The document provides instructions for disassembling the final drive of a 324D excavator. It lists required tools and a multi-step process involving removing bolts, covers, gears, seals, and other components. Individual parts are removed using various tools, with notes on alignment marks, weights of parts, and cleaning requirements before disassembly. The overall process breaks the final drive down into its core sub-assemblies and parts.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...kesi7153062
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking parts for alignment and lifting the final drive assembly off the machine.
2. Removing the cover and internal gears, shafts, and carriers.
3. Pressing shafts out of carriers and lifting off additional parts like planetary carriers.
4. Driving out spring pins to separate remaining components.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...shudun96087
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking parts for alignment and lifting the final drive assembly off the machine.
2. Removing the cover and internal gears, shafts, and carriers.
3. Pressing shafts out of carriers and lifting off additional parts like planetary carriers.
4. Driving out spring pins to separate remaining components.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...qme229722
The document provides instructions for disassembling a final drive assembly. Key steps include:
1. Marking parts for alignment and securing the assembly to a repair stand using brackets.
2. Removing bolts and covers, lifting off heavy parts like the cover using lifting devices.
3. Dismantling internal components such as gears, plates, and plugs from the housing and covers.
Cleanliness is emphasized to prevent dirt from entering during reassembly.
The document provides instructions for disassembling a final drive assembly. It begins by removing the final drive and cleaning the components. Alignment marks are made and the assembly is mounted to a repair stand. Bolts are removed from the cover, which is then lifted off using brackets and a lifting device. Additional steps include removing bolts and gears from inside the cover. Thrust plates and plugs are also removed from the assembly.
The document provides instructions for disassembling a final drive assembly. Key steps include:
1. Marking parts for alignment and securing the assembly to a repair stand using brackets.
2. Removing bolts and covers, lifting off heavy parts like the cover using lifting devices.
3. Dismantling internal components such as gears, plates, and plugs from the housing and covers.
Cleanliness is emphasized to prevent dirt from entering during reassembly.
The document provides instructions for disassembling a final drive assembly. It begins by removing the final drive from the machine and mounting it on a repair stand. Various internal components are then removed from the final drive assembly housing in sequential order. These include the cover, thrust plate, carrier assembly, ring gears, and other planetary gear components. Detailed steps and accompanying illustrations are provided to guide the disassembly process. Cleanliness is emphasized to prevent dirt from entering the mechanism during disassembly.
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to disassemble the final drive. Key steps include removing the cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering mechanisms. Weights of removed parts are provided.
Caterpillar Cat 325D L Excavator (Prefix AZP) Service Repair Manual (AZP00001...yfbr995309
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking and removing the final drive cover, gears, carrier assemblies, and planetary components.
2. Using tools like retaining ring pliers and a press to remove rings and shafts.
3. Dismantling the carrier assemblies by driving out spring pins and removing gears and shafts.
The process separates the final drive into its main individual parts for repair or replacement.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...kesi7153062
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking parts for alignment and lifting the final drive assembly off the machine.
2. Removing the cover and internal gears, shafts, and carriers.
3. Pressing shafts out of carriers and lifting off additional parts like planetary carriers.
4. Driving out spring pins to separate remaining components.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...shudun96087
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking parts for alignment and lifting the final drive assembly off the machine.
2. Removing the cover and internal gears, shafts, and carriers.
3. Pressing shafts out of carriers and lifting off additional parts like planetary carriers.
4. Driving out spring pins to separate remaining components.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...qme229722
The document provides instructions for disassembling a final drive assembly. Key steps include:
1. Marking parts for alignment and securing the assembly to a repair stand using brackets.
2. Removing bolts and covers, lifting off heavy parts like the cover using lifting devices.
3. Dismantling internal components such as gears, plates, and plugs from the housing and covers.
Cleanliness is emphasized to prevent dirt from entering during reassembly.
The document provides instructions for disassembling a final drive assembly. It begins by removing the final drive and cleaning the components. Alignment marks are made and the assembly is mounted to a repair stand. Bolts are removed from the cover, which is then lifted off using brackets and a lifting device. Additional steps include removing bolts and gears from inside the cover. Thrust plates and plugs are also removed from the assembly.
The document provides instructions for disassembling a final drive assembly. Key steps include:
1. Marking parts for alignment and securing the assembly to a repair stand using brackets.
2. Removing bolts and covers, lifting off heavy parts like the cover using lifting devices.
3. Dismantling internal components such as gears, plates, and plugs from the housing and covers.
Cleanliness is emphasized to prevent dirt from entering during reassembly.
