The document provides instructions for removing the transmission from a 427F2 backhoe loader. It lists the required tools and gives a step-by-step process that includes locking the boom, swing boom, and extendable stick in place. Key steps include using support stands under the rear axle housing and a hydraulic jack under the transmission case. Then bolts can be removed to separate the transmission from the engine and center housing.
The document provides instructions for removing and installing a transmission solenoid valve on a 427F2 backhoe loader. It describes disconnecting wiring harnesses, removing mounting bolts and plugs, and cutting cable straps to remove the solenoid valve. The installation is the reverse of removal, requiring reconnecting plugs and harnesses and tightening mounting bolts to the specified torque.
The document provides instructions for removing the transmission from a 427F2 backhoe loader. It lists the required tools which include support stands, an air/hydraulic jack, hydraulic jacks, and jack stands. The first steps involve connecting locks for the boom, swing boom, and extendable stick. Then the transmission housing cover and components inside the housing are removed to allow removal of the transmission.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support stands to lift the front and rear of the loader off the ground.
2) Draining the transmission oil before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the engine and rear axle housing.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using tools and jacks to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using pullers to separate housings, gears, seals and other parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
The document provides instructions for disassembling and removing various components of a 432F2 backhoe loader, including the axle housing, brake assembly, differential and bevel gear, solenoid valve, and releasing system pressure. Key steps include using various tools to remove bearings, gears, pins, seals, and other parts. Precautions are outlined for releasing spring pressure safely.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support stands to lift the front and rear of the loader off the ground.
2) Draining the transmission oil before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the engine and rear axle housing.
The document provides instructions for removing and installing a transmission solenoid valve on a 427F2 backhoe loader. It describes disconnecting wiring harnesses, removing mounting bolts and plugs, and cutting cable straps to remove the solenoid valve. The installation is the reverse of removal, requiring reconnecting plugs and harnesses and tightening mounting bolts to the specified torque.
The document provides instructions for removing the transmission from a 427F2 backhoe loader. It lists the required tools which include support stands, an air/hydraulic jack, hydraulic jacks, and jack stands. The first steps involve connecting locks for the boom, swing boom, and extendable stick. Then the transmission housing cover and components inside the housing are removed to allow removal of the transmission.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support stands to lift the front and rear of the loader off the ground.
2) Draining the transmission oil before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the engine and rear axle housing.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using tools and jacks to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using pullers to separate housings, gears, seals and other parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
The document provides instructions for disassembling and removing various components of a 432F2 backhoe loader, including the axle housing, brake assembly, differential and bevel gear, solenoid valve, and releasing system pressure. Key steps include using various tools to remove bearings, gears, pins, seals, and other parts. Precautions are outlined for releasing spring pressure safely.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support stands to lift the front and rear of the loader off the ground.
2) Draining the transmission oil before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the engine and rear axle housing.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Placing jack stands under the front and rear of the loader to lift it 1270 mm off the ground for access.
2) Draining the transmission oil per the operation manual before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the loader.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and disassemble brake assemblies, gears, and shafts. Proper safety procedures and cleaning of parts is emphasized throughout.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support stands to lift the front and rear of the loader off the ground.
2) Draining the transmission oil before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the engine and rear axle assembly.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
The document provides instructions for disassembling and removing various components of a 432F2 backhoe loader, including the axle housing, brake assembly, differential and bevel gear, solenoid valve, and releasing system pressure. Key steps include using various tools to remove bearings, gears, pins, seals, and other parts. Precautions are outlined for releasing spring pressure safely.
The document provides instructions for disassembling an axle housing on a 432F2 backhoe loader. It lists required tools and gives 26 steps to remove components such as brake discs, pistons, cylinders, gears, seals, and bearings. The overall goal is to disassemble the service brakes, differential, and bevel gear.
The document provides instructions for disassembling an axle housing on a 432F2 backhoe loader. It lists required tools and gives 26 steps to remove components such as brake discs, pistons, cylinders, gears, seals, and bearings. The overall goal is to disassemble the service brakes, differential, and bevel gear.
The document provides instructions for disassembling an axle housing on a 432F2 backhoe loader. It lists required tools and gives 26 steps to remove components such as brake discs, pistons, cylinders, gears, seals, and bearings. The overall goal is to disassemble the service brakes, differential, and bevel gear.
