This document provides instructions for disassembling and reassembling a wheel loader. It contains safety precautions and procedures for disassembly, cleaning, inspection, assembly, bleeding air from systems, and releasing pressures. The document is divided into sections covering general information, maintenance standards, specific components of the body, travel system, front attachment, and their groups. Precautions are given for tasks like using floating seals, nylon slings, cleaning, applying lubricants, and ensuring no tools are left inside after reassembly.
HITACHI 6HK1 ENGINE Service Repair Manualjksedmmdk
This is the Highly Detailed factory service repair manual for theHITACHI 6HK1 ENGINE , this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.HITACHI 6HK1 ENGINE Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Engine Manual (1/2)
Control System
Electronic Control Fuel Injection System
Engine Manual (2/2)
Disassemble and Assemble Engine
General Information
Engine Mechanical
Cooling System
Fuel System
Engine Electrical
Exhaust System and Turbocharger
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveHITACHI 6HK1 ENGINE Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
8
This is the Highly Detailed factory service repair manual for theHITACHI 4HK1 ENGINE, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.HITACHI 4HK1 ENGINE Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Engine Manual (1/2)
How to use this Manual
Precautions on Service Work
Procedure of Trouble Diagnosis
How to Inspect Injector
How to Use Breaker Box
Engine Control System
List of Function Checks
List of Diagnostic Trouble Codes
List of Trouble Symptom
Special Tool
Engine Manual (2/2)
General Information
Engine Mechanical
Cooling System
Fuel System
Engine Electrical
Exhaust System
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveHITACHI 4HK1 ENGINE Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
8
HITACHI 6HK1 ENGINE Service Repair Manualjksedmmdk
This is the Highly Detailed factory service repair manual for theHITACHI 6HK1 ENGINE , this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.HITACHI 6HK1 ENGINE Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Engine Manual (1/2)
Control System
Electronic Control Fuel Injection System
Engine Manual (2/2)
Disassemble and Assemble Engine
General Information
Engine Mechanical
Cooling System
Fuel System
Engine Electrical
Exhaust System and Turbocharger
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveHITACHI 6HK1 ENGINE Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
8
This is the Highly Detailed factory service repair manual for theHITACHI 4HK1 ENGINE, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.HITACHI 4HK1 ENGINE Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Engine Manual (1/2)
How to use this Manual
Precautions on Service Work
Procedure of Trouble Diagnosis
How to Inspect Injector
How to Use Breaker Box
Engine Control System
List of Function Checks
List of Diagnostic Trouble Codes
List of Trouble Symptom
Special Tool
Engine Manual (2/2)
General Information
Engine Mechanical
Cooling System
Fuel System
Engine Electrical
Exhaust System
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveHITACHI 4HK1 ENGINE Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
8
HITACHI ZAXIS 240 EXCAVATOR Service Repair Manualfusjejjsekkdmm
This is the Highly Detailed factory service repair manual for theHITACHI ZAXIS 240 EXCAVATOR, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.HITACHI ZAXIS 240 EXCAVATOR Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Manual Consists of the following separate Part No:
Technical Manual (Operational Principle) Vol. No. TO178-E
Technical Manual (Troubleshooting) Vol.No. TT178-E
Workshop Manual Vol.No. W178-E
Electrical Circuit Diagram
Workshop Manual Covers:
Safety
General Information
Upperstructure
Undercarriage
Front Attachment
Engine
Technical Manual (Operational Principle) Covers:
General
System
Component Operation
Technical Manual (Troubleshooting) Covers:
Operational Performance Test
Troubleshooting
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveHITACHI ZAXIS 240 EXCAVATOR Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
HITACHI ZAXIS 240 EXCAVATOR Service Repair Manualfusjejjsekkdmm
This is the Highly Detailed factory service repair manual for theHITACHI ZAXIS 240 EXCAVATOR, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.HITACHI ZAXIS 240 EXCAVATOR Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Manual Consists of the following separate Part No:
Technical Manual (Operational Principle) Vol. No. TO178-E
Technical Manual (Troubleshooting) Vol.No. TT178-E
Workshop Manual Vol.No. W178-E
Electrical Circuit Diagram
Workshop Manual Covers:
Safety
General Information
Upperstructure
Undercarriage
Front Attachment
Engine
Technical Manual (Operational Principle) Covers:
General
System
Component Operation
Technical Manual (Troubleshooting) Covers:
Operational Performance Test
Troubleshooting
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveHITACHI ZAXIS 240 EXCAVATOR Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
Similar to Kawasaki 70 tm7 wheel loader service repair manual (serial no. 70c6 5001 and up) (18)
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. SECTION AND GROUP
CONTENTS
WORKSHOP MANUAL
All information, illustrations and
specifications in this manual are based on
the latest product information available
at the time of publication. The right is
reserved to make changes at any time
without notice.
