This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
Caterpillar cat 322 l excavator (prefix 9rl) service repair manual (9rl00001 ...ujfjjskkemm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a 322L excavator with a 3116 engine. The removal procedure involves disconnecting linkages, removing clips and pins connecting the governor. New seals are installed during reassembly. Special tools are required to compress springs and install pins. The installation procedure specifies tightening bolts in a certain sequence and adjusting the control rod for free rotation.
Caterpillar cat 325 c excavator (prefix crb) service repair manual (crb00001 ...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 6dn) service repair manual (6dn00001 ...fjsjjekdkme
This service repair manual provides instructions for removing and installing inlet manifolds, valves, and valve guides on Caterpillar 325B and 325B LN excavator engines. The document outlines the required tools and safety procedures, and provides step-by-step instructions with illustrations for each repair procedure. Technicians are advised to keep parts clean, contain fluids properly, and refer to other documents for guidance on reusable components.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 325 b l excavator (prefix 1hs) service repair manual (1hs0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor of a 325B L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then describes 26 steps for reassembling the travel motor, providing details on cleaning, lubricating and properly installing each part in the reverse order of disassembly. Safety notices are included to handle fluids properly and avoid damaging components.
Caterpillar cat 322 l excavator (prefix 9rl) service repair manual (9rl00001 ...ujfjjskkemm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a 322L excavator with a 3116 engine. The removal procedure involves disconnecting linkages, removing clips and pins connecting the governor. New seals are installed during reassembly. Special tools are required to compress springs and install pins. The installation procedure specifies tightening bolts in a certain sequence and adjusting the control rod for free rotation.
Caterpillar cat 325 c excavator (prefix crb) service repair manual (crb00001 ...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 6dn) service repair manual (6dn00001 ...fjsjjekdkme
This service repair manual provides instructions for removing and installing inlet manifolds, valves, and valve guides on Caterpillar 325B and 325B LN excavator engines. The document outlines the required tools and safety procedures, and provides step-by-step instructions with illustrations for each repair procedure. Technicians are advised to keep parts clean, contain fluids properly, and refer to other documents for guidance on reusable components.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 325 b l excavator (prefix 1hs) service repair manual (1hs0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor of a 325B L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then describes 26 steps for reassembling the travel motor, providing details on cleaning, lubricating and properly installing each part in the reverse order of disassembly. Safety notices are included to handle fluids properly and avoid damaging components.
Kawasaki 80 z7 wheel loader service repair manual (serial no. 80c6 5001 and up)fjsjjekdkme
This document provides guidelines and precautions for disassembling and assembling components of a wheel loader. It discusses preparing the work area, marking parts for reassembly, cleaning and inspecting components, applying lubricants, and properly tightening bolts and nuts. Proper maintenance following these guidelines helps prevent damage and ensures safe and efficient reassembly.
Caterpillar cat 325 d fm excavator (prefix c8l) service repair manual (c8l000...fjjskekdmme
This document provides instructions for removing and installing the camshaft and related components on a Caterpillar C7 engine. It describes:
1. Removing the camshaft by first removing other components like the vibration damper, pulley, rocker arms and pushrods.
2. Removing the camshaft gear by pressing it off the camshaft and removing any keys.
3. Removing the camshaft bearings using a special tool, noting the oil hole orientations.
4. Installing the camshaft bearings and gear, aligning oil holes and keys before reinstalling the camshaft.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 3064 or 3066 engine. It includes illustrations and steps to remove the threaded plug and shim that contain the valve from the cylinder block. Proper cleaning and containment of fluids is emphasized. The summary is completed in 3 sentences or less.
Caterpillar cat 320 track type excavator (prefix 7 wk) service repair manual ...cdfzxs
This document provides instructions for servicing components of a 320/320L track-type excavator powered by a 3116 engine, including:
1) Installing the crankshaft rear seal and sleeve using a special tooling set.
2) Removing and installing the crankshaft rear seal carrier using gasket sealant and thread lock compound.
3) Removing and installing the flywheel housing using link brackets and gasket sealant.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure, and marks should be made on lines and cylinders before removal.
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)fjsjjekdkme
The document contains sections from a shop manual for a wheel loader. It includes sections on general information, component layout, specifications, and maintenance procedures. The component layout sections describe and illustrate the main components of the wheel loader including the engine, hydraulic system, electrical system, cab, drive unit, and other key components. The specifications section lists technical specifications for the engine, operating weights, dimensions, travel speeds and other performance specifications.
