8. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
51481238 06/06/2018
5
9. INTRODUCTION
Safety rules - General information
Cleaning
Clean the metal parts with cleaning solution that meets the standard and steam cleaning. (except for bearings)
After cleaning, dry well, and inject oil in all parts.
Also inject oil into the bearings after drying.
Inspection
When disassembling parts, check all the parts.
If there are any worn or damaged parts, replace them.
Inspect carefully to prevent initial breakdowns.
Bearing
Replace any loose bearings.
Air dry bearings before installing them.
Needle bearing
When inserting needle bearings, be very careful not to damage them.
Apply grease to the section where the needle bearing will be inserted.
Gear
Check that there is no wear and no damage.
Oil seal, O-ring, gasket
Always install new oil seals, O-rings, and gaskets.
Apply grease to sections where oil seals and O-rings will be inserted.
Shaft
Check that there is no wear and no damage.
Check the bearings and check for damaged oil seals on the shaft.
Service parts
Install CASE CONSTRUCTION genuine service parts.
When placing an order, check the parts catalog. It contains the CASE CONSTRUCTION genuine part numbers.
Any breakdowns arising from the installation of non-genuine parts are not covered by the warranty.
Lubricants (fuel, hydraulic oil)
Use the oil from the specified company or specified in the operator's manual or service Manual.
Any breakdowns arising from any fuel or hydraulic oil other than those specified are not covered by the warranty.
51481238 06/06/2018
6
10. SERVICE MANUAL
Engine
CX350D Crawler excavators LC version (TIER4 FINAL) - EU Market , CX350D
Crawler excavators LC version (TIER4 FINAL) - MEA Market, CX350D Crawler
excavators NLC version (TIER4 FINAL) - EU Market , CX370D Crawler
excavators LC triple articulation version (Tier 4 Final) - EU Market, CX370D
Crawler excavators LC version (TIER4 FINAL) - EU Market, CX370D Crawler
excavators LC version (TIER4 FINAL) - MEA Market, CX370D Crawler
excavators NLC triple articulation version (Tier 4 Final) - EU Market, CX370D
Crawler excavators NLC version (TIER4 FINAL) - EU Market
51481238 06/06/2018
10
11. Engine - Engine and crankcase
Engine - General specification
Engine main specifications
Item Engine model 6HK1
Type
Diesel/4-cycle/water-cooled, inline 6 cylinder
OHC
Shape of combustion chamber Direct injection type
Cylinder liner type Dry type
Cylinder bore x stroke 115 mm (4.53 in) x 125 mm (4.92 in)
Displacement 7.79 L (475.37 in³)
Compression ratio 16.3
Compression pressure 3 MPa (441 psi) 200 RPM
Idling speed 800 RPM
Intake 0.4 mm (0.016 in) While cool
Valve clearance
Exhaust 0.4 mm (0.016 in) While cool
Ignition method Compression ignition
Injection order 1, 5, 3, 6, 2, 4
Lubrication system
Lubrication type Compression type
Oil pump type Gear type
Lubrication oil amount 36 – 46 L (9.5 – 12.2 US gal)
Oil filter type Full-flow filter (Cartridge type)
Oil cooling type Built-in type, water cooling
Cooling system
Cooling type Water cooling
Radiator type Corrugated fin (Pressure type)
Water pump type Centrifugal type, belt type
Thermostat type 2-wax type unit
76 °C (170 °F) With jiggle valve
Type 1
82 °C (180 °F) Without jiggle valve
85 °C (185 °F) With jiggle valve
Thermostat valve open valve
temperature
Type 2
82 °C (180 °F) Without jiggle valve
Coolant capacity 16.0 L (4.2 US gal)
Fuel system
Injection pump type Electronic control common rail (fuel rail) type
Governor type Electronic type
Timer type Electronic type
Injection nozzle type
Multi-hole type 7 holes, inner diameter Ø
0.14 mm (0.0055 in)
Charging system
Generator type AC type
Output 24 – 90 V 50 A
Regulator type IC
Starter system
Starter type Reduction type
Output 24 V 5.0 kW
Preheat system type Glow plug
Glow plug standard voltage/current 23 V 3.5 A
51481238 06/06/2018
10.1 [10.001] / 3
12. Engine - Engine and crankcase
Cooling system main specifications
Item Specifications
Water pump Centrifugal impeller method
Type 1 0.80
Pulley ratio
Type 2 0.85
Thermostat Wax pellet type
90 °C (194 °F) With jiggle valve
Type 1
95 °C (203 °F) Without jiggle valve