93208-00772 Vol.1/2
SECTION 1 GENERAL INFORMATION
Group 1 Precautions for Disassembling and Assembling
Group 2 Tightening
Group 3 Painting
Group 4 Bleeding Air
Group 5 Pressure Release Procedure
Group 6 Preparation
SECTION 2 MAINTENANCE STANDARD
Group 1 Body
Group 2 Travel System
Group 3 Front Attachment
Group 4 Front Attachment (Parallel Link)
SECTION 3 BODY
Group 1 Cab
Group 2 Counterweight
Group 3 Center Hinge
Group 4 Engine
Group 5 Radiator Assembly
Group 6 Hydraulic Oil Tank
Group 7 Fuel Tank
Group 8 Pump Device
Group 9 Control Valve
Group 10 Pilot Valve
Group 11 Brake Charge Valve
Group 12 Manifold Valve
Group 13 Solenoid Valve
Group 14 Priority Valve
Group 15 Cooling Fan System
Group 16 Ride Control Device
Group 17 Parallel Link (Special Parts)
3. SECTION AND GROUP
CONTENTS
WORKSHOP MANUAL
All information, illustrations and
specifications in this manual are based on
the latest product information available
at the time of publication. The right is
reserved to make changes at any time
without notice.
93208-00772 Vol.2/2
SECTION 4 TRAVEL SYSTEM
Group 1 Tire
Group 2 Drive Unit
Group 3 Axle
Group 4 Propeller Shaft
Group 5 Brake Valve
Group 6 Steering Device
Group 7 Secondary Steering Device
SECTION 5 FRONT ATTACHMENT
Group 1 Front Attachment
Group 2 Cylinder
Group 3 Front Attachment (Parallel Link)
Group 4 Cylinder (Parallel Link)
4. 70Z7/70TM7 D&R
Group 1 Precautions for Disassembling and
Assembling
Precautions for Disassembling and
Assembling.................................................................W1-1-1-1
Group 2 Tightening
Tightening Bolts and Nuts..........................................W1-2-1-1
Piping Joint ......................................................................W1-2-1-4
Group 3 Painting
Painting .............................................................................W1-3-1-1
Painting (Parallel Link)..................................................W1-3-2-1
Group 4 Bleeding Air
Bleeding Air from Hydraulic Oil Tank......................W1-4-1-1
Bleeding Air from Hydraulic System.......................W1-4-1-2
Bleeding Air from Fuel System..................................W1-4-1-3
Bleeding Air from Radiator.........................................W1-4-1-4
Bleeding Air from Brake (Axle)..................................W1-4-1-5
Group 5 Releasing Pressure
Front Attachment Hydraulic Circuit Pressure
Release Procedure....................................................W1-5-1-1
Ride Control Accumulator Pressure Release
Procedure....................................................................W1-5-1-2
Parking Brake Accumulator Pressure Release
Procedure....................................................................W1-5-1-3
Group 6 Preparation
Preparation before Inspection and
Maintenance ..............................................................W1-6-1-1
SECTION 1
GENERAL
CONTENTS
5. Group 1 Precautions for Disassembling and Assembling
SECTION 1 GENERAL
W1-1-1-1
Precautions for Disassembling and
Assembling
Precautions for Disassembling
Clean the Machine
Thoroughly wash the machine before bringing it
into the shop. Bringing a dirty machine into the shop
may cause machine components to be contaminated
during disassembling / assembling, resulting in
damage to machine components, as well as decreased
efficiency in service work.