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
Caterpillar cat 325 l excavator (prefix 2 sl) service repair manual (2sl00001...hfjsekekmmd
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
Caterpillar cat 325 l excavator (prefix 2 sl) service repair manual (2sl00001...jdfjskekmdme
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
Caterpillar cat 325 l excavator (prefix 2 sl) service repair manual (2sl00001...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
Kawasaki 70 z7 wheel loader service repair manual (serial no. 70c6 5001 and up)fujsekksmem
This document provides instructions for disassembling and reassembling a wheel loader. It contains safety precautions and procedures for disassembly, cleaning, inspection, assembly, bleeding air from systems, and releasing pressures. The document is divided into sections covering general information, maintenance standards, specific components of the body, travel system, front attachment, and technical content for disassembly and reassembly. Precautions are provided for using tools safely and properly handling components like seals, slings, and pressures systems to prevent damage and ensure correct reassembly.
Kawasaki 70 z6 wheel loader service repair manual (serial no. 70c7 0101 and up)fujsekksmem
This document contains shop manuals for the Kawasaki 70Z6 wheel loader. It includes information on the machine's specifications, components, systems, operation, maintenance standards, and disassembly and reassembly procedures. The manuals cover the machine's general information, functions and structure, operational performance testing, troubleshooting, and disassembly and reassembly. They are intended to provide technical information and service procedures for experienced technicians working on the 70Z6 wheel loader.
This document is an operation and maintenance manual for Hitachi wheel loaders models 70Z6 and 80Z6 powered by Cummins QSB6.7 engines. It contains sections on safety, components, operation, maintenance, transportation, and specifications. The safety section emphasizes safe work practices including wearing protective equipment, inspecting the machine, avoiding tipping or overloading, and securing the machine for transport. The components section describes the controls, indicators, and features of the operator's cab. The operation section provides instructions for starting, driving, and using the machine. The maintenance section outlines inspection schedules, fluid changes, and service procedures.
This document is an operation and maintenance manual for Hitachi wheel loaders models 70Z6 and 80Z6, powered by Cummins QSB6.7 engines. It contains sections on safety procedures, component identification, operation instructions, maintenance, troubleshooting, specifications, and other technical information for servicing the machines. Safety is the primary focus, with multiple pages outlining hazards and required precautions to prevent injury when operating or working on the loaders.
Kawasaki 80 z7 wheel loader service repair manual (serial no. 80c6 5001 and up)fjsjjekdkme
This document provides guidelines and precautions for disassembling and assembling components of a wheel loader. It discusses preparing the work area, marking parts for reassembly, cleaning and inspecting components, applying lubricants, and properly tightening bolts and nuts. Proper maintenance following these guidelines helps prevent damage and ensures safe and efficient reassembly.
Caterpillar cat 325 d fm excavator (prefix c8l) service repair manual (c8l000...fjjskekdmme
This document provides instructions for removing and installing the camshaft and related components on a Caterpillar C7 engine. It describes:
1. Removing the camshaft by first removing other components like the vibration damper, pulley, rocker arms and pushrods.
2. Removing the camshaft gear by pressing it off the camshaft and removing any keys.
3. Removing the camshaft bearings using a special tool, noting the oil hole orientations.
4. Installing the camshaft bearings and gear, aligning oil holes and keys before reinstalling the camshaft.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 3064 or 3066 engine. It includes illustrations and steps to remove the threaded plug and shim that contain the valve from the cylinder block. Proper cleaning and containment of fluids is emphasized. The summary is completed in 3 sentences or less.
Caterpillar cat 320 track type excavator (prefix 7 wk) service repair manual ...cdfzxs
This document provides instructions for servicing components of a 320/320L track-type excavator powered by a 3116 engine, including:
1) Installing the crankshaft rear seal and sleeve using a special tooling set.
2) Removing and installing the crankshaft rear seal carrier using gasket sealant and thread lock compound.
3) Removing and installing the flywheel housing using link brackets and gasket sealant.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure, and marks should be made on lines and cylinders before removal.
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)fjsjjekdkme
The document contains sections from a shop manual for a wheel loader. It includes sections on general information, component layout, specifications, and maintenance procedures. The component layout sections describe and illustrate the main components of the wheel loader including the engine, hydraulic system, electrical system, cab, drive unit, and other key components. The specifications section lists technical specifications for the engine, operating weights, dimensions, travel speeds and other performance specifications.
