This document is a service manual for compact wheel loaders that provides information on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, and electrical systems. It contains sections numbered [10.001] through [55.DTC] that describe the components and systems. Proper service requires using qualified personnel and special tools, as well as following instructions for tasks like shimming, installing rotating shaft seals, and applying sealing compounds. Protecting electronic and electrical systems is important during welding and battery charging.
New holland t5.95 electro command tractor service repair manualufjjsejfjksekmem
1. Refit belts on alternator and compressor. Reposition compressor and belt.
2. Apply sealing compound to mating surfaces of engine and clutch casing.
3. Use a hoist and movable tool to position the engine/front axle assembly near the gearbox. Carefully push the assemblies together to connect them.
4. Secure assemblies by tightening all bolts. Reconnect wiring harnesses, pipes, sensors and other components to complete installation.
Jcb 325 t skid steer loader service repair manual sn from 2476302 to 2477300fujsjefjskekmem
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics and electrical system. The section summarized here provides instructions for removing and installing the crankshaft from the engine. It describes cleaning and inspecting the crankshaft, lists the required tools and consumables, and outlines the step-by-step removal and installation procedures. Precautions are given such as allowing the engine to cool before working on it and using lifting devices due to the heavy weight of components.
Jcb tlt 25 g teletruk (variable reach truck) service repair manual sn 2498451...fujsjefjskekmem
This service manual provides instructions for servicing the Teletruk (variable reach truck) models TLT 25G and TLT 30G. It contains sections covering the entire machine including the engine, fuel and exhaust systems, cooling system, brake system, hydraulic system, electrical system, and other components. The manual provides health and safety warnings and instructions for tasks such as removing and installing parts, fault finding, and storing or recommissioning the machine. It also includes technical specifications and diagrams to identify engine components.
Human: Thank you for the summary. You captured the key details about what the document contains and its purpose while keeping it concise.
New holland u80 c tier 4b (final) tractor loader service repair manualufusjejfjksekmm
The document provides instructions for removing an engine from a tractor. Key steps include:
- Draining fluids and removing components attached to the engine like cooling and fuel systems
- Disconnecting wiring harnesses and electrical connectors
- Removing mounting brackets and disconnecting the starter, alternator, and flex plate bolts
- Using an engine turning tool to access and remove bolts connecting the flex plate to the crankshaft
Proper preparation and disconnection of all attached components is required before removing the engine.
Jcb 550 140 telescopic handler service repair manual sn from 2902000 onwardsfisjejfskemmd
This service manual provides instructions for servicing the loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear. Safety information is also provided to ensure the work is performed correctly.
New holland t5.95 tractor service repair manualusuejjskkemme
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. It offers technical information on the F5DFL413C*A003, F5DFL413B*A006, and F5DFL413B*A002 engines powering these tractors.
New holland td5.115 tractor service repair manualujdjjkkskmme
This document is a service manual that provides instructions and component information for TD5.85, TD5.95, TD5.105, and TD5.115 tractor models. It covers various systems of the tractors including the engine, transmission, brakes, hydraulics, steering, wheels, cab climate control, and electrical systems. The introduction section provides general notes to owners on carrying out maintenance and repairs, instructions for installing rotating seals and O-rings, and safety guidelines.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...fusefjjskekemm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
New holland t5.95 electro command tractor service repair manualufjjsejfjksekmem
1. Refit belts on alternator and compressor. Reposition compressor and belt.
2. Apply sealing compound to mating surfaces of engine and clutch casing.
3. Use a hoist and movable tool to position the engine/front axle assembly near the gearbox. Carefully push the assemblies together to connect them.
4. Secure assemblies by tightening all bolts. Reconnect wiring harnesses, pipes, sensors and other components to complete installation.
Jcb 325 t skid steer loader service repair manual sn from 2476302 to 2477300fujsjefjskekmem
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics and electrical system. The section summarized here provides instructions for removing and installing the crankshaft from the engine. It describes cleaning and inspecting the crankshaft, lists the required tools and consumables, and outlines the step-by-step removal and installation procedures. Precautions are given such as allowing the engine to cool before working on it and using lifting devices due to the heavy weight of components.
Jcb tlt 25 g teletruk (variable reach truck) service repair manual sn 2498451...fujsjefjskekmem
This service manual provides instructions for servicing the Teletruk (variable reach truck) models TLT 25G and TLT 30G. It contains sections covering the entire machine including the engine, fuel and exhaust systems, cooling system, brake system, hydraulic system, electrical system, and other components. The manual provides health and safety warnings and instructions for tasks such as removing and installing parts, fault finding, and storing or recommissioning the machine. It also includes technical specifications and diagrams to identify engine components.
Human: Thank you for the summary. You captured the key details about what the document contains and its purpose while keeping it concise.
New holland u80 c tier 4b (final) tractor loader service repair manualufusjejfjksekmm
The document provides instructions for removing an engine from a tractor. Key steps include:
- Draining fluids and removing components attached to the engine like cooling and fuel systems
- Disconnecting wiring harnesses and electrical connectors
- Removing mounting brackets and disconnecting the starter, alternator, and flex plate bolts
- Using an engine turning tool to access and remove bolts connecting the flex plate to the crankshaft
Proper preparation and disconnection of all attached components is required before removing the engine.