Inspect the Machine
Be sure to thoroughly understand all disassembling
/ assembling procedures beforehand to help avoid
incorrect disassembling of components as well as
personal injury.
Check and record the items listed below to prevent
problems from occurring in the future.
The machine model, machine serial number, and
hour meter reading.
Reason for disassembly (symptoms, failed parts, and
causes).
Clogging of filters and oil, water or air leaks, if any.
Capacities and condition of lubricants.
Loose or damaged parts.
Prepare and Clean Tools and Disassembly Area
Prepare the necessary tools to be used and the area for
disassembling work.
Precautions for Disassembling and Assembling
Precautions for Disassembling
Cap the open ends in case the hoses and pipes
have been disconnected. In addition, attach an
identification tag onto the connectors, hoses, and
pipes for assembling.
Before disassembling, clean the exterior of the
components and place on a workbench.
Drain hydraulic oil and gear oil from the hydraulic
components and reduction gear.
Be sure to provide appropriate containers for
draining fluids.
Use matching marks for easier reassembling if
necessary.
Be sure to use the specified special tools when
instructed.
If a part or component cannot be removed after
removing its securing nuts and bolts, do not attempt
to remove it forcibly. Find the cause (s), then take the
appropriate measures to remove it.
Orderly arrange disassembled parts. Mark and tag
them if necessary.
Store common parts, such as bolts and nuts with
reference to where they are to be used and in a
manner that will prevent loss.
Inspect the contact or sliding surfaces of
disassembled parts for abnormal wear, sticking, or
other damage.
Measure and record the degree of wear and
clearances.
Precautions for Assembling
Be sure to clean all parts and inspect them for any
damage. If any damage is found, repair or replace
part.
Dirt or debris on the contact or sliding surfaces may
shorten the service life of the machine. Take care not
to contaminate any contact or sliding surfaces.
Apply appropriate lubricant oil onto parts in order to
prevent them from seizing.
Be sure to replace O-rings, backup rings, oil seals, and
floating seals with new ones once they have been
disassembled. Apply grease before installing
Be sure that liquid-gasket-applied surfaces are clean
and dry.
If an anti-corrosive agent has been used on a new
part, be sure to thoroughly clean the part to remove
the agent.
Fit the matching marks made when disassembling
and assemble them.
Be sure to use the designated tools to assemble
bearings, bushings, and oil seals.
Keep a record of the number of tools used for
disassembly / assembly. After assembling is
completed, count the number of tools so as to make
sure that no forgotten tools remain in the assembled
machine.
6. Group 1 Precautions for Disassembling and Assembling
SECTION 1 GENERAL
W1-1-1-2
Precautions for Using Floating Seal
1. In general, replace the floating seal with a new one
after disassembling.
If the floating seal is required to be reused, follow
these procedures:
Keep seal rings together as a matched set with seal
ring (1) surfaces together. Apply oil onto sliding
surface (e) of seal ring (1).
Check sliding surface (e) of seal ring (1) for scuffing,
scoring, corrosion, deformation, or uneven wear.
Check the step part of seal ring (1).
Check O-ring (2) for tears, breaks, deformation, or
hardening.
2. If incorrectly assembled, oil leakage or damage
will occur. Be sure to do the following to prevent
trouble.
Clean the floating seal and seal mounting bores with
cleaning solvent.
Use a wire brush to remove mud, rust, or dirt from
seal mounting bores. After cleaning, thoroughly dry
parts with compressed air.
Clean seal ring (1) and O-ring (2) mounting bores.
Check the bore surface for scuffing or scoring by
touching the surface with finger.
After installing the floating seal, check that O-ring (2)
is not twisted, and that it is installed correctly on seal
ring (1).
After installing the floating seal, check that O-ring
(2) and seal ring sliding surface (e) is parallel with
seal mating surface (f) by measuring the distances
(e) and (f) at point (A) and (B), as illustrated. If these
distances differ, correct O-ring (2) seating.