The document provides instructions for disassembling a final drive assembly. It begins by removing the final drive from the machine and mounting it on a repair stand. Various internal components are then removed from the final drive assembly housing in sequential order. These include the cover, thrust plate, carrier assembly, ring gears, and other planetary gear components. Detailed steps and accompanying illustrations are provided to guide the disassembly process. Cleanliness is emphasized to prevent dirt from entering the mechanism during disassembly.
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to disassemble the final drive. Key steps include removing the cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering mechanisms. Weights of removed parts are provided.
Caterpillar Cat 325D L Excavator (Prefix AZP) Service Repair Manual (AZP00001...yfbr995309
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking and removing the final drive cover, gears, carrier assemblies, and planetary components.
2. Using tools like retaining ring pliers and a press to remove rings and shafts.
3. Dismantling the carrier assemblies by driving out spring pins and removing gears and shafts.
The process separates the final drive into its main individual parts for repair or replacement.
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to disassemble the final drive. Key steps include removing the cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering parts. Weights of components are provided to assist with lifting.
Caterpillar Cat 325D L Excavator (Prefix AZP) Service Repair Manual (AZP00001...shudun96087
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking and removing the final drive cover, gears, carrier assemblies, and planetary components.
2. Using tools like retaining ring pliers and a press to remove rings and shafts.
3. Dismantling the carrier assemblies by driving out spring pins and separating planetary gears.
The process requires cleaning components and noting part locations for reassembly.
Caterpillar Cat 325D L Excavator (Prefix AZP) Service Repair Manual (AZP00001...kesi7153062
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking and removing the final drive cover, gears, carrier assemblies, and planetary components.
2. Using tools like retaining ring pliers and a press to remove rings and shafts.
3. Dismantling the carrier assemblies by driving out spring pins and separating planetary gears.
The process requires cleaning components and noting part locations for reassembly.
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to disassemble the final drive. Key steps include removing the cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering parts. Weights of components are provided to assist with lifting.
The document provides instructions for disassembling a final drive component. It lists required tools and a multi-step process. Key steps include removing the final drive from the machine, draining fluids, and disassembling internal parts like gears, shafts, seals and housings using various tools. Cleanliness is emphasized throughout the process. Disassembly is done in reverse order of assembly.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...kesi7153062
The document provides instructions for disassembling a final drive component. It lists required tools and a multi-step process. Key steps include removing the final drive cover, carrier assembly, ring gears, and other internal parts using various tools. Cleanliness is important during disassembly to prevent dirt from entering the mechanism. Disassembly involves separating, lifting, and removing over 30 individual parts in a specific sequence.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...shudun96087
The document provides instructions for disassembling a final drive component. It lists required tools and a multi-step process. Key steps include removing the final drive from the machine, draining fluids, and disassembling internal parts like gears, shafts, seals and housings using various tools. Cleanliness is emphasized throughout the process. Disassembly is done in reverse order of assembly.
The document provides instructions for disassembling a final drive component. It lists required tools and a multi-step process. Key steps include removing the final drive cover, carrier assembly, ring gears, and other internal parts using various tools. Cleanliness is important during disassembly to prevent dirt from entering the mechanism. Disassembly involves separating, lifting, and removing over 30 individual parts in a specific sequence.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...yfbr995309
The document provides instructions to disassemble a final drive. Key steps include:
1. Marking the final drive for alignment and securing it in a repair stand.
2. Removing bolts and brackets to detach the cover and internal gears.
3. Using tools like retaining ring pliers to remove retaining rings and separate components like carrier assemblies and planetary gears.
4. Employing a press and hammer/punch to separately remove shafts and pins from disassembled parts.
Cleanliness is emphasized and weights of parts are provided.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336F and 336F L Excavator (Prefix DSW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 345D L Excavator (Prefix JKN) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, bearings and other components into the travel motor housing and barrel. Measurements are taken throughout to ensure proper assembly. The travel motor is then installed on the excavator and filled with the correct oil type.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar Cat 336E L Excavator (Prefix BZY) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstalling parts. Special care must be taken when handling springs or parts under spring force to avoid injury.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It describes 37 steps to disassemble the final drive by removing gears, shafts, housings, seals and other components. It then describes 34 steps to reassemble the final drive, including pressing in new bearings, installing seals, adjusting bearing preload with shims, and applying threadlocker to bolts. Precise tools and lifting devices are required due to the heavy weights of up to 550 kg involved.
