This document provides instructions for disassembling and assembling the implement pump on a 527 Track Skidder. It lists the required tools and outlines 37 steps to disassemble the pump by removing components like the head, cylinders, pistons, seals and bearings. It then describes 36 steps to reassemble the pump by installing these components in the reverse order. Safety notices are provided to relieve spring tension before removing or installing parts held under compression.
This document provides instructions for disassembling and removing the implement pump from a Caterpillar 527 Track Skidder. It outlines 36 steps to fully disassemble the implement pump, including removing hoses, nuts, washers, compensator components, pistons, springs, seals, bearings and other parts. Safety notices are provided regarding relieving pressure in hydraulic systems and releasing spring tension during disassembly. Detailed illustrations accompany each step.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It details the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Many parts like pistons, springs and seals must be removed and installed carefully. Safety precautions are provided to relieve pressure before working on hydraulic components.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures in detail with illustrations. Safety notices are included to release pressure from the hydraulic system before removal and to relieve spring tension carefully during disassembly. The multi-page document thoroughly explains each step to disassemble and reassemble the implement pump.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Detailed steps are provided to disassemble the pump components like the compensator, head, cylinders and pistons. Assembly instructions then describe cleaning and installing parts like seals, springs, bearings and swashplate in reverse order of disassembly. Safety notices are included to relieve pressure before removing lines or components.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Detailed steps are provided to disassemble the pump components like the compensator, head, cylinders and pistons. Assembly instructions specify cleaning parts and installing new seals before reassembling components like the barrel assembly, swashplate and housing. Safety notices are included to relieve pressure before removing lines or components.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...cdfvvv1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...jdjkskmikdkmd
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...paws21610697
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. It details 27 steps to disassemble the travel motor involving removing plates, barrels, pistons, gears, seals, and other components. It then lists 27 steps for reassembling the travel motor, applying sealant and torque specifications where needed and noting the importance of cleanliness during assembly.
This document provides instructions for disassembling and removing the implement pump from a Caterpillar 527 Track Skidder. It outlines 36 steps to fully disassemble the implement pump, including removing hoses, nuts, washers, compensator components, pistons, springs, seals, bearings and other parts. Safety notices are provided regarding relieving pressure in hydraulic systems and releasing spring tension during disassembly. Detailed illustrations accompany each step.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It details the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Many parts like pistons, springs and seals must be removed and installed carefully. Safety precautions are provided to relieve pressure before working on hydraulic components.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures in detail with illustrations. Safety notices are included to release pressure from the hydraulic system before removal and to relieve spring tension carefully during disassembly. The multi-page document thoroughly explains each step to disassemble and reassemble the implement pump.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Detailed steps are provided to disassemble the pump components like the compensator, head, cylinders and pistons. Assembly instructions then describe cleaning and installing parts like seals, springs, bearings and swashplate in reverse order of disassembly. Safety notices are included to relieve pressure before removing lines or components.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Detailed steps are provided to disassemble the pump components like the compensator, head, cylinders and pistons. Assembly instructions specify cleaning parts and installing new seals before reassembling components like the barrel assembly, swashplate and housing. Safety notices are included to relieve pressure before removing lines or components.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...cdfvvv1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...jdjkskmikdkmd
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...paws21610697
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. It details 27 steps to disassemble the travel motor involving removing plates, barrels, pistons, gears, seals, and other components. It then lists 27 steps for reassembling the travel motor, applying sealant and torque specifications where needed and noting the importance of cleanliness during assembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...uddksemd8ud
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f7djidksmd3e
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fikskkdmmd1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...yan77xunhao
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing tracks and sprockets, and then disconnecting hoses and removing bolts to take the travel motor off the undercarriage frame. Disassembly of the travel motor includes removing plates, barrels, pistons, gears, shafts, seals and other components. Reassembly follows the reverse order and notes to replace seals, apply oil, and ensure cleanliness.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f8usiedkdmm
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. The procedures include removing mounting bolts and studs, disconnecting air lines, and using valve spring compressors. Safety notices are provided to keep parts clean and contain fluids properly during maintenance. Diagrams illustrate the component locations and sequences.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. The procedures include removing mounting bolts and studs, disconnecting air lines, and using valve spring compressors. Precautions are given to keep parts clean and contain fluids during maintenance. Diagrams illustrate the component locations and sequences.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety notices are also provided.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
This document provides instructions for removing and installing the transmission transfer gears on a Caterpillar 651E wheel tractor. The process involves removing 18 components from the transfer gears including gears, couplings, bearings, seals and bolts. Reinstallation is the reverse of the removal process and includes checking bearing end play and installing new seals. Proper heating and pressing of bearings is required during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes using various tools to support the camshaft and guide it out of and back into the cylinder head. Precautions are listed to keep the camshaft level and aligned during removal and installation to avoid damage. Lubrication of parts and use of thread lock compound are also specified in the multi-step procedures.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies heating the new seal before pressing it into the flywheel housing with a driver plate until it is fully seated. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...shibi1322
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...shibi1322
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing several other components first, including the camshaft gear and rocker arms. Tools are then used to support the camshaft as it is moved out of the cylinder head and into a guide tool to prevent damage to the camshaft bearings during removal.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
This document provides instructions for removing and installing various components of a Caterpillar 3306 engine, including:
