Caterpillar cat d8 r track type tractor dozer bulldozer (prefix jr8) service repair manual (jr800001 and up)

Service Repair Manual
Models
D8R TRACK-TYPE TRACTOR
Dozer Bulldozer

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8R TRACK-TYPE TRACTOR JR8
Configuration: D8R TRACK-TYPE TRACTOR JR800001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
D8R and D8T Track-Type Tractor Power Train
Media Number -M0076745-02 Publication Date -01/03/2018 Date Updated -12/03/2018
i05353222
Steering Planetary and Brake - Disassemble
SMCS - 4132-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 439-3940 Link Brackets 3
B 5J-0490 Bolts (1/2 - 13) 3
C 1P-0520 Driver Gp 1
Start By:
a. Remove the right hand final drive, the planetary group, and the brake.
Note: Orientation of brake and planetary assemblies. Mark the top of the planetary gears, the sun
gear, and the ring gear (if equipped) for assembly purposes.
1/10D8R TRACK-TYPE TRACTOR JR800001-UP (MACHINE) POWERED BY C15 En...
2020/1/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g03390771

1. Position final drive (3), the planetary group, and brake hub (2) as shown in Illustration 3.
2. Remove two bolts (1) that hold the planetary group and brake hub (2) to final drive (3).
3. Install Tooling (B) in the hub of final drive (3).
4. Tighten Tooling (B) evenly to remove the planetary group and brake hub (1) from final
drive (3).
5. Attach Tooling (A) and a suitable lifting device to the planetary group and brake hub (2).
The weight of the planetary group and brake hub (2) is approximately 136 kg (300 lb).

Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
6. Remove bolts (4).
7. Remove brake hub (2) from housing (6).
8. Remove the retaining ring and ring gear (5) from brake hub (2).
9. Remove four friction discs (7) and three brake plates from housing (6).

10. Remove bolts (8) and plate (9).
Note: Do not allow carrier (11) to fall when carrier (11) is pressed from housing (6).
11. Use a suitable press and Tooling (C) to remove carrier (11) from housing (6).
12. Remove bearing cone (10) from housing (6).
13. Remove ring (14) from carrier (11).
15. Remove slinger (12) from carrier (11).
Note: Damage to bearing cone (15) will result if removed from carrier (11).
16. If necessary, remove bearing cone (15) from carrier (11).

17. Use a hammer and a punch to push pin (17) in shaft (16).
18. Remove planetary shaft (16), planetary gear (19), thrust discs (20), and bearings (21) from
carrier (11).
19. Remove pin (17) from planetary shaft (16).
20. Repeat Steps 17 through 19 for remaining planetary gears (19).
21. Remove sun gear (18) from carrier (11).

Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
23. Remove retainer (23) from piston (24).
24. If necessary, remove bearing cups (25) from retainer (23).
25. Remove seal ring (26) from retainer (23).

26. Remove piston (24) and O-ring seal (27) from the housing.
27. Remove seal ring (28) from piston (24).
28. Inspect the O-ring seals.
29. If necessary, replace the O-ring seals.
30. Remove spring (30) and ring (31) from housing (6).

31. Remove shuttle valve (32) from the housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jan 26 22:47:28 UTC+0800 2020
10/10D8R TRACK-TYPE TRACTOR JR800001-UP (MACHINE) POWERED BY C15 ...

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8R TRACK-TYPE TRACTOR JR8
Configuration: D8R TRACK-TYPE TRACTOR JR800001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
D8R and D8T Track-Type Tractor Power Train
Media Number -M0076745-02 Publication Date -01/03/2018 Date Updated -12/03/2018
i05353533
Steering Planetary and Brake - Assemble
SMCS - 4132-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 439-3940 Link Brackets 3
D - Loctite Hi-Temp Flange Sealant 1
1. Install shuttle valve (32) in the housing.

Note: Orient spring (30) with the outer edge downward.
2. Install ring (31) and spring (30) in housing (6).
3. Apply clean oil to seal ring (28).
Note: Orient the seal ring (28) with the lip downward as shown in Illustration 3.
4. Install seal ring (28) in piston (24).

5. Install piston (24) and O-ring seal (27) in the housing.
6. Lower the temperature of bearing cups (25). Install bearing cups (25) in retainer (23).
Note: Orient seal ring (26) with the lip downward as shown in Illustration 5.
7. Install seal ring (26) in retainer (23). Apply clean oil to seal ring (26).
8. Install retainer (23) on piston (24). Align the oil passage in retainer (23) with the oil passage
and the O-ring seal in the housing. Install bolts (22).

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

9. Install sun gear (18) in carrier (11).
10. Install bearings (21) in planetary gear (19).
11. Install thrust discs (20) and planetary gear (19) in carrier (11). Install planetary shaft (16).
Note: If the rubber in pin (17) is damaged, replace pin (17).
12. Align the hole in planetary shaft (16) with the hole in carrier (11) and install pin (17). Install
pin (17) until the pin is even with the surface of carrier (11).
13. Repeat Steps 10 through 12 for the remaining planetary gears.
Note: If bearing cone (15) was removed from planetary carrier (11), then a new bearing
cone (15) must be installed.
14. Raise the temperature of bearing cone (15) to a maximum of 135 °C (275 °F). Install
bearing cone (15) on carrier (11).
15. Apply Tooling (D) to the flange of slinger (12).
16. Install slinger (12) on carrier (11). Install bolts (13).

17. Install ring (14) in carrier (11).
18. Position housing (6) on carrier (11).
19. Raise the temperature of bearing cone (10) to a maximum of 135 °C (275 °F). Install
bearing cone (10) on carrier (11).
20. Position plate (9) on the carrier.
21. Install bolts (8).

22. Install four friction discs (7) and the three brake plates into housing (6). Alternate friction
discs (7) and the brake plates.

23. Install ring gear (5) and the retaining ring in brake hub (2).
24. Position brake hub (5) on housing (6).
25. Install bolts (3).

Caterpillar cat d8 r track type tractor dozer bulldozer (prefix jr8) service repair manual (jr800001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (8)

Similar to Caterpillar cat d8 r track type tractor dozer bulldozer (prefix jr8) service repair manual (jr800001 and up)

Similar to Caterpillar cat d8 r track type tractor dozer bulldozer (prefix jr8) service repair manual (jr800001 and up) (7)

More from fujskekrtfksmem

More from fujskekrtfksmem (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat d8 r track type tractor dozer bulldozer (prefix jr8) service repair manual (jr800001 and up)