The document provides instructions for disassembling the axle housing of a 432F2 backhoe loader. It describes 26 steps to remove components such as brake discs, pistons, cylinders, bearings, seals, gears, and shafts. Special tools are required to remove some parts, and safety precautions are mentioned.
The document provides instructions for disassembling an axle housing on a 432F2 backhoe loader. It lists required tools and gives 26 steps to remove components such as brake discs, pistons, cylinders, gears, seals, and bearings. The overall goal is to disassemble the service brakes, differential, and bevel gear.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine off the ground.
2) Draining the transmission oil before removal.
3) Removing mounting bolts, brackets, and electrical connections to separate the transmission from the engine and rear axle housing.
4) Using pullers and presses to remove bearings and shafts from the transmission.
5) Tagging and storing components to aid reassembly.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine, draining the transmission fluid.
2) Removing mounting bolts, brackets and hoses to separate the transmission from the engine and rear axle housing.
3) Using overhead lift equipment to remove the transmission once it is fully separated from the machine.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine, draining the transmission fluid.
2) Removing mounting bolts, brackets and hoses to separate the transmission from the engine and rear axle housing.
3) Using overhead lift equipment to remove the transmission once it is fully separated from the machine.
The document provides instructions for disassembling and assembling various components of a 432F2 backhoe loader, including:
1) Removing the axle housing, brake assemblies, differential and bevel gear assembly.
2) Removing bearings from the axle housing and differential.
3) Disassembling the differential into individual parts.
4) Releasing hydraulic pressure from the system before disassembly.
This document provides instructions for removing and installing the transmission transfer gears on a Caterpillar 651E wheel tractor. The process involves removing 18 components from the transfer gears including gears, couplings, bearings, seals and bolts. Reinstallation is the reverse of the removal process and includes checking bearing end play and installing new seals. Proper heating and pressing of bearings is required during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes using various tools to support the camshaft and guide it out of and back into the cylinder head. Precautions are listed to keep the camshaft level and aligned during removal and installation to avoid damage. Lubrication of parts and use of thread lock compound are also specified in the multi-step procedures.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies heating the new seal before pressing it into the flywheel housing with a driver plate until it is fully seated. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...shibi1322
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
More Related Content
Similar to Caterpillar Cat 427F2 Backhoe Loader (Prefix HWK) Service Repair Manual Instant Download.pdf
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Placing jack stands under the front and rear of the loader to lift it 1270 mm off the ground for access.
2) Draining the transmission oil per the operation manual before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the loader.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and disassemble brake assemblies, gears, and shafts. Proper safety procedures and cleaning of parts is emphasized throughout.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support stands to lift the front and rear of the loader off the ground.
2) Draining the transmission oil before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the engine and rear axle assembly.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It outlines 26 steps to completely disassemble the axle housing and related components. The key steps include using jacks and stands to lift and support the machine, draining transmission fluid, removing mounting bolts and plates, and using various tools to pull bearings and separate individual parts. Protective equipment is recommended when removing pressurized components.
The document provides instructions for disassembling and removing various components of a 432F2 backhoe loader, including the axle housing, brake assembly, differential and bevel gear, solenoid valve, and releasing system pressure. Key steps include using various tools to remove bearings, gears, pins, seals, and other parts. Precautions are outlined for releasing spring pressure safely.
The document provides instructions for disassembling an axle housing on a 432F2 backhoe loader. It lists required tools and gives 26 steps to remove components such as brake discs, pistons, cylinders, gears, seals, and bearings. The overall goal is to disassemble the service brakes, differential, and bevel gear.
The document provides instructions for disassembling an axle housing on a 432F2 backhoe loader. It lists required tools and gives 26 steps to remove components such as brake discs, pistons, cylinders, gears, seals, and bearings. The overall goal is to disassemble the service brakes, differential, and bevel gear.
The document provides instructions for disassembling an axle housing on a 432F2 backhoe loader. It lists required tools and gives 26 steps to remove components such as brake discs, pistons, cylinders, gears, seals, and bearings. The overall goal is to disassemble the service brakes, differential, and bevel gear.
The document provides instructions for disassembling the axle housing of a 432F2 backhoe loader. It describes 26 steps to remove components such as brake discs, pistons, cylinders, bearings, seals, gears, and shafts. Special tools are required to remove some parts, and safety precautions are mentioned.
