This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts including the cover, carrier assembly, planetary gears, ring gear, and pinion shaft. The assembly procedure describes installing these parts in reverse order and includes cleaning, lubricating, and setting components like retaining rings, springs, and seals. Precautions are listed for lifting heavy parts safely and ensuring clean mating surfaces during reassembly.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for disassembling and assembling the front axle components of an M318C Wheeled Excavator, including:
1. Removing components like the carrier housing, planetary gears, brake discs, and hub assembly which involve using various tools and lifting devices.
2. Disassembling internal components of the carrier like retaining rings, bearings, and seals.
3. Cleaning all parts before assembly and heating/cooling some components to aid installation.
4. Reassembling the components in reverse order, applying grease and torquing fasteners to specifications. Proper cleanliness and procedure is emphasized for the precision components.
Caterpillar cat 330 d fm excavator (prefix h3k) service repair manual (h3k000...jfdskekdmme
This document provides disassembly instructions for the final drive of a 330D FM excavator. It lists over 40 steps to completely disassemble the final drive and its components. This includes removing the travel motor, draining fluids, removing sprockets, planetary gear assemblies, carrier assemblies, discs, plates, springs, and other parts. Detailed illustrations are provided to identify each component. Special tools are required to remove retaining rings, bearings, and other secured pieces.
Caterpillar cat 330 b excavator (prefix 2rr) service repair manual (2rr00001 ...hfjsekekmmd
This document provides instructions for removing and reassembling the final drives on an excavator model 330B. The summary is:
1. The final drive is disassembled by removing components like the ring gear, carrier assemblies, planetary gears, and seals.
2. To reassemble, components are cleaned and seals/bearings installed before refitting parts like the carrier assemblies, ring gear and sprockets.
3. Precise measurements are taken to determine the correct shim thickness for installing the gear to achieve proper bearing preload.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for separating the upper frame and undercarriage frame on an M318C wheeled excavator. It lists the required tools which include electric hydraulic pumps, cylinders, stands, pins, tubes, collars, saddles, links and guide bolts. The procedure involves using the listed tools and hydraulic jacks to lift and support the frames while removing connecting components. Proper containment of fluids is noted as important during the separation process.
Caterpillar cat 312 c l excavator (prefix cbt) service repair manual (cbt0000...fksjksmmde
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in multiple steps to fully disassemble the swing drive. These parts include gears, shafts, bearings, seals, and housings. The assembly section then lists the parts and tools needed and describes the reverse process of installing the components in the proper order and applying sealants or fasteners as needed.
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves removing over 30 individual components in a specific sequence. This includes removing gears, shafts, bearings, seals, and housing components. The assembly process reverses the disassembly steps and provides details on cleaning, lubricating, and setting proper bearing preloads using shims. Special tools are required for tasks like installing dual-cone seals.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for disassembling and assembling the front axle components of an M318C Wheeled Excavator, including:
1. Removing components like the carrier housing, planetary gears, brake discs, and hub assembly which involve using various tools and lifting devices.
2. Disassembling internal components of the carrier like retaining rings, bearings, and seals.
3. Cleaning all parts before assembly and heating/cooling some components to aid installation.
4. Reassembling the components in reverse order, applying grease and torquing fasteners to specifications. Proper cleanliness and procedure is emphasized for the precision components.
Caterpillar cat 330 d fm excavator (prefix h3k) service repair manual (h3k000...jfdskekdmme
This document provides disassembly instructions for the final drive of a 330D FM excavator. It lists over 40 steps to completely disassemble the final drive and its components. This includes removing the travel motor, draining fluids, removing sprockets, planetary gear assemblies, carrier assemblies, discs, plates, springs, and other parts. Detailed illustrations are provided to identify each component. Special tools are required to remove retaining rings, bearings, and other secured pieces.
Caterpillar cat 330 b excavator (prefix 2rr) service repair manual (2rr00001 ...hfjsekekmmd
This document provides instructions for removing and reassembling the final drives on an excavator model 330B. The summary is:
1. The final drive is disassembled by removing components like the ring gear, carrier assemblies, planetary gears, and seals.
2. To reassemble, components are cleaned and seals/bearings installed before refitting parts like the carrier assemblies, ring gear and sprockets.
3. Precise measurements are taken to determine the correct shim thickness for installing the gear to achieve proper bearing preload.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for separating the upper frame and undercarriage frame on an M318C wheeled excavator. It lists the required tools which include electric hydraulic pumps, cylinders, stands, pins, tubes, collars, saddles, links and guide bolts. The procedure involves using the listed tools and hydraulic jacks to lift and support the frames while removing connecting components. Proper containment of fluids is noted as important during the separation process.