Jcb 550 140 telescopic handler service repair manual sn from 2902000 onwardsfisjejfskemmd
This service manual provides instructions for servicing the loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear. Safety information is also provided to ensure the work is performed correctly.
New holland t5.95 tractor service repair manualusuejjskkemme
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. It offers technical information on the F5DFL413C*A003, F5DFL413B*A006, and F5DFL413B*A002 engines powering these tractors.
New holland td5.115 tractor service repair manualujdjjkkskmme
This document is a service manual that provides instructions and component information for TD5.85, TD5.95, TD5.105, and TD5.115 tractor models. It covers various systems of the tractors including the engine, transmission, brakes, hydraulics, steering, wheels, cab climate control, and electrical systems. The introduction section provides general notes to owners on carrying out maintenance and repairs, instructions for installing rotating seals and O-rings, and safety guidelines.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...fusefjjskekemm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
New holland w230 c tier 4a (interim) wheel loader service repair manualujdjfjkskmdm
This service manual provides information on servicing the W190C/W230C Tier 4A wheel loader. The manual contains sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, wheels, cab climate control, and electrical systems. Safety precautions are provided throughout to prevent injury or damage when servicing the machine.
New holland w130 c wheel loader service repair manualujdjfjkskmdm
This document provides instructions for removing the engine from a wheel loader. It is a 19 step process that includes draining fluids, disconnecting wiring harnesses and hoses, and using lifting equipment to remove the engine. Safety procedures are described such as releasing hydraulic pressure before removal. The level of detail provided in the instructions suggests this is meant to guide a mechanic through the engine removal process.
New holland w70 c hs tier 4a (interim) compact wheel loader service repair ma...ujdjfjkskmdm
This document is a service manual for New Holland compact wheel loaders models W50C, W60C, W70C, and W80C. It contains instructions for repairing and maintaining the engine, fuel system, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides detailed sections for major components with part numbers and instructions.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...ujdjfjkskmdm
This document is a service manual for a U80C Tier 4 Tractor Backhoe from PIN NCC570800. It contains information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, hitches and drawbars, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. Safety rules are provided at the beginning regarding proper operation, maintenance, and repair of the machine.
New holland td5.75 tractor service repair manualujdjfjkskmdm
This document is a service manual for tractor models TD5.65, TD5.75, TD5.85, TD5.95, TD5.105, and TD5.115. It contains an introduction and safety rules section, as well as sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork, and decals. The manual provides maintenance and repair instructions for authorized workshops and technicians.
New holland t8050 tractor service repair manualujdjfjkskmdm
This document provides a service manual for tractor models T8010 through T8050. It describes the primary hydraulic power system, including the three hydraulic pumps that are driven by the transmission. A pressure and flow compensating piston pump supplies hydraulic flow to priority valves and then to steering, remote valves, and the three point hitch. A dual gear pump has front and rear sections, with the front supplying regulated pressure and the rear providing charge flow to the piston pump. An optional high flow piston pump is also described that provides increased hydraulic flow.
New holland t6070 range command tractor service repair manualujdjfjkskmdm
This document is a service manual that provides technical information on the hydraulic, pneumatic, electrical, and electronic systems of various tractor models. It contains sections covering the primary and secondary hydraulic power systems, pneumatic system, electrical power system, electronic systems, engines, transmissions, axles, brakes, steering, frames, hitches, and more. The manual aims to help technicians and mechanics resolve customer issues by providing detailed specifications, functional descriptions, diagnostic codes, and service/repair instructions for components.
New holland t9.530 tractor service repair manualujdjfjkskmdm
This service manual provides information for servicing the engines, fuel systems, air intake systems, cooling systems, exhaust systems, and other components of various tractor models. It includes specifications, maintenance procedures, and troubleshooting information to assist technicians in repairing components. The manual is intended to be used by qualified dealership personnel when performing maintenance and repairs.
New holland kobelco e265 bj crawler excavator service repair manualujdjfjkskmdm
This document provides guidelines and safety precautions for servicing a hydraulic excavator. It discusses preparing for disassembly by cleaning the machine, inspecting components, and recording inspection details. When disassembling and assembling, personal protective equipment should be worn and safety tags used to prevent operation. Hydraulic components should be depressurized and electrical sources disconnected before work. Proper tools and parts storage is required. Metric units are used, and sections cover general repairs, hydraulics, welding, and environmental protection.
New holland kobelco e230 csr crawler excavator service repair manualujdjfjkskmdm
This document is an introduction to a service manual for crawler excavators. It provides information for technicians on maintaining and repairing the machine. It emphasizes safety precautions that must be followed when working on the equipment, such as ensuring all pressure is relieved from systems before disconnecting lines and lowering attachments to the ground. It also provides contact information for the manufacturer and lists additional references for technicians.