The document provides instructions for disassembling an axle housing on a 432F2 backhoe loader. It lists required tools and gives 26 steps to remove components such as brake discs, pistons, cylinders, gears, seals, and bearings. The overall goal is to disassemble the service brakes, differential, and bevel gear.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine off the ground.
2) Draining the transmission oil before removal.
3) Removing mounting bolts, brackets, and electrical connections to separate the transmission from the engine and rear axle housing.
4) Using pullers and presses to remove bearings and shafts from the transmission.
5) Tagging and storing components to aid reassembly.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine, draining the transmission fluid.
2) Removing mounting bolts, brackets and hoses to separate the transmission from the engine and rear axle housing.
3) Using overhead lift equipment to remove the transmission once it is fully separated from the machine.
This document provides instructions for disassembling and removing the transmission from a 432F2 backhoe loader. It describes:
1) Positioning jack stands and support tubes to lift the front and rear of the machine, draining the transmission fluid.
2) Removing mounting bolts, brackets and hoses to separate the transmission from the engine and rear axle housing.
3) Using overhead lift equipment to remove the transmission once it is fully separated from the machine.
The document provides instructions for disassembling and assembling various components of a 432F2 backhoe loader, including:
1) Removing the axle housing, brake assemblies, differential and bevel gear assembly.
2) Removing bearings from the axle housing and differential.
3) Disassembling the differential into individual parts.
4) Releasing hydraulic pressure from the system before disassembly.
Similar to Caterpillar Cat 427F2 Backhoe Loader (Prefix HWK) Service Repair Manual Instant Download.pdf (18)
This document provides instructions for removing and installing the transmission transfer gears on a Caterpillar 651E wheel tractor. The process involves removing 18 components from the transfer gears including gears, couplings, bearings, seals and bolts. Reinstallation is the reverse of the removal process and includes checking bearing end play and installing new seals. Proper heating and pressing of bearings is required during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes using various tools to support the camshaft and guide it out of and back into the cylinder head. Precautions are listed to keep the camshaft level and aligned during removal and installation to avoid damage. Lubrication of parts and use of thread lock compound are also specified in the multi-step procedures.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies heating the new seal before pressing it into the flywheel housing with a driver plate until it is fully seated. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...shibi1322
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...shibi1322
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing several other components first, including the camshaft gear and rocker arms. Tools are then used to support the camshaft as it is moved out of the cylinder head and into a guide tool to prevent damage to the camshaft bearings during removal.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
This document provides instructions for removing and installing various components of a Caterpillar 3306 engine, including:
1. Removing and installing the spacer plate, water directors, lifter group, camshaft, and camshaft bearings.
2. Detailed procedures are given for each component, including required tools and special notes about cleaning, lubrication, and ensuring proper timing.
3. The document is part of a service repair manual for a Caterpillar 639D wheel scraper model powered by a 3306 engine.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including housing assemblies, clutch pistons, friction disks, bearings, gears, and seals. It then describes assembling the torque converter in 25 steps by reversing the removal process and provides torque specifications for fasteners. The goal is to separate, remove, and reassemble each component of the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift heavy components.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
This document provides disassembly instructions for the transmission planetary system of a 637G Wheel Tractor. It outlines 50 steps to fully disassemble the transmission, including removing clutch housings, carrier assemblies, shafts, gears, plates, rings, seals and other components. Special care must be taken when removing components under spring pressure. Various tools are required to properly support, secure and remove parts from the transmission.
This document provides instructions for disassembling a torque converter in a 637G wheel tractor. It lists 32 steps to remove various components of the torque converter including carriers, gears, shafts, seals, and housings. Tools required are also listed, such as retaining ring pliers, driver groups, pullers, and link brackets. Care must be taken to contain fluids and protect parts from contamination.
This document provides assembly instructions for a torque converter in a 637G wheel tractor-scraper. It details 31 steps to assemble the torque converter, including installing seals, gears, shafts, bearings and housings in the proper order and with specified torques. It also provides disassembly instructions for the transfer gears in 18 steps, removing components like seals, bolts, cages and shafts. Tools required include drivers, pullers, link brackets and dial indicators.
This document provides assembly instructions for a torque converter in a 637G wheel tractor. It outlines 33 steps to assemble the various components of the torque converter like bearings, seals, gears, and housing. Proper cleaning and torque specifications are noted. Additionally, the document describes disassembly and assembly procedures for transfer gears in the wheel tractor, including removing 18 components like bolts, seals, and bearings. Tools required are listed for both procedures.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Tractor. It describes removing over 30 individual components in multiple steps, including removing the torque converter housing, retarder, gears, bearings, seals and other internal parts. Detailed illustrations accompany each step. Cleanliness is emphasized to prevent contaminating the hydraulic system.