Caterpillar cat 312 c l excavator (prefix cbt) service repair manual (cbt0000...fksjksmmde
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in multiple steps to fully disassemble the swing drive. These parts include gears, shafts, bearings, seals, and housings. The assembly section then lists the parts and tools needed and describes the reverse process of installing the components in the proper order and applying sealants or fasteners as needed.
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves removing over 30 individual components in a specific sequence. This includes removing gears, shafts, bearings, seals, and housing components. The assembly process reverses the disassembly steps and provides details on cleaning, lubricating, and setting proper bearing preloads using shims. Special tools are required for tasks like installing dual-cone seals.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Hyster p177 (h3.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes lifting capacities, counterweight weights, tire sizes, fuel and fluid capacities, and electrical specifications for various Hyster truck models. It also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h3.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster n006 (h8.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts9) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake and hydraulic lines
Hyster n006 (h7.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h6.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake lines
Hyster l006 (h7.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities, weights, tire sizes, fuel and fluid capacities
- Engine oil, coolant, transmission oil, hydraulic oil, brake fluid specifications
- Electrical system components and specifications
- Transmission oil pressures
- Hydraulic and steering system relief pressures and components
- Instructions for removing the drive axle assembly, including draining fluids and disconnecting brake, cooling, and drive shaft components.
Hyster l006 (h6.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities and weights for each model
- Tire sizes, fuel capacities, fluid capacities and specifications for various systems
- Transmission oil pressures and relief pressures for hydraulic and steering systems
- Procedures for removing the drive axle, including draining fluids and disconnecting brake, cooling and driveline components.
Hyster k019 (h16 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h14 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h13 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM and H6-H7XM-12EC units.
Hyster k019 (h10 xm 12 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h7 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h6 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM lift trucks.
Hyster k007 (h12 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xms 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster p177 (h3.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes lifting capacities, counterweight weights, tire sizes, fuel and fluid capacities, and electrical specifications for various Hyster truck models. It also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h3.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster n006 (h8.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts9) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake and hydraulic lines
Hyster n006 (h7.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h6.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake lines
Hyster l006 (h7.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities, weights, tire sizes, fuel and fluid capacities
- Engine oil, coolant, transmission oil, hydraulic oil, brake fluid specifications
- Electrical system components and specifications
- Transmission oil pressures
- Hydraulic and steering system relief pressures and components
- Instructions for removing the drive axle assembly, including draining fluids and disconnecting brake, cooling, and drive shaft components.
Hyster l006 (h6.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities and weights for each model
- Tire sizes, fuel capacities, fluid capacities and specifications for various systems
- Transmission oil pressures and relief pressures for hydraulic and steering systems
- Procedures for removing the drive axle, including draining fluids and disconnecting brake, cooling and driveline components.
Hyster k019 (h16 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h14 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h13 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM and H6-H7XM-12EC units.
Hyster k019 (h10 xm 12 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h7 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h6 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM lift trucks.
Hyster k007 (h12 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xms 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D EXCAVATOR EAH
Configuration: 330D & 330D L Excavators EAH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i06560081
Swing Drive - Disassemble
SMCS - 5459-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 1U-8221 Nylon Sling 1
C 5P-5197 Pliers 1
Start By:
a. Remove the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove"
.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
1/8(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00518369
1. Position the swing drive on suitable cribbing, as shown. The weight of the swing drive is
approximately 281 kg (620 lb).
2. Put an alignment mark on the cover and the housing of the swing drive for assembly
purposes.
3. Remove bolts (1) and cover (2).
4. Install Tooling (A) to cover (2).
Illustration 2 g00518372
5. Use a suitable lifting device and Tooling (A) to remove cover (2) from the ring gear of the
swing drive.
2/8(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00518397
6. Use two people to remove carrier assembly (3). The weight of the carrier assembly is
approximately 23 kg (50 lb).
7. Use the following procedure to disassemble carrier assembly (3).
Illustration 4 g00518398
Illustration 5 g00518400
a. Remove sun gear (4) from carrier assembly (3).
b. Drive spring pin (6) into planetary shaft (5) with a hammer and a punch.
3/8(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. c. Remove planetary shaft (5), thrust washers (9), and planetary gear (7) from the carrier
assembly.
d. Remove bearing (8) from planetary gear (7).
e. Remove spring pin (6) from planetary shaft (5) with a hammer and a punch.
f. Repeat Steps 7.a through 7.e to remove the other three planetary gears from the
carrier assembly.
Illustration 6 g00518543
g. Remove retaining ring (10) with a screwdriver. Remove gear (11) from carrier (3).
Illustration 7 g00518549
h. Remove retaining ring (12) from gear (11).
