower service repair manualufjjsekkemmd
The document is a service manual that provides information on the Speedrower 200 and 240 self-propelled windrowers, including:
- The engines are 6.7L, 6-cylinder turbocharged diesel engines producing 142 kW of power.
- The manual contains sections on the engine systems, front and rear axles, hydrostatic drive, power take-off, brakes, hydraulic systems, steering, cab climate control, electrical systems, attachments/headers, and bodywork/decals.
- Each section provides part numbers, specifications, diagrams and instructions for servicing and repairing components.
Case ih farmall 45 b cvt compact tractor service repair manual (pin zcme21001...jfdjjskekksemm
This document provides instructions to separate the engine from the rest of the tractor for service or repair. The key steps include removing the hood, cab, radiator, exhaust components, fuel and hydraulic lines, and electrical wiring. The engine is then separated from the front transmission box using a hoist and floor jack for support. Finally, the engine mounting bolts are loosened and removed to separate the engine from the frame.
Case ih farmall 40 b cvt compact tractor service repair manual (pin zcme21001...fujsjefjskekmme
This document provides instructions to separate the engine from the rest of the tractor for service or repair. The key steps include removing the hood, cab, radiator, exhaust components, fuel and hydraulic lines, and electrical wiring. The engine is then separated from the front transmission box using a hoist and floor jack for support. Finally, the engine mounting bolts are loosened and removed to separate the engine from the frame.
Kawasaki 90 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component descriptions for a machine. It outlines various hazards to avoid when operating or servicing the machine, such as ensuring safety before leaving the operator's seat, wearing protective clothing, and avoiding contact with moving parts. It also describes the machine's components, including the operator's station, consoles, switches, and monitoring systems. Maintenance procedures should follow safety practices like supporting the machine properly and avoiding high-pressure fluids.
This document is an operation and maintenance manual for a wheel loader model 95Z7B powered by an Isuzu 6WG1 engine. It contains safety information, component names, operating instructions, maintenance procedures, and troubleshooting guides. The manual instructs operators to read it thoroughly before operating the machine to learn how to properly operate and service it.
Case ih patriot 3340 tier 4 b (final) sprayer service repair manual (pin ygt0...fujjdfjkksekmem
This document provides an overview of safety information and guidelines for Patriot® 3240 and 3340 sprayers. It emphasizes the importance of following all safety messages and warnings to avoid potential injury or death. A "Do Not Operate" tag should be attached whenever service is required to clearly indicate that the machine should not be used until repairs are complete. Personal protective equipment should always be worn when operating or servicing agricultural equipment.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Case 570 n ep tier 4b (final) tractor loader service repair manualfusjejfskekfmsme
This document provides service information for a Case 570N EP tractor, including specifications and maintenance procedures for the engine and other components. It includes specifications for the Tier 4B compliant engine such as bore, stroke, displacement and fuel injection details. It also provides instructions for draining and filling the engine oil, and lists the recommended oil type. Safety warnings are provided throughout advising technicians to follow proper safety procedures when servicing the machine.
New holland speedrower 240 self propelled windrower service repair manualufjjsekkemmd
The document is a service manual that provides information on the Speedrower 200 and 240 self-propelled windrowers, including:
- The engines are 6.7L, 6-cylinder turbocharged diesel engines producing 142 kW of power.
- The manual contains sections on the engine systems, front and rear axles, hydrostatic drive, power take-off, brakes, hydraulic systems, steering, cab climate control, electrical systems, attachments/headers, and bodywork/decals.
- Each section provides part numbers, specifications, diagrams and instructions for servicing and repairing components.
Case ih farmall 45 b cvt compact tractor service repair manual (pin zcme21001...jfdjjskekksemm
This document provides instructions to separate the engine from the rest of the tractor for service or repair. The key steps include removing the hood, cab, radiator, exhaust components, fuel and hydraulic lines, and electrical wiring. The engine is then separated from the front transmission box using a hoist and floor jack for support. Finally, the engine mounting bolts are loosened and removed to separate the engine from the frame.
Case ih farmall 50 b cvt compact tractor service repair manual (pin zcme21001...jfjskeksemm
This document provides instructions to separate the engine from the rest of the tractor for service or repair. The key steps include removing the hood, cab, radiator, exhaust components, fuel and hydraulic lines, and electrical wiring. The engine is then separated from the front transmission box using a hoist and floor jack for support. Finally, the engine mounting bolts are loosened and removed to separate the engine from the frame.
Case ih farmall 50 b cvt compact tractor service repair manual (pin zcme21001...jfdjjskfkksmemm
This document provides instructions to separate the engine from the rest of the tractor for service or repair. The key steps include removing the hood, cab, radiator, exhaust components, fuel and hydraulic lines, and electrical wiring. The engine is then separated from the front transmission box using a hoist and floor jack for support. Finally, the engine mounting bolts are loosened and removed to separate the engine from the frame.
