The document provides instructions for removing and installing a bucket on a 302CR Mini Hydraulic Excavator. To remove the bucket, lower it to the ground, remove the retainer bolts, and remove the pins connecting the bucket to the linkage and stick. To install the bucket, position the stick over the bucket, insert the pins through the bucket linkage and stick, and install the retainer bolts with two nuts each to lock them in place.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix MY6) Service Repair Ma...udjkskdmmd
The document provides instructions for removing and installing a bucket on a 301.6 Mini Hydraulic Excavator. The removal procedure involves lowering the bucket to the ground, removing retainer bolts, and removing pins from the bucket linkage and stick to detach the bucket. The installation procedure is the reverse of removal, positioning the stick over the bucket and installing pins and retainer bolts.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fikskkdmmd1
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix MY6) Service Repair Ma...yan77xunhao
The document provides instructions for removing and installing a bucket on a 301.6 Mini Hydraulic Excavator. The removal procedure involves lowering the bucket to the ground, removing retainer bolts and pins connecting the bucket to the linkage and stick, and removing the bucket. The installation procedure is the reverse of removal, positioning the stick over the bucket and installing the pins and retainer bolts.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjskekfseik
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fikskkdmmd1
The document provides instructions for disassembling and assembling the boom cylinder of a 301.7CR mini hydraulic excavator. The disassembly procedure involves removing seals and mounting the cylinder in a repair bench tool to access internal components like the piston. Items like seals, bushings, and O-rings are then removed. The assembly procedure reverses these steps, providing details on installing individual parts and tightening to the specified torques. Tools required include a cylinder repair bench, spanner wrenches, and sockets.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...cdfvvv1
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing these components in reverse order and includes torque specifications for tightening fasteners. Removal and installation instructions are also provided for the boom and boom swing cylinder.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fjskekfseik
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing seals and components in the reverse order of disassembly. Tools required include a cylinder repair bench, spanner wrenches, and sockets. Safety precautions are provided regarding hydraulic pressure during disassembly.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix MY6) Service Repair Ma...udjkskdmmd
The document provides instructions for removing and installing a bucket on a 301.6 Mini Hydraulic Excavator. The removal procedure involves lowering the bucket to the ground, removing retainer bolts, and removing pins from the bucket linkage and stick to detach the bucket. The installation procedure is the reverse of removal, positioning the stick over the bucket and installing pins and retainer bolts.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fikskkdmmd1
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar Cat 301.6 Mini Hydraulic Excavator (Prefix MY6) Service Repair Ma...yan77xunhao
The document provides instructions for removing and installing a bucket on a 301.6 Mini Hydraulic Excavator. The removal procedure involves lowering the bucket to the ground, removing retainer bolts and pins connecting the bucket to the linkage and stick, and removing the bucket. The installation procedure is the reverse of removal, positioning the stick over the bucket and installing the pins and retainer bolts.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 301.6 mini hydraulic excavator (prefix my6) service repair ma...fjskekfseik
The document provides instructions for disassembling and assembling a blade cylinder for a 301.6 Mini Hydraulic Excavator. The disassembly procedure involves removing seals and other components from both ends of the cylinder. The assembly procedure describes installing the components in reverse order and applying the appropriate torque to fasteners. Separate sections also describe removing and installing the excavator's blade and bucket.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fikskkdmmd1
The document provides instructions for disassembling and assembling the boom cylinder of a 301.7CR mini hydraulic excavator. The disassembly procedure involves removing seals and mounting the cylinder in a repair bench tool to access internal components like the piston. Items like seals, bushings, and O-rings are then removed. The assembly procedure reverses these steps, providing details on installing individual parts and tightening to the specified torques. Tools required include a cylinder repair bench, spanner wrenches, and sockets.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...cdfvvv1
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing these components in reverse order and includes torque specifications for tightening fasteners. Removal and installation instructions are also provided for the boom and boom swing cylinder.
Caterpillar cat 301.7 cr mini hydraulic excavator (prefix jh7) service repair...fjskekfseik
The document provides instructions for disassembling and assembling the boom cylinder of a Caterpillar 301.7CR Mini Hydraulic Excavator. The disassembly procedure involves removing seals and internal components from both ends of the cylinder. The assembly procedure describes installing seals and components in the reverse order of disassembly. Tools required include a cylinder repair bench, spanner wrenches, and sockets. Safety precautions are provided regarding hydraulic pressure during disassembly.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 302CR MINI HYD EXCAVATOR RHM
Configuration: 302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07362008
Blade Cylinder - Disassemble
SMCS - 7562-015-BG
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 152-4251 Cylinder Repair Bench 1
B 1P-2853 Spanner Wrench 1
C 280-2060 Offset Spanner Wrench 1
D
8H-8539 1 5/8" Socket 1
5P-3588 Adapter 1
Start By:
a. Remove blade cylinder.
1/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g06295269
Illustration 2 g06295274
1. Remove seals (1) from barrel end of blade cylinder (2). Remove seals (3) from rod end of
blade cylinder (4).
Illustration 3 g06295283
2. Mount blade cylinder (5) into Tooling (A).
2/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 4 g06295331
3. Use Tooling (B) to loosen cylinder nut (6).
Illustration 5 g06295371
Illustration 6 g06295383
4. Remove cylinder nut (6) from the barrel. Place support under barrel end of cylinder (5).
3/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 7 g06295398
5. Back the cylinder bench out to remove rod end (9) from the cylinder barrel. Remove set
screw and ball (7) from piston (8).