1. Removing and installing the spacer plate, water directors, lifter group, camshaft, and camshaft bearings.
2. Detailed procedures are given for each component, including required tools and special notes about cleaning, lubrication, and ensuring proper timing.
3. The document is part of a service repair manual for a Caterpillar 639D wheel scraper model powered by a 3306 engine.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including housing assemblies, clutch pistons, friction disks, bearings, gears, and seals. It then describes assembling the torque converter in 25 steps by reversing the removal process and provides torque specifications for fasteners. The goal is to separate, remove, and reassemble each component of the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift heavy components.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
More Related Content
Similar to Caterpillar Cat 527 TRACK SKIDDER (Prefix PTR) Service Repair Manual Instant Download.pdf
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...uddksemd8ud
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f7djidksmd3e
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fikskkdmmd1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...yan77xunhao
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing tracks and sprockets, and then disconnecting hoses and removing bolts to take the travel motor off the undercarriage frame. Disassembly of the travel motor includes removing plates, barrels, pistons, gears, shafts, seals and other components. Reassembly follows the reverse order and notes to replace seals, apply oil, and ensure cleanliness.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f8usiedkdmm
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. The procedures include removing mounting bolts and studs, disconnecting air lines, and using valve spring compressors. Safety notices are provided to keep parts clean and contain fluids properly during maintenance. Diagrams illustrate the component locations and sequences.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. The procedures include removing mounting bolts and studs, disconnecting air lines, and using valve spring compressors. Precautions are given to keep parts clean and contain fluids during maintenance. Diagrams illustrate the component locations and sequences.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety notices are also provided.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
Similar to Caterpillar Cat 527 TRACK SKIDDER (Prefix PTR) Service Repair Manual Instant Download.pdf (12)
This document provides instructions for removing and installing the transmission transfer gears on a Caterpillar 651E wheel tractor. The process involves removing 18 components from the transfer gears including gears, couplings, bearings, seals and bolts. Reinstallation is the reverse of the removal process and includes checking bearing end play and installing new seals. Proper heating and pressing of bearings is required during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes using various tools to support the camshaft and guide it out of and back into the cylinder head. Precautions are listed to keep the camshaft level and aligned during removal and installation to avoid damage. Lubrication of parts and use of thread lock compound are also specified in the multi-step procedures.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies heating the new seal before pressing it into the flywheel housing with a driver plate until it is fully seated. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...shibi1322
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...shibi1322
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing several other components first, including the camshaft gear and rocker arms. Tools are then used to support the camshaft as it is moved out of the cylinder head and into a guide tool to prevent damage to the camshaft bearings during removal.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
This document provides instructions for removing and installing various components of a Caterpillar 3306 engine, including:
1. Removing and installing the spacer plate, water directors, lifter group, camshaft, and camshaft bearings.
2. Detailed procedures are given for each component, including required tools and special notes about cleaning, lubrication, and ensuring proper timing.
3. The document is part of a service repair manual for a Caterpillar 639D wheel scraper model powered by a 3306 engine.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including housing assemblies, clutch pistons, friction disks, bearings, gears, and seals. It then describes assembling the torque converter in 25 steps by reversing the removal process and provides torque specifications for fasteners. The goal is to separate, remove, and reassemble each component of the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift heavy components.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
This document provides disassembly instructions for the transmission planetary system of a 637G Wheel Tractor. It outlines 50 steps to fully disassemble the transmission, including removing clutch housings, carrier assemblies, shafts, gears, plates, rings, seals and other components. Special care must be taken when removing components under spring pressure. Various tools are required to properly support, secure and remove parts from the transmission.