4/8(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 8 g00518551
8. Remove retaining ring (15) that holds carrier assembly (13) in position.
9. Remove spacer (14) from carrier assembly (13).
Illustration 9 g00518552
10. Slide a piece of steel bar stock between the planetary gears in carrier assembly (13), as
shown. Make sure that the steel bar stock is centered in the carrier assembly. Fasten Tooling
(B) and a suitable lifting device to the steel bar stock, as shown. Slowly lift carrier assembly
(13) from the swing drive housing. The weight of carrier assembly (13) is approximately
39 kg (86 lb).
11. Use the following procedure to disassemble carrier assembly (13).
5/8(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 10 g00518553
Illustration 11 g00518555
a. Drive spring pin (16) into planetary shaft (17) with a hammer and a punch.
b. Remove planetary shaft (17), thrust washers (20), and planetary gear (18) from the
carrier assembly.
c. Remove bearings (19) from planetary gear (18).
d. Remove spring pin (16) from planetary shaft (17) with a hammer and a punch.
e. Repeat Steps 11.a through 11.d to remove the other three planetary gears from the
carrier assembly.
Illustration 12 g00518581
12. Use two people to remove ring gear (21) from the swing drive housing. The weight of the
ring gear is approximately 39 kg (86 lb).
6/8(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 13 g00518589
13. Use Tooling (C) to remove retaining ring (22).
Illustration 14 g00518595
14. Loosen, but do not remove bolts (23) that secure cage (24) to the swing drive housing.
Illustration 15 g00518604
7/8(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 16 g03774521
15. Place swing drive housing (25) in a suitable press, as shown. The combined weight of the
swing drive housing (25), the pinion shaft (28) and the bearing cage (24) is approximately
136 kg (300 lb).
16. Place suitable cribbing directly under the pinion shaft to prevent pinion shaft (28) from
falling when cage (24) is pressed out of the swing drive housing.
17. Remove and discard bolts (23) that secure cage (24) to the swing drive housing. Carefully
press cage (24) and pinion shaft (28) as a unit out of swing drive housing (25). Discard
pinion shaft (28), cage (24), bearing (29), sleeve (27), and bearing (26) as an assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 27 17:28:09 UTC+0800 2020
8/8(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D EXCAVATOR EAH
Configuration: 330D & 330D L Excavators EAH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i06939513
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-5197 Pliers 1
B 138-7574 Link Brackets 2
C 138-7575 Link Bracket 3
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 1 g00869899
1. Install lip seals (32) and O-ring seal (33) in bearing cage (29).
Illustration 2 g00870134
Note: Lubricate the seals and the seal surface of the shaft before you install the cage
assembly.
2. Carefully install cage (29) on shaft (31).
Illustration 3 g00870142
3. Raise the temperature of bearing (36) to 135 °C (275 °F) and use two people to install the
bearing on shaft (31). The weight of bearing (36) is approximately 35 kg (77 lb).
4. Install spacer (35) on shaft assembly (31). Install the spacer with relief against bearing (36).
2/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 4 g00870160
5. Raise the temperature of bearing (34) to 135 °C (275 °F). Install the bearing on shaft (31)
and against spacer (35).
Illustration 5 g00870169
6. Use Tooling (A) to install retaining ring (28) on shaft (31) and against bearing (34).
Illustration 6 g01041406
7. Install shaft assembly (31) in swing drive housing (16).
3/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. a. Apply 5P-3931 Anti-Seize Compound on the inside diameter of swing drive housing
(16).
b. Lower the temperature of shaft assembly (31).
c. Attach Tooling (C) and a suitable lifting device to the shaft assembly.
d. Install the shaft assembly into swing drive housing (16). Bearing (34) must be within
the bore of the swing drive housing.
e. Remove Tooling (C) and the suitable lifting device from the shaft assembly. Attach
Tooling (C) and the suitable lifting device to the swing drive housing.
f. Lift the swing drive vertically. Use a hammer and a drift to align bearing (34) in the
lower bore of the swing drive housing. When the bearing is properly aligned in the
bore, shaft assembly (31) will drop into the proper position within the swing drive
housing.
Illustration 7 g00870264
8. Apply 1U-8846 Sealant on the threads of bolts (30).
9. Install bolts (30) and washers in bearing cage (29) and swing drive housing (16).
Illustration 8 g00869483
4/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 9 g00870281
10. Install bearings (24) and (26) in gear (25).
11. Install gear (25) and washers (23) and (27) in carrier (20).
12. Lower the temperature of shaft (22). Install the shaft in carrier assembly (20).
13. Install pin (21) in the carrier assembly and the shaft.
14. Use a hammer and a center punch to stake the pin in the carrier housing.
15. Repeat Steps 10 through Steps 14 on the remaining gear assemblies.
Illustration 10 g00869464
16. Use a suitable lifting device to install carrier assembly (20). The weight of carrier assembly
(20) is approximately 68 kg (150 lb).