1
2
a
b
c
d
a - Correct
b - Incorrect
c - Twist of O-Ring
d - Bend of O-Ring
a - Correct
b - Incorrect
e - Sliding Surface
f - Seal Mating Surface
f
e
2
a A A
B B
b
A=B A≠B
W178-02-11-001
W178-02-11-002
W178-02-11-003
7. Group 1 Precautions for Disassembling and Assembling
SECTION 1 GENERAL
W1-1-1-3
Precautions for Using Nylon Sling
1. Follow the precautions below to use nylon slings
safely.
Attach protectors (soft material) on the corners of
the load so that the nylon sling does not directly
contact the corners. This will prevent the nylon
sling from being damaged and the lifted load from
slipping.
Lower the temperature of the lifted load to lower
than 100 °C (212 °F). If unavoidably lifting a load with
a temperature of 100 °C (212 °F) or more, reduce the
load weight.
Do not lift acid or alkali chemicals.
Take care not to allow the sling to become wet. The
load may slip.
When required to use more than one sling, use slings
with the same width and length to keep the lifted
load balanced.
When lifting a load using an eyehole, be sure to
eliminate any gaps between the sling and load.
(Refer to the right illustration.) Reduce the load
weight so that it is less than 80 % of the sling
breaking force.
Avoid using twisted, bound, connected, or hitched
slings.
Do not place any object on twisted or bent slings.
(Refer to the right illustration.)
When removing the slings from under the load, take
care not to damage the nylon slings. Avoid contact
with protrusions.
Avoid dragging slings on the ground, throwing
slings, or pushing slings with a metal object.
When using with other types of slings (wire rope) or
accessories (shackle), protect the joint so that the
nylon sling is not damaged.
Store the nylon slings indoors so that they won’t
deteriorate with heat, sun light, or chemicals.
a
b
c
a - Correct Eyehole Lifting
Method
b - Incorrect Eyehole Lifting
Method
c - Bent of Sling
W102-04-02-016
W105-04-01-008
W162-01-01-009
8. Group 1 Precautions for Disassembling and Assembling
SECTION 1 GENERAL
W1-1-1-4
dCAUTION: If a load is lifted with a damaged
nylon sling, serious personal injury may result.
Be sure to visually check the nylon sling for any
damage before using.
2. Before using a nylon sling, visually check the nylon
sling for any damage corresponding to examples
shown to the right. If any damage is found, cut and
discard the sling.
Even if no damage is found, do not use slings older
than 7 years.
Damaged Appearance a
a
a
e
f
b
b
c
c
g
d
a - Broken Sewing Thread a - Broken Sewing Thread e - Separation of Belt
b - Scuffing f - Scoring
b - Scuffing
c - Fuzz d - Broken Sewing Thread
c - Fuzz g - Broken Warp
a - Broken Sewing Thread
W162-01-01-002
W162-01-01-003
W162-01-01-004
W162-01-01-005
W162-01-01-006
W162-01-01-007
W162-01-01-008
9. Group 1 Precautions for Disassembling and Assembling
SECTION 1 GENERAL
W1-1-1-5
Maintenance Standard Terminology
“Standard”
1. Dimension for parts on a new machine.
2. Dimension of new components or assemblies
adjusted to specification. Allowable errors will be
indicated if necessary.
“Allowable Limit”
1. Normal machine performance cannot be
accomplished after exceeding this limit.
2. Repair or adjustment is difficult after exceeding this
limit.
3. Repair or adjustment is impossible after exceeding
this limit.
Therefore, in consideration of operation efficiency
and maintenance expense, proper maintenance
shall be carried out before reaching the“Allowable
Limit”.
10. Group 2 Tightening
SECTION 1 GENERAL
W1-2-1-1
Tightening Bolts and Nuts
dCAUTION: Use tools appropriate for the work
to be done. Makeshift tools and procedures
can create safety hazards. For loosening and
tightening nuts and bolts, use correct size tools.
Otherwise, tightening tools may slip, potentially
causing personal injure.
IMPORTANT:
Apply lubricant to the bolts and nuts in order
to reduce friction coefficient of them. (For
example, spindle oil with white zinc B dissolved
in it)
Clean the bolt and nut threads and remove dirt
or corrosion before installing.
Bolt Types
Tighten the nuts or bolts correctly to the torque
specifications.