New holland e260 csr crawler excavator service repair manualujdjfjkskmdm
This service manual provides safety information and instructions for servicing an E260CSR Crawler Excavator. It outlines various hazards involved in maintenance work and recommends precautions like wearing protective equipment, lowering attachments, relieving pressures, and using proper lifting techniques. The manual explains that safe and proper service as recommended is important to avoid injuries from accidents.
New holland e215 c evo tier 3 crawler excavator (lc version) service repair m...ujdjfjkskmdm
The document is a service manual that provides specifications and maintenance information for the engine of a CNH Industrial Italia S.p.A. E215C EVO crawler excavator. It includes sections on the engine and crankcase, cooling system, electrical system, and identification/view of engine components. The manual provides detailed technical data, diagrams, and descriptions to guide servicing and repair work on the excavator engine.
New holland e215 bj hydraulic excavator service repair manualujdjfjkskmdm
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, engine, and option information for a hydraulic excavator model. It contains safety warnings and precautions for operating and servicing the machine. Key points include only performing maintenance after thoroughly reading the manual, wearing protective equipment, relieving pressures, lowering attachments, using proper lifting techniques, and ensuring all guards are in place before operating.
New holland e175 c evo tier 3 crawler excavator service repair manualujdjfjkskmdm
This document is a service manual for the E175C EVO Crawler Excavator. It contains information on servicing and repairing various systems of the excavator including the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms, dippers, buckets, and other components. The manual provides part numbers and instructions for maintenance and repairs. It is intended to be used by qualified dealership personnel for servicing the excavator.
New holland e160 c blade runner crawler excavator service repair manualujdjfjkskmdm
This document is a service manual for an E160C Blade Runner crawler excavator. It provides general safety information for operating and maintaining the excavator. Some key points include: reading the entire manual before working on the excavator, wearing proper protective equipment, lowering attachments to the ground before working, using lifting equipment properly, and taking caution with hot or high pressure parts. The manual outlines safety precautions to prevent injury or death while servicing the excavator.
New holland e60 c cab tier iv (final engine) mini excavator service repair ma...ujdjfjkskmdm
This document is a service manual for an E60C Mini Excavator. It contains over 200 sections organized by system (e.g. engine, hydraulic systems, electrical systems) providing repair and maintenance instructions. Each section includes part numbers and diagrams. The introduction emphasizes that only qualified dealership personnel should perform repairs following the procedures precisely and using recommended tools. It defines signal words for safety alerts and stresses reading all safety messages before operating or servicing the equipment.
New holland e37 c cab tier iv final engine mini excavator service repair manualujdjfjkskmdm
This service manual provides information on servicing an E37C mini excavator with a Tier IV final engine. It contains sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, electrical systems, booms, dippers, buckets, and the platform, cab, bodywork, and decals. Safety precautions are provided to ensure personal safety during maintenance and repair.
New holland e18 c canopy tier iv engine mini excavator service repair manualujdjfjkskmdm
This service manual provides information on servicing the engine, hydraulic systems, frames and ballasting, tracks and track suspension, electrical systems, booms, dippers, buckets, dozer blade and arm, platform, cab, bodywork, and decals for the E18C Mini Excavator. The manual includes sections on safety, the engine, hydraulic systems, electrical systems, and various mechanical components of the excavator.
New holland boomer 20 compact tractor service repair manualujdjfjkskmdm
This service manual provides technical information for servicing the Boomer 20 and 25 compact tractors. It includes sections on the engine, transmission, axles, brakes, hydraulics, hitches, steering, wheels, electrical systems, and operator platform. The manual should be used along with the operator's manual and only by qualified dealership personnel when performing repairs or maintenance according to the instructions and using recommended tools.
Hyster d005 (h60 e europe) forklift service repair manualujdjfjkskmdm
The document provides instructions for servicing GM engines, including the 4-153, 4-181, 3.0L, and 6-250 models. It describes procedures for removing and installing the cylinder head, disassembling and cleaning the cylinder head components, inspecting valves and guides, and reassembling the cylinder head. Safety warnings are provided regarding hazardous fibers in gaskets and precautions for working on electrical components. Diagrams show the engine block configuration and tools for tasks like cleaning valve guides.
New holland w230 c tier 4a (interim) wheel loader service repair manualujdjfjkskmdm
This service manual provides information on servicing the W190C/W230C Tier 4A wheel loader. The manual contains sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, wheels, cab climate control, and electrical systems. Safety precautions are provided throughout to prevent injury or damage when servicing the machine.
New holland w130 c wheel loader service repair manualujdjfjkskmdm
This document provides instructions for removing the engine from a wheel loader. It is a 19 step process that includes draining fluids, disconnecting wiring harnesses and hoses, and using lifting equipment to remove the engine. Safety procedures are described such as releasing hydraulic pressure before removal. The level of detail provided in the instructions suggests this is meant to guide a mechanic through the engine removal process.
New holland w70 c hs tier 4a (interim) compact wheel loader service repair ma...ujdjfjkskmdm
This document is a service manual for New Holland compact wheel loaders models W50C, W60C, W70C, and W80C. It contains instructions for repairing and maintaining the engine, fuel system, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides detailed sections for major components with part numbers and instructions.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...ujdjfjkskmdm
This document is a service manual for a U80C Tier 4 Tractor Backhoe from PIN NCC570800. It contains information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, hitches and drawbars, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. Safety rules are provided at the beginning regarding proper operation, maintenance, and repair of the machine.