5/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 11 g00869460
17. Install retaining ring (19).
Illustration 12 g00869406
18. Install spacer (17) in carrier assembly (18).
Illustration 13 g00869390
19. Make sure that the mating surfaces of ring gear (15) and swing drive housing (16) are
thoroughly clean.
6/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 20. Apply 1U-8846 Gasket Sealant to the face of swing drive housing (16) and the face of ring
gear (15).
21. Use Tooling (B) and a suitable lifting device to install ring gear (15) in swing drive housing
(16). The weight of ring gear (15) is approximately 80 kg (175 lb).
Illustration 14 g00869383
22. Install retaining ring (14) into the sun gear.
Illustration 15 g00869377
23. Install sun gear (13) in carrier assembly (4). Install upper retaining ring (12).
24. Assemble carrier assembly (4).
7/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 16 g00869315
a. Apply clean SAE 30W oil on bearing (10). Install bearing (10) in planetary gear (9).
b. Install thrust washer (8) on one side of planetary gear (9).
c. Install thrust washer (11) on the other side of planetary gear (9).
d. Use a deburring tool to remove the metal burr from the openings in the carrier.
e. Install planetary gear (9) and the thrust washers in carrier assembly (4).
Illustration 17 g00869309
f. Install planetary shaft (7) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
Illustration 18 g00703700
8/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. g. Drive spring pin (6) into shaft (7). Orient the split in spring pin (6) vertically to the
carrier. Align the split in the spring pin to the top or the bottom. Make a stake mark
on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 24.a through 24.g to install the other three planetary gears in the carrier.
Illustration 19 g00869294
25. Use two people to install carrier assembly (4) in the ring gear. The weight of the carrier
assembly is approximately 36 kg (80 lb).
26. Install spacer (5) in carrier assembly (4).
Illustration 20 g00869281
27. Install sun gear (3) in carrier assembly (4).
9/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 21 g00869266
28. Make sure that the mating surfaces of the ring gear and cover (2) are thoroughly clean.
29. Apply 1U-8846 Gasket Sealant on the flange surface of the ring gear and cover (5).
30. Install cover (2) and bolts (1).
End By:
a. Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 27 17:29:12 UTC+0800 2020
10/10(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D EXCAVATOR EAH
Configuration: 330D & 330D L Excavators EAH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07192381
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
132-8223 110 volt Power Pack 1
1U-6221 Torque Wrench 1
132-8143 36 mm Hex Link 1
B 439-3939 Link Bracket As 4
C -
Forcing Bolt
M24 x 3 by 5 inch
2
D - Loctite C5A Copper Anti-Seize -
E 1U-8846 Gasket Sealant 1
1. Apply Tooling (D) on the locating pin and the pin bore in the main frame. Apply Tooling
(E) on the mating surface of the main frame and the swing drive housing.
1/3(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g00875735
2. Attach Tooling (B) and a suitable lifting device to swing drive (2), as shown. The weight of
swing drive (2) is approximately 510 kg (1125 lb). Install swing drive (2) into the original
position. Be careful not to damage the pinion gear.
Note: During installation, the locating pin for the swing drive can come out of the swing
drive housing. The locating pin can be installed with a hammer after the swing drive is in
place.
Illustration 2 g01206242
3. Use Tooling (A) to install bolts (1) that secure the swing drive to the main frame.
4. Before assembly, remove compound, oil, and dust from female threads, then apply Tooling
(D) to the threads of bolts (1).
5. Tighten bolts (1) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
6. Fill the swing drive with oil. Refer to Operation and Maintenance Manual, "Swing Drive Oil
- Change".
End By:
2/3(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. a. Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install"
.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 27 17:30:14 UTC+0800 2020
3/3(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D EXCAVATOR EAH
Configuration: 330D & 330D L Excavators EAH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02386587
Swing Gear and Bearing - Remove
SMCS - 7063-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7576 Link Bracket 4
B
132-8223 Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase)(1)
1
1U-6221 Hydraulic Torque Wrench 1
132-8143 36 mm Hex Link 1
(1)
132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available.
Start By:
a. Remove the undercarriage frame. Refer to Disassembly and Assembly, "Upper Frame and
Undercarriage Frame - Separate".
1. Remove all of the grease from the swing gear and bearing. Put the grease in a suitable
container for storage or disposal.
1/3(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 1 g00520664
2. Put an alignment mark on swing gear and bearing (1) and on the undercarriage frame
assembly for assembly purposes. Attach Tooling (A) and a suitable lifting device to swing
gear and bearing (1), as shown. Apply slight lifting tension to the swing gear and bearing.
Illustration 2 g00520670
3. Use Tooling (B) in order to remove bolts (2) and the spacers that hold swing gear and
bearing (1) to the undercarriage frame.
4. Remove swing gear and bearing (1). The weight of the swing gear and bearing (1) is
approximately 280 kg (615 lb).
2/3(W)
w
2020/8/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...