100 °C (212 °F) With jiggle valve
Full open temperature
Type 2
95 °C (203 °F) Without jiggle valve
Electrical system main specifications
Generator
Item Specification
Manufacturer name Mitsubishi Electric Corporation
Isuzu parts number 1-81200-633-0 1-81200-603-2
Manufacturer type A009TU3782 A004TU6285
Nominal voltage 24 V
Output current 90 A 50 A
Rated rotation count 5000 RPM
Output current/voltage 114 A/ 27 V/ 5000 RPM 50 A/ 27 V/ 5000 RPM
No-load voltage 24 V/ 900 RPM
Rotational direction Clockwise direction
Polarity (-)
Pulley diameter (P.C.D) 90.0 mm (3.54 in) 80.0 mm (3.15 in)
Starter
Item Specification
Manufacturer Mitsubishi Electric Corporation
Isuzu parts number 181100-4140
Manufacturer code number M008T60971
Output 24 V/ 5.0 kW
Rating 30 s
York outer diameter 85.0 mm (3.35 in)
Rotational direction Right
Protection type Dust proof, drip proof
Low speed mechanism Inner contact gear
Weight 7.2 kg (15.9 lb)
Module 3
Pressure angle 14.5
Number of teeth 11Pinion
Gear ratio{ring
gear/pinion gear}
12.8 {129/11}
Voltage 23 V
Current 85 A or lessNo load
Rotational speed 3300 RPM or more
Voltage 9 V
Current 1,400 or lessRestraint
Torque 88 N·m (65 lb ft) or more
Pinion/engaged voltage 16.0 V or less
Glow plug
Item Type
Preheat device model Glow plug
Glow plug rated voltage/current 23 V/ 3.5 A
51481238 06/06/2018
10.1 [10.001] / 4
13. Engine - Engine and crankcase
Engine - Identification
Engine number
SMIL14CEX3961GB 1
1. Engine number stamping
51481238 06/06/2018
10.1 [10.001] / 7
14. Engine - Engine and crankcase
Engine - Static description
The control provided by the control unit applies to the range from injection to air intake and exhaust, including fuel
injection quantity, injection timing, air intake restriction, EGR, and idling speed.
Cylinder block
The cylinder block is made of cast iron, and it has an equal center distance for each bore and a high rigidity, and the
center of the crankshaft matches the center of the block. Tighten the bearing cap using the plastic region rotational
angle tightening method with the ladder frame structure.
Cylinder liner
A cylinder liner that matches with the cylinder block bore inner diameter is selected, and the identification number is
stamped on the left side of the cylinder.
Piston
The piston is a strut cast autothermatic piston made of aluminum alloy, and the combustion chamber is the round
re-entrant type.
Cylinder head
The cylinder head is made of cast iron and has four valves per cylinder. The angle tightening method has been
adopted for the cylinder head bolt to further improve its reliability and durability.
Crankshaft
The crankshaft uses tufftrided steel, and each of the journal diameter grades are marked on the No. 1 balance weight.
EGR system
The EGR system is controlled by the engine control module (ECM) according to various data, including the water
temperature, engine speed, and engine load, to recirculate the exhaust gas for purification. The primary components
are the EGR valve, EGR cooler, and various sensors.
Connecting rod cap bolt
The angle tightening method has been adopted for the connecting rod cap bolt to further improve its reliability and
durability.
Common rail (fuel rail) type electronic control injection system
The common rail (fuel rail) type electronic control injection system consists of the fuel supply pump that sets the target
pressure of the high pressure fuel to supply the fuel, the common rail (fuel rail) that measures the high-pressure fuel,
and the fuel injector that injects the fuel in the form of a fine mist. Each of these is controlled by the ECM based on
various signals that control the injection timing and injection quantity in accordance with driving conditions.
Fuel injector
The fuel injector has adopted the 7- hole nozzle, and adjusts the fuel injection quantity and injection timing by opening
or closing the electromagnetic valve on the injector head portion.
The ECM corrects variations in the fuel injection quantity between fuel injectors in accordance with the ID code data
in the memory. When adjusting the fuel injector, the ID code data must be recorded in the ECM.