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
Caterpillar cat 325 l excavator (prefix 2 sl) service repair manual (2sl00001...hfjsekekmmd
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
Caterpillar cat 325 l excavator (prefix 2 sl) service repair manual (2sl00001...jdfjskekmdme
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
Caterpillar cat 325 l excavator (prefix 2 sl) service repair manual (2sl00001...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
Similar to Caterpillar cat 325 a excavator (prefix 9 zk) service repair manual (9zk00001 and up) (11)
Kawasaki 70 z7 wheel loader service repair manual (serial no. 70c6 5001 and up)fujsekksmem
This document provides instructions for disassembling and reassembling a wheel loader. It contains safety precautions and procedures for disassembly, cleaning, inspection, assembly, bleeding air from systems, and releasing pressures. The document is divided into sections covering general information, maintenance standards, specific components of the body, travel system, front attachment, and technical content for disassembly and reassembly. Precautions are provided for using tools safely and properly handling components like seals, slings, and pressures systems to prevent damage and ensure correct reassembly.
Kawasaki 70 z6 wheel loader service repair manual (serial no. 70c7 0101 and up)fujsekksmem
This document contains shop manuals for the Kawasaki 70Z6 wheel loader. It includes information on the machine's specifications, components, systems, operation, maintenance standards, and disassembly and reassembly procedures. The manuals cover the machine's general information, functions and structure, operational performance testing, troubleshooting, and disassembly and reassembly. They are intended to provide technical information and service procedures for experienced technicians working on the 70Z6 wheel loader.
This document is an operation and maintenance manual for Hitachi wheel loaders models 70Z6 and 80Z6 powered by Cummins QSB6.7 engines. It contains sections on safety, components, operation, maintenance, transportation, and specifications. The safety section emphasizes safe work practices including wearing protective equipment, inspecting the machine, avoiding tipping or overloading, and securing the machine for transport. The components section describes the controls, indicators, and features of the operator's cab. The operation section provides instructions for starting, driving, and using the machine. The maintenance section outlines inspection schedules, fluid changes, and service procedures.
This document is an operation and maintenance manual for Hitachi wheel loaders models 70Z6 and 80Z6, powered by Cummins QSB6.7 engines. It contains sections on safety procedures, component identification, operation instructions, maintenance, troubleshooting, specifications, and other technical information for servicing the machines. Safety is the primary focus, with multiple pages outlining hazards and required precautions to prevent injury when operating or working on the loaders.
Kawasaki 70 tm7 wheel loader service repair manual (serial no. 70c6 5001 and up)fujsekksmem
This document provides instructions for disassembling and reassembling a wheel loader. It contains safety precautions and procedures for disassembly, cleaning, inspection, assembly, bleeding air from systems, and releasing pressures. The document is divided into sections covering general information, maintenance standards, specific components of the body, travel system, front attachment, and their groups. Precautions are given for tasks like using floating seals, nylon slings, cleaning, applying lubricants, and ensuring no tools are left inside after reassembly.
Kawasaki 67 z7b wheel loader service repair manual (serial no. 65c5 5001 and up)fujsekksmem
This document is a shop manual that provides specifications, component layout diagrams, and descriptions for a wheel loader. It includes sections on general information, system components, and operation of individual components. The manual aims to provide technical information for maintenance and repair of the machine.
This document is a parts catalog for a wheel loader powered by a Cummins QSB4.5 engine. It contains over 100 pages listing parts organized into sections for periodic replacement parts, engine, cooling device, air intake device, fuel system, exhaust device, hydraulic system, transmission, axles, tires, frame, and chassis. The parts are illustrated with diagrams and specifications to aid in maintenance and repairs.
This document is an operation and maintenance manual for a wheel loader model 67Z7B/67TM7B powered by a Cummins QSB4.5 engine. It contains safety information, instructions for operating the engine and machine, maintenance procedures, troubleshooting steps, specifications, and attachments. The manual instructs operators to read it fully before use and save it on the machine.
Kawasaki 67 z7 67tm7 wheel loader service repair manual (65j5 8001 and up)fujsekksmem
This document provides guidelines and precautions for disassembling and reassembling a wheel loader. It discusses preparing the work area and tools, inspecting the machine beforehand, draining fluids properly, using identification tags, matching marks, and special tools as needed. Proper disassembly and reassembly are important to avoid damage and ensure correct functioning.
Kawasaki 67 z7 67tm7 wheel loader service repair manual (65j5 5001 and up)fujsekksmem
The document provides instructions and safety precautions for disassembling and assembling a wheel loader. It contains sections on general precautions, tightening specifications, painting, bleeding air, and preparing for inspection and maintenance. The general precautions section emphasizes cleaning parts and marking components for reassembly. It also provides guidelines for handling floating seals and nylon slings safely.