As the different types and grades of bolt are used,
use and tighten the correct bolts correctly when
assembling the machine or components.
Specified Tightening Torque Chart
2013/09
Bolt
Dia.
Hexagon Head Bolt Socket Bolt
Wrench
Size
mm
Socket Bolt Wrench
Size
mm
N·m (lbf·ft) N·m (lbf·ft) N·m (lbf·ft) N·m (lbf·ft)
M6 3 to 4 (2.2 to 3) 10 5
M8 30 (22) 20 (15) 10 (7.4) 13 20 (15) 6
M10 65 (48) 50 (37) 20 (15) 17 50 (37) 8
M12 110 (81) 90 (66) 35 (26) 19 90 (66) 10
M14 180 (133) 140 (103) 55 (41) 22 140 (103) 12
M16 270 (200) 210 (155) 80 (59) 24 210 (155) 14
M18 400 (300) 300 (220) 120 (89) 27 300 (220) 14
M20 550 (410) 400 (300) 170 (125) 30 400 (300) 17
M22 750 (550) 550 (410) 220 (162) 32
M24 950 (700) 700 (520) 280 (205) 36
M27 1400 (1030) 1050 (770) 400 (300) 41
M30 1950 (1440) 1450 (1070) 550 (410) 46
M33 2600 (1920) 1950 (1440) 750 (550) 50
M36 3200 (2360) 2450 (1810) 950 (700) 55
WDAA-01-02-001
WDAA-01-02-002 WDAA-01-02-003 WDAA-01-02-004
11. Group 2 Tightening
SECTION 1 GENERAL
W1-2-1-2
IMPORTANT: The following items are applied to both
fine and coarse pitch threads.
Apply lubricant to the bolts and nuts in order
to reduce friction coefficient of them. (For
example, spindle oil with white zinc B dissolved
in it)
Torque tolerance is ±10 %.
Use the bolts of correct length. The bolts that
are too long cannot be tightened as the bolt tip
comes into contact with the bottom of bolt hole.
Also the bolts that are too short cannot develop
sufficient tightening force.
The torque given in the chart on the previous
page are for general use only, however,
a different torque is given for a specific
application. Use the specified torque.
Clean the nut and bolt threads and remove dirt
or corrosion before installing.
Tightening Order
When tightening two or more bolts, tighten them
alternately, as shown, to ensure even tightening.
a
1.4
1 12
13
9
8
4
5
1
2
6
3
7
10
14
11
3
5
2
4
6
2.3
b c
a - Equally tighten upper and
lower alternately
b - Tighten diagonally c - Tighten from center
diagonally
W105-01-01-003
12. Group 2 Tightening
SECTION 1 GENERAL
W1-2-1-3
Precautions for Split Flange
IMPORTANT:
Clean the sealing surfaces. Check if there are
any scratches and roughness on the surface of
the seal that cause oil leaks and damage to the
O-ring.
Use only specified O-rings. Inspect O-rings for
any damage. Do not file the O-ring surfaces.
When installing O-ring into a groove, use grease
in order to hold O-ring in place.
While tightening the bolt by hand, check that
flange is installed to the port correctly. Do not
pinch the O-ring.
Tighten the bolts up and down, left and right
alternately, in order to ensure even tightening
to the specified torque.
Do not use air wrenches. Using an impact
wrench often causes tightening of one bolt fully
before tighten the others, resulting in damage
to O-rings or uneven tightening of bolts.
Nut and Bolt Locking
Lock Plate
IMPORTANT: Do not reuse the lock plates. Do not try
to bend the same point twice.
Split Pin
IMPORTANT: Do not turn in the loosening direction
in order to align the grooves and holes on the nut.
Always turn in the tightening direction. Do not
reuse the split pins.
Wire
IMPORTANT: Attach wire to bolts in the bolt-
tightening direction. Do not reuse the wire.
Incorrect
Correct
Correct
Correct
Correct
Correct
Correct
a
a
b
d
c
Incorrect
Incorrect
Incorrect
Incorrect
a- Bend along edge sharply b- Do not bend it round
c- Tighten d- Loosen
WDAA-01-02-005
WDAA-01-02-006
W105-01-01-008
WDAA-01-02-007
WDAA-01-02-008
13. Group 2 Tightening
SECTION 1 GENERAL
W1-2-1-4
Piping Joint
IMPORTANT:
The torque given in table below are for general
use only, however, a different torque is given for
a specific application. Use the specified torque.
