This document provides disassembly instructions for the transmission of a 621H wheel tractor. It outlines 48 steps to fully disassemble the transmission components. These include removing the transmission from the housing, separating the clutch housings and carrier assembly, and dismantling the individual planetary gear sets, shafts, rings, and plates. Detailed illustrations accompany each step to show the specific components and fasteners. Safety warnings are included where parts under spring tension could pose injury risks. Required tools are listed.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 621H WHEEL TRACTOR NYY
Configuration: 621H OEM Wheel Tractor NYY00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
621H, 623H and 627H
Wheel Tractor-Scrapers Power Train
Media Number -KENR9488-01 Publication Date -01/06/2013 Date Updated -01/07/2013
i04577911
Transmission Planetary - Disassemble - Tractor
SMCS - 3030-015
Disassembly Procedure
Start By:
A. Separate the transfer gears from the transmission.
B. Remove the transmission hydraulic control valve.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-7407 Eyebolt 2
B FT-0833 Clamp 2
C 2P-8312 Retaining Ring Pliers 1
D FT-1335 Transmission Fixture 1
E 1P-0520 Driver Gp 1
F 1P-2420 Transmission Repair Stand 2
G 1P-7405 Eyebolt 2
H 3/8 -16 by 2 in Forcing Bolts 4
1/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g02607496
1. Install Tooling (A) and a suitable lifting device onto transmission assembly (1) . Position
transmission assembly (1) onto Tooling (F) . The weight of transmission assembly (1) is
approximately 703 kg (1550 lb).
Illustration 2 g00841452
2. Remove bolts (2) and the washers that secure the transmission assembly to transmission
housing (3) . Remove the transmission assembly from transmission housing (3) . Position
the transmission assembly onto two suitable blocks. Remove Tooling (A) .
2/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00506814
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove bolts (4) and the washers from clutch housing (5) .
Illustration 4 g01083235
4. Use Tooling (B) in order to hold the piston into clutch housing (5) . Install Tooling (A) and
a suitable lifting device onto clutch housing (5) . Remove clutch housing (5) from the
transmission assembly. The weight of clutch housing (5) is approximately 27 kg (60 lb).
Remove Tooling (A) and (B) .
3/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g00506820
5. Remove piston (6) from clutch housing (5) . Remove seal ring (7) from piston (6) and from
clutch housing (5) .
Illustration 6 g01083237
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: Friction discs and clutch plates that are removed from each clutch housing should be
kept with the correct clutch housing. Mixing the clutch plates and friction discs may cause
improper operation of the transmission or damage to the transmission.
4/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. 6. Remove springs (8) , dowels (9) , friction discs (10) , and clutch plates (11) from clutch
housing (12) .
Illustration 7 g00506849
7. Remove ring gear (13) from clutch housing (12) .
Illustration 8 g01083343
8. Use Tooling (B) in order to hold the piston into clutch housing (12) . Install Tooling (A) and
a suitable lifting device onto clutch housing (12) . Remove clutch housing (12) from
housing assembly (14) . The weight of clutch housing (23) is approximately 27 kg (60 lb).
Remove Tooling (A) and (B) .
5/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 9 g00506903
9. Remove piston (15) from clutch housing (12) . Remove a seal ring (16) from piston (15) and
from clutch housing (12) .
Illustration 10 g01083344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Remove springs (17) , dowels (18) , friction discs (19) , and clutch plates (20) from housing
assembly (14) .
6/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 11 g02607597
Illustration 12 g00506953
11. Remove retaining ring (21A) and adapter drive (22A) . Remove retaining ring (21) from
shaft (22) .
Illustration 13 g01083360
7/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 12. Install Tooling (G) and a suitable lifting device onto carrier assembly (23) . Remove carrier
assembly (23) from housing assembly (14) . Remove Tooling (G) . The weight of the carrier
assembly is approximately 34 kg (75 lb).
Illustration 14 g00506968
13. Remove bolts (24) and oil slinger (25) from carrier assembly (23) . Remove bearing (26)
from carrier assembly (23) .