This document provides instructions for removing and installing a cylinder head, lifter group, and camshaft on a Caterpillar 3408E or 3412E engine. The removal process involves detaching various components and hoses from the cylinder head and loosening bolts. Special tools are required to safely lift and handle parts due to their heavy weight. The installation follows the reverse order and specifies applying sealant and oil to parts and tightening bolts in a sequence with a torque wrench. Precautions are given to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the transmission of a 637E wheel tractor. It lists 47 steps to disassemble the transmission and 21 steps to reassemble it. Some key parts that are disassembled include the housing assembly, planetary group, carrier assemblies, gears, discs, plates, pistons, shafts, seals, springs, snap rings, and bearings. The instructions provide details on removing and installing each part using various tools. Weights of the major components are provided to aid in removal and installation.
This document provides instructions for disassembling and assembling the torque converter of a 627H Wheel Tractor. It describes 18 steps to disassemble the torque converter by removing various parts like retaining rings, bolts, seals, bearings, and assemblies. It then describes 24 steps to reassemble the torque converter by installing these same parts in the reverse order. The document includes illustrations and lists any required tools for each step.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing gears, bearing cages, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including pressing bearings onto gears, installing cups and cages, adjusting shims to achieve proper end play, and torquing bolts. Tools required are also listed.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing bearing cages, gears, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including cleaning parts, pressing bearings onto gears, adjusting shim thickness to achieve proper end play, and torquing bolts to the specified values. Tools required are also listed.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 427F2 BACKHOE LOADER HWK
Configuration: 427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i06194852
Axle Housing (Service Brakes, Differential and Bevel Gear) -
Disassemble
SMCS - 3256-015; 3258-015; 3260-015; 4251-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 202-7965 Spanner Wrench 1
B 1P-2321 Combination Puller 1
C 235-2784 Adjusting Tool Gp 1
D 8H-0663 Bearing Puller Gp 1
Start By:
a. Remove the axle housing.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01636808
1. Remove plates (1), brake discs (2), and brake hub (4) from the brake cylinder assembly.
Remove dowels (3).
Illustration 2 g01636809
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (10), washers (9), bushing (8), and spacer (7). Remove bolts (16), retainers
(15), springs (14), springs (13), and bushings (12), as an assembly. Use a suitable pry bar
and remove brake piston (6) from brake cylinder assembly (11). Remove O-ring seals (5)
from brake piston (6). Repeat this step for the opposite side.
Illustration 3 g01636811
3. Remove bolts (17) from brake cylinder assembly (11).
Illustration 4 g01636812
3/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Note: Before you remove brake cylinder assembly (11), make location marks for
installation purposes.
4. Remove brake cylinder assembly (11).
5. Repeat Step 3 and Step 4 for the opposite side.
6. Remove the differential and bevel gear assembly (18) from the bevel gear side of the center
housing.
Illustration 5 g01637013
7. Remove bolt (20) and retainer (19). Use Tooling (A) to remove spanner nut (22). If
necessary, remove bearing cup (21) from brake cylinder assembly (11). Repeat this step for
the opposite side.
4/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g01637914
8. Use Tooling (B) in order to remove bearing cone (23).
5/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 7 g01637979
9. Lock the differential in a vise. Remove bolts (24) and bevel gear (25) from the differential.
6/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 8 g01637980
10. Use Tooling (B) to remove bearing cone (26).
Illustration 9 g01637981
11. Remove collar (28), pins (27), and the seals.
7/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 10 g01637983
12. Remove cover (29), thrust washer (30), and side gear (32). Use a suitable punch and a
hammer in order to drive out locking pins (31). Remove planetary shafts (33).
Illustration 11 g01638818
13. Remove thrust washers (34), gears (35), spider (36), side gear (38), and thrust washer (37).
8/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 12 g01638823
14. Remove bolts (40) and remove brake assembly (39) as a unit. Straighten the locking tab
from nut (41).