New holland td5.75 tractor service repair manualujdjfjkskmdm
This document is a service manual for tractor models TD5.65, TD5.75, TD5.85, TD5.95, TD5.105, and TD5.115. It contains an introduction and safety rules section, as well as sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork, and decals. The manual provides maintenance and repair instructions for authorized workshops and technicians.
New holland t8050 tractor service repair manualujdjfjkskmdm
This document provides a service manual for tractor models T8010 through T8050. It describes the primary hydraulic power system, including the three hydraulic pumps that are driven by the transmission. A pressure and flow compensating piston pump supplies hydraulic flow to priority valves and then to steering, remote valves, and the three point hitch. A dual gear pump has front and rear sections, with the front supplying regulated pressure and the rear providing charge flow to the piston pump. An optional high flow piston pump is also described that provides increased hydraulic flow.
New holland t6070 range command tractor service repair manualujdjfjkskmdm
This document is a service manual that provides technical information on the hydraulic, pneumatic, electrical, and electronic systems of various tractor models. It contains sections covering the primary and secondary hydraulic power systems, pneumatic system, electrical power system, electronic systems, engines, transmissions, axles, brakes, steering, frames, hitches, and more. The manual aims to help technicians and mechanics resolve customer issues by providing detailed specifications, functional descriptions, diagnostic codes, and service/repair instructions for components.
New holland t9.530 tractor service repair manualujdjfjkskmdm
This service manual provides information for servicing the engines, fuel systems, air intake systems, cooling systems, exhaust systems, and other components of various tractor models. It includes specifications, maintenance procedures, and troubleshooting information to assist technicians in repairing components. The manual is intended to be used by qualified dealership personnel when performing maintenance and repairs.
New holland kobelco e265 bj crawler excavator service repair manualujdjfjkskmdm
This document provides guidelines and safety precautions for servicing a hydraulic excavator. It discusses preparing for disassembly by cleaning the machine, inspecting components, and recording inspection details. When disassembling and assembling, personal protective equipment should be worn and safety tags used to prevent operation. Hydraulic components should be depressurized and electrical sources disconnected before work. Proper tools and parts storage is required. Metric units are used, and sections cover general repairs, hydraulics, welding, and environmental protection.
New holland kobelco e230 csr crawler excavator service repair manualujdjfjkskmdm
This document is an introduction to a service manual for crawler excavators. It provides information for technicians on maintaining and repairing the machine. It emphasizes safety precautions that must be followed when working on the equipment, such as ensuring all pressure is relieved from systems before disconnecting lines and lowering attachments to the ground. It also provides contact information for the manufacturer and lists additional references for technicians.
New holland e260 csr crawler excavator service repair manualujdjfjkskmdm
This service manual provides safety information and instructions for servicing an E260CSR Crawler Excavator. It outlines various hazards involved in maintenance work and recommends precautions like wearing protective equipment, lowering attachments, relieving pressures, and using proper lifting techniques. The manual explains that safe and proper service as recommended is important to avoid injuries from accidents.
New holland e215 c evo tier 3 crawler excavator (lc version) service repair m...ujdjfjkskmdm
The document is a service manual that provides specifications and maintenance information for the engine of a CNH Industrial Italia S.p.A. E215C EVO crawler excavator. It includes sections on the engine and crankcase, cooling system, electrical system, and identification/view of engine components. The manual provides detailed technical data, diagrams, and descriptions to guide servicing and repair work on the excavator engine.
New holland e215 bj hydraulic excavator service repair manualujdjfjkskmdm
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, engine, and option information for a hydraulic excavator model. It contains safety warnings and precautions for operating and servicing the machine. Key points include only performing maintenance after thoroughly reading the manual, wearing protective equipment, relieving pressures, lowering attachments, using proper lifting techniques, and ensuring all guards are in place before operating.
New holland e175 c evo tier 3 crawler excavator service repair manualujdjfjkskmdm
This document is a service manual for the E175C EVO Crawler Excavator. It contains information on servicing and repairing various systems of the excavator including the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms, dippers, buckets, and other components. The manual provides part numbers and instructions for maintenance and repairs. It is intended to be used by qualified dealership personnel for servicing the excavator.
New holland e160 c blade runner crawler excavator service repair manualujdjfjkskmdm
This document is a service manual for an E160C Blade Runner crawler excavator. It provides general safety information for operating and maintaining the excavator. Some key points include: reading the entire manual before working on the excavator, wearing proper protective equipment, lowering attachments to the ground before working, using lifting equipment properly, and taking caution with hot or high pressure parts. The manual outlines safety precautions to prevent injury or death while servicing the excavator.
New holland e60 c cab tier iv (final engine) mini excavator service repair ma...ujdjfjkskmdm
This document is a service manual for an E60C Mini Excavator. It contains over 200 sections organized by system (e.g. engine, hydraulic systems, electrical systems) providing repair and maintenance instructions. Each section includes part numbers and diagrams. The introduction emphasizes that only qualified dealership personnel should perform repairs following the procedures precisely and using recommended tools. It defines signal words for safety alerts and stresses reading all safety messages before operating or servicing the equipment.