Caterpillar Cat 336E L Excavator (Prefix DPX) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor on a 336E L excavator. The disassembly process involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and ensuring proper alignment of components.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fskekkdmdmdm3e
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It describes removing over 30 components of the travel motor including the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates and more.
3) Detailed illustrations are provided to accompany each step showing how to remove each component using the recommended tools.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, in reverse order, including attaching lifting devices, positioning the assembly, and reinstalling hoses and covers. Tools and torque specifications are provided.
More Related Content
Similar to Caterpillar Cat 324D and 324D L Excavator (Prefix MND) Service Repair Manual Instant Download.pdf
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to disassemble the final drive. Key steps include removing the cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering parts. Weights of components are provided to assist with lifting.
Caterpillar Cat 325D L Excavator (Prefix AZP) Service Repair Manual (AZP00001...shudun96087
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking and removing the final drive cover, gears, carrier assemblies, and planetary components.
2. Using tools like retaining ring pliers and a press to remove rings and shafts.
3. Dismantling the carrier assemblies by driving out spring pins and separating planetary gears.
The process requires cleaning components and noting part locations for reassembly.
Caterpillar Cat 325D L Excavator (Prefix AZP) Service Repair Manual (AZP00001...kesi7153062
The document provides instructions to disassemble the final drive of an excavator. Key steps include:
1. Marking and removing the final drive cover, gears, carrier assemblies, and planetary components.
2. Using tools like retaining ring pliers and a press to remove rings and shafts.
3. Dismantling the carrier assemblies by driving out spring pins and separating planetary gears.
The process requires cleaning components and noting part locations for reassembly.
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to disassemble the final drive. Key steps include removing the cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering parts. Weights of components are provided to assist with lifting.
The document provides instructions for disassembling a final drive component. It lists required tools and a multi-step process. Key steps include removing the final drive from the machine, draining fluids, and disassembling internal parts like gears, shafts, seals and housings using various tools. Cleanliness is emphasized throughout the process. Disassembly is done in reverse order of assembly.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...kesi7153062
The document provides instructions for disassembling a final drive component. It lists required tools and a multi-step process. Key steps include removing the final drive cover, carrier assembly, ring gears, and other internal parts using various tools. Cleanliness is important during disassembly to prevent dirt from entering the mechanism. Disassembly involves separating, lifting, and removing over 30 individual parts in a specific sequence.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...shudun96087
The document provides instructions for disassembling a final drive component. It lists required tools and a multi-step process. Key steps include removing the final drive from the machine, draining fluids, and disassembling internal parts like gears, shafts, seals and housings using various tools. Cleanliness is emphasized throughout the process. Disassembly is done in reverse order of assembly.
The document provides instructions for disassembling a final drive component. It lists required tools and a multi-step process. Key steps include removing the final drive cover, carrier assembly, ring gears, and other internal parts using various tools. Cleanliness is important during disassembly to prevent dirt from entering the mechanism. Disassembly involves separating, lifting, and removing over 30 individual parts in a specific sequence.
Caterpillar Cat 325D L Excavator (Prefix DBH) Service Repair Manual (DBH00001...yfbr995309
The document provides instructions to disassemble a final drive. Key steps include:
1. Marking the final drive for alignment and securing it in a repair stand.
2. Removing bolts and brackets to detach the cover and internal gears.
3. Using tools like retaining ring pliers to remove retaining rings and separate components like carrier assemblies and planetary gears.
4. Employing a press and hammer/punch to separately remove shafts and pins from disassembled parts.
Cleanliness is emphasized and weights of parts are provided.
Similar to Caterpillar Cat 324D and 324D L Excavator (Prefix MND) Service Repair Manual Instant Download.pdf (9)
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336F and 336F L Excavator (Prefix DSW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 345D L Excavator (Prefix JKN) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, bearings and other components into the travel motor housing and barrel. Measurements are taken throughout to ensure proper assembly. The travel motor is then installed on the excavator and filled with the correct oil type.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar Cat 336E L Excavator (Prefix BZY) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstalling parts. Special care must be taken when handling springs or parts under spring force to avoid injury.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It describes 37 steps to disassemble the final drive by removing gears, shafts, housings, seals and other components. It then describes 34 steps to reassemble the final drive, including pressing in new bearings, installing seals, adjusting bearing preload with shims, and applying threadlocker to bolts. Precise tools and lifting devices are required due to the heavy weights of up to 550 kg involved.
Caterpillar Cat 336E L Excavator (Prefix DPX) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor on a 336E L excavator. The disassembly process involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and ensuring proper alignment of components.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fskekkdmdmdm3e
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It describes removing over 30 components of the travel motor including the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates and more.