Case ih farmall 40 b cvt compact tractor service repair manual (pin zcme21001...jfdjjskekksemm
This document is a service manual for Farmall 40B CVT, 45B CVT, and 50B CVT compact tractors, providing information on engine systems, transmission, four-wheel drive, front and rear axle systems, power take-off, brakes, hydraulics, steering, cab climate control, electrical systems, and the platform, cab, and bodywork. The manual contains sections on maintenance and repair of these various tractor systems. Safety precautions are provided throughout for the protection of service personnel.
Case ih farmall 45 b cvt compact tractor service repair manual (pin zcme21001...jfjskeksemm
This document is a service manual for Farmall 40B CVT, 45B CVT, and 50B CVT compact tractors, providing information on engine systems, transmission, four-wheel drive, front and rear axle systems, power take-off, brakes, hydraulics, steering, cab climate control, electrical systems, and the platform, cab, and bodywork. The manual contains sections on maintenance and repair of these various tractor systems, illustrated with diagrams. Safety precautions are provided throughout for the protection of service personnel.
Case ih patriot 3240 tier 4 b (final) sprayer service repair manual (pin ygt0...fjsjekkdmme
This document provides service information for Case IH Patriot 3240 and 3340 sprayers with Tier 4B engines, including removal and installation instructions for the engine. The removal process involves disconnecting hoses, wires, and other components to separate the engine from the machine. Installation is the reverse of removal.
Case ih patriot 3340 tier 4 b (final) sprayer service repair manual (pin ygt0...fujskekfksmem
The document is a service manual that provides instructions for removing and installing an engine. It includes 31 numbered steps to remove the engine, such as disconnecting wiring harnesses, hoses, and removing mounting bolts. It then lists 4 steps to reinstall the engine, which involves using an overhead crane to lift the engine back into place and reattaching mounting hardware.
Case ih patriot 3240 tier 4 b (final) sprayer service repair manual (pin ygt0...fujskeksmemqa
This document provides an overview of safety information for Patriot 3240 and 3340 sprayers. It emphasizes the importance of following all safety messages and warnings to avoid potential injury or death. A "Do Not Operate" tag should be attached whenever service is required to clearly indicate that the machine should not be used until repairs are complete. Personal protective equipment should always be worn when operating or servicing agricultural equipment.
Case ih patriot 3340 tier 4 b (final) sprayer service repair manual (pin ygt0...fuekdksmemm
The document is a service manual that provides instructions for removing and installing an engine. It includes 31 numbered steps to remove the engine by disconnecting various components like hoses, wires, and mounts. The 34 steps to install the engine describe reconnecting components and mounting the engine back into place.
Case ih patriot 3240 tier 4 b (final) sprayer service repair manual (pin ygt0...ufujjdjkskemme
The document is a service manual that provides instructions for removing and installing an engine. It includes 31 numbered steps to remove the engine, such as disconnecting wiring harnesses, hoses, belts, and removing mounting hardware. It then lists 4 steps to reinstall the engine, which involves using an overhead crane to lift the engine back into place and reattaching the mounting hardware.
Caterpillar cat 345 b series ii excavator (prefix dcw) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176 engine. The removal procedure involves removing components like the valve mechanism cover, rocker shaft, and pushrods. Sensors and tubes must be disconnected from the cylinder head before removing bolts and lifting the head off. For installation, the mating surfaces are cleaned and the correct gasket is installed before lowering the head onto the cylinder block and installing bolts.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 3176C engine. It involves cleaning surfaces, installing gaskets and seals, lifting the cylinder head into place using guide bolts, and tightening head bolts in a specific sequence to the correct torque specifications. Sensors and wiring are then reconnected, coolant is added to the system, and remaining components like the rocker shaft and pushrods are reinstalled to complete the job.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head bolts are then removed and the head lifted off using a suitable lifting device. For installation, the mating surfaces are cleaned and new gaskets installed before positioning the cylinder head on the block and installing the bolts.
Caterpillar cat 345 c excavator (prefix dhp) service repair manual (dhp00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and piston assemblies. It notes to mark parts for reinstallation and clean components to prevent contamination. Reassembly follows the reverse order of disassembly.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor using different tools. These components include the head, plates, seals, pins, brake piston, disks, rotating group, shaft assembly, barrels, seals, and more. It notes to mark parts for reinstallation and clean components thoroughly. The assembly procedure is listed but not described in detail.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly process and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...fujsekfkksemm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, reinstalling these components in reverse order and noting to clean all parts, apply lubricant, and replace all seals and gaskets. Precise measurements and tooling are required to properly assemble the travel motor.