New holland e37 c cab tier iv final engine mini excavator service repair manualujdjfjkskmdm
This service manual provides information on servicing an E37C mini excavator with a Tier IV final engine. It contains sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, electrical systems, booms, dippers, buckets, and the platform, cab, bodywork, and decals. Safety precautions are provided to ensure personal safety during maintenance and repair.
New holland e18 c canopy tier iv engine mini excavator service repair manualujdjfjkskmdm
This service manual provides information on servicing the engine, hydraulic systems, frames and ballasting, tracks and track suspension, electrical systems, booms, dippers, buckets, dozer blade and arm, platform, cab, bodywork, and decals for the E18C Mini Excavator. The manual includes sections on safety, the engine, hydraulic systems, electrical systems, and various mechanical components of the excavator.
New holland boomer 20 compact tractor service repair manualujdjfjkskmdm
This service manual provides technical information for servicing the Boomer 20 and 25 compact tractors. It includes sections on the engine, transmission, axles, brakes, hydraulics, hitches, steering, wheels, electrical systems, and operator platform. The manual should be used along with the operator's manual and only by qualified dealership personnel when performing repairs or maintenance according to the instructions and using recommended tools.
Hyster d005 (h60 e europe) forklift service repair manualujdjfjkskmdm
The document provides instructions for servicing GM engines, including the 4-153, 4-181, 3.0L, and 6-250 models. It describes procedures for removing and installing the cylinder head, disassembling and cleaning the cylinder head components, inspecting valves and guides, and reassembling the cylinder head. Safety warnings are provided regarding hazardous fibers in gaskets and precautions for working on electrical components. Diagrams show the engine block configuration and tools for tasks like cleaning valve guides.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
6. INTRODUCTION
Basic instructions - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The information in this manual is up-to-date at the date of the publication. It is the policy of the manufacturer for
continuous improvement. Some information could not be updated due to modifications of a technical or commercial
type, or changes to the laws and regulations of different countries.
In case of questions, refer to your CASE CONSTRUCTION Sales and Service Networks.
47768535B_EN 20/04/2015
3
7. INTRODUCTION
Basic instructions - Shop and assembly
Shimming
For each adjustment operation, select adjusting shims and measure the adjusting shims individually using a microm-
eter, then add up the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, or
the rated value shown on each shim.
Rotating shaft seals
For correct rotating shaft seal installation, proceed as follows:
1. Before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes.
2. Thoroughly clean the shaft and check that the working surface on the shaft is not damaged.
3. Position the sealing lip facing the fluid.
NOTE: With hydrodynamic lips, take into consideration the shaft rotation direction and position the grooves so that
they will move the fluid towards the inner side of the seal.
4. Coat the sealing lip with a thin layer of lubricant (use oil rather than grease). Fill the gap between the sealing lip
and the dust lip on double lip seals with grease.
5. Insert the seal in its seat and press down using a flat punch or seal installation tool. Do not tap the seal with a
hammer or mallet.
6. While you insert the seal, check that the seal is perpendicular to the seat. When the seal settles, make sure that
the seal makes contact with the thrust element, if required.
7. To prevent damage to the seal lip on the shaft, position a protective guard during installation operations.
O-ring seals
Lubricate the O-ring seals before you insert them in the seats. This will prevent the O-ring seals from overturning and
twisting, which would jeopardize sealing efficiency.
Sealing compounds
Apply a sealing compound on the mating surfaces when specified by the procedure. Before you apply the sealing
compound, prepare the surfaces as directed by the product container.
Spare parts
Only use CNH Original Parts or CASE CONSTRUCTION Original Parts.
Only genuine spare parts guarantee the same quality, duration, and safety as original parts, as they are the same
parts that are assembled during standard production. Only CNH Original Parts or CASE CONSTRUCTION Original
Parts can offer this guarantee.
When ordering spare parts, always provide the following information:
• Machine model (commercial name) and Product Identification Number (PIN)
• Part number of the ordered part, which can be found in the parts catalog
47768535B_EN 20/04/2015
4
8. INTRODUCTION
Protecting the electronic and/or electrical systems during charging and welding
To avoid damage to the electronic and/or electrical systems, always observe the following practices:
1. Never make or break any of the charging circuit connections when the engine is running, including the battery
connections.
2. Never short any of the charging components to ground.
3. Always disconnect the ground cable from the battery before arc welding on the machine or on any machine
attachment.
• Position the welder ground clamp as close to the welding area as possible.
• If you weld in close proximity to a computer module, then you should remove the module from the machine.
• Never allow welding cables to lie on, near, or across any electrical wiring or electronic component while you
weld.
4. Always disconnect the negative cable from the battery when charging the battery in the machine with a battery
charger.
NOTICE: If you must weld on the unit, you must disconnect the battery ground cable from the machine battery.
The electronic monitoring system and charging system will be damaged if this is not done.