This document provides instructions for disassembling a torque converter in a 637G wheel tractor. It lists 32 steps to remove various components of the torque converter including carriers, gears, shafts, seals, and housings. Tools required are also listed, such as retaining ring pliers, driver groups, pullers, and link brackets. Care must be taken to contain fluids and protect parts from contamination.
This document provides assembly instructions for a torque converter in a 637G wheel tractor-scraper. It details 31 steps to assemble the torque converter, including installing seals, gears, shafts, bearings and housings in the proper order and with specified torques. It also provides disassembly instructions for the transfer gears in 18 steps, removing components like seals, bolts, cages and shafts. Tools required include drivers, pullers, link brackets and dial indicators.
This document provides assembly instructions for a torque converter in a 637G wheel tractor. It outlines 33 steps to assemble the various components of the torque converter like bearings, seals, gears, and housing. Proper cleaning and torque specifications are noted. Additionally, the document describes disassembly and assembly procedures for transfer gears in the wheel tractor, including removing 18 components like bolts, seals, and bearings. Tools required are listed for both procedures.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Tractor. It describes removing over 30 individual components in multiple steps, including removing the torque converter housing, retarder, gears, bearings, seals and other internal parts. Detailed illustrations accompany each step. Cleanliness is emphasized to prevent contaminating the hydraulic system.
This document provides instructions for removing and installing a cylinder head, lifter group, and camshaft on a Caterpillar 3408E or 3412E engine. The removal process involves detaching various components and hoses from the cylinder head and loosening bolts. Special tools are required to safely lift and handle parts due to their heavy weight. The installation follows the reverse order and specifies applying sealant and oil to parts and tightening bolts in a sequence with a torque wrench. Precautions are given to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the transmission of a 637E wheel tractor. It lists 47 steps to disassemble the transmission and 21 steps to reassemble it. Some key parts that are disassembled include the housing assembly, planetary group, carrier assemblies, gears, discs, plates, pistons, shafts, seals, springs, snap rings, and bearings. The instructions provide details on removing and installing each part using various tools. Weights of the major components are provided to aid in removal and installation.
This document provides instructions for disassembling and assembling the torque converter of a 627H Wheel Tractor. It describes 18 steps to disassemble the torque converter by removing various parts like retaining rings, bolts, seals, bearings, and assemblies. It then describes 24 steps to reassemble the torque converter by installing these same parts in the reverse order. The document includes illustrations and lists any required tools for each step.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing gears, bearing cages, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including pressing bearings onto gears, installing cups and cages, adjusting shims to achieve proper end play, and torquing bolts. Tools required are also listed.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing bearing cages, gears, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including cleaning parts, pressing bearings onto gears, adjusting shim thickness to achieve proper end play, and torquing bolts to the specified values. Tools required are also listed.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014257
Implement Pump - Remove
SMCS - 5084-011
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
1/3
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Use the following procedure to release the pressure in the hydraulic system:
a. Lower the implements to the ground.
b. Shut off the engine.
c. Move the control levers through the full travel distance of the levers. This will relieve
any pressure in the pilot system.
d. Slowly loosen the filler cap on the hydraulic oil tank in order to release the pressure.
e. Tighten the filler cap on the hydraulic oil tank.
f. The pressure in the hydraulic system has now been relieved. Lines and components
can now be removed.
Note: Put identification on all lines, hoses, wires, and tubes for installation purposes.
Install a cap or plug on all lines, hoses, and tubes that are disconnected. The caps
and/or plugs prevent the loss of fluid and contaminants cannot enter the system.
Illustration 1 g00619640
1. The weight of the rear bottom guard is 70 kg (155 lb). Use a floor jack to support the guard.
Remove bolts (1) and rear bottom guard (2) .
2/3
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00619642
2. Disconnect hose assemblies (3), (4), (5), and (6) from the implement pump.
Illustration 3 g00619647
3. The weight of the implement pump is 33 kg (73 lb). Use a floor jack to support the pump.
4. Remove four nuts (7), the washers, and the implement pump from the machine.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 18:18:49 UTC+0800 2019
3/3
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014260
Implement Pump - Disassemble
SMCS - 5084-015
Disassembly Procedure
Start By:
A. Remove the implement pump.
Table 1
Required Tools
Tool Part Number Description Qty
A 1P-1858 Pliers 1
B 1P-0074 Slide Hammer Puller 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 1. Be sure that the outside of the implement pump is clean prior to disassembly.