Caterpillar cat 345 c l excavator (prefix scn) service repair manual (scn0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C L excavator. It details removing over 30 individual components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly follows the reverse order, with notes to reinstall parts in their original positions and orientations. Required tools include transmission stands, eyebolts, retaining ring pliers, and seal installers.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C L Excavator. The disassembly process involves removing over 20 individual parts from the final drive housing including gears, shafts, bearings, seals and other components. Proper identification of part locations and orientations is emphasized for reassembly. Required tools include lifting devices, retaining ring pliers, eyebolts and other specialized tools.
Caterpillar cat 345 c l excavator (prefix spc) service repair manual (spc0000...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor including removing the head, brake piston, disks, rotating group, piston assemblies, seals and more. Detailed illustrations are provided to identify each part. When assembling, the instructions note to clean all parts and reinstall components in their original locations and orientations. Precautions are outlined to contain fluids, avoid damage, and prevent contamination.
Caterpillar cat 345 c l excavator (prefix wde) service repair manual (wde0000...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly steps and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 b l excavator (prefix 9cw) service repair manual (9cw0000...fujsekfkksemm
This document provides instructions for removing and installing the rocker shaft, pushrods, and cylinder head on a Caterpillar 345B L excavator engine. The removal procedure involves removing covers, shafts, rods, sensors and manifolds. The cylinder head is then lifted off. The installation procedure specifies cleaning components, installing gaskets and seals, and torquing bolts to specifications when reassembling the cylinder head and related parts.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. It describes cleaning and inspecting the cylinder head and block mating surfaces. The correct cylinder head gasket must be installed, along with new O-rings. The cylinder head is placed on guide bolts and bolts are tightened in a specific sequence to the correct torques. Sensors and lines are then reconnected to the cylinder head before installing the water outlet manifold.
More Related Content
Similar to Case ih farmall 40 b cvt compact tractor service repair manual (pin zcme21001 and above)
Case ih farmall 50 b cvt compact tractor service repair manual (pin zcme21001...jfjskeksemm
This document provides instructions to separate the engine from the rest of the tractor for service or repair. The key steps include removing the hood, cab, radiator, exhaust components, fuel and hydraulic lines, and electrical wiring. The engine is then separated from the front transmission box using a hoist and floor jack for support. Finally, the engine mounting bolts are loosened and removed to separate the engine from the frame.
Case ih farmall 50 b cvt compact tractor service repair manual (pin zcme21001...jfdjjskfkksmemm
This document provides instructions to separate the engine from the rest of the tractor for service or repair. The key steps include removing the hood, cab, radiator, exhaust components, fuel and hydraulic lines, and electrical wiring. The engine is then separated from the front transmission box using a hoist and floor jack for support. Finally, the engine mounting bolts are loosened and removed to separate the engine from the frame.
Case ih farmall 40 b cvt compact tractor service repair manual (pin zcme21001...jfdjjskekksemm
This document is a service manual for Farmall 40B CVT, 45B CVT, and 50B CVT compact tractors, providing information on engine systems, transmission, four-wheel drive, front and rear axle systems, power take-off, brakes, hydraulics, steering, cab climate control, electrical systems, and the platform, cab, and bodywork. The manual contains sections on maintenance and repair of these various tractor systems. Safety precautions are provided throughout for the protection of service personnel.
Case ih farmall 45 b cvt compact tractor service repair manual (pin zcme21001...jfjskeksemm
This document is a service manual for Farmall 40B CVT, 45B CVT, and 50B CVT compact tractors, providing information on engine systems, transmission, four-wheel drive, front and rear axle systems, power take-off, brakes, hydraulics, steering, cab climate control, electrical systems, and the platform, cab, and bodywork. The manual contains sections on maintenance and repair of these various tractor systems, illustrated with diagrams. Safety precautions are provided throughout for the protection of service personnel.
Case ih patriot 3240 tier 4 b (final) sprayer service repair manual (pin ygt0...fjsjekkdmme
This document provides service information for Case IH Patriot 3240 and 3340 sprayers with Tier 4B engines, including removal and installation instructions for the engine. The removal process involves disconnecting hoses, wires, and other components to separate the engine from the machine. Installation is the reverse of removal.
Case ih patriot 3340 tier 4 b (final) sprayer service repair manual (pin ygt0...fujskekfksmem
The document is a service manual that provides instructions for removing and installing an engine. It includes 31 numbered steps to remove the engine, such as disconnecting wiring harnesses, hoses, and removing mounting bolts. It then lists 4 steps to reinstall the engine, which involves using an overhead crane to lift the engine back into place and reattaching mounting hardware.
Case ih patriot 3240 tier 4 b (final) sprayer service repair manual (pin ygt0...fujskeksmemqa
This document provides an overview of safety information for Patriot 3240 and 3340 sprayers. It emphasizes the importance of following all safety messages and warnings to avoid potential injury or death. A "Do Not Operate" tag should be attached whenever service is required to clearly indicate that the machine should not be used until repairs are complete. Personal protective equipment should always be worn when operating or servicing agricultural equipment.
