Technical Sheet – Gravestone support brackets (“Compact brackets” model). Features, size and mounting methods

1. REAL VOTIVA STORE
Online funeral articles shop
www.realvotivastore.com
info@realvotivastore.com
Pag. 1 di 4
Technical Sheet – Gravestone support brackets (“Compact brackets” model)
Features, size and mounting methods
General features
The bronze brackets are used to support flat marble or granite gravestone.
The "Compact Bracket" model is characterized by adjustable lugs variable from 0.8 to 2 cm, depending on
the bracket size.
Bronze brackets are available in different sizes and colours, such as simple material like bronze, glitter /
glitter light bronze, black or white ceramismalt, chromium, mercury, marble colours like Carrara, Botticino,
Guatemala green or Marquinia black.
These products are covered with a special coating that ensures weatherproof and are very useful especially
for outdoors planted graves.
The supply of the brackets includes the stainless steel threaded pins for fixing.
Brackets sizes
Compact Brackets are available in various sizes. The typical bracket sizes indicated in detail in the catalogue
are the height of the main body (H1), also reported in the item code, and the total height of the bracket
(H2) including the lugs. Depending on bracket size, the diameter (M) of the central fixing threaded pin (to
be screwed in the back) can vary from 6 mm to 10 mm.
For example, the compact bracket with item code “P.10.2820/8 cm 8x16 M10” has the following
measures: height of the main body H1 = 8 cm, total height including lugs H2 =16 cm, pivot diameter 10 mm
(M10). The height of the main body is also reported in item code after the slash (“P.10.2820/ 8 ”).

2. REAL VOTIVA STORE
Online funeral articles shop
www.realvotivastore.com
info@realvotivastore.com
Pag. 2 di 4
Technical specifications
The compact bracket is available in the following sizes:
 cm 6 x 14, M8 or M10 (body height 6 cm, short lugs)
 cm 6 x 18, M8 (body height 6 cm, long lugs)
 cm 8 x 16, M8 or M10 (body height 8 cm, short lugs)
 cm 8 x 19, M8 (body height 8 cm, long lugs)
Also available are half brackets to be used for the first and last of a vertical series of flat headstones. Half
brackets are available in the following sizes:
 cm 4,5 x 8, M8 or M10 (body height 4,5 cm, short lugs)
 cm 4,5 x 10, M8 (body height 6 cm, long lugs)
Smaller brackets are available for ossuaries in the following sizes:
 cm 3,5 x 7,5 M8 (entire)
 cm 2,5 x 4,5 M8 (half)
The following figure shows the common measures for all brackets sizes (except for ossuaries brackets and 0
thick brackets).
L1 = 2,5 cm L2= 5 cm P = 3 cm S = 0,8 2 cm M = 8 o 10 mm

3. REAL VOTIVA STORE
Online funeral articles shop
www.realvotivastore.com
info@realvotivastore.com
Pag. 3 di 4
How to mount the brackets
For mounting the brackets it is used a threaded steel pin which, on one hand, is screwed into the back of
the bracket (see figure), and, on the other, is attached to the wall by means of an expansion bolt.
Once fastened the brackets, loosen the lugs using the nuts and place the tombstones on the top edge of
the body of each bracket; lower brackets are load‐bearing while the upper ones are blocking the headstone
through the lugs.
In the following figure is outlined as an example the section of a mounted bracket (cm 8 x 16).
The vertical distance between a flat grave and the other is determined by the height of the central body of
the bracket (H1).

4. REAL VOTIVA STORE
Online funeral articles shop
www.realvotivastore.com
info@realvotivastore.com
Pag. 4 di 4
The following picture shows the final result of mounting a series of flat graves supported by bronze
compact brackets.
REAL VOTIVA STORE ‐ Online funeral articles shop
Contrada Pozzo, 73040 ‐ Melissano ‐ LECCE (Italy)
www.realvotivastore.com
info@realvotivastore.com