Illustration 1 g00619940
2. Remove O-ring seal (1) from pump (2) .
Illustration 2 g00619942
3. Remove bolts (4) and compensator (3) from the pump.
2/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g00619947
Typical example
4. Remove plug (6), plug (8), spool (5), and spool (7) from compensator (3) .
Illustration 4 g00619949
Typical example
5. Remove locknuts (9) and (10) .
Illustration 5 g00619950
Typical example
6. Remove margin plug (15), guide (14), spring stop pin (13), spring (12), and guide (11) from
compensator (3) .
7. Remove screw (16) from margin plug (15) .
3/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 6 g00619952
Typical example
8. Remove compensator plug (21), guide (20), spring (19), and guide (18) from the
compensator.
9. Remove screw (22) from compensator plug (21) .
10. Remove plug (17) and the O-ring seal from the compensator.
11. Remove O-ring seals (23) from the compensator.
Illustration 7 g00619953
Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
4/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: A spring is held in compression by the head. The pump head can be pushed away
from the pump case very rapidly. The spring tension must be released before the last bolt is
removed from the head. In order to gradually release the spring tension, be sure that the
head moves away from the pump case as the bolts are loosened. The bolts in the head are
long enough to release all of the tension in the spring before the bolts are removed.
12. Remove bolts (25) and head (24) from pump (2) .
Illustration 8 g00619954
13. Remove cylinder (26) from head (24). Also remove the spacer under cylinder (26) .
14. Remove cylinder (27) and spring (28) .
Illustration 9 g00619956
15. Note the location of plate (29) and remove the plate.
5/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 10 g00619958
16. Remove pistons (30) and (31). Remove the O-ring seal from each of the pistons.
17. Remove bearing cup (32) .
18. If necessary, remove pin (33) .
Illustration 11 g00619959
19. Remove gasket (34) from pump (2) .
20. Remove bolts (35), cover (36), and the O-ring seal.
6/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 12 g00619962
21. Remove bearing cone (37) from the shaft.
22. Remove plug (38) and the O-ring seal.
Illustration 13 g00619963
23. Remove spacer (39) from the shaft.
Illustration 14 g00619964
7/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 24. Remove barrel assembly (40) from pump (2) .
Illustration 15 g00619965
Illustration 16 g00619966
Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
25. Use a press to compress spring (44). Use Tool (A) to remove snap ring (43) from the groove
in barrel (40) .
26. Slowly release the compression on spring (44) .
27. Remove guide (42), spring (44), and guide (41) from barrel (40) .
8/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: Guides (41) and (42) are a different size. Mark the guides for assembly purposes.
Illustration 17 g00619968
28. Remove shaft (45) from pump (2) .
Illustration 18 g00620030
29. Tilt swashplate (46), and pistons (47). Remove the components as an assembly from pump
(2) .
9/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 19 g00620031
30. Remove bolts (49). Remove plates (48) and (50) .
31. If necessary, remove stops (52) from swashplate (51) .
Illustration 20 g00620032
32. Remove pistons (47) from plate (53) .
Illustration 21 g00620033
10/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEB...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 33. Remove bearing cone (54) .
Illustration 22 g00620036
34. Remove bearing cup (56) .
35. Remove bolts (58) and swashplate bearings (55) and (57) .
Illustration 23 g00620037
36. Use Tool (B) and remove two lip seals (59) from the housing. Note the direction of the lip
seals for assembly.
37. Use Tooling (A) and remove two snap rings (60) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 18:19:38 UTC+0800 2019
11/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEB...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014262
Implement Pump - Assemble
SMCS - 5084-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 1P-1858 Pliers 1
B 1P-0510 Driver Group 1
1. Clean all of the parts and inspect all of the parts. If parts are damaged or worn, install new
parts. Put clean oil on all of the internal parts of the pump.
Note: Replace all O-ring seals, gaskets, and shaft seals.
Illustration 1 g00620037
1/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 2. Use Tool (A) to install two snap rings (60) .
3. Use Tool (B) to install two lip seals (59) in the housing.
Illustration 2 g00620036
4. Use bolts (58) to install swashplate bearings (55) and (57). Tighten bolts (58) to a torque of
4 ± .4 N·m (35 ± 3.5 lb in).
5. Install bearing cup (56) .
Illustration 3 g00620033
6. Install bearing cone (54) .
2/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
Note: Use the following procedure to assemble the components of barrel (40) .
9. Put guide (41), spring (44), and guide (42) in position in barrel (40) .
10. Use a press to compress spring (44). Use Tool (A) to install snap ring (43) .
11. Be sure that snap ring (43) is properly seated. Slowly release the compression on spring
(44) .
Illustration 7 g00620032
Illustration 8 g00620965
4/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 12. Install pistons (47) on plate (53). Install the pistons in barrel (40) .