Case ih patriot 3340 tier 4 b (final) sprayer service repair manual (pin ygt0...fuekdksmemm
The document is a service manual that provides instructions for removing and installing an engine. It includes 31 numbered steps to remove the engine by disconnecting various components like hoses, wires, and mounts. The 34 steps to install the engine describe reconnecting components and mounting the engine back into place.
Case ih patriot 3240 tier 4 b (final) sprayer service repair manual (pin ygt0...ufujjdjkskemme
The document is a service manual that provides instructions for removing and installing an engine. It includes 31 numbered steps to remove the engine, such as disconnecting wiring harnesses, hoses, belts, and removing mounting hardware. It then lists 4 steps to reinstall the engine, which involves using an overhead crane to lift the engine back into place and reattaching the mounting hardware.
Similar to Case ih farmall 40 b cvt compact tractor service repair manual (pin zcme21001 and above) (9)
Caterpillar cat 345 b series ii excavator (prefix dcw) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176 engine. The removal procedure involves removing components like the valve mechanism cover, rocker shaft, and pushrods. Sensors and tubes must be disconnected from the cylinder head before removing bolts and lifting the head off. For installation, the mating surfaces are cleaned and the correct gasket is installed before lowering the head onto the cylinder block and installing bolts.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 3176C engine. It involves cleaning surfaces, installing gaskets and seals, lifting the cylinder head into place using guide bolts, and tightening head bolts in a specific sequence to the correct torque specifications. Sensors and wiring are then reconnected, coolant is added to the system, and remaining components like the rocker shaft and pushrods are reinstalled to complete the job.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head bolts are then removed and the head lifted off using a suitable lifting device. For installation, the mating surfaces are cleaned and new gaskets installed before positioning the cylinder head on the block and installing the bolts.
Caterpillar cat 345 c excavator (prefix dhp) service repair manual (dhp00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and piston assemblies. It notes to mark parts for reinstallation and clean components to prevent contamination. Reassembly follows the reverse order of disassembly.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor using different tools. These components include the head, plates, seals, pins, brake piston, disks, rotating group, shaft assembly, barrels, seals, and more. It notes to mark parts for reinstallation and clean components thoroughly. The assembly procedure is listed but not described in detail.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly process and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...fujsekfkksemm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, reinstalling these components in reverse order and noting to clean all parts, apply lubricant, and replace all seals and gaskets. Precise measurements and tooling are required to properly assemble the travel motor.
Caterpillar cat 345 c l excavator (prefix scn) service repair manual (scn0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C L excavator. It details removing over 30 individual components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly follows the reverse order, with notes to reinstall parts in their original positions and orientations. Required tools include transmission stands, eyebolts, retaining ring pliers, and seal installers.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fujsekfkksemm
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C L Excavator. The disassembly process involves removing over 20 individual parts from the final drive housing including gears, shafts, bearings, seals and other components. Proper identification of part locations and orientations is emphasized for reassembly. Required tools include lifting devices, retaining ring pliers, eyebolts and other specialized tools.
Caterpillar cat 345 c l excavator (prefix spc) service repair manual (spc0000...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor including removing the head, brake piston, disks, rotating group, piston assemblies, seals and more. Detailed illustrations are provided to identify each part. When assembling, the instructions note to clean all parts and reinstall components in their original locations and orientations. Precautions are outlined to contain fluids, avoid damage, and prevent contamination.
Caterpillar cat 345 c l excavator (prefix wde) service repair manual (wde0000...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly steps and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 b l excavator (prefix 9cw) service repair manual (9cw0000...fujsekfkksemm
This document provides instructions for removing and installing the rocker shaft, pushrods, and cylinder head on a Caterpillar 345B L excavator engine. The removal procedure involves removing covers, shafts, rods, sensors and manifolds. The cylinder head is then lifted off. The installation procedure specifies cleaning components, installing gaskets and seals, and torquing bolts to specifications when reassembling the cylinder head and related parts.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. It describes cleaning and inspecting the cylinder head and block mating surfaces. The correct cylinder head gasket must be installed, along with new O-rings. The cylinder head is placed on guide bolts and bolts are tightened in a specific sequence to the correct torques. Sensors and lines are then reconnected to the cylinder head before installing the water outlet manifold.
Caterpillar cat 345 b excavator (prefix ayr) service repair manual (ayr00001 ...fujsekfkksemm
This document provides instructions for disassembling and assembling the final drive components of an excavator model 345B. It describes removing 27 components including the travel motor, final drive, carrier assemblies, ring gear, and sprocket housing. Detailed illustrations and notes are provided to aid in correctly identifying parts and maintaining proper orientation during reassembly. Required tools include various link brackets, retaining ring pliers, seal installer, anti-seize compound, grease, thread lock, gasket sealant and a transmission stand.