Illustration 15 g01053892
14. Use a hammer and a punch in order to push pin (27) into shaft (28) .
8/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 16 g01083400
15. Remove shaft (28) , thrust discs 29, and () planetary gears (30) from carrier assembly (23) .
Remove pin (27) from shaft (28) .
Illustration 17 g01053896
16. Remove bearings (31) from planetary gear (30) .
17. Repeat Steps 14, 15, and 16 in order to remove the remaining three shaft assemblies.
9/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 18 g01053901
18. Use a hammer and a punch in order to push pin (32) into shaft (33) .
Illustration 19 g01083401
19. Remove shaft (33) , thrust discs 34, and () gear (35) from carrier assembly (23) . Remove
tube (36) from shaft (33) . Remove pin (32) from shaft (33) .
Illustration 20 g00507145
20. Remove bearings (37) and spacer (38) from gear (35) .
21. Repeat Steps 18, 19, and 20 in order to remove the remaining three shaft assemblies from
the carrier assembly.
10/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 21 g01083402
22. Remove bolts (39) and plates (40) from clutch housing (41) . Remove ring gear (42) from
clutch housing (41) .
Illustration 22 g00507153
23. Remove bolts (43) that secure clutch housing (41) to housing assembly (14) .
Illustration 23 g01083403
11/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 24. Use Tooling (B) in order to hold the piston into clutch housing (41) . Install Tooling (A) and
a suitable lifting device onto clutch housing (41) . Remove clutch housing (41) from
housing assembly (14) . The weight of clutch housing (41) is approximately 27 kg (60 lb).
Remove Tooling (A) and (B) .
Illustration 24 g00507166
25. Remove piston (44) from clutch housing (41) . Remove seal ring (45) from piston (44) and
from clutch housing (41) .
Illustration 25 g00507206
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 26. Remove springs (46) , friction discs (47) , and clutch plate (48) from housing assembly
(14) .
Illustration 26 g00507207
27. Remove ring gear (49) from housing assembly (14) . Remove plate assembly (50) from
housing assembly (14) .
Illustration 27 g00507245
28. Remove retaining ring (51) from shaft (22) . Remove sun gear (52) and sun gear (53) from
shaft (22) .
13/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 28 g00507350
29. Remove bolts (54) and the washers in order to remove carrier assembly (55) from housing
assembly (14) .
Illustration 29 g01083405
30. Install Tooling (G) and a suitable lifting device onto carrier assembly (55) . Remove carrier
assembly (55) from housing assembly (14) . The weight of carrier assembly (55) is
approximately 14 kg (30 lb). Remove Tooling (G) .
14/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 30 g01053911
31. Use a hammer and a punch in order to push pin (56) into shaft (57) .
Illustration 31 g00507391
32. Remove shaft (57) , two thrust discs (58) , and gear (59) from carrier assembly (55) .
Remove pin (56) from shaft (57) .
Illustration 32 g00507395
33. Remove bearing (60) from gear (59) .
34. Follow Steps 31, 32, and 33 in order to remove the remaining two shaft assemblies from the
carrier assembly.
15/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 33 g01083407
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
35. Remove springs (61) , spring assemblies (62) , friction discs (63) , and clutch plate (64)
from housing assembly (65) . Remove reaction dowels (66) from housing assembly (65) .
Illustration 34 g01053916
16/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
36. Remove spring assemblies (67) and lock plates (68) from housing assembly (65) .
Illustration 35 g01083410
37. Remove coupling (69) and gear (70) as one unit from housing assembly (65) .
Illustration 36 g00507701
38. Remove seal rings (71) from gear (70) .
17/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 37 g00507724
39. Remove piston (72) from housing assembly (65) . Remove seal ring (73) from piston (72) .
Illustration 38 g00509609
40. Use Tooling (C) in order to remove retaining ring (74) from shaft (22) .
Illustration 39 g01083413
18/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 41. Remove metal seal ring (75) and retaining ring (76) from shaft (22) . Remove shaft (22)
from housing assembly (14) .
Illustration 40 g01083414
42. Install two Tooling (G) and a suitable lifting device onto housing assembly (65) . Remove
housing assembly (65) and balance piston (77) as one unit from housing assembly (14) .