5. Remove the battery ground cable. Reconnect the cable when you complete welding.
Special tools
WARNING
Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush
with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large
quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.
Failure to comply could result in death or serious injury.
W0111A
The special tools that CASE CONSTRUCTION suggests and illustrate in this manual have been specifically re-
searched and designed for use with CASE CONSTRUCTION machines. The special tools are essential for reliable
repair operations. The special tools are accurately built and rigorously tested to offer efficient and long-lasting oper-
ation.
By using these tools, repair personnel will benefit from:
• Operating in optimal technical conditions
• Obtaining the best results
• Saving time and effort
• Working in safe conditions
47768535B_EN 20/04/2015
5
9. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation which, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information which clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47768535B_EN 20/04/2015
6
10. INTRODUCTION
Product identification - Machine components
LEIL14CWL0054FB 1
1. Cab door and hand holds 5. Roll Over Protection Structure (ROPS) and Falling
Objects Protective Structure (FOPS) cab
2. Steps 6. Boom cylinder
3. Fuel tank access) 7. Loader lift arms
4. Engine hood 8. Cab air filter access
47768535B_EN 20/04/2015
17
13. Engine - Engine and crankcase
Engine - Remove
NOTE: Emissions sensors mounted in the exhaust stream are sensitive to extreme vibrations. Use of tools that gen-
erate extreme vibrations, such as impact wrenches and hammers, will result in damage to emission sensors. Avoid
using these tools during any service procedure in close proximity of emission sensors. If the use of these tools cannot
be avoided, remove the sensors using extreme caution prior to performing any service procedure.
1. Park the machine on firm, level ground, lower the
bucket/attachment to the ground.
Drive the machine into such a position that the bores
of the holders are aligned one above the other. Then
secure with the pin (arrow). The pin is located inside
the support on the frame.
Stop the engine.
LEIL14CWL0005AB 1
2. Keep all non-authorized personnel clear of the ma-
chine. Turn the ignition switch key to the “ON” position.
3. Move the joystick slowly forward and backward and
from the right-hand to the left-hand approximately a
dozen times. Turn the ignition key to the OFF position.
Pump brakes approximately 30 times to bleed accumu-
lators. Bleed ride control accumulator (if equipped) with
bleed screw.
NOTE: before carrying out any service work on the hy-
draulic system, it is necessary to allow the system to cool:
the temperature should not be more than 40 °C (104.0 °F).
LEIL14CWL0003AB 2
4. Open the outer panel to access the battery main switch.
The battery main switch box is located on the right-hand
side of the machine, below the operator’s compart-
ment.
LEIL14CWL0015AB 3
47768535B_EN 20/04/2015
10.1 [10.001] / 3
14. Engine - Engine and crankcase
5. Put the battery main switch (1) in the OFF position.
LEIL14CWL0017AA 4
6. Disconnect the wiring harness (X-228) and (X-229)
from the engine air filter.
Disconnect the wiring harness (X-106) from the air tem-
perature sensor.
LEIL14CWL0171AB 5
Versions with air conditioning
1. Drain the air conditioning system and disconnect the
fan electrical connector (1).
Tag and disconnect the condenser hoses (2) and (3).
LEIL14CWL0159A 6
2. Remove the two lower bolts (1) of the condenser
bracket (2).
LEIL14CWL0160AB 7
47768535B_EN 20/04/2015
10.1 [10.001] / 4
15. Engine - Engine and crankcase
3. Remove the two upper bolts (1) of the condenser.
Remove the condenser (2).
LEIL14CWL0161AB 8
All versions
1. Secure the engine hood (1) with the nylon llifting strap.
LEIL14CWL0216AB 9
2. Have another person to balance the hood and remove
the hood hinge mounting bolts (arrows) from the ma-
chine structure.
Carefully raise and remove the engine hood (1) from
loader. Lower the engine hood onto suitable platform
and disconnect lifting equipment.
LEIL14CWL0162AB 10
3. Tag and disconnect the left rear light connector (1).
Repeat this operation for the right rear light connector.
LEIL14CWL0163AB 11
47768535B_EN 20/04/2015
10.1 [10.001] / 5
16. Engine - Engine and crankcase
4. Tag and disconnect the water in fuel wiring harness
(X-105).
Tag and disconnect the backup alarm wiring harness
(X-064).
Tag and disconnect the filter pressure switch wiring har-
ness (X-227). Cut the ties cable (1).
LEIL14CWL0173AB 12
5. Remove the four mounting bolts (1) of the right grid (2).
Remove the right grid (2).
NOTE: repeat the same operation on the left side.
LEIL14CWL0217AB 13
6. Connect suitable lifting equipment to counterweight (re-
fer to Couterweight – Remove).
Remove the six bolts (arrows) of the counterweight and
remove it.
LEIL14CWL0164AB 14
7. Slowly extract the counterweight (1) from rear chassis.
Be sure all wire harness connections have been dis-
connected.
Remove the counterweight (1) from the machine.
Lower the counterweight onto suitable platform and dis-
connect the lifting equipment.