Caterpillar cat 345 b excavator (prefix amn) service repair manual (amn00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pistons, bearings and housing. It also lists tools required for the job and safety notices about keeping parts clean and containing fluids.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
Caterpillar cat 345 b excavator (prefix amd) service repair manual (amd00001 ...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1) It describes preparing the travel motor body by installing seals, pistons, and spacers.
2) It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and plates.
3) It outlines attaching the head, installing valves and plugs, and filling the travel motor with oil before operation.
Caterpillar cat 345 b excavator (prefix 8kw) service repair manual (8kw00001 ...fujsekfkksemm
This document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Excavator engine. The removal process involves removing covers, shafts, rods, sensors, tubes, and manifolds before lifting the cylinder head off. The installation process specifies cleaning, inspecting, and lubricating components before lowering the cylinder head back onto the engine and reinstalling related parts in reverse order of removal. Tools and torque specifications are listed for select steps.
Caterpillar cat 345 b excavator (prefix 6mw) service repair manual (6mw00001 ...fujsekfkksemm
The document provides instructions for disassembling and assembling the travel motor of a 345B Excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. It then lists 15 steps for assembly, reversing the disassembly process and including inspecting parts and ensuring cleanliness to prevent contamination. The overall document provides detailed technical instructions for servicing the excavator's travel motor.
Caterpillar cat 340 f excavator (prefix sgh) service repair manual (sgh00001 ...fujsekfkksemm
The document provides disassembly instructions for a swing drive on a 340F excavator model. It begins by having the technician remove the swing drive and mark parts for reassembly. Several internal components of the swing drive are then removed, including planetary gears, shafts, rings, and housings. Precision tools are required and technicians should be careful due to the weights of parts removed. Cleanliness is emphasized to prevent contamination of hydraulic systems during repair.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
8. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your CASE IH Sales and Service Networks.
48080062 10/11/2016
3
9. INTRODUCTION
Safety rules
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
48080062 10/11/2016
5
10. INTRODUCTION
Safety rules - Ecology and the environment
Soil, air, and water quality is important for all industries and life in general. When legislation does not yet rule the
treatment of some of the substances that advanced technology requires, sound judgment should govern the use and
disposal of products of a chemical and petrochemical nature.
Familiarize yourself with the relative legislation applicable to your country, and make sure that you understand this
legislation. Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, anti-freeze,
cleaning agents, etc., with regard to the effect of these substances on man and nature and how to safely store, use,
and dispose of these substances.
Helpful hints
• Avoid the use of cans or other inappropriate pressurized fuel delivery systems to fill tanks. Such delivery systems
may cause considerable spillage.
• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of these products contain substances
that may be harmful to your health.
• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
• Avoid spillage when you drain fluids such as used engine coolant mixtures, engine oil, hydraulic fluid, brake fluid,
etc. Do not mix drained brake fluids or fuels with lubricants. Store all drained fluids safely until you can dispose of
the fluids in a proper way that complies with all local legislation and available resources.
• Do not allow coolant mixtures to get into the soil. Collect and dispose of coolant mixtures properly.
• The air-conditioning system contains gases that should not be released into the atmosphere. Consult an air-condi-
tioning specialist or use a special extractor to recharge the system properly.
• Repair any leaks or defects in the engine cooling system or hydraulic system immediately.
• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
• Protect hoses during welding. Penetrating weld splatter may burn a hole or weaken hoses, allowing the loss of oils,
coolant, etc.
Battery recycling
Batteries and electric accumulators contain several substances that can have a harmful
effect on the environment if the batteries are not properly recycled after use. Improper
disposal of batteries can contaminate the soil, groundwater, and waterways. CASE IH
strongly recommends that you return all used batteries to a CASE IH dealer, who will
dispose of the used batteries or recycle the used batteries properly. In some countries,
this is a legal requirement.
Mandatory battery recycling
NOTE: The following requirements are mandatory in Brazil.
Batteries are made of lead plates and a sulfuric acid solution. Because batteries contain heavy metals such as lead,
CONAMA Resolution 401/2008 requires you to return all used batteries to the battery dealer when you replace any
batteries. Do not dispose of batteries in your household garbage.
Points of sale are obliged to:
• Accept the return of your used batteries
• Store the returned batteries in a suitable location
• Send the returned batteries to the battery manufacturer for recycling
48080062 10/11/2016
6
12. Engine - Engine and crankcase
Engine - Remove Separating the tractor at the engine - front
transmission box
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
NOTE: To separate the tractor between the engine and the
front transmission box, the hood and cab must be removed.
To accomplish this, see “Platform” Section 90, for removal
procedures.
1. Remove the negative (-) battery cable, (1), and the pos-
itive (+) battery cable, (2), from the battery.
76083810N 1
2. Disconnect the power steering return hose, (1), from
the hydraulic system inlet tube, (2). Remove the hy-
draulic system inlet tube, (2), from the hydraulic pump,
(3).