Remove Tooling (G) .
Illustration 41 g00509681
43. Separate balance piston (77) from housing assembly (65) . Remove O-ring seal (78) from
housing assembly (65) .
19/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 42 g01053932
44. Remove seal ring (79) from housing assembly (65) . Remove retaining ring (80) and bearing
(81) from housing assembly (65) .
Illustration 43 g00509719
45. Use a suitable lifting device in order to turn over the housing assembly. Position the housing
assembly onto suitable blocks, as shown. The weight of housing assembly (84) is
approximately 61 kg (135 lb). Remove bolts (82) and the washers that secure clutch housing
(83) to manifold (84) .
Note: Manifold (84) is a component of housing assembly (14) . Previous text refers to
manifold (84) and housing assembly (14) as identical components.
20/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 44 g01083437
46. Use Tooling (B) to secure the clutch piston to clutch housing (83) . Install Tooling (A) and a
suitable lifting device to clutch housing (83) . Remove clutch housing (83) from manifold
(84) . The weight of clutch housing (83) is approximately 14 kg (30 lb). Remove Tooling
(A) and Tooling (B) .
Illustration 45 g00515858
47. Remove clutch piston (85) from the clutch housing. Remove seal rings (86) from clutch
piston (85) .
21/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 46 g02607680
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
48. Remove reaction dowels (87) , springs (88) , friction discs (89) , and clutch plates (90) from
manifold (84) .
Note: Be aware of location of springs for assembly purposes.
Illustration 47 g00515860
22/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 48 g01083470
49. Remove bolts (91) that secure gear assembly (92) to retainer plate (95) . Remove gear
assembly (92) from manifold (84) .
50. Remove retaining ring (93) from bearing cage assembly (94) .
Illustration 49 g01083481
51. Install Tooling (H) into retainer plate (95) . Tighten Tooling (H) evenly until retainer plate
(95) is separated from bearing cage assembly (94) . Remove Tooling (H) . Remove retainer
plate (95) and bearing (96) from bearing cage assembly (94) .
Illustration 50 g00515864
52. Remove bolts (97) that secure bearing cage assembly (94) and the plates to manifold (84) .
23/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 51 g01083482
53. Install Tooling (H) into bearing cage assembly (94) . Tighten Tooling (H) evenly until
bearing cage assembly (94) is separated from manifold (84) . Remove Tooling (H) .
Remove bearing cage assembly (94) from manifold (84) .
Illustration 52 g00515866
54. Remove two metal seal rings (98) from bearing cage assembly (94) .
Illustration 53 g00515887
24/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. 55. Remove sleeve bearing (99) from bearing cage assembly (94) .
Illustration 54 g02607778
56. Remove bolts (100) that secure the transmission assembly and the torque converter
assembly to the transmission case.
Illustration 55 g02607796
57. Install Tooling (A) and a suitable lifting device to the transmission assembly. Remove the
transmission assembly and the torque converter assembly from the transmission case as one
unit. Remove Tooling (A) . The weight of the transmission assembly and the torque
converter assembly is approximately 218 kg (480 lb).
25/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Illustration 56 g02607797
58. Place Tooling (D) on suitable blocks. Place the transmission assembly and torque converter
assembly on Tooling (D) and the suitable blocks, as shown.
59. Remove bolts (101) and the washers that secure carrier assembly (102) to balance piston
(103) .
Illustration 57 g02607798
60. Install Tooling (A) and a suitable lifting device to carrier assembly (102) . Remove carrier
assembly (102) from balance piston (103) . The weight of carrier assembly (102) is
approximately 28 kg (62 lb). Remove Tooling (A) .
26/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 58 g01083483
61. Remove bolts (104) and thrust plate (105) from carrier assembly (102) . Use a hammer and
a punch in order to push pin (106) (not shown) into shaft (107) .
Illustration 59 g00515894
62. Remove shaft (107) , thrust discs (108) , and planetary gear (109) from carrier assembly
(102) . Remove bearing (110) from planetary gear (109) . Remove pin (106) from shaft
(107) .