3) Detailed illustrations are provided to accompany each step showing how to remove each component using the recommended tools.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, in reverse order, including attaching lifting devices, positioning the assembly, and reinstalling hoses and covers. Tools and torque specifications are provided.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLC) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for removing and installing a crankshaft wear sleeve and crankshaft gear on a 325C excavator. It describes using various tools to distort and remove the existing wear sleeve and instructions for installing a new sleeve using a multi-piece installer tool. It also outlines steps for removing the crankshaft gear using a bearing puller and installing the gear by heating it and pressing it onto the crankshaft. The document provides maintenance technicians with detailed parts and tool information as well as safety notices for completing these tasks.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required include drivers, link brackets, guide studs, and installation tools.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306B engine. It describes:
1) Marking the gears to ensure proper timing during removal and installation.
2) Removing the camshaft bolts and carefully removing the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before installation.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
The document provides instructions for removing and installing various components of a Caterpillar 621E wheel scraper, including:
1) Removing and installing the push-pull plate that connects the push-pull spring to the support assembly.
2) Disassembling and assembling the push-pull spring itself by removing discs and plates.
3) A detailed process for removing and installing the ejector cylinder, which requires the use of lifting tools and wood blocks due to the cylinder's weight.
4) Brief instructions for removing and adjusting the position of the lower front and guide rollers on the ejector assembly.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
4/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
5/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
6/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
7/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
8/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
9/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
10/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engi...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 20 g00708211
25. Remove shims (27) from the main housing.
Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
11/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engi...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 09:56:29 UTC+0800 2020
12/12
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engi...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D EXCAVATOR MND
Configuration: 324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8646-22 Publication Date -01/02/2015 Date Updated -12/09/2018
i03508206
Final Drive - Disassemble
SMCS - 4050-015
S/N - A3R1022-UP
S/N - BFC1-UP
S/N - BYS1-UP
S/N - CYW1-UP
S/N - CZF1-UP
S/N - DBH380-UP
S/N - DJF1-UP
S/N - DTZ1-UP
S/N - EBM1-UP
S/N - EJC644-UP
S/N - GPB802-UP
S/N - J8D1-UP
S/N - J9D1-UP
S/N - JAT1-UP
S/N - JHJ1-UP
S/N - JJG814-UP
1/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
Start By:
a. Start by removing the final drive. Refer to Disassembly and Assembly, "Final Drive -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
Illustration 1 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
3/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 2 g00892883
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
Illustration 3 g00892888
5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
Illustration 4 g00892906
6. Remove O-ring seals (7) from plugs (5).
4/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 5 g00892930
7. Remove gear (8) and spacer (9).
Illustration 6 g00892965
8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
Illustration 7 g00892968
10. Remove retaining ring (15).
5/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 8 g00892975
11. Remove carrier assembly (16).
Illustration 9 g01389804
12. Use a suitable press to remove the shafts from carrier assembly (16).
Illustration 10 g00892977
6/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 13. Remove gear (17) and spacer (18).
Illustration 11 g00892997
14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 12 g00893019
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
Illustration 13 g00896860
16. Drive spring pin (23) into planetary shaft (22).
7/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 14 g00893043
17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
Illustration 15 g00896863
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
Illustration 16 g01842853
20. Remove gear (27). Remove spacer (27A).
8/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 17 g01842974
21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 18 g01843140
22. Drive spring pin (30) into shaft (29).
Illustration 19 g00893658
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
9/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engine...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 20 g00893674
24. Remove washers (31) and bearings (32) from planetary gear (33).
25. Repeat Steps 22 through 24 for the other three planetary gears.
Illustration 21 g01208300
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
Illustration 22 g01208542
10/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engi...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. 27. Remove O-ring seal (36) from sprocket housing (35).
Illustration 23 g01208553
28. Remove bolts (37) from coupling gear (38).
Illustration 24 g01208572
29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly in
order to loosen coupling gear (38). Remove the coupling gear from the motor housing.
Illustration 25 g01208578
11/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engi...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 26 g01208625
30. Remove shims (40) from the motor housing.
Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
approximately 109 kg (240 lb).
Illustration 27 g01208626
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
12/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engi...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
25. Illustration 28 g01208633
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
37. Remove the bearing cups from the sprocket housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 09:57:28 UTC+0800 2020
13/13
324D & 324D L Excavators MND00001-UP (MACHINE) POWERED BY C7 Engi...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...