3. Remove the hydraulic system pressure tube, (4), from
the hydraulic pump, (3), and the diverter valve.
76075731N 2
48080062 10/11/2016
10.1 [10.001] / 8
13. Engine - Engine and crankcase
4. Disconnect the wires, (1), on the starter, (2), and re-
move the starter from the tractor.
30997565N 3
5. If equipped with FWD, remove the roll pins, (1), from the
front and rear of the FWD driveshaft, (2), and remove
the driveshaft from the tractor.
6. Drain the engine oil into a suitable container and re-
move the oil filter.
20000904N 4
48080062 10/11/2016
10.1 [10.001] / 9
14. Engine - Engine and crankcase
7. Remove the fuel supply, (1), and return, (2), lines from
the fuel filter, (3).
8. Drain the fuel tank into a suitable container.
76075737N 5
9. Attach a chain sling, (1), to the two hoist eyes, (2).and
(3), on the engine.
76075738N 6
10. Attach a suitable hoist, (1), to the chain sling, (2).
NOTE: The hoist is used for supporting the engine and axle
assembly, not for lifting.
11. Roll a floor jack under the tractor from the rear of the
tractor, and place under the front transmission box.
Raise the jack enough to support the drive train.
76083809N 7
48080062 10/11/2016
10.1 [10.001] / 10
15. Engine - Engine and crankcase
12. Remove the buckle-up bolts, (1), that secure the en-
gine, (2), to the front transmission box, (3).
NOTE: The hoist and/or the floor jack may need to be
raised or lowered to allow the separation of the engine from
the front transmission box.
13. Carefully roll the drive train away from the engine, us-
ing the floor jack for support.
76083811N 8
48080062 10/11/2016
10.1 [10.001] / 11
16. Engine - Engine and crankcase
Engine - Remove Separating the tractor at the engine/frame
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
DANGER
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply will result in death or serious injury.
D0076A
1. Use jack stands under the frame rails to support the
front frame/engine assembly.
2. Remove the chain sling from the two hoist eyes on the
engine.
3. Remove the power steering lines, (1), from the power
steering control motor, (2), the frame, (3), and the
power steering pump, (4).
76075732N 1
48080062 10/11/2016
10.1 [10.001] / 12
17. Engine - Engine and crankcase
4. Remove the air cleaner assembly, (1), from the firewall,
(2).
76083813N 2
5. Remove the muffler guard, (1), from the tractor.
30996394N 3
6. Remove the muffler, (1), and the exhaust pipe, (2), from
the tractor.
7. Drain the coolant from the radiator into a suitable con-
tainer.
8. Remove the top, (3), and the bottom, (4), radiator
hoses.
9. Remove the radiator, (5), and the oil cooler (if
equipped) from the tractor.
76083814N 4
48080062 10/11/2016
10.1 [10.001] / 13
18. Engine - Engine and crankcase
10. Remove the firewall, (1), and the air cleaner mounting
bracket, (2), from the engine.
11. Attach a chain sling to the two hoist eyes on the en-
gine.
12. Attach a suitable hoist to the chain sling, and raise the
hoist enough to support the engine.
76083812N 5
13. Loosen and remove the engine mounting bolts, (1), on
both sides of the frame.
14. Carefully lift the engine from the frame.
15. Attach the engine to a suitable engine stand.
16. With the engine securely attached to the engine stand,
remove the chain sling from the two engine hoist eyes.
20002365N 6
Next operation:
Engine - Install (10.001)
48080062 10/11/2016
10.1 [10.001] / 14
19. Engine - Engine and crankcase
Engine - Install
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
Prior operation:
Engine - Remove Separating the tractor at the engine/frame (10.001)
1. Attach a chain sling to the two hoist eyes on the engine.
2. Attach a suitable hoist to the chain sling and raise the
hoist enough to support the engine.
3. Remove the engine from the engine stand.
4. Using the hoist, position the engine in the frame, align-
ing the mounting holes in the frame with the mounting
holes in the engine.
5. Install the engine mounting bolts, (1), on both sides of
the frame. Tighten the mounting bolts to 139 - 175 N·m
(103 - 129 lb ft) .
6. With the engine securely installed into the frame, re-
move the chain sling from the two engine hoist eyes.
20002365N 1
7. Install the firewall, (1), and the air cleaner mounting
bracket, (2), onto the engine.
76083812N 2
48080062 10/11/2016
10.1 [10.001] / 15
20. Engine - Engine and crankcase
8. Install the muffler, (1), onto the exhaust manifold, and
attach the exhaust pipe, (2), onto the muffler.
76083814N 3
9. Install the radiator, (1), and the oil cooler (if equipped)
onto the tractor frame.