Fuel filter with sedimenter
The fuel filter with sedimenter removes water by using the difference in the specific gravity of diesel oil and water, and
notifies the operator through the indicator when it becomes full of water.
51481238 06/06/2018
10.1 [10.001] / 10
15. Engine - Engine and crankcase
Preheat system
The preheat system consists of the ECM, glow relay, glow plug, and glow indicator light. The preheat system is
activated when the engine coolant temperature is low so as to help the engine start.
Lubricating system
An oil filter with a full-flow bypass is used, and the pistons are cooled down using the water-cooled oil cooler and the
oil jet.
51481238 06/06/2018
10.1 [10.001] / 11
16. Engine - Engine and crankcase
Engine - Prepare
WARNING
Escaping fluid!
Hydraulic fluid or diesel fuel leaking under pressure can penetrate the skin and cause infection or
other injury. To prevent personal injury: Relieve all pressure before disconnecting fluid lines or per-
forming work on the hydraulic system. Before applying pressure, make sure all connections are tight
and all components are in good condition. Never use your hand to check for suspected leaks under
pressure. Use a piece of cardboard or wood for this purpose. If injured by leaking fluid, see your
doctor immediately.
Failure to comply could result in death or serious injury.
W0178A
WARNING
Avoid injury!
Shut off the engine, remove the key, and make sure all motion is stopped before servicing the machine.
Failure to comply could result in death or serious injury.
W1128A
WARNING
Crushing hazard!
The lifting systems must be operated by qualified personnel who are aware of the correct procedures
to follow. Make sure all lifting equipment is in good condition, and all hooks are equipped with safety
latches.
Failure to comply could result in death or serious injury.
W0256A
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
WARNING
Explosion hazard!
Batteries emit explosive gases. Always ventilate when using in an enclosed area or when charging.
Keep the battery away from sparks, open flames, and other ignition sources.
Failure to comply could result in death or serious injury.
W0369A
NOTICE: Keep away from flames.
NOTICE: The air conditioner circuit is filled with high pressure gas, gas may spray out dangerously when loosening
lines.
51481238 06/06/2018
10.1 [10.001] / 12
17. Engine - Engine and crankcase
Items to prepare:
• Wrenches [ 7 mm, 8 mm, 10 mm, 13 mm, 17 mm,
19 mm, 36 mm ]
• Box wrench [ 30 mm]
• Shackle (with the required lifting capacity) x 2
• Wire rope (with the required breaking load)
• Lifting equipment (with the required lifting capacity)
• Marking pen
• Cap
• Plug
• Waste oil can
• Rag
• Cleaning fluid
• Wood plank, etc.
51481238 06/06/2018
10.1 [10.001] / 13
18. Engine - Engine and crankcase
Engine - Remove
1. Remove the cable connected to minus side of the bat-
tery or turn OFF the battery disconnect switch.
NOTICE: While the indicator (LED) of the battery discon-
nect switch is lit, do not turn OFF the battery disconnect
switch or disconnect its negative cable from the battery.
(After key OFF, lit for a maximum duration of 3 min)
• Secure the terminal and harness in order to prevent
them from touching the frame or other parts when
they have been removed.
• Or protect them with a rubber cap or other cap to
prevent sparks.
2. Remove the 5 bolts (1) with a wrench [ 19 mm] to re-
move the under cover (2).
Bolt tightening torque: 63.7 – 73.5 N·m (47.0 –
54.2 lb ft)
SMIL14CEX0769AB 1
3. Drain engine oil.
4. Drain coolant of the radiator. (Refer to Radiator - Re-
move (10.400) for detail.)
5. Remove the engine hood. (Refer to Hood - Remove
(90.100) for detail.)
6. Remove the hydraulic pump. (Refer to Pump - Re-
move (35.106) for detail.)
7. Remove the radiator hose and fan shroud. (Refer to
Radiator - Remove (10.400) for detail.)
8. Remove lines from the compressor. (Refer to Air-con-
ditioning compressor - Remove (50.200) for detail.)
9. Remove wirings from the starter. (Refer to Engine
starter - Remove (55.201) for detail.)
10. Remove wirings from the alternator. (Refer to Alter-
nator - Remove (55.301) for detail.)
51481238 06/06/2018
10.1 [10.001] / 14
19. Engine - Engine and crankcase
11. Remove the 2 bolts (1) with a wrench [ 13 mm] to
remove the box cover (2).