Illustration 9 g00620969
13. Install assembled barrel (40), the plate, and the pistons on the shaft as a unit. Be sure that
the splines are aligned.
Illustration 10 g00620975
14. Apply 9S-3263 Thread Lock Compound to the threads of bolts (49). Install plates (48) and
(50) with the bolts. Tighten the bolts to a torque of 14 ± 1 N·m (124 ± 9 lb in).
5/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 11 g00619963
15. Install spacer (39) to the shaft.
Illustration 12 g00619962
16. Install plug (38) and the O-ring seal in pump (2). Tighten the plug to a torque of 101.5 ± 4.5
N·m (75 ± 3 lb ft).
17. Install bearing cone (37) on the shaft.
6/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 13 g00619959
18. Install the O-ring seal, cover (36), and bolts (35). Tighten the bolts to a torque of 8.5 ± 1
N·m (75 ± 9 lb in).
Note: If the shaft bearings, the shaft, the head, or the housing were replaced, an end play
adjustment must be made. To obtain axial shaft end play of .01 to .10 mm (.0004 to .0039
inch), use the required shims from the 9T-3038 Shaft Shim Kit .
19. Install gasket (34) on pump (2) .
Illustration 14 g00619958
20. Install the O-ring seals on pistons (30) and (31). Apply Loctite No. 680 sealant to the
threads of the pistons.
21. Install the pistons in head (24) and tighten to a torque of 79 ± 4 N·m (58 ± 3 lb ft).
22. If pin (33) was removed, install the pin.
23. Install bearing cup (32) .
Illustration 15 g00619956
7/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 24. Install plate (29). Be sure that the notch in the plate is aligned with pin (33) .
Illustration 16 g00619954
25. Install the spacer under cylinder (26) and install cylinder (26) in head (24) .
26. Install cylinder (27) and spring (28) .
Illustration 17 g00619953
27. Use bolts (25) to install head (24) to pump (2). Tighten the bolts evenly to a torque of 71 ±
14 N·m (52 ± 10 lb ft).
8/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 18 g00619952
28. Install O-ring seals (23) on the compensator.
29. Install the O-ring seal and plug (17) on the compensator. Tighten the plug to a torque of
30.5 ± 1.5 N·m (23 ± 1 lb ft).
30. Install screw (22) in compensator plug (21) .
31. Install guide (18), spring (19), guide (20), and compensator plug (21) in the compensator.
Illustration 19 g00619950
32. Install screw (16) in margin plug (15) .
33. Install guide (11), spring (12), spring stop pin (13), guide (14), and margin plug (15) in
compensator (3) .
9/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 20 g00619949
34. Tighten locknuts (9) and (10) to a torque of 17 ± 3 N·m (150 ± 26 lb in).
Note: Refer to Systems Operation, Testing and Adjusting, SENR9424 for the correct
procedure for adjusting the flow compensator.
Illustration 21 g00619947
35. Put spools (5) and (7) in position in the compensator.
36. Install plugs (6) and (8). Tighten the plugs to a torque of 30.5 ± 1.5 N·m (22 ± 1 lb ft).
10/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEB...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 22 g00619942
37. Use bolts (4) to install compensator (3) on the pump. Tighten the bolts to a torque of 34 ± 3
N·m (25 ± 2 lb ft).
Illustration 23 g00619940
38. Install O-ring seal (1) on pump (2) .
End By: Install the implement pump.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 18:20:27 UTC+0800 2019
11/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEB...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014258
Implement Pump - Install
SMCS - 5084-012
Installation Procedure
Illustration 1 g00619647
1. Be sure that the O-ring seal is in position on the front of the pump.
2. The approximate weight of the implement pump is 33 kg (73 lb). Use a floor jack to put the
implement pump in position.
3. Install the washers and four nuts (7) .
1/2
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 2 g00619642
4. Connect hose assemblies (3), (4), (5), and (6) to the implement pump.
Illustration 3 g00619640
5. The weight of the rear bottom guard is 70 kg (155 lb). Use bolts (1) and the washers to
install rear bottom guard (2) .
6. Fill the hydraulic tank to the correct level.
Note: For the correct procedure to fill the hydraulic system on the 527 Track-Type Skidder, refer
to Operation and Maintenance Manual, SEBU7001, "Hydraulic System Oil - Change".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 18:21:16 UTC+0800 2019
2/2
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
30. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014266
Bulldozer Control Valve - Remove
SMCS - 5115-011
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
1/8
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...