10. Install the top, (2), and bottom, (3), radiator hoses.
11. Fill the radiator with new coolant to the proper level.
12. Install the muffler guard, (4), on the tractor.
30996394N 4
13. Install the air cleaner assembly, (1), on the firewall, (2),
and connect the air inlet hose to the air inlet manifold
pipe.
76083813N 5
48080062 10/11/2016
10.1 [10.001] / 16
21. Engine - Engine and crankcase
14. Connect the power steering tubes, (1), to the power
steering control motor, (2), the frame, (3), and the
power steering pump, (4).
76075732N 6
48080062 10/11/2016
10.1 [10.001] / 17
22. Engine - Engine and crankcase
Engine - Install Attaching the front transmission box to the engine
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
NOTICE: Do not use the buckle-up bolts to draw the drive
train together with the engine. Severe damage to the drive
train may result.
1. Attach a chain sling, (1), to the two hoist eyes, (2) and
(3), on the engine.
76075738N 1
2. Attach a suitable hoist, (1), to the chain sling, (2).
3. Carefully roll the drive train into alignment with the en-
gine. Align the splines on the front trans- mission box
input shaft with the engine flywheel. Rotate the engine
fan to align the input shaft and the flywheel. The floor
jack or the hoist may need to be raised or lowered to
make alignment possible.
76083809N 2
4. Connect the drive train, (1), to the engine, (2), and in-
stall the buckle-up bolts, (3). Tighten the buckle- up
bolts in a criss-cross pattern. Torque the M10 bolts and
nuts to 43 - 55 N·m (32 - 41 lb ft). Torque the two M12
bolts to 81 N·m (60 lb ft) .
76083811N 3
48080062 10/11/2016
10.1 [10.001] / 18
23. Engine - Engine and crankcase
5. Remove the chain hoist, (1), and the sling, (2), from
the engine hoist eyes.Remove the floor jack from the
tractor.
76083809N 4
6. Connect the fuel supply line, (1), to the fuel shutoff/filter,
(2), and connect the fuel tank vent line, (3), to the tee
fitting.
76075737 5
7. Attach the firewall support, (1), to the firewall, (2), and
the front transmission box, (3). Secure with the retain-
ing bolts.
76083815N 6
48080062 10/11/2016
10.1 [10.001] / 19
24. Engine - Engine and crankcase
8. If equipped, Install the FWD driveshaft, (1), and secure
with the two roll pins, (2).
20000904N 7
9. Install the starter, (1), onto the engine, and secure with
the retaining nuts. Connect the wires, (2), to the starter,
(1).
30997565N 8
48080062 10/11/2016
10.1 [10.001] / 20
25. Engine - Engine and crankcase
10. Install the hydraulic system pressure tube, (1), on the
hydraulic pump, (2), and the diverter valve.
11. Install the hydraulic system inlet tube, (3), onto the
hydraulic pump, (2), and connect the power steering
return hose, (4), to the inlet tube, (3).
76075731N 9
NOTE: Reattach the tractor cab and hood at this time. To
accomplish this, see “Platform” Section 90, for installation
procedure.
12. If the engine oil was drained, and the oil filter was
removed during disassembly, install a new oil filter on
the engine, and fill the engine with the recommended
oil to the proper level.
13. Connect the positive (+), (1), and the negative (-), (2),
battery cables to the battery.
14. Check the fluid levels and start the tractor. Check for
leaks and proper operation of all systems.
15. Make any adjustments necessary for proper operation
of the tractor.
76083810N 10
48080062 10/11/2016
10.1 [10.001] / 21
26. Engine - Engine and crankcase
Crankcase - Inspect
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
Prior operation:
Cylinder head - Assemble (10.101).
1. Inspect the cylinder block top face for cracks, dam-
age, and warping in the same way as for the cylinder
head. Replace the cylinder block if warp is greater than
0.12 mm (0.005 in).
2. Visually inspect the cylinder bore. There should be no
scoring, rust, or corrosion.
3. Using a telescoping gauge in line with the crankshaft,
measure the inside diameter of the top of the bore (ap-
proximately 15 mm (0.59 in) below the top of the block)
on all models.
4. Repeat this measurement at right angles to the crank-
shaft at the same distance.
5. In line with the crankshaft at the bottom of the bore,
measure (approximately 117 mm (4.6 in) Model ISM
N844, and 127 mm (5 in) Model ISM N844L) from the
top of the cylinder.
20093380 1
6. Repeat this measurement at right angles to the crank-
shaft at the same distance.
7. If any of the measurements taken indicate worn or dam-
aged cylinder bores, replace engine block with a long
block assembly.
NOTE: If the cylinder bore measures 84.2 mm (3.315 in)
long replace the block assembly.
Next operation:
Connecting rod and piston - Inspect (Piston) (10.105).