SMIL14CEX0770AB 2
12. Disconnect the 5 connections (1) of the engine har-
ness and frame main wire harness in the box.
• Wrap the disconnected connectors with a vinyl after
bundle them so as to prevent invasion of water, dust
and dirt.
SMIL14CEX0771AB 3
13. Loosen the hose band (1) with a wrench [ 7 mm] to
remove the air cleaner (2).
Loosen the hose band (3) with a wrench [ 7 mm] to
remove the 2 intercooler hoses (4).
Remove the 4 nuts (5) to remove the exhaust pipe (6).
SMIL14CEX0772AB 4
51481238 06/06/2018
10.1 [10.001] / 15
20. Engine - Engine and crankcase
14. Remove the hose band (1) to remove the 2 urea
coolant hoses (2).
Remove the hose band (3) to remove the 2 heater
hoses (4).
• Attach caps and plugs at the engine and the hoses
so as to prevent invasion of water, dust and dirt.
SMIL14CEX0773BB 5
15. Remove the hose band (1) to remove the 2 fuel hoses
(2).
• Attach caps and plugs at the engine and the hoses
so as to prevent invasion of water, dust and dirt.
SMIL14CEX0774AB 6
16. Prepare a waste oil can and then remove the 2 engine
oil remote hoses ( (1) with a wrench [ 36 mm].
• Apply marking at each location of the engine and
the hoses so as to match connections at assem-
bling.
• Attach caps and plugs at each location of the en-
gine and the hoses so as to prevent invasion of wa-
ter, dust and dirt.
• Wash each location of the engine and the hoses by
blowing parts cleaner so as to prevent adhering dirt
at connections and not to damage them.
SMIL14CEX0775AB 7
51481238 06/06/2018
10.1 [10.001] / 16
21. Engine - Engine and crankcase
17. Attach the 2 shackles (1) and then secure the engine
main unit with a wire rope (2) and a lifting equipment.
SMIL14CEX0776AB 8
18. Remove the 4 bolts (1) with a box wrench [ 30 mm].
Bolt tightening torque: 289 – 337 N·m (213.16 –
248.56 lb ft)
SMIL14CEX0777BB 9
51481238 06/06/2018
10.1 [10.001] / 17
22. Engine - Engine and crankcase
19. Lift the engine main unit with a wire rope (1) and a
lifting equipment.
Make sure that you have a safe site, and then settle the
engine on a wood plank or other block.
SMIL14CEX0778BB 10
51481238 06/06/2018
10.1 [10.001] / 18
23. Engine - Engine and crankcase
Engine - Install
1. Install the engine in the reversed order of the procedure
for removal.
Each bolt has to be tightened in the specified torque.
Refer to the Torque - Bolt and nut () for tightening
torque for bolts without instruction.
After installation, fill coolant, fill engine oil, bleed air
from the fuel line, wash and fill air conditioner gas.
Follow respective procedures and descriptions for de-
tail.
2. Make sure that there is no water leak or oil leak by
running the engine in idle speed with no load.
51481238 06/06/2018
10.1 [10.001] / 19
24. Engine - Engine and crankcase
Engine - Check - Engine oil
WARNING
Burn hazard!
Do not handle any service fluid (engine coolant, engine oil, hydraulic oil, etc.) at temperatures that
exceed 49 °C (120 °F). Allow fluids to cool before proceeding.
Failure to comply could result in death or serious injury.
W0330B
NOTICE: The engine should be in a horizontal position.
NOTICE: Wait at least 5 min before starting the engine and after stopping the engine.
Engine oil inspection
1. Remove the oil level gauge from the oil level gauge
guide tube.
NOTE: Wipe off the engine oil remaining on the oil level
gauge.
2. Install the oil level gauge to the oil level gauge guide
tube.
3. Remove the oil level gauge from the oil level gauge
guide tube.
4. Inspect the engine oil.
NOTE: Check the engine oil remaining on the oil level
gauge to inspect the engine oil level.
1. Upper limit
2. Lower limit
NOTE: If the oil level is under the lower limit, add engine
oil. Replace the engine oil if engine oil is dirty.
SMIL14CEX3221AB 1
51481238 06/06/2018
10.1 [10.001] / 20
25. Engine - Engine and crankcase
Engine - Test - Engine oil
Sampling of engine oil
1. Open the side door (1).
At this time, make sure to apply the lock (2).
