Caterpillar Cat 740 GC ARTICULATED TRUCK (Prefix 3T8) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
740 GC ARTICULATED TRUCK

Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 740 GC ARTICULATED TRUCK 3T8
Configuration: 740 Articulated Truck 3T800001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
740 GC, 740 Ejector, 745 Articulated Truck Machine System
Media Number -M0082510-04 Publication Date -01/09/2015 Date Updated -23/08/2018
i06247808
Gear Pump (Hydraulic Fan) - Remove and Install
SMCS - 1387-010-GT; 5073-010-HFN
Removal Procedure
Start By:
a. Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove and Install".
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered, oil is cool before
removing any components or lines. Remove the oil filler cap only when
the engine is stopped, and the filler cap is cool enough to touch with
your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
740 Articulated Truck 3T800001-UP (MACHINE) POWERED BY C15 Engine(M008...
2020/1/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00798601
1. Remove coupling (1) from gear pump (2).
2. Disconnect two hoses (3) from gear pump (2) and lay the hoses aside.
2/3
2020/1/14

3. Remove two bolts (4) and the washers in order to remove gear pump (2) from the machine.
4. Remove O-ring seal (5) from gear pump (2).
Installation Procedure
1. Install gear pump (2) in the reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 14 22:49:24 UTC+0800 2020
3/3
2020/1/14

Shutdown SIS
Previous Screen
i06247935
Gear Pump (Hydraulic Fan) - Disassemble
SMCS - 1387-015-GT; 5073-015-HFN
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
Start By:
a. Remove the gear pump (Hydraulic Fan). Refer to Disassembly and Assembly, "Gear Pump
(Hydraulic Fan) - Remove and Install".
1. Remove O-ring seal (1) and two elbows (2) from gear pump (3).
1/5
2020/1/14

2. Place the gear pump on suitable cribbing and remove adapter (4). Remove four bolts (5) in
order to remove plate (6) from housing (7).
3. Remove two dowels (8), seal (9) and pressure plate (10) from housing (7).
4. Remove seal (11) and backup seal (12) from pressure plate (10).
2/5
2020/1/14

5. Remove gear shaft (13) and idler gear (14) from housing (7).
6. Remove pressure plate (15) from housing (7). Refer to step 4 in order to remove the seals.
7. Remove housing (7) from flange (16).
3/5
2020/1/14

8. Remove seal (17) from housing (7).
9. Use a suitable pin punch in order to remove lip seal (19) from flange (16). Use tool (A) and
remove two rings (20). Use the pin punch to remove lip seal (21).
Tue Jan 14 22:50:20 UTC+0800 2020
4/5
2020/1/14

Shutdown SIS
Previous Screen
i06248004
Gear Pump (Hydraulic Fan) - Assemble
SMCS - 1387-016-GT; 5073-016-HFN
Assembly Procedure
Table 1
Required Tools
A 1P-1857 Retaining Ring Pliers 1
B 1P-0510 Driver Gp 1
1. On assembly, lubricate all internal components with the lubricant that is being sealed.
1/5
2020/1/14

2. Use tool (B) to install lip seal (21) with the lip of the seal toward flange (16). Use tool (A)
to install two retaining rings (20) into the ring grooves in flange (16). Use tool (B) to install
lip seal (19) with the lip of the seal away from flange (16).
3. Install two dowels (18) into flange (16).
4. Install seal (17) into housing (7).
2/5
2020/1/14

5. Align housing (7) with the dowel in flange (16) and position the housing on the flange.
6. Install pressure plate (15) into housing (7). Refer to step 8 for the installation of the seals.
7. Install idler gear (14) and gear shaft (13) into housing (7).
3/5
2020/1/14

8. Install seal (11) and backup seal (12) into pressure plate (10).
9. Carefully install pressure plate (10) onto housing (7). Install seal (9) and two dowels (8).
10. Align plate (6) with the two dowels in housing (7) and install four bolts (5). Tighten the
bolts to a torque of 44.5 ± 3.5 N·m (33 ± 2.5 lb ft). Install adapter (4).
4/5
2020/1/14

11. Install two elbows (2) and O-ring seal (1) to gear pump (3).
End By:
a. Install the gear pump (Hydraulic Fan). Refer to Disassembly and Assembly, "Gear Pump
(Hydraulic Fan)- Install".
Tue Jan 14 22:51:15 UTC+0800 2020
5/5
2020/1/14

Shutdown SIS
Previous Screen
i06282891
Piston Pump (Brake, Fan, Hoist) - Disassemble
SMCS - 5070-015
Disassembly Procedure
Table 1
Required Tools
A 1P-0510 Driver Group 1
B 8H-0663 Bearing Puller Gp 1
Start By:
a. Remove the piston pump.
1. Remove bolts (1) and valve (2).
1/10
2020/1/14

2. Remove gasket (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove adjustment screw (4), housing (5), O-ring seal (6), spring (7), spring (8), and
retainer (9).
2/10
2020/1/14

4. Remove adjustment screw (10), nut (11), housing (12), O-ring seal (13), spring (14), spring
(15), retainer (17), and screw (16).
5. Remove spool (18) and spool (19).
3/10
2020/1/14

6. Remove bolts (20) and pump head (21).
7. Remove O-ring seals (22), port plate (23), and bearing cup (24).
4/10
2020/1/14

8. Remove O-ring seal (25), spring (26), and piston (27).
9. Remove piston (28) and bearing cone (29).
10. Remove shim (30).
5/10
2020/1/14

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

11. Turn the pump housing over 180 degrees and hold the components in the pump housing.
Remove pump housing (31) from bearing cone (32), swashplate (33), and rotating group
(34).
12. Remove shaft (35) and bearing cone (32) from swashplate (33) and rotating group (34).
13. Use Tooling (A) and a suitable press in order to remove shaft (35) from bearing cone (32).
6/10
2020/1/14

Caterpillar Cat 740 GC ARTICULATED TRUCK (Prefix 3T8) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

More from fucheng89

More from fucheng89 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 740 GC ARTICULATED TRUCK (Prefix 3T8) Service Repair Manual Instant Download.pdf