Caterpillar Cat 24M Motor Grader (Prefix B93) Service Repair Manual (B9300001 and up).pdf

Service Repair Manual
Models
24M Motor Grader

Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 24M MOTOR GRADER B93
Configuration: 24M Motor Grader B9300001-UP (MACHINE) POWERED BY C18 Engine
Disassembly and Assembly
24M Motor Grader Machine Systems
Media Number -UENR3490-00 Publication Date -01/06/2013 Date Updated -10/06/2013
i07080592
Piston Pump (Implement) - Disassemble
SMCS - 5070-015-II; 5084-015-QP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 1P-1857 Retaining Ring Pliers 1
C 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Implement) -
Remove".
1/8
24M Motor Grader B9300001-UP (MACHINE) POWERED BY C18 Engine(SEBP63...
2020/11/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01329899
1. Remove bolts (1) and valve (2).
2. Remove O-ring seals (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (9), the O-ring seal, retainer (8), spring (7), retainer (6), spool (5), plug (4),
and the O-ring seal.
2/8
2020/11/25

4. Remove plug (16), the O-ring seal, retainer (15), spring (14), rod (13), retainer (12), spool
(11), plug (10), and the O-ring seal.
5. Remove bolts (17) and head (18).
6. Remove piston (22), piston (21), spring (24), gasket (19), port plate (20), and bearing cup
(23).
3/8
2020/11/25

7. Remove bearing cone (25).
8. Remove shim (26), barrel (27), and dowel (28).
4/8
2020/11/25

9. Use Tooling (A), Tooling (B), and a suitable press to remove retaining ring (32) from barrel
(27).
10. Remove washer (31), spring (30), and washer (29).
11. Remove bolts (33) and cover (34).
5/8
2020/11/25

12. Remove O-ring seal (35).
13. Remove plug (36).
14. Remove shaft (37), bolts (39), and plates (38).
6/8
2020/11/25

15. Remove plates (40), retainer (41), and pistons (42).
16. Remove swashplate (43).
17. Remove screws (45), bearings (44), bearing cone (46), and bearing cup (47).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Wed Nov 25 14:25:58 UTC+0800 2020
7/8
2020/11/25

Shutdown SIS
Previous Screen
i07080593
Piston Pump (Implement) - Assemble
SMCS - 5070-016-II; 5084-016-QP
Assembly Procedure
1. Install screws (45), bearings (44), bearing cone (46), and bearing cup (47).
1/6
2020/11/25

2. Install swashplate (43).
3. Install shaft (37).
4. Install plug (36).
5. Install dowel (28).
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Install washer (31), spring (30), and washer (29).
2/6
2020/11/25

7. Use Tooling (A), Tooling (B), and a suitable press to install retaining ring (32) onto barrel
(27).
8. Install pistons (42) into retainer (41) and barrel (27).
9. Install barrel (27).
10. Install shim (26) and bearing cone (25).
3/6
2020/11/25

11. Position plates (40) and plates (38).
12. Install bolts (39).
13. Install piston (22), piston (21), spring (24), gasket (19), port plate (20), and bearing cup
(23).
4/6
2020/11/25

injury.
14. Install bolts (17) and head (18).
injury.
5/6
2020/11/25

15. Install retainer (15), spring (14), rod (13), retainer (12), spool (11), plug (10), and the O-ring
seal. Install plug (16) and the O-ring seal.
16. Install retainer (8), spring (7), retainer (6), spool (5), plug (4), and the O-ring seal. Install
plug (9) and the O-ring seal.
17. Install O-ring seals (3).
18. Install bolts (1) and valve (2).
End By:
a. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Implement) -
Install".
Private Network For SIS Licensees.
Wed Nov 25 14:26:54 UTC+0800 2020
6/6
2020/11/25

Shutdown SIS
Previous Screen
i02878348
Piston Pump (Implement) - Install
SMCS - 5070-012-II; 5084-012-QP
Installation Procedure
Table 1
Required Tools
A 316-1752 Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.
1/6
2020/11/25

2. Install O-ring seal (14). Use Tooling (A) and a suitable lifting device in order to install
piston pump (13). The weight of piston pump (13) is approximately 70 kg (155 lb). Install
bolts (12) .
3. Connect hose assembly (11). Connect tube assembly (10) .
2/6
2020/11/25

4. Connect hose assembly (9) .
3/6
2020/11/25

6. Connect hose assemblies (7) .
7. Connect hose assemblies (6). Turn the fuel supply to the ON position.
8. Install clips (5) .
4/6
2020/11/25

10. Install clips (3) .
11. Install panel (2). Close door (1) .
5/6
2020/11/25

12. Fill the hydraulic tank. Refer to Operation and Maintenance Manual, "Hydraulic System Oil
- Change".
Private Network For SIS Licensees.
Wed Nov 25 14:27:50 UTC+0800 2020
6/6
2020/11/25

Shutdown SIS
Previous Screen
i02902089
Control Manifold (Pilot Shutoff) - Remove
SMCS - 5264-011
Removal Procedure
Table 1
Required Tools
A 311-1362 Vacuum Cap 1
Start By:
A. Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame
Lock - Separate and Connect".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/5
2020/11/25

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered, oil is cool before
removing any components or lines. Remove the oil filler cap only when
the engine is stopped, and the filler cap is cool enough to touch with
your bare hand.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all harness assemblies, and on all tube assemblies for
installation purposes. Plug all tube assemblies. This helps to prevent fluid loss, and this helps to
keep contaminants from entering the system.
1. Release the system pressure. Refer to Operation and Maintenance Manual, "System
Pressure - Release".
2. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A).
Apply 138 kPa (20 psi). This procedure will pull a vacuum on the hydraulic system.
2/5
2020/11/25

3. Remove panel (1) .
4. Disconnect harness assemblies (2) .
3/5
2020/11/25

5. Disconnect hose assembly (3) .
6. Disconnect hose assemblies (4) and (5) .
Rear view of control manifold
7. Remove bolts (6) .
4/5
2020/11/25

Caterpillar Cat 24M Motor Grader (Prefix B93) Service Repair Manual (B9300001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 24M Motor Grader (Prefix B93) Service Repair Manual (B9300001 and up).pdf

Similar to Caterpillar Cat 24M Motor Grader (Prefix B93) Service Repair Manual (B9300001 and up).pdf (11)

More from jdksmmdmdd

More from jdksmmdmdd (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 24M Motor Grader (Prefix B93) Service Repair Manual (B9300001 and up).pdf