SMIL14CEX1174AB 1
2. Place a sampling container under the sampling port (1).
3. Open the valve (2) to drain a proper amount of oil.
4. Close the valve (2) to check that there is no leakage.
5. If necessary, add the same amount of oil as the drained
oil.
SMIL14CEX1175AB 2
51481238 06/06/2018
10.1 [10.001] / 21
26. Engine - Engine and crankcase
Engine - Compression test
NOTE: Warm up the engine.
1. Remove the glow plug from the cylinder head assem-
bly.
NOTE: Remove all the glow plugs.
2. Remove the injector harness connectors from the lower
cover.
SMIL14CEX3444AA 1
3. Install the special tool on the cylinder head assembly.
Special tool: Compression gauge adapter (Refer
to Cylinder head - Special tools (10.101))
SMIL14CEX3445AA 2
Special tool: Compression gauge (adapter) (Refer
to Cylinder head - Special tools (10.101))
SMIL14CEX3446AA 3
51481238 06/06/2018
10.1 [10.001] / 22
27. Engine - Engine and crankcase
4. Insert the compression gauge adapter (2) into the glow
plug installation hole to install the compression gauge
(1).
SMIL14CEX3447BB 4
5. To measure the compression pressure proceed as fol-
lows:
• Turn the starter and read the compression pressure
when the compression gauge indicator is stable at
about 200 RPM.
• Measure the compression pressure for all cylinders.
Standard value: 3240 kPa (470 psi).
Limit value: 2260 kPa (328 psi).
Difference between each cylinder: 294 kPa
(43 psi)
NOTE: Be careful of the streaming air blowing out from the
glow plug hole while rotating.
NOTE: If the key switch is turned ON with the injector har-
ness connector removed, the ECM judges that it is a mal-
function and a diagnostic trouble code is set. Be sure to
clear DTCs after the inspection is complete.
51481238 06/06/2018
10.1 [10.001] / 23
28. Engine - Engine and crankcase
Crankcase - Remove
Battery ground cable disconnect
1. Disconnect the battery ground cable from the battery.
NOTICE: While the indicator (LED) of the battery discon-
nect switch is lit, do not turn OFF the battery disconnect
switch or disconnect its negative cable from the battery.
(After key OFF, lit for a maximum duration of 3 min)
Coolant drain
CAUTION
Burn hazard!
Hot coolant can spray and scald if you remove
the radiator or deaeration tank cap while the
system is hot. To remove the cap: allow the
system to cool, turn the cap to the first notch,
and wait for all pressure to release. Remove the
cap only after all pressure has released.
Failure to comply could result in minor or mod-
erate injury.
C0174A
1. Remove the radiator cap from the radiator.
2. Remove the drain plug from the radiator.
3. Drain coolant from the radiator.
NOTE: If the EGR cooler has an air bleeding plug (1),
loosen the plug and remove it with the gasket (2).
With the pressurized reserve tank specification, it is not
necessary to bleed the air.
SMIL14CEX2956AB 1
4. Remove the drain plug (1) from the cylinder block.
5. Discharge coolant from the engine.
6. Install the drain plug (1) to the cylinder block.
7. Install the drain plug to the radiator.
SMIL14CEX2973AB 2
Engine oil drain
1. Remove the drain plug from the oil pan.
2. Drain the engine oil from the oil pan.
3. Install the drain plug to the oil pan.
Tightening torque: 70 N·m (52 lb ft)
51481238 06/06/2018
10.1 [10.001] / 24
29. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
30. Engine - Engine and crankcase
Engine harness disconnect
1. Disconnect the engine harness from the engine assem-
bly.
NOTE: Disconnect each connector.
Cooling fan removal
1. Remove the cooling fan (1) from the adapter (2).
SMIL14CEX3121AB 3
Fan guide removal
1. Remove the fan guide (6) from the fan guide bracket.
1. Bolt
2. Washer
3. Rubber mount
4. Rubber mount
5. Guide tube
2. Remove the fan guide bracket from the engine assem-
bly.
SMIL14CEX3122AB 4
Cooling fan belt removal
1. Remove the cooling fan belt from the engine assembly.
1. Adjust bolt
2. Fixing bolt
3. Fixing bolt
SMIL14CEX3123AB 5
Crankshaft pulley removal
1. Remove the crankshaft pulley from the crankshaft.
2. Remove the crankshaft damper from the crankshaft
pulley.