Apply lubricant, such as the Grease Spray to
the bolts and nuts in order to reduce friction
coefficient of them.
Torque tolerance is ±10 %.
Slightly apply lubricant onto the threads first by
using the Grease Spray.
14. Group 2 Tightening
SECTION 1 GENERAL
W1-2-1-5
Union Joint
Metal sealing surfaces (4) and (5) of adapter (1) and
hose (2) fit together to seal pressure oil. Union joints
are used to join small-diameter lines.
IMPORTANT:
Do not over-tighten union nut (3). Excessive
force will be applied to metal sealing surfaces (4)
and (5), possibly cracking the adapter. Tighten
union nut (3) to the specifications.
Scratches or other damage to sealing surfaces
(4) or (5) will cause oil leakage at the joint. Take
care not to damage them when connecting /
disconnecting.
2013/09
Description Wrench Size
mm
Tightening Torque
Union Nut N·m (lbf·ft)
30 ° male 17 25 (18.5)
19 30 (22)
22 40 (29.5)
27 80 (59)
32 140 (103)
36 180 (133)
41 210 (155)
50 350 (260)
55 380 (280)
60 380 (280)
37 ° female 17 25 (18.5)
19 30 (22)
22 40 (29.5)
27 80 (59)
32 140 (103)
36 180 (133)
41 210 (155)
50 350 (260)
fNOTE: Tightening torque of 37 ° male coupling without
union is similar to tightening torque of 37° female.
a - Joint Body
b - Male Union Joint c - Female Union Joint
1
30 °
37 °
b c
4 3 2
a
5
WDAA-01-02-009
WDAA-01-02-010
15. Group 2 Tightening
SECTION 1 GENERAL
W1-2-1-6
Pipe Joint
Pipe connection (metal joint)
(Union Nut Wrench Size: 17, 19, 22, 27 mm
Metal (3) of adapter (1) and pipe (2) seals pressure oil.
Precautions for use
Do not damage sealing surfaces (4) and (5) when
disassembling and assembling.
Tightening Torque
Use the specified tightening torque in the table below.
2013/09
Wrench Size (mm) 17 19 22 27
Tightening
Torque
N·m 25 30 40 80
(lbf·ft) (18.5) (22) (29.5) (59)
O-ring Seal Joint
O-ring (6) is installed against the end surface of adapter
(7) and seals pressure oil.
IMPORTANT:
Replace O-ring (6) with a new one when
reinstalling.
Before tightening union nut (9), confirm that
O-ring (6) is seated correctly in O-ring groove
(8). Tightening union nut (9) with O-ring (6)
displaced will damage O-ring (6), resulting in oil
leakage.
Do not damage O-ring groove (8) of adapter (7)
or sealing surface (10) on the hose side. Damage
to O-ring (6) may cause oil leakage.
If union nut (9) is found to be loose, causing
oil leakage, do not tighten it to stop the leak.
Instead, replace O-ring (6) with a new one, then
tighten union nut (9) after confirming that
O-ring (6) is securely seated in O-ring groove (8).
1 4 5 3 2
7 6 9
8 10 a
a - Joint Body
2013/09
Wrench Size
mm (in)
Tightening Torque
Union Nut N·m (lbf·ft)
19 (0.75) 30 (22)
22 (0.87) 70 (52)
27 (1.06) 95 (70)
32 (1.26) 140 (103)
36 (1.42) 180 (133)
41 (1.61) 210 (155)
50 (1.97) 350 (260)
M1M7-07-005
WDAA-01-02-011
16. Group 2 Tightening
SECTION 1 GENERAL
W1-2-1-7
Quick Coupling
1. Coupling procedure
Push socket ring (1) into plug (3) by rotating it fully
counterclockwise and then pulling it toward you.
Release socket ring (1). Check that socket ring (1)
is returned by the spring force and the coupling is
locked completely by ball (2). At this time, check if
socket ring (1) is returned to the original position (to
the rightmost direction).