48080062 10/11/2016
10.1 [10.001] / 22
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Engine - Cylinder heads
Cylinder head - Static description
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
Cylinder Head and Valve Train Components
The cylinder head incorporates the valve assemblies, rocker arms, rocker shaft, push rods, and lifters. A swirl cham-
ber located between the injector assembly and the main combustion chamber of the cylinders provides improved
starting and greater fuel efficiency. Initial combustion starts in the precombustion chamber and as the expansion oc-
curs a strong swirl pattern is created in the main combustion chamber for more complete combustion of the air-fuel
mixture. The air intake manifold is separate from the cast aluminum valve cover on all these engines. The exhaust
manifold is bolted on the left-hand side of the cylinder head on each of the models. Cylinder heads have integral valve
guides. Standard size valves only are used.
The cylinder block assembly contains the pistons, connecting rods, crankshaft, timing gears, and engine oil pump.
The crankshaft is supported on five main bearings. The front bearing is positioned in a bore in front of the block. The
other bearings are split liners located in holders bolted to the block. The camshaft is supported on four ball bearings
located in the block.
7607624950 1
Engine models ISM N844 and ISM N844L
48080062 10/11/2016
10.2 [10.101] / 4
29. Engine - Cylinder heads
Valve cover - Install
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
Prior operation:
Valve drive and gears - Clearance (Valves) (10.106).
1. Install a new gasket (1) and position the valve cover (2)
over the rocker arms.
2. Install the valve cover retaining bolts (3), and tighten to
12 - 16 N·m (9 - 19 lb ft).
3. Install and tighten the seal washer (4), and cap nuts (5).
76075733A 1
Next operation:
Water pump - Install (with Cooling Fan) (10.400).
48080062 10/11/2016
10.2 [10.101] / 5
30. Engine - Cylinder heads
Cylinder head - Compression test
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
Compression test is performed through the glow plug ports. The test adapter tool (1), is equipped with quick coupler
ends for easy installation of the hose and gauge.
The procedures to perform a compression test are as follows:
1. Remove the wire lead from the fuel injection pump so-
lenoid.
2. Remove the glow plug electrical wire and wire connec-
tor from top of the glow plugs.
SECT10C01PG17_1 1
3. Remove all of the glow plugs.
NOTE: Be sure all the glow plugs are removed before starting the compression tests.
4. Install the adapter Tool No. FNH00120 , hose and
gauge assembly OEM1074 (2), in each port and crank
the engine until pressure stabilizes. The gauge should
read 2944 kPa (427 psi) ) plus or minus 345 kPa
(50 psi) .
SECT10C01PG17_2 2
NOTE: It may be necessary to remove some injector fuel lines to install the adapter tool.
NOTE: There should not be more than 345 kPa (50 psi) variation between the cylinders.
5. When all cylinders have been tested, reinstall the glow
plugs and electrical connections.
48080062 10/11/2016
10.2 [10.101] / 6
31. Engine - Cylinder heads
Cylinder head - Remove
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
Prior operation:
Rocker Arm Shaft and Support Bracket - Remove; See: “Engine Disassemble”..
1. Remove the valve stem caps (1), and push rods (2).
2. To remove the cylinder head, remove the cylinder head
bolts (3), by alternately loosening a half turn at a time
to prevent warping the head.
NOTE: Keep all valve components in separately marked
containers for reassembly in their original location.
20093361A 1
Next operation:
Valve Tappet - Removal; See: “Engine Disassemble”.
48080062 10/11/2016
10.2 [10.101] / 7
32. Engine - Cylinder heads
Cylinder head - Inspect
Farmall® 40B CVT NA
Farmall® 45B CVT NA
Farmall® 50B CVT NA
Prior operation:
Crankcase gears - Remove - with Camshaft (10.114).
1. Disassembly
1. Clean the cylinder head and remove any carbon
deposits from around the valve heads.
2. Use a valve spring compressor and remove the
valve spring retainer locks (1), spring (2), and
spring retainer (3), from each valve (4).
3. Remove the valves and place the valve compo-
nents together in separately marked containers for
reassembly in their original position.
20093369 1
2. Inspection and Repair
1. Clean all carbon deposits from the combustion
chamber and valve ports using a wire brush and
scraper.
2. Clean all dirt and residue from the gasket surface
using care not to scratch or nick the machined sur-
face.
3. Clean the cylinder head in solvent and air dry.
4. Inspect the head for cracks or damage in the fol-
lowing areas:
• Valve ports
• Valve seats (2).
• Prechamber (3).
• External cracks in the water jackets (1)..
5. Inspect the gasket surfaces for scratches or nicks,
which could cause leakage.
6. Examine the core hole plugs for rust or signs of
leakage. If a plug shows signs of damaging rust or
leakage, replace all plugs in the head.
7. Inspect the prechamber for carbon deposits and
looseness. Remove any carbon deposits found.
If prechamber is found to be loose, cylinder head
may be warped.
20093370 2
48080062 10/11/2016
10.2 [10.101] / 8