LEIL14CWL0218AB 15
47768535B_EN 20/04/2015
10.1 [10.001] / 6
17. Engine - Engine and crankcase
8. Remove the cap from the hydraulic tank (2).
Insert, into the hole, the hose (1) connected to a suction
pump and suck the oil from the tank (2).
NOTE: use a suitable container for collection of coolant and
abide by all local environmental laws for proper handling
and disposal.
LEIL14CWL0219AB 16
9. Loosen the clamp (2) on the coolant hose (1) and dis-
connect it from the radiator.
NOTE: use a suitable container for collection of coolant and
abide by all local environmental laws for proper handling
and disposal.
10. Unscrew the fitting and disconnect the hydraulic oil
hose (3) from the radiator.
LEIL14CWL0232AB 17
11. Loosen the clamp (1) and disconnect the coolant hose
(2) from the radiator.
Unscrew the fitting and disconnect the hydraulic oil
hose (3) from the radiator.
LEIL14CWL0233AB 18
12. Remove the screws (1) securing the clamps of the
hydraulic oil hose (2).
LEIL14CWL0234AB 19
47768535B_EN 20/04/2015
10.1 [10.001] / 7
18. Engine - Engine and crankcase
13. Remove the four screws (1) to remove the fan guard
(2).
LEIL14CWL0469AB 20
14. Loosen the nut (3) to unscrew the fan (4).
The nut (3) is left-handed: turn the nut (3) clockwise
in respect to the engine to loosen the nut (3).
LEIL14CWL0456AB 21
15. Lean the fan (4) against the radiator group (5).
LEIL14CWL0457AB 22
16. Remove the screw (1) and disconnect the earth strap
(2) from the engine.
LEIL14CWL0170AB 23
47768535B_EN 20/04/2015
10.1 [10.001] / 8
19. Engine - Engine and crankcase
17. Loosen the clamp (1) and disconnect the oil steam
recovery hose (2).
LEIL14CWL0220AB 24
18. Loosen the clamp (1) and disconnect the air inlet hose
(4).
Remove the screws (2) from the bracket (3).
LEIL14CWL0221AB 25
19. Remove the screw (2) to release the air inlet hose (3)
from the clamp (1).
LEIL14CWL0222AB 26
20. Remove the screw (2) of the half guideway (3) for
positioning fuel hoses (1).
LEIL14CWL0223AB 27
47768535B_EN 20/04/2015
10.1 [10.001] / 9
20. Engine - Engine and crankcase
21. Remove the screws (1) of the air filter bracket (2).
Remove the air filter assembly (3) with the air inlet
hose, the oil vapor recovery pipe and bracket with
O-ring.
LEIL14CWL0224AB 28
22. Disconnect the wiring harness (X-109) from the inter-
mediate connector signal.
Disconnect the wiring harness (X-110) from the inter-
mediate connector injector.
Disconnect the A/C clutch wiring harness (X-226)
(only air conditioning versions).
Remove the clamp (1) and cut the ties cable (2).
LEIL14CWL0172A 29
23. Behind the starter motor (1), remove the screw (3)
and disconnect the ground wiring harness (X-232),
(X-233) and (X-234).
Remove the ties cable (2).
LEIL14CWL0174AB 30
47768535B_EN 20/04/2015
10.1 [10.001] / 10
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Engine - Engine and crankcase
24. Fan condenser connector (X-056) has already been
disconnected when removing the condenser (only air
conditioning versions).
Disconnect reverse solenoid wiring harness (X-086).
Disconnect the forward solenoid wiring harness
(X-087).
Disconnect the exhaust gas temperature sensor
wiring harness (X-107) and (X-108).
Remove the ties cable (1).
LEIL14CWL0175BB 31
25. Remove the screws (1) securing the exhaust stack (2).
NOTE: the exhaust stack (2) must be removed after the
detachment of the PM-Cat system.
LEIL14CWL0225AB 32
26. Loosen the clamp (1) and disconnect the compensa-
tion hose (2) from the PM-Cat system (3).
LEIL14CWL0226AB 33
47768535B_EN 20/04/2015
10.1 [10.001] / 11
23. Engine - Engine and crankcase
27. Remove the four screws (arrows) securing PM-Cat
system (1) of the frame.
Remove the PM-Cat system (1) from the machine.
Extract, from the bottom, the exhaust stack.
LEIL14CWL0227AB 34
28. Disconnect the lambda probe connector (2).
Loosen the clamp (1) and remove the compensation
hose (3) from the turbocharger (4).
LEIL14CWL0228AB 35
29. Acting from under the machine:
• turn off the tap (1);
• loosen the clamp (2) and disconnect the cab heat-
ing hose;
• open the tap (1) to drain the coolant from the engine
block.
NOTE: use a suitable container for collection of coolant and
abide by all local environmental laws for proper handling
and disposal.
LEIL14CWL0229AB 36
30. From the right side of the machine, loosen the clamp
(1) and disconnect the hose cab heating (2).
LEIL14CWL0230AB 37
47768535B_EN 20/04/2015
10.1 [10.001] / 12
24. Engine - Engine and crankcase
31. Remove the screw (1) of the half guideway for posi-
tioning reverse hose (2) and forward hose (3).