2. Separating procedure
Remove the hose by rotating socket ring (1) fully
counterclockwise and then pulling it. Because no
check function is attached inside, be careful that oil
flows out.
Cap the removed hoses using special plug.
dCAUTION:
When disconnecting, do not damage joint
surface.
When disconnecting, clean the joint part and
thoroughly wipe off the cleaning solution to
prevent any foreign material from entering.
Complete the joint disconnecting / connecting
procedure. Check enough if oil leaks especially
after installation.
After installation, check if socket ring (1)
is returned to the original position (to the
rightmost direction).
1
3
2
M1M7-07-006
17. Group 2 Tightening
SECTION 1 GENERAL
W1-2-1-8
Screw-In Connection
Depending on types of screw and sealing, different
types of screw-in connection are used.
IMPORTANT: Check that the thread pitch and thread
type (tapered or straight) are the correct type
before using any screw-in connection. (In general,
the screw-in connection of male tapered thread (a)
is used except for measurement purpose.)
Seal Tape Application
Seal tape is used in order to seal clearances between
male (d) and female (c) threads so that any leaks
between threads may be prevented. Therefore, apply
just enough seal tape to fill up thread clearances (e). Do
not overlap.
Application Procedure
Check that the thread surface is clean and, free of dirt
or damage. Apply the seal tape around threads in order
to leave one to two pitch threads uncovered. Wrap the
seal tape in the same direction as the threads.
Low-Pressure-Hose Clamp Tightening
Low-pressure-hose clamp tightening torque differs
depending on the type of clamp.
T-Bolt Type Band Clamp (g):
4.5 N·m (3.3 lbf·ft)
Worm Gear Type Band Clamp (h):
6 to 7 N·m (4.4 to 5.2 lbf·ft)
R
a
c
f
d
b
G
30 °
a - Male Tapered Thread b - Male Straight Thread
c - Internal Thread
d - External Thread
e - Clearance
f - Leave one to two pitch
threads uncovered
2013/09
Wrench Size mm Tightening Torque
Joint Body Cast iron Structural rolled
steel
19 15 (11) 35 (26)
22 30 (22) 50 (37)
27 50 (37) 95 (70)
36 70 (52) 160 (118)
41 110 (81) 200 (148)
50 160 (118) 330 (245)
60 200 (148)
fNOTE: Unit: N·m (lbf·ft)
e
g - T-Bolt Type Band Clamp h - Worm Gear Type Band Clamp
g h
W105-01-01-018
W105-01-01-019
M114-07-041
M114-07-043
WDAA-01-02-012
18. Group 2 Tightening
SECTION 1 GENERAL
W1-2-1-9
Connecting Hose
dCAUTION: When replacing the hoses, use only
genuine KCM/Hitachi service parts. Using hoses
other than genuine KCM/Hitachi hoses may cause
oil leaks, hose rupture or separation of fitting,
possibly resulting in a fire on the machine. Do
not install hoses kinked. Application of high oil
pressure, vibration, or an impact to a kinked hose
may result in oil leaks, hose rupture or separation
of fitting. Utilize the print marks on hoses when
installing in order to prevent hose from being
kinked. Take necessary measures to protect hoses
from rubbing against each other. If the hoses rub
against each other, wear to the hoses may result
and lead to hose rupture. Take care so that the
hoses do not come into contact with the moving
parts or sharp objects.
a
a - Rubbing Against Each Other
a - Rubbing Against Each Other b - Clamp
a - Rubbing Against Each Other b - Clamp
b b
a
a
b
Incorrect
Incorrect
Incorrect
Incorrect
Correct
Correct
Correct
Correct
W105-01-01-011
W105-01-01-012
W105-01-01-013
W105-01-01-014
19. Group 3 Painting
SECTION 1 GENERAL
W1-3-1-1
Painting
Surfaces to Be Painted Painting Color
1 Pipe High Grade Black
2 Pipe (Lift Cylinder) High Grade Black
3 Pipe High Grade Black
4 Bracket (Control Valve) High Grade Black
5 Cab (Outside) High Grade Black
6 Plate Shining Silver
7 Handrail High Grade Black
8 Rear Console (Inner) High Grade Black
9 Seat Bracket High Grade Black
10 Cockpit Skirt High Grade Black
11 Cockpit High Grade Black
12 Side Console (Inner) High Grade Black
13 Cab (Inner) High Grade Black
Paint the painted surface except the above list in YR-01(TAXI Yellow).