63. Repeat Steps 61 and 62 for the two remaining shaft assemblies.
27/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 60 g01083484
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
64. Remove spring assemblies (111) , reaction dowels (112) , friction discs (113) , and clutch
plate (114) from balance piston (103) .
65. Remove the ten springs that are located under clutch plate (114) .
Illustration 61 g01084030
66. Remove plate assembly (115) and plates (116) from balance piston (103) . Remove ring
gear (117) from clutch housing (103) .
28/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
30. 67. If necessary, remove the five rivets and the two thrust washers from the ring gear assembly.
Illustration 62 g00515897
68. Remove clutch piston (118) from balance piston (103) . Remove seal ring (119) from clutch
piston (118) .
Illustration 63 g01084031
69. Remove retaining ring (120) from sun gear (121) . Remove sun gear (121) from shaft (122) .
29/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. Illustration 64 g00515899
70. Remove retaining ring (123) from housing assembly (124) . Refer to Illustration 65 in order
to view the housing assembly.
Illustration 65 g01084098
71. Install Tooling (A) and a suitable lifting device onto balance piston (103) . Remove balance
piston (103) and the carrier assembly from housing assembly (124) as a unit. Remove
Tooling (A) . The weight of the clutch housing (103) and the carrier assembly is
approximately 41 kg (90 lb).
30/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
32. Illustration 66 g01084099
72. Remove balance piston (103) from carrier assembly (125) . Remove O-ring seals (126) and
(127) from carrier assembly (125) . Remove seal ring (128) from carrier assembly (125) .
Illustration 67 g01084173
73. Turn over the carrier assembly. For assembly purposes, mark a line across the separation
between bearing cage (129) and carrier assembly (125) . Remove bolts (130) and the locks
that secure bearing cage (129) to carrier assembly (125) .
Illustration 68 g02670478
74. Install Tooling (H) into bearing cage (129) . Tighten Tooling (H) evenly until bearing cage
(129) separates from carrier assembly (125) . Remove Tooling (H) . Remove bearing cage
(129) from carrier assembly (126) .
31/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
33. Illustration 69 g00515904
75. Remove O-ring seals (131) from bearing cage (129) .
Illustration 70 g01084175
76. Remove metal seal ring (132) from bearing cage (129) . Use Tooling (E) and a hammer to
remove bearing (133) from bearing cage (129) .
Illustration 71 g00515906
32/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
34. 77. Use a hammer and a punch in order to push pin (134) into shaft (135) .
Illustration 72 g01084177
78. Remove shaft (135) , thrust discs (136) , and planetary gear (137) from carrier assembly
(126) . Remove bearing (138) from planetary gear (137) . Remove pin (134) from shaft
(135) .
79. Repeat Steps 77 and 78 for the two remaining shaft assemblies.
Illustration 73 g00515908
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
33/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
35. 80. Remove bolts (139) and the washers that secure front-end plate assembly (140) to housing
assembly (124) . Remove front-end plate assembly (140) from housing assembly (124) .
Illustration 74 g00515909
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
81. Remove springs (141) and reaction dowels (142) from housing assembly (124) .
34/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
36. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
37. Illustration 75 g01084182
82. Remove friction discs (143) and clutch plate (144) from housing assembly (124) . Remove
ring gear (145) from housing assembly (124) .
Illustration 76 g00515911
83. Remove clutch piston (146) from housing assembly (124) . Remove seal ring (147) from
clutch piston (146) . Remove seal ring (148) from housing assembly (124) .
Illustration 77 g00515912
84. Remove nuts (149) that secure housing assembly (124) to the torque converter.
35/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
38. Illustration 78 g01052945
85. Install Tooling (H) into manifold assembly (150) . Tighten Tooling (H) until manifold
assembly (150) separates from housing assembly (124) . Remove manifold assembly (150)
from housing assembly (124) . Remove Tooling (H) .
Illustration 79 g00515914
86. Remove bearing (151) from manifold assembly (150) . Remove seal rings (152) from
manifold assembly (150) .
36/37(W)
w
2021/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...