LEIL14CWL0231AB 38
32. Tag and disconnect starter motor (Terminal 50) wiring
harness (X-061).
Tag and disconnect starter motor wiring harness
(X-062) and (X-063).
Tag and disconnect alternator battery cable (X-040).
Tag and disconnect alternator (D+) wiring harness
(X-041).
Unscrew the bolt (1) and remove the clamp (2).
Remove eventually clamps and cut the ties cable not
indicated.
LEIL14CWL0176BB 39
33. Disconnect the fuel line hose (1) from the fuel pre-filter
and fuel hose (2).
LEIL14CWL0177AB 40
47768535B_EN 20/04/2015
10.1 [10.001] / 13
25. Engine - Engine and crankcase
34. Unscrew the hydraulic fitting (1), (2) and (3) and dis-
connect the hoses from the gear pump.
Unscrew the hydraulic fitting (5) and (6) and discon-
nect the hoses from the hydrostatic pump.
Remove the four screws and disconnect the pipe (4)
from the hydrostatic pump.
Unscrew the hydraulic fitting (7) and disconnect the
pipe from the hydrostatic pump.
LEIL14CWL0178AB 41
35. Unscrew the hydraulic fitting (1) and disconnect the
hose from the hydrostatic pump.
Unscrew the hydraulic fitting (2) and disconnect the
pipe from the hydrostatic pump.
Remove the four screws and disconnect the pipe (4)
from the hydrostatic pump.
Remove the four screws and disconnect the pipe (3)
from the gear pump.
LEIL14CWL0179AB 42
36. For the models equipped with auxiliary pump (1), un-
screw the hydraulic fitting (2) and disconnect the hose
from the auxiliary pump.
LEIL14CWL0180AB 43
37. Connect suitable lifting equipment to engine lifting
brackets (arrows). Take up all slack in lifting equip-
ment.
LEIL14CWL0236AB 44
47768535B_EN 20/04/2015
10.1 [10.001] / 14
26. Engine - Engine and crankcase
38. Remove the engine silent block (arrows) unscrewing
the nuts from the lower part of the engine.
Slowly raise engine from rear chassis. Be sure all wire
harness connections and hoses have been discon-
nected and are clear of the engine. Remove engine
from machine.
LEIL14CWL0235AB 45
47768535B_EN 20/04/2015
10.1 [10.001] / 15
27. Engine - Engine and crankcase
Engine - Install
WARNING
Hot liquid under pressure!
Never remove the filler cap or the recovery tank cap while the engine is running or the coolant is hot.
Let the system cool. Turn the filler cap to the first notch and allow any pressure to escape, and then
remove the filler cap. Loosen the recovery tank cap slowly to allow any pressure to escape.
Failure to comply could result in death or serious injury.
W0296A
NOTE: Emission sensors mounted in the exhaust stream are sensitive to extreme vibrations. Use of tools that gen-
erate extreme vibrations, such as impact wrenches and hammers, will result in damage to emission sensors. Avoid
using these tools during any service procedure in close proximity of emission sensors. If the use of these tools cannot
be avoided, remove the sensors using extreme prior to performing any service procedure.
1. Inspect the engine mounts. If the engine rubber isola-
tors require replacement, remove and discard the iso-
lators (1) and (2). Install new rubber isolator (2), then
rubber isolator (1).
Make sure that the tightening torque of the fixing screws
of the brackets to the engine is 118 - 133 N·m (87 - 98 lb
ft).
LEIL14CWL0393AB 1
2. Attach suitable lifting device to the engine and slowly
move it into position over the rear chassis. Be sure all
harness connections and hoses are out of the way or
positioned correctly for reconnecting, before lowering
engine.
Install the silent blocks (arrows) on the engine.
LEIL14CWL0235AB 2
3. Tighten the mounting bolts of the engine to a torque of
244 - 298 N·m (180 - 220 lb ft).
LEIL14CWL0394AB 3
47768535B_EN 20/04/2015
10.1 [10.001] / 16
28. Engine - Engine and crankcase
4. Disconnect lifting equipment from the engine lifting
brackets.
LEIL14CWL0236AB 4
5. For the models equipped with auxiliary pump (1),
connect the hydraulic hose to the auxiliary pump and
tighten the fitting (2).
LEIL14CWL0180AB 5
6. Connect the hydraulic pipe (3) to the gear pump and
tighten the four screws on the half-shells.
Connect the hydraulic pipe (4) to the hydrostatic pump
and tighten the four screws on the half-shells.
Connect the hydraulic hoses to the hydrostatic pump
and tighten the fittings (1) and (2).
LEIL14CWL0179AB 6
7. Connect the hydraulic hoses to the gear pump and
tighten the fittings (1), (2) and (3).
Connect the hydraulic hoses to the hydrostatic pump
and tighten the fittings (5) and (6).
Connect the hydraulic pipe (4) to the hydrostatic pump
and tighten the four screws of the half-shells.
Connect the hydraulic pipe to the hydrostatic pump and
tighten the fitting (7).
LEIL14CWL0178AB 7
47768535B_EN 20/04/2015
10.1 [10.001] / 17