51481238 06/06/2018
10.1 [10.001] / 25
31. Engine - Engine and crankcase
Crankshaft front oil seal removal
1. Remove the crankshaft front oil seal (3) from the timing
gear case.
NOTICE: Be careful not to damage the oil seal press-fitting
surface of the timing gear case.
1. Felt
2. Slinger
SMIL14CEX3124AB 6
2. Remove the slinger from the crankshaft using the spe-
cial tool.
Special tool: Slinger puller (Refer to Crankshaft -
Special tools (10.103))
SMIL14CEX3125AA 7
NOTICE: When replacing the oil seal, replace the slinger.
SMIL14CEX3126AA 8
Water pump assembly removal
1. Remove the fan pulley from the water pump assembly.
SMIL14CEX3127AA 9
51481238 06/06/2018
10.1 [10.001] / 26
32. Engine - Engine and crankcase
2. Remove the water bypass hose (1) from the water
pump assembly and the water duct.
3. Remove the water hose from the EGR cooler water
pipe and the water pump assembly.
4. Remove the water pump assembly from the front cover.
SMIL14CEX3128AB 10
Front cover removal
1. Remove the adjust plate from the front cover.
2. Remove the front cover from the cylinder block.
Turbocharger assembly removal
1. Remove the air cleaner duct from the air cleaner as-
sembly and the turbocharger assembly.
2. Remove the air intake hose from the turbocharger as-
sembly and the intercooler.
3. Remove the exhaust pipe from the turbocharger.
4. Disconnect the oil feed pipe (1) from the turbocharger
assembly.
NOTE: Remove the clip (2).
5. Remove the oil feed pipe (1) from the pipe bracket.
NOTE: Remove the clip (2).
6. Disconnect the oil return pipe (3) from the turbocharger
assembly.
7. Remove the oil return pipe (3) from the cylinder block.
8. Disconnect the water return pipe (5) from the tur-
bocharger assembly.
9. Remove the water return pipe (5) from the cylinder
head assembly.
10. Disconnect the water feed pipe (4) from the tur-
bocharger assembly.
NOTE: Remove the clip (2).
11. Remove the water feed pipe (4) from the cylinder
block.
NOTE: Remove the clip (2).
12. Disconnect the harness connector from the tur-
bocharger assembly.
SMIL14CEX2955AB 11
13. Remove the turbocharger assembly from the exhaust
manifold.
51481238 06/06/2018
10.1 [10.001] / 27
33. Engine - Engine and crankcase
EGR gas temperature sensor 1 removal
1. Disconnect the harness connector from EGR gas tem-
perature sensor 1 (1).
2. Remove the harness bracket from the fan guide stay.
3. Remove EGR gas temperature sensor 1 (1) from EGR
pipe A.
SMIL14CEX2980AB 12
EGR gas temperature sensor 2 removal
1. Disconnect the harness connector from EGR gas tem-
perature sensor 2 (1).
2. Remove the harness bracket from EGR pipe B.
3. Remove EGR gas temperature sensor 2 (1) from EGR
pipe B.
SMIL14CEX2981AB 13
EGR cooler removal
1. Disconnect the water rubber hose (1) from the EGR
cooler.
SMIL14CEX2959AB 14
51481238 06/06/2018
10.1 [10.001] / 28
34. Engine - Engine and crankcase
2. Remove the EGR pipe B (2) from the EGR valve (1)
and the EGR cooler C (3).
SMIL14CEX2983AB 15
3. Remove the EGR cooler C (1) from the EGR bracket C
(2).
4. Remove the EGR bracket C (2) from the EGR cooler B
(3).
5. Remove the EGR cooler B (3) from the EGR cooler
bracket A (4).
6. Remove the EGR cooler bracket A (4) from the EGR
cooler A.
SMIL14CEX2961AB 16
7. Remove the EGR heat protector (1) from the EGR pipe
A.
SMIL14CEX2980AB 17
8. Remove the EGR cooler A (1) from the EGR pipe A (2).
9. Remove the EGR pipe A (2) from the exhaust manifold.
(3).
SMIL14CEX2986AB 18
51481238 06/06/2018
10.1 [10.001] / 29