4 1
3
2
5
13
12
11
6
8
7
9
10
WNEC-01-03-002
WNDB-01-03-001
20. Group 3 Painting
SECTION 1 GENERAL
W1-3-1-2
Surfaces to Be Painted Painting Color
1 Light Bracket High Grade Black
2 Hydraulic Oil Tank High Grade Black
3 Exhaust Pipe Black Heat-Resistant Painting
4 Air Duct High Grade Black
5 Grill High Grade Black
6 Bracket (Work Light) High Grade Black
7 Rear Cover (Side) High Grade Black
8 Handrail High Grade Black
9 Side Cover (Lower) High Grade Black
10 Lower Cover High Grade Black
11 Articulate Lock Bar Red
12 Pipe High Grade Black
13 Pipe Guard High Grade Black
Paint the painted surface except the above list in YR-01(TAXI Yellow).
1 2 3 4
9 8 7
6
5
10
11
12
13
WNDB-01-03-002
21. Group 3 Painting
SECTION 1 GENERAL
W1-3-1-3
Surfaces to Be Painted Painting Color
1 Handrail (Front) High Grade Black
2 Tool Box High Grade Black
3 Rear Fender High Grade Black
4 Handrail (Rear) High Grade Black
5 Fender Cover (Rear) Do not paint it.
6 Full Fender Do not paint it.
7 Bracket (Full Fender) High Grade Black
8 Bracket (Mud Guard) High Grade Black
9 Deck Plate High Grade Black
10 Step High Grade Black
11 Fender Cover (Front) Do not paint it.
Paint the painted surface except the above list in YR-01(TAXI Yellow).
3
2
1 4 5 6
7
8
11 10 9 WNDB-01-03-003
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Group 3 Painting
SECTION 1 GENERAL
W1-3-1-4
Surfaces to Be Painted Painting Color
1 Plate High Grade Black
2 Support (Real Axle) High Grade Black
3 Rear Axle Refer to W1-3-1-5
4 Front Axle Refer to W1-3-1-6
5 Guard High Grade Black
Paint the painted surface except the above list in YR-01(TAXI Yellow).
2
1
5 4
3
WNEC-01-03-005
24. Group 3 Painting
SECTION 1 GENERAL
W1-3-1-5
Surfaces to Be Painted Painting Color
1 Rear Axle High Grade Black
2 Rim (Wheel) Mounting Part Do not paint it.
3 End of Axle and Rim (Wheel) YR-01(TAXI Yellow)
4 Boss Part Do not paint it.
5 Boss Part Do not paint it.
6 Guard Mounting Part (Thread Part ) Do not paint it.
7 Flange Part Do not paint it.
8 Name Plate Do not paint it.
9 End of Boss Part Do not paint it.
10 Guard Mounting Part (Thread Part ) Do not paint it.
WNEC-01-03-007
WNEC-01-03-008
WNEC-01-03-009
WNEC-01-03-010
View A View C
View B
8 10
9
B
4
5
6
C
A
7
1 2 3 2
25. Group 3 Painting
SECTION 1 GENERAL
W1-3-1-6
Surfaces to Be Painted Painting Color
1 Rim (Wheel) Mounting Part Do not paint it.
2 End of Axle and Rim (Wheel) YR-01(TAXI Yellow)
3 Front Axle High Grade Black
4 Axle Mounting Part Do not paint it.
5 Flange Part Do not paint it.
6 Guard Mounting Part (Thread Part ) Do not paint it.
7 Name Plate Do not paint it.
8 Nut Surface Do not paint it.
9 Guard Mounting Part (Thread Part ) Do not paint it.
10 Connector Do not paint it.
View A
WNEC-01-03-011
WNEC-01-03-012
8 9 10
7 6 5 A
1 2 1 3 4