Illustration 13 g01638831
15. Use Tooling (C) in order to hold brake disc (42) and remove nut (41) (not shown).
9/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 14 g01638834
16. Remove washer (44), O-ring seal (43), and brake disc (42).
Illustration 15 g01638835
17. Remove lip seal (45) from the center housing.
10/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 16 g01639076
18. Tap the end of pinion shaft (46) with a soft hammer in order to remove pinion shaft (46)
from the center housing.
Illustration 17 g01639077
19. Remove bearing cone (48), washers (49), and collapsible spacer (47) from pinion shaft (46).
Discard collapsible spacer (47).
11/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 18 g01639080
20. Use Tooling (D) and a suitable press in order to remove bearing cone (50) from pinion shaft
(46). Remove the shim that is positioned under bearing cone (50). Check the shim for wear.
If necessary, replace the shim.
Illustration 19 g01639081
12/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
21. Remove bolts (66), cover (65), and O-ring seal (64).
22. Remove piston (63) from cover (65). Remove O-ring seals (62) from piston (63).
23. Remove retaining ring (61), bushing (60), and spring (59) from rod (55).
24. Remove bolts (51), cover (52), O-ring seal (53), spring (54), and washer (56) from the
center housing.
25. Remove rod (55) from fork (58). Remove retaining ring (57) from rod (55). Remove fork
(58) from the center housing.
Illustration 20 g01639082
26. Use a suitable hammer and a punch in order to remove bearing cups (67) from the center
housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 7 11:43:05 UTC+0800 2019
13/13
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 427F2 BACKHOE LOADER HWK
Configuration: 427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i06038944
System Pressure - Release
SMCS - 4250-553-PX; 4300-553-PX; 5050-553-PX
Release Procedure
1. Park on a level surface. If you must park on a grade, chock the machine.
2. Apply the service brake in order to stop the machine. Move the transmission control to the
NEUTRAL position.
3. Move the speed control lever to the LOW IDLE position.
4. Engage the parking brake.
5. Engage the transmission neutral lock.
6. Lower all attachments to the ground.
7. Stop the engine.
8. Turn the engine start switch key to OFF position for 4 seconds.
9. Turn the engine start switch key back to ON position without starting the engine.
10. Press the hydraulic shutoff switch to the ON position.
11. Operate all hydraulic controls through all positions in order to relieve hydraulic pressure.
Repeat this step until all hydraulic pressure is released.
12. Move the hydraulic control levers to the HOLD position.
13. Turn the engine start switch to OFF position and remove the key.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 7 11:44:01 UTC+0800 2019
1/1
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 427F2 BACKHOE LOADER HWK
Configuration: 427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i06190624
Solenoid Valve (Transmission) - Remove and Install
SMCS - 5479-010-T3
Removal Procedure
Illustration 1 g03822061
1. Remove bolts (2), plate (3), and floor mat (1).
1/2
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g03822065
2. Remove bolts (4) and position floorplate (5) to the side.
Illustration 3 g01658935
3. Cut cable straps (8). Disconnect harness assemblies (7). Remove the four plugs and bolts
(6). Remove solenoid valve (9). Repeat for the remaining solenoid valves.
Installation Procedure
1. Install solenoid valve (9) in the reverse order of removal.
a. Tighten bolts (6) in a crisscross pattern to a torque of 1 N·m (9 lb in). Retorque bolts
(6) to a final torque of 8 N·m (71 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 7 11:44:57 UTC+0800 2019
2/2
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 427F2 BACKHOE LOADER HWK
Configuration: 427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i06145776
Transmission (Direct Drive) - Remove
SMCS - 3030-011-DD
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-2352 Support Stand As 2
B 444-0526 Air/Hydraulic Jack Gp 1
C
8S-7640 Stand 2
8S-7611 Tube 2
8S-7615 Pin 2
D
1U-7505 Hydraulic Jack 1
1U-7558 Mounting Adapter Gp 2
E 456-4449 Support Tube 1
F 1U-7505 Hydraulic Jack 1
G 308-3471 Jack Stand Gp 2
1. Connect the lock for the boom. Refer to Operation and Maintenance Manual, "Boom Lock".
2. Connect the lock for the swing boom. Operation and Maintenance Manual, "Swing Lock
Pin Control".
3. Connect the lock for the extendable stick. Refer to Operation and Maintenance Manual,
"Extendable Stick Lock Control ".
1/8
427F2 Side Shift Backhoe Loader HWK00001-UP (MACHINE) POWERED BY C3.4...
2019/12/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...