This document is an operation and maintenance manual for a wheel loader model 67Z7B/67TM7B powered by a Cummins QSB4.5 engine. It contains safety information, component identification, operating instructions, maintenance procedures, and specifications. The manual instructs operators on safe and proper use of the machine.
This document is a shop manual for wheel loaders models 62Z7, 67Z7, and 67TM7. It contains information on specifications, component layout, systems, component operation, operational performance testing, and troubleshooting. The wheel loaders are powered by an Isuzu 4HK1 engine. The manual includes diagrams, standards, procedures, and safety information to aid technicians in maintenance and repair.
This document contains summaries of two shop manuals for a wheel loader. The first manual covers the function and structure of the loader and includes sections on specifications, component layout, and descriptions of the controller, control systems, hydraulic system, and electrical system. The second manual covers operational performance testing and troubleshooting procedures for the loader. It includes sections on testing standards, engine testing, machine performance testing, component testing, and troubleshooting guides. Both manuals provide technical information for maintenance and repair of the loader.
Kawasaki 60 z7 wheel loader parts catalogue manual (60d1 8001 and up)fujsekksmem
This document is a parts catalog for a wheel loader model 60Z7 powered by a DEUTZ TCD3.6L4 engine. The catalog contains over 500 parts organized into the following sections: power train, engine, cab, chassis, hydraulic system, electric parts, and loader attachment. The parts listed include components of the transmission, cooling system, seats, controls, piping, cylinders, and attachments.
This document provides instructions for removing and installing exhaust and inlet valve guides on Caterpillar 325 excavators. The removal procedure involves using a valve guide driver tool to push the guides out of the cylinder head. For installation, new guides are lubricated and pressed into place using the same tool. Proper cleaning and lubrication are emphasized to prevent contaminants from causing premature wear.
This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 325-A FM L excavators. It describes removing bolts, studs, and gaskets and installing new gaskets before positioning the manifolds and tightening bolts with the specified torques. It also describes removing and installing inlet and exhaust valves by compressing springs, removing retainers and seals, and installing valves, springs, and retainers in reverse order.
Caterpillar cat 325 l track type excavator (prefix 8nl) service repair manual...fujsekksmem
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 3116 engine. It describes the required tools and parts, presents illustrations of the process, and provides step-by-step instructions including applying lubricant to seals, installing clips and pins, and setting adjustments. Special instructions are referenced for inspecting and modifying specific linkage components.
Caterpillar cat 325 l track type excavator (prefix 8jg) service repair manual...fujsekksmem
This document provides instructions for removing and installing an exhaust manifold on a 325-A excavator. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure describes applying anti-seize compound, installing new gaskets and bolts, and tightening the bolts in a specific sequence. Tools required are also listed.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A EXCAVATOR 9ZK
Configuration: 325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 8 22:55:25 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A EXCAVATOR 9ZK
Configuration: 325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 8 22:56:21 UTC+0800 2020
5/5
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A EXCAVATOR 9ZK
Configuration: 325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 8 22:57:16 UTC+0800 2020
4/4
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A EXCAVATOR 9ZK
Configuration: 325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 8 22:58:12 UTC+0800 2020
4/4
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A EXCAVATOR 9ZK
Configuration: 325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 8 22:59:08 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A EXCAVATOR 9ZK
Configuration: 325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 8 23:00:03 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A EXCAVATOR 9ZK
Configuration: 325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 8 23:00:59 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A EXCAVATOR 9ZK
Configuration: 325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 2 g01185803
Illustration 3 g00676791
1. Position the gasket and engine oil filter base (4) on the cylinder block.
2. Install the washers and bolts (2) that hold engine oil filter base (4) to the cylinder block.
Tighten the bolts according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Apply lubricant to new O-ring seal (5) . Install O-ring seal (5) in the fitting on the engine oil
filter base.
4. Connect tube assembly (1) to engine oil filter base (4) .
Note: Never install an oil filter with a wrench. Follow the instructions on the oil filter.
2/3
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. 5. Put a coat of fresh oil on the O-ring seal for the engine oil filter. Install engine oil filter (3)
on engine oil filter base (4) by hand.
6. After the O-ring seal contacts engine oil filter base (4) , turn engine oil filter (3) for 3/4 of a
turn.
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 8 23:01:55 UTC+0800 2020
3/3
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A EXCAVATOR 9ZK
Configuration: 325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943853
Engine Oil Filter Bypass Valve - Remove and Install
SMCS - 1308-010-BV
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/4
325, 325 L AND 325 LN EXCAVATORS 9ZK00001-UP (MACHINE) POWERED B...
2020/8/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...