Illustration 8 g06295422
6. Use Tooling (D) to remove piston (8).
Illustration 9 g06296653
7. Remove cylinder nut (6) from rod end (9).
4/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 10 g06295640
Illustration 11 g06295645
8. Remove bushing (10). Remove outer seal (11), inner seal (12), and O-ring seal (13).
Illustration 12 g06295654
9. Remove O-ring seal and backup ring (14). Remove O-ring seal (15).
5/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 13 g06295667
10. Remove seal (16) and spacer (17).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Mar 5 22:44:05 UTC+0800 2020
6/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 302CR MINI HYD EXCAVATOR RHM
Configuration: 302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07366569
Blade Cylinder - Assemble
SMCS - 7562-016-BG
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 152-4251 Cylinder Repair Bench 1
B 1P-2853 Spanner Wrench 1
C 280-2060 Offset Spanner Wrench 1
D
8H-8539 1 5/8" Socket 1
5P-3588 Adapter 1
Illustration 1 g06295667
1/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. 1. Install seal (16) and spacer (17).
Illustration 2 g06295654
2. Install O-ring seal and backup ring (14). Install O-ring seal (15).
Illustration 3 g06295640
Illustration 4 g06295645
3. Install bushing (10). Install O-ring seal (13). Install inner seal (12), and outer seal (11).
2/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 5 g06296653
4. Install cylinder nut (6) onto rod end (9). Apply oil on seals and rod end for assembly.
Illustration 6 g06295422
Illustration 7 g06295757
5. Mount the rod end onto Tooling (A).
Install piston (8). Use Tooling (D) to tighten piston (8). Tighten piston (8) to a torque of
400 ± 20 N·m (295 ± 15 lb ft).
3/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Install ball and set screw (7). Tighten set screw (7) to a torque of 17 ± 2 N·m
(150 ± 18 lb in). Stake set screw in place once torque is applied.
Illustration 8 g06319794
Illustration 9 g06295798
6. Mount barrel end of cylinder (5) on Tooling (A).
Align barrel assembly (5) and the rod assembly for installation. Apply hydraulic oil inside
barrel assembly and on piston (8).
Install the piston and rod assembly inside the barrel assembly.
4/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 10 g06295383
Illustration 11 g06295820
7. Install cylinder nut (6) into barrel assembly (5). Apply hydraulic oil to seals before
installation.
Use Tooling (C) to tighten cylinder nut (6) to a torque of 226 N·m (167 lb ft).
Illustration 12 g06295269
Illustration 13 g06295274
5/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. 8. Install seals (1) into barrel end of blade cylinder (2). Install seals (3) into rod end of blade
cylinder (4).
End By:
a. Install blade cylinder.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Mar 5 22:45:01 UTC+0800 2020
6/6
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 302CR MINI HYD EXCAVATOR RHM
Configuration: 302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07397606
Blade - Remove and Install
SMCS - 6060-010
Removal Procedure
Start By:
a. Remove blade cylinder
Illustration 1 g06310423
1. Place suitable blocking under blade assembly. Remove bolts (1) and pin assemblies (2).
1/2
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 2 g06310444
Illustration 3 g06310445
2. Attach strap and a suitable lifting device around blade assembly (3). The weight of blade
assembly (3) is approximately 68 kg (150 lb). Remove blade assembly (3).
Installation Procedure
1. Install blade assembly (3) in the reverse order of removal.
End By:
a. Install blade cylinder
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Mar 5 22:45:58 UTC+0800 2020
2/2
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 302CR MINI HYD EXCAVATOR RHM
Configuration: 302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07394729
Bucket - Remove and Install
SMCS - 6001-010; 6101-010
Removal Procedure
1. Lower bucket to the ground.
Illustration 1 g06306012
1. Remove retainer bolts (1).
1/3
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 2 g06306014
2. Remove pins (2) from bucket linkage and stick. Remove bucket (3).
Installation Procedure
Illustration 3 g06306014
1. Position the stick over the bucket (3). Install pins (2) through the bucket linkage and the
stick.
Illustration 4 g06306012
2/3
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 2. Install retainer bolts (1). Place two nuts on the retainer bolts (1) to lock in place.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Mar 5 22:46:55 UTC+0800 2020
3/3
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 302CR MINI HYD EXCAVATOR RHM
Configuration: 302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07390177
Bucket - Remove
SMCS - 6101-011
Removal Procedure
1. Lower bucket to the ground.
Illustration 1 g06306012
1. Remove retainer bolts (1).
1/3
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 2 g06306014
2. Remove pins (2) from bucket linkage and stick. Remove bucket (3).
Installation Procedure
Illustration 3 g06306014
1. Position the stick over the bucket (3). Install pins (2) through the bucket linkage and the
stick.
Illustration 4 g06306012
2/3
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 2. Install retainer bolts (1). Place two nuts on the retainer bolts (1) to lock in place.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Mar 5 22:47:52 UTC+0800 2020
3/3
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
23. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 302CR MINI HYD EXCAVATOR RHM
Configuration: 302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1 Engine
Disassembly and Assembly
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems
Media Number -M0092231-00 Publication Date -01/09/2018 Date Updated -11/09/2018
i07394736
Bucket Linkage - Remove and Install
SMCS - 6513-010
Removal Procedure
Start By:
a. Remove Bucket
Illustration 1 g06306848
1. Remove retainer bolts (1).
1/3
302 CR Mini Hydraulic Excavator RHM00001-UP (MACHINE) POWERED BY